2. Computers & electronics
  3. TVs & monitors
  4. Wall & ceiling mounts accessories
  5. Western
  6. MVP PLUS 8-1/2'/9-1/2' Blade Wing Extension Kit #44510-1

Western MVP PLUS 8-1/2'/9-1/2' Blade Wing Extension Kit #44510-1 Parts List & Installation Instructions

  • I have read the Western Products Blade Wing Extension Kit 44510-1 Parts List & Installation Instructions and am ready to answer your questions about its components and installation. The document provides a parts list that contains all hardware and parts to install the kit, as well as step by step instructions describing how to attach the wing extensions to your snowplow.
  • What parts are included in the Blade Wing Extension Kit?
    What is the first step in installing the blade wing kit?
    How to secure the wing after aligning the holes?
Lit. No. 44518, Rev. 03 1 March 15, 2009
PARTS LIST
CAUTION
Use standard methods and practices
when attaching snowplow and installing
accessories including proper personal
protective safety equipment.
CAUTION
See your WESTERN® outlet/Web site for
specifi c vehicle application recommendations
before installation. Blade wing weight
information may be found in the Selection List.
CAUTION
Read this document before installing the
blade wing kit.
WARNING
Do not exceed GVWR or GAWR, including
blade and ballast. The rating label is found on
the driver-side vehicle door cornerpost.
A DIVISION OF DOUGLAS DYNAMICS, L.L.C.
Western Products
PO Box 245038
Milwaukee, WI 53224-9538
www.westernplows.com
44510-1 – 8-1/2' & 9-1/2'
MVP PLUS™ Blades
BLADE WING EXTENSION KIT
Parts List & Installation Instructions
2
3
4
5
1
6
44510-1 Blade Wing Extension Kit
Item Part Qty Description Item Part Qty Description
1 44511 1 Blade Wing Extension – DS 4 44508 2 Cutting Edge Blade Wing Extension
ns 44512 1 Blade Wing Extension – PS 5 91337 4 5/8-11 Hex Locknut GB Topring
2 90264 4 5/8-11 x 3 Carriage Bolt G5 6 67921 2 5/8 x 4-3/4 Hitch Pin
3 44507 2 Bar Clamp
ns = not shown G = Grade
Lit. No. 44518, Rev. 03 2 March 15, 2009
44510-1 BLADE WING EXTENSION KIT
Copyright © 2009 Douglas Dynamics, L.L.C. All rights reserved. This material may not be reproduced or copied, in whole or in part, in any
printed, mechanical, electronic, fi lm or other distribution and storage media, without the written consent of Western Products. Authorization to
photocopy items for internal or personal use by Western Products outlets or snowplow owner is granted.
Western Products reserves the right under its product improvement policy to change construction or design details and furnish equipment when
so altered without reference to illustrations or specifi cations used. Western Products or the vehicle manufacturer may require or recommend
optional equipment for snow removal. Do not exceed vehicle ratings with a snowplow. Western Products offers a limited warranty for all
snowplows and accessories. See separately printed page for this important information. The following are registered (®) or unregistered (™)
trademarks of Douglas Dynamics, L.L.C.: MVP PLUS™, UltraMount®, WESTERN®.
Printed in U.S.A.
INSTALLATION INSTRUCTIONS
1. Park the vehicle on a smooth, level, hard surface,
such as concrete. Lower the blade to the ground,
and turn the control to the "OFF" position.
Disconnect the snowplow from the vehicle, or
turn the vehicle ignition to the "OFF" position and
remove the key.
2. Insert the wing studs into the holes in the
outermost rib.
3. Rotate the wing until the holes in the bracket on
the blade align with the holes in the wing arm.
4. Insert the hitch pin into the wing arm and bracket
holes, and secure with the hairpin cotter.
5. Repeat Steps 2–4 on the other side.
Hitch
Pin
Wing
Stud
Wing
Arm
Bracket
/