ICP DAS USA M-7015 User manual

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

1

I-7013, I-7015, I-7033, M-7013,

M-7015 and M-7033 Series

User Manual

Warranty

All products manufactured by ICP DAS are under

warranty regarding defective materials for a period of one

year from the date of delivery to the original purchaser.

Warning

ICP DAS assumes no liability for damages resulting

from the use of this product. ICP DAS reserves the right

to change this manual at any time without notification.

The information furnished by ICP DAS is believed to be

accurate and reliable. However, no responsibility is

assumed by ICP DAS for its use, or for any infringements

of patents or other rights of third parties resulting from its

use.

Copyright

Trademark

The names used for identification only may be

registered trademarks of their respective companies.

Date: 2015/01/12

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

2

Table of Contents

1. Introduction ................................................................................ 6

1.1 More Information ............................................................... 8

1.2 Terminal Assignment ......................................................... 9

1.3 Specifications ................................................................... 13

1.4 Block Diagrams ................................................................ 15

1.4.1 Block Diagram for the I-7013 and I-7013D ........... 15

1.4.2 Block Diagram for the I-7033, I-7033D, M-7033

and M-7033D ................................................................... 15

1.4.3 Block Diagram for the I-7015, I-7015P, M-7015

and M-7015P .................................................................... 16

1.4.4 Block Diagram for the M-7013P and M-7013PD . 16

1.5 Dimensions ....................................................................... 17

1.5.1 I-7013, I-7013D, I-7033, I-7033D, M-7033 and M-

7033D Dimensions ........................................................... 17

1.5.2 I-7015, I-7015P, M-7013P, M-7013PD, M-7015 and

M-7015P Dimensions ...................................................... 18

1.6 Wiring .............................................................................. 19

1.6.1 Wiring diagram for the I-7013, I-7013D, I-7033, I-

7033D, M-7033 and M-7033D ........................................ 19

1.6.2 Wiring diagram for the I-7015, I-7015P, M-7015

and M-7015P .................................................................... 20

1.6.3 Wiring diagram for the M-7013P and M-7013PD 20

1.6.4 Wiring Recommendations ...................................... 21

1.7 Quick Start ....................................................................... 22

1.8 Default Settings ................................................................ 24

1.9 Calibration ........................................................................ 25

1.10 Configuration Tables ..................................................... 27

1.11 M-7000 Notes ................................................................ 35

1.11.1 Protocol Switching ................................................ 35

1.11.2 INIT Mode ............................................................ 36

1.12 Mounting ........................................................................ 37

1.12.1 Din-Rail Mounting ................................................ 37

1.12.2 Piggyback Mounting ............................................. 39

1.12.3 Wall Mounting ...................................................... 40

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

3

1.13 Technical Support .......................................................... 41

2. DCON Protocol ........................................................................ 42

2.1 %AANNTTCCFF ............................................................ 46

2.2 #** .................................................................................... 50

2.3 #AA .................................................................................. 52

2.4 #AAN ............................................................................... 54

2.5 $AA0 ................................................................................ 56

2.6 $AA1 ................................................................................ 58

2.7 $AA0Ci ............................................................................ 60

2.8 $AA1Ci ............................................................................ 62

2.9 $AA2 ................................................................................ 64

2.10 $AA4 .............................................................................. 66

2.11 $AA5 .............................................................................. 68

2.12 $AA5VV ........................................................................ 70

2.13 $AA6 .............................................................................. 72

2.14 $AA7CiRrr ..................................................................... 74

2.15 $AA8Ci .......................................................................... 76

2.16 $AA8 .............................................................................. 78

2.17 $AA8V ........................................................................... 80

2.18 $AA9(Data) .................................................................... 82

2.19 $AAB ............................................................................. 84

2.20 $AAF .............................................................................. 86

2.21 $AAI ............................................................................... 87

2.22 $AAM ............................................................................ 89

2.23 $AAP .............................................................................. 90

2.24 $AAPN ........................................................................... 92

2.25 $AAS0 ............................................................................ 94

2.26 $AAS1 ............................................................................ 96

2.27 ~AAD ............................................................................. 98

2.28 ~AADVV ..................................................................... 100

2.29 ~AAEV ........................................................................ 102

2.30 ~AAI (Soft INIT command) ........................................ 104

2.31 ~AAO(Name) ............................................................... 106

2.32 ~AATnn ....................................................................... 108

2.33 ~** ................................................................................ 111

2.34 ~AA0 ............................................................................ 112

2.35 ~AA1 ............................................................................ 114

2.36 ~AA2 ............................................................................ 116

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

4

2.37 ~AA3EVV .................................................................... 118

2.38 ~AA4 ............................................................................ 120

2.39 ~AA5PPSS ................................................................... 122

2.40 @AACA ....................................................................... 124

2.41 @AACE ....................................................................... 126

2.42 @AADA ...................................................................... 128

2.43 @AADI ........................................................................ 130

2.44 @AADODD ................................................................. 132

2.45 @AAEAT .................................................................... 134

2.46 @AAHI(data) ............................................................... 136

2.47 @AALO(data).............................................................. 138

2.48 @AARE ....................................................................... 140

2.49 @AARH ....................................................................... 142

2.50 @AARL ....................................................................... 144

3. Modbus RTU Protocol ........................................................... 146

3.1 02 (0x02) Read Input Status .......................................... 147

3.2 04 (0x04) Read Input Channels ..................................... 148

3.3 70 (0x46) Read/Write Module Settings ......................... 149

3.3.1 Sub-function 00 (0x00) Read module name ......... 150

3.3.2 Sub-function 04 (0x04) Set module address ........ 151

3.3.3 Sub-function 05 (0x05) Read communication

settings ............................................................................ 152

3.3.4 Sub-function 06 (0x06) Set communication settings

........................................................................................ 154

3.3.5 Sub-function 07 (0x07) Read type code ............... 156

3.3.6 Sub-function 08 (0x08) Set type code .................. 157

3.3.7 Sub-function 32 (0x20) Read firmware version ... 158

3.3.8 Sub-function 37 (0x25) Read channel

enabled/disabled status ................................................... 159

3.3.9 Sub-function 38 (0x26) Set channel enable/disable

........................................................................................ 160

3.3.10 Sub-function 41 (0x29) Read miscellaneous

settings ............................................................................ 161

3.3.11 Sub-function 42 (0x2A) Write miscellaneous

settings ............................................................................ 162

3.3.12 Sub-function 49 (0x31) Read LED configuration

........................................................................................ 163

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

5

3.3.13 Sub-function 50 (0x32) Write LED configuration

........................................................................................ 164

3.4 M-7015/15P Address Mappings .................................... 165

3.5 M-7015/15P Engineering Data Format Table ............... 167

3.6 M-7013P Address Mappings ......................................... 168

3.7 M-7013P Engineering Data Format Table .................... 170

4. Troubleshooting ..................................................................... 171

4.1 Communicating with the module ................................... 172

4.2 Reading Data .................................................................. 173

A. Appendix ............................................................................... 174

A.1 INIT Mode .................................................................... 174

A.2 Dual Watchdog Operation ............................................ 176

A.3 Frame Ground ............................................................... 177

A.4 Node Information Area ................................................. 179

A.5 RTD ............................................................................... 180

A.6 Resistance Measurement ............................................... 181

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

6

1. Introduction

The I-7000 series is a family of network data acquisition

and control modules, providing analog-to-digital, digital-

to-analog, digital input/output, timer/counter and other

functions. The modules can be remotely controlled using a

set of commands, which we call the DCON protocol.

Communication between the module and the host is in

ASCII format via an RS-485 bi-directional serial bus

standard. Baud Rates are software programmable and

transmission speeds of up to 115.2 Kbps can be selected.

The functionality of the M-7000 series is the same as the

I-7000 series, with the exception that the M-7000 series

offers extended support for the Modbus RTU protocol.

Some I-7000 modules feature

a new design for the frame

ground and INIT switch as

shown in the figure (rear

view). The frame ground

provides enhanced static

protection (ESD) abilities and

ensures the module is more

reliable. The INIT switch

allows easier access to INIT

mode. Please refer to Sections

A.1 and A.3 for more details.

The common features of the I-7013/13D, I-7033/33D,

I-7015/15P, M-7013P/13PD, M-7015/15P, and

M-7033/33D modules are as follows:

1. 3000V DC inter-module isolation

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

7

2. 24-bit sigma-delta ADC to provide excellent accuracy

3. Direct RTD (resistance temperature detector)

connection

4. Software calibration

The I-7013/M-7013P is a single channel RTD input

module. The I-7013D/M-7013PD is the I-7013/M-7013P

with a 41/2 digit LED display. The I-7015/M-7015 is a

6-channel RTD input module. The I-7015P/M-7015P is a

6-channel RTD input module with lead resistances

elimination. The I-7033/M-7033 is a 3-channel RTD

input module. The I-7033D/M-7033D is the

I-7033/M-7033 with a 41/2 digit LED display.

Supported RTD types are as follows:

1. Platinum, 100 Ohms at 0°C, α = 0.00385

2. Platinum, 100 Ohms at 0°C, α = 0.003916

3. Platinum, 1000 Ohms at 0°C, α = 0.00385

(I-7013/13D firmware version B1.3 and later,

I-7033/33D, M-7033/33D, I-7015/15P and

M-7015/15P)

4. Nickel, 120 Ohms at 0°C, α = 0.00672

5. Copper, 100 Ohms at 0°C, α = 0.00421 (I-7015/15P

and M-7015/15P)

6. Copper, 1000 Ohms at 0°C, α = 0.00421 (I-7015/15P

and M-7015/15P)

7. Copper, 100 Ohms at 25°C, α = 0.00427 (I-7015/15P

and M-7015/15P)

8. Copper, 50 Ohms at 0°C, (I-7015/15P and M-7015/15P

firmware version A2.3 and later)

9. Nickel, 100 Ohms at 0°C, (I-7015/15P and

M-7015/15P firmware version A2.9 and later)

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

8

1.1 More Information

For more information regarding the I-7000 series, please

refer to chapter 1 of the “I-7000 Bus Converter User

Manual” as shown below or visit the ICP DAS website

http://www.icpdas.com.

1.1 The 7000 Series Overview

1.2 Related Documentation for the 7000 Series

1.3 Common Features of the 7000 Series

1.4 The 7000 Series System Network Configuration

1.5 7000 Dimensions

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

9

1.2 Terminal Assignment

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

10

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

11

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

12

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

13

1.3 Specifications

I-7013/I-7013D

I-7033/I-7033D

M-7033/M-7033D

I-7015/I-7015P

M-7015/M-7015P

Analog Input

Input Channels

1

3

6

Input Type

2/3/4-wire RTD

2/3-wire RTD

RTD Type

Pt100α = 0.00385

Pt100α = 0.003916

Ni120

Pt1000α = 0.00385

(for firmware version

B1.3 and later)

Pt100α = 0.00385

Pt100α = 0.003916

Ni120

Pt1000α = 0.00385

Pt100α = 0.00385

Pt100α = 0.003916

Ni120

Pt1000α = 0.00385

Cu100α = 0.00421

Cu100α = 0.00427

Cu1000α = 0.00421

Sampling Rate

10 samples/sec

15 samples/sec at 60Hz

12.5 samples/sec at 50Hz

12 samples/sec

Bandwidth

5.24 Hz

15.7 Hz

5.24 Hz

Accuracy

±0.05%

±0.1%

±0.05%

Zero Drift

0.5 µV/°C

Span Drift

20 µV/°C

CMR@50/60Hz

150 dB min

NMR@50/60Hz

100 dB min

Isolation

3000 VDC

Modbus RTU

M-7033/M-7033D

M-7015/M-7015P

LED Display

4 1/2 digits

(for I-7013D only)

4 1/2 digits

(for I-7033D and

M-7033D only)

Power

Requirements

+10 to +30 VDC

Consumption

0.7 W for I-7013

1.3 W for I-7013D

1.0 W for I-7033/M-7033

1.6 W for I-7033D/

M-7033D

1.1 W

Temperature

Range

Operating

-25°C to +75°C

Storage

-40°C to +85°C

Notes:

1. A warm up period of 30 minutes is recommended in order to achieve the complete

performance results described in the specifications.

2. The specifications are typical at 25°C unless otherwise stated.

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

14

M-7013P/M-7013PD

Analog Input

Input Channels

1

Input Type

2/3/4-wire RTD

RTD Type

Pt100α = 0.00385, Pt100α = 0.003916

Ni120, Pt1000α = 0.00385

Sampling Rate

10 samples/sec

Bandwidth

5.24 Hz

Accuracy

±0.05%

Zero Drift

0.5 µV/°C

Span Drift

20 µV/°C

CMR@50/60Hz

150 dB min

NMR@50/60Hz

100 dB min

Isolation

3000 VDC

Modbus RTU

Yes

Digital Input

Channels

1

Sink/Source (NPN/PNP)

Source, Dry Contact

ON Voltage Level

Close to GND

OFF Voltage Level

Open

Counter(50 Hz, 16-bit)

Yes

Digital Output

Channels

2

Type

Open Collector, MOSFET

Sink/Source (NPN/PNP)

Sink

Load Voltage

3.5 ~ 50 VDC

Max. Load Current

700 mA/Channel

Overvoltage Protection

60 VDC

LED Display

4 1/2 digits (forM-7013PD only)

Power

Requirements

+10 to +30 VDC

Consumption

0.6 W for M-7013P, 1.2 W for M-7013PD

Temperature Range

Operating

-25°C to +75°C

Storage

-40°C to +85°C

Notes:

1. A warm up period of 30 minutes is recommended in order to achieve the complete

performance results described in the specifications.

2. The specifications are typical at 25°C unless otherwise stated.

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

15

1.4 Block Diagrams

1.4.1 Block Diagram for the I-7013 and I-7013D

1.4.2 Block Diagram for the I-7033, I-7033D,

M-7033 and M-7033D

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

16

1.4.3 Block Diagram for the I-7015, I-7015P,

M-7015 and M-7015P

1.4.4 Block Diagram for the M-7013P and

M-7013PD

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

17

1.5 Dimensions

1.5.1 I-7013, I-7013D, I-7033, I-7033D, M-7033 and

M-7033D Dimensions

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

18

1.5.2 I-7015, I-7015P, M-7013P, M-7013PD, M-7015

and M-7015P Dimensions

Back View

Top View

Front View

Side View

Unit : mm

lnit

Normal

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

19

1.6 Wiring

1.6.1 Wiring diagram for the I-7013, I-7013D,

I-7033, I-7033D, M-7033 and M-7033D

2-wire RTD connection

3-wire RTD connection

4-wire RTD connecion

I-7013/15/33, M-7015/33 User Manual, Rev: B2.2 7PH-008-B22

20

1.6.2 Wiring diagram for the I-7015, I-7015P,

M-7015 and M-7015P

2-wire RTD connection

3-wire RTD connection

1.6.3 Wiring diagram for the M-7013P and

M-7013PD

Page is loading ...

ICP DAS USA M-7015 User manual

ICP DAS USA M-7015 User manual

Related papers

Other documents