BLADEZ AEROPRO H930 Owner's manual

AEROPRO H930

OWNER’S MANUAL

IMPORTANT:

Read all instructions carefully before using this product. Retain this owner’s

manual for future reference.

Tel.: 949 206-0330 Fax.: 949 206-0013 www.bhnorthamerica.com

BH North America Foothill Ranch , California 92610

TABLE OF CONTENTS

Safety 1

Training 2

Pre-Assembly Instructions 6

Assembly Instructions 7

Maintenance 11

Console Operations 12

Exploded View 15

Part List 16

Warranty 18

1

IMPORTANT SAFETY ADVICE

GENERAL INSTRUCTIONS

Carefully read through the instructions contained in this manual. It pro vides y ou with im portant info rmation

about assembly, safety and use of the machine.

1 This unit has be en designed for home use. The weight of the user must not exce ed 2 86 lbs. (13 0 kg.)

2 Parents and/or those responsible for childr en should always take their cur ious nature into account and

how this can often lead to hazardous situat ions and behavior resulting in a ccidents. Under no

circum stances should this applia nc e be use d as a toy.

3 The owner is re sponsible for ensuring that anyone who use s the machine is duly inform ed about the

necessary pre cautions.

PRECAUTIONS

This bike has been designed and constr ucted to provide max imum safety. N evertheless, certain prec autions

should be take n when using exe rc ise equipme nt . Re ad the entire m anual be fore assembling and using this

bike . The following safety pre cautions should also be obser ved:

1. Kee p c hildren or pets away from this equipme nt at all times. DO NO T leave them unsupervised in the

roomwherethisbikeiskept.

2. This bike can only be u sed by one per son at a time.

3. If y ou experience dizziness, nausea, chest pains or any other symptom while using this appliance STOP

the ex ercise. SEEK MEDICAL ATTENTION IMMEDIATELY!

4. Use the machine on a level, solid surface. Adjust the stab ilizer for assured stability.

5. Keep your hands w ell away from any of the m oving parts.

6. Do not use the machine outdoor or near the wate r

7. Wear clot hing suitable for doing ex er cise. Do not use baggy clot hing that might get caught up in the

m achine. A lways w ear running shoes or trainer s when using the machine. make sure all laces/cords are

ti red correctly

8. Thisappliancemustonlybeusedforthepurposesdescribedinthismanual.DONOTuseaccessories

that are not recomme nde d by the manufac turer.

9. Do not place shar p obje cts near the machine.

10. People with physical lim itations should not use the ma chine without the assistanc e of a qualified person

or a doctor.

11 . Do war m up str etching exe rcises before using the equipm ent.

12. Do not use the machine if it is not wor king cor rectly.

13. Review all the warnings and labels affixed to the machine; if damaged, illegible, or removed, order

replacements from BH N orth America Corporation.

Caution

Consult your doctor before beginning to use the bike. This advice is especially

important for those over 35 or suffering from health problems. Read all of the

instructions before using any exercise equipment.

KEEP THIS INSTRUCTION SAFE FOR FUTURE USE

AEROPRO

2

EXERCISE INSTRUCTIONS

Exercise offers various benefits; it will improve fitness, muscle tone and when used in conjunction with a calorie

controlled diet, it will help you to lose weight.

TRAINING GUIDELINES

Exercise is one of the most important factors in the overall health of an individual. Listed among its benefits are:

Increased capacity for physical work (strength endurance)

Increased cardiovascular (heart and arteries/veins) and respiratory efficiency

Decreased risk of coronary heart disease

Changes in body metabolism, e.g. losing weight

Delaying the physiological effects of age

Physio lo gical eff ects, e. g. r eduction in stress, increase in self-confidence, etc.

Basic Components of Physical Fitness

There are four all encompassing components of physical fitness and we need to briefly define each and clarify its

role

STRENGTH is the capacity of a muscle to exert a force against resistance. Strength contributes to power and

speed and is of great importance to a majority of sports people.

MUSC ULAR ENDURANCE i s the capaci ty to exert a force repeatedly over a peri od of time, e.g . it is the

of your legs to carry you 10 Km without s topping.

FLEXIBI L ITY is the range of motion about a joint. Improving flexibility involves the stretching of muscles and

tendons to maintain or increase suppleness, and provides increased resistance to muscle injury or soreness.

CARDIO-RESPIRATO RY EN DURANCE is the most essential component of physical fitness . It is the efficient

functioning of the heart and lungs .

AEROBIC FITNESS The largest amount of oxygen that you can use per minute during exercise is called your

maximum oxygen uptake (MVo2). T his is often referred to as your aerobic capacity

OXYGEN UPTAKE

The effort that you can exert over a prolonged period of time is limited by your ability to deliver oxygen to

the working muscles. Regular vigorous exercise produces a training effect that can increase your aerobic

capacity by as much as 20 to 30%. An increased MVO2 indicates an increased ability of the heart to pump

blood, of the lungs to ventilate oxygen and of the muscles to take up oxygen.

ANAEROBIC TRAINING

This means “without oxygen” and is the output of energy when the oxygen supply is insufficient to meet

the body’s long term energy demands. (For example, 100 meter sprint).

THE TRAINING THRESHOLD

This is the minimum level of exercise which is required to produce significant improvements in any

physical fitness parameter.

PROGRESSION

As your become more fit, a higher intensity of exercise is required to create an overload and therefore provide

continued improvement

OVERLOAD

This is where you exercise at a level above that which can be carried out comfortably. The intensity,

duration and frequency of exercis e should be above the training threshold and should be gradually

increased as the body adapts to the increasing demands. As your fitness level improves, the training

threshold should be raised. Working through your program and gradually increasing the overload factor is

important.

AEROPRO

TRAINING GUIDELINES (cont’d)

Specifics

Different forms of exercise produce different results. The type of exercise that is carried out is specific both to

the muscle groups being used and to the energy source involved.

There is little transfer of the effects of exercise, i.e. from strength training to cardiovascular fitness. That is why

it is important to have an exercise program tailored to your specific needs.

Reversibility

If you stop exercising or do not do your program often enough, you will lose the benefits you have gained.

Regular workouts are the key to success.

Warm Up

Every exercise program should start with a warm up where the body is prepared for the effort to come. It should

be gentle and preferably use the muscles to be involved later.

Stretching should be included in both your warm up and cool down, and should be performed after 3-5 minutes

of low intensity aerobic activity or callisthenic type exercise.

Warm Down or Cool Down

This involves a gradual decrease in the intensity of the exercise session. Following exercise, a large supply of

blood remains in the working muscles. If it is not returned promptly to the central circulation, pooling of blood

may occur in the muscles.

Heart Rate

As you exercise, the rate at which your heart beat increases. This is often used as a measure of the required

intensity of exercise. You need to exercise hard enough to condition your circulatory system, and increase your

pulse rate, but not enough to strain your heart.

Your initial level of fitness is important in developing an exercise program for you. If you are starting off you

can get a good training effect with a heart rate of 110-120 beats per minute (BPM). If you are more fit, you will

need a higher threshold of stimulation.

To begin with, you should exercise at a level that elevates your heart rate to about 65 to 70% of your maximum.

If you find this is too easy, you may want to increase it, but it is better to lean on the conservative side.

As a rule of thumb, the maximum heart rate is 220 minus your age. As you increase in age, your heart, like other

muscles, loses some of its efficiency. Some of its natural loss is won back as fitness improves. The following

table is a guide to those who are “starting fitness”.

Age Target heart Rate 25 30 35 40 45 50 55 60 65

10SecondCount 232222212019191818

Beats per Minute 138 132 132 126 120 114 114 108 108

Pulse Count

The pulse count (on your wrist or carotid artery in the neck, taken with two index fingers) is done for ten

seconds, taken a few s econds after you stop exercising. T his is for two reasons: (a) 10 seconds is long enough for

accuracy, (b) the pulse count is to approximate your BPM rate at the time you are exercising. Since heart rate

slows as you recover, a longer count isn’t as accurate.

3

AEROPRO

4

TRAINING GUIDELINES (cont’d)

The target is not a magic number, but a general guide. If you’re above average fitness, you may work

quite comfortably a little above that suggested for your age group.

The following table is a guide to those who are keeping fit. Here we are working at about 80% of

maximum.

Age 253035404550556065

Target heart Rate

10 Second Count 26 26 25 24 23 22 22 21 20

Beats per Minute 156 156 150 144 138 132 132 126 120

Don’t push yourself too hard to reach the figures on this table. It can be very uncomfortable if you

overdo it. Let it happen naturally as you work through your program. Remember, the target is a guide,

not a rule, a little above or below is just fine.

Two final comments:(1) don’t be concerned with day to day variations in your pulse rate, being under

pressure or not enough sleep can affect it;(2) your pulse rate is a guide, don’t become a slave to it.

Muscle Soreness

For the first week or so, this may be the only indication you have that you are on an exercise program.

This, of course, does depend on your overall fitness level. A confirmation that you are on the correct

program is a very slight soreness in most major muscle groups. This is quite normal and will disappear

in a matter of days.

If you experience major discomfort, you may be on a program that is too advanced or you have

increased your program too rapidly.

If you experience PAIN during or after exercise, your body is telling your something. Stop exercising

and consult your doctor.

What to Wear

Wear clothing that will not restrict your movement in any way while exercising. Clothes should be

light enough to allow the body to cool. Excessive clothing that causes you to perspire more than you

normally would while exercising, gives you no advantage. The extra weight you lose is body fluid and

will be replaced with the next glass of water you drink. It is advisable to wear a pair of gym or running

shoes or “sneakers”.

Breathing during Exercise

Do not hold your breath while exercising. Breathe normally as much as possible. Remember, breathing

involves the intake and distribution of oxygen, which feeds the working muscles.

Rest periods

Once you start your exercise program, you should continue through to the end. Do not break off

halfway through and then restart at the same place later on without going through the warm-up stage

again. The rest period required between strength training exercises may vary from person to person.

AEROPRO

5

TRAINING GUIDELINES (Cont’d)

The correct form for several basic stretches is shown at the right. Move slowly as you stretch -

never bounce.

1. Toe Touch Stretch

Stand with your knees bent slightly and slowly bend

forward from your hips. Allow your back and shoulders

to relax as you reach down toward your toes as far as

possible. Hold for 15 counts, then, relax. Repeat 3

times. Stretches: Hamstrings, Back of Knees, and Back.

2. Hamstring Stretch

Sit with one leg extended. Bring the sole of the opposite

foot toward you and rest it against the inner thigh of your

extended leg. Reach toward your toes as far as possible.

Hold for 15 counts, then, relax. Repeat 3 times for each

leg. Stretches: Hamstrings, Lower Back, and Groin.

3. Calf/Achilles Stretch

With one leg in front of the other, reach forward and

place your hands against a wall. Keep your back leg

straight and your back foot flat on the floor. Bend your

front leg lean forward and move your hips toward the

wall. Hold for 15 counts, then, relax. Repeat 3 times for

each leg. To cause further stretching of the Achilles

tendons, bend your back leg as well. Stretches: Calves,

Achilles tendons and ankles.

4. Quadriceps Stretch

With one hand against a wall for balance, reach back and

grasp one foot with your other hand. Bring your heel as

close to your buttocks as possible. Hold for 15 counts,

then, relax. Repeat 3 times for each leg. Stretches:

Quadriceps and hip muscles.

5. Inner Thigh Stretch

Sit with the soles of your feet together and your knees

outward. Pull your feet toward your groin areas far as

possible. Hold for 15 counts, then, relax. Repeat 3 times for

each leg. Stretches: Quadr iceps and hip muscles.

1

2

3

4

5

AEROPRO

PRE-ASSEMBLY

6

Fig.1

1 Monitor 3 Handlebar Stem

74 Main Body 5 Handlebar knob

4 Handlebar 28 Front Stabilizer

6 Flat washer 124 Seat

122 Rear Stabilizer 50R Right pedal

50L Left pedal 158 Flat washer M10

157 Slotted Head bolt M10 85 Bottle H older

2 Philips H ead Machine Screw 159 AC Adaptor

The assistance of a second person is recommended when assembling this unit

Take the unit out of its box and make sure all of the pieces are there (fig. 1)

AEROPRO

7

Fig. 2 : Stabilizer Assembly

A. Stabilizer Assembly

1. Position the machine’s rear on the Rear Stabilizer (122) as shown in figure 2. Tighten

securely using bolts (157) and Flat washers (158).

2. Position the front Stabilizer (28) with the wheels facing forward as shown in figure 2

paying attention to the red dots. Secure with the bolts (157) and Flat washers (158)

B. Pedals Assembly

Mounting the pedals incorrectly could damage the threads on either the pedals and/or the

crank. Therefore, the assembly instructions for the pedals must be followed to the letter.

Right and Left refer to the position that the user adopts when sitting on the seat to do the

exercises.

The Right-hand pedal, marked with the letter (50R), screws onto the right-hand crank, also

marked with an (R), in a clockwise direction. Tighten securely (Fig. 3).

The Left-hand pedal, marked with the letter (50L), screws onto the left-hand crank, also

marked with a letter (L), in a counter-clockwise direction. Tighten securely.

AEROPRO

8

Figure 3

Left Pedal

Tightening

Direction

Right Pedal

Tightening

Direction

C. Seat Assembly

Loosen knob (129) and slide the seat bracket (127) onto the horizontal seat tube (3).

Tighten knob (129). Attach the seat (124) onto the seat bracket (127) and tighten the nuts

on the seat securely.

· Seat Height Adjustment: loosen the seat post adjustment knob (83) slightly by turning it

counterclockwise a turn or two. Move the seat up/down to a desired height and tighten

the knob in the clockwise direction

· Seat Horizontal Adjustment: loosen the knob (129); move the seat to a position

comfortable for doing exercise and then tighten the knob (129)

D. Installing the Monitor

Remove the computer stem covers (7 &

8). Remove 4 screws (2) from the base

of the monitor (1) then connect the

terminal (14) to the terminal on the

monitor. Slide the monitor onto the

holding bracket and secure with the 4

screws removed earlier (fig. 8). Attach

the post covers (7 & 8) and tighten

screws (10) as in figure (9)

Fig. 8

Fig. 9

AEROPRO

127

9

D. Installing Handlebar

Place the handlebar (4) on the handlebar stem (3) and tighten knob (5) shown in Fig. 4. Insert

the handlebar stem into the main body (74) shown in Fig. 11 and tighten the knobs (83 & 87) by

turning them clockwise. Plug the connector (14) from the handlebar post into the connector (89)

fromthemainbody(74).Placethecap(15)andsecurewithscrews(13)(Fig.11)

· Handlebar Height Adjust: loosen knob (83 & 87) slightly by turning counterclockwise a turn

or two. Move the handlebar up/down to a desired height and tighten the knobs in the

clockwise direction. Pay attention not to go beyond MIN INSERT mark

· Handlebar Horizontal Adjust: loosen the knob (5) by turning counterclockwise; move the

handlebar to a distance comfortable for doing exercise and then tighten the knob (5).

Fig. 10

Fig. 11

E. Attaching Bottle Holder

Mount the bottle holder (85) to the side of

the front fork using screws (86) (fig. 11)

Leveling: once the unit has been placed into

its final position, make sure it sits flat and

level

on

the floor. If needed, make adjustment for

the footpads (121) by dialing the wheels (121)

on the sides of the stabilizers (Fig. 12)

Fig. 11

Fig. 12

AEROPRO

ASSEMBLY INSTRUCTIONS (cont’d)

10

Connecting Power: Mate the AC adaptor jack (c) into the plug toward the rear of the main body

(h) and the AC adaptor to a 110V wall outlet (fig. 13) to charge the backup battery.

Moving & Storage: the unit is equipped with wheels on the front stabilizer to make it easier to

move. Lift the rear of the unit up to put weight on the wheels then push to move (fig. 14). Store the

bike in a cool, dry place not subject to changes in temperature.

Maintenance: it is necessary to clean the handlebar, seat and frame after each exercise session

with a disinfectant spray.

Fig.14

Fig.13

BH RESERVES THE RIGHT TO MODIFY THE SPECIFICATIONS OF ITS PRODUCTS

WITHOUT PRIOR NOTICE

AEROPRO

MAINTENANCE INSTRUCTIONS

CLEANING

WARNING: Always unplug your elliptical prior to cleaning or servicing your unit, in order to avoid

electrical hazard or shock.

Care has been taken to assure that your machine has been properly adjusted and lubricated at the

factory. It is not recommended that the user attempt service on the internal components.

Instead, seek service from an authorized service center. However, from time to time, the outer

surfaces may appear dull or dirty. Follow the instructions below will restore and preserve the

original finish.

Cleaning metal surfaces may be accomplished by using a soft cotton or terry cloth rag with a

light application of car wax. Do not use aerosol spray or pump bottles as they may deposit

harmful substance on the console surface.

Over time, the console surface may collect dust or finger prints. The use of harsh chemicals will

destroy the protective coating and cause a static build up that will damage the components. This

surface may be cleaned with specially prepared chemicals found in most computer supply stores.

It is strongly recommended that you purchase such a cleaning compound.

11

AEROPRO

CONSOLE OPERATION

The console comes with 6 buttons: R (Recovery test), M (Mode), (Up or Increase), (Reset),

(Start/Stop), (Down or Decrease).

Button Functions

MODE

:

In idle mode, pressing Mode button will enter program selection.

In program, Mode button is used to confirm the selection or switch the display

UP/DOWN Scrolls

:

Scroll through programs before the workout or change resistance level during the workout.

Start/Stop

:

This key is to start or to stop the exercise. If no speed signal is detected in 4 seconds, “P” is flashing

in the upper left corner. Pressing Start or pedaling above 30 rpm, all functions will resume. In idle

mode, pressing Start/Stop button to workout manually.

Recovery Test

:

At the end of the exercise, pressing this button to test the fitness level. For a valid reading, user

must maintain pulse input during the 60 second recovery countdown test.

RESET

:

Pressing Reset button will revert to the previous display. Pressing and holding for 2 seconds will

reset all functions.

Operations

Start pedaling above 30 rpm, the console will power on and flashes all elements of the LCD

momentarily.

Auto power On/Off: if there is no activity or no speed signal detected for 90 seconds, the console

automatically turns off

Programming Functions

In programming mode, a selection of MANUAL, PROGRAM, USER, H.R.C is flashing.

Use to highlight the desired program press MODE to select

Manual Mode:

At anytime, press Start/Stop to begin exercising without entering any information. Resistance can

be changed during the workout. Alternately, press Mode to set goal (Time, Distance, Calories, and

Pulse). The parameters to be set will be flashing. Press keys to set value then press

MODE to accept. Press Start to begin the exercise.

12

AEROPRO

13

CONSOLE OPERATION (cont’d)

WATT Dependent Mode

This is available in Manual Mode only. This could also be viewed as Speed dependent mode. The

resistance level will automatically adjust to match the preset WATTS value taking speed into account.

If speed is too slow, resistance would increase to maintain the WATTS value and vice versa.

ProgramP1–P12:

These are the pre-program profiles. To exercise using a program, press the Up/Down arrows to

highlight P1 - P12 on the console. As you scroll through the programs, the program number (P1, P2,

etc.) is displayed for 1 second and a profile of the program will follow. To select, stop at a program

(profile) and press MODE (to cancel or go back, press RESET once). TIME, DISTANCE, CALORIES

& HEART RATE are available for setting. Use keys to set value and press MODE to accept.

When finished, press Start to begin the workout. Once the program started, the first segment of the

profile will blink. Resistance level can be adjusted and this adjustment will affect the entire profile.

User:

This is a user designed workout. There are 16 segments to be designed for different levels or they

all could be left at the default level (lowest). To design User program, press the Up/Down arrows to

highlight USER on the console. Press Mode to enter programming mode and immediately 1

st

segment of the profile is blinking waiting for changes. Use to change the level of the blinking

segment. Move to the next segment by pressing Mode. When finished, press Start/Stop to begin

the program.

H.R.C.

H.R.C. program is short for Heart Rate Controlled program. As suggested, the exercise is mainly

driven by the instantaneous heart rate measured from the user by the machine. There are 4 heart

rate programs available under this mode: 55%, 75%, 90% and THR. Information such as: Age, Time,

Distance & Calories must be entered before the start of the exercise. Use to scroll through

the selection. The target heart rate will be displayed for each preset program. Press MODE to

select a program. In THR program, user has the option to preset the heart rate value. User must

wear a wireless heart rate belt for this program to work. When finished, press Start/Stop to begin the

exercise.

AEROPRO

14

CONSOLE OPERATION (cont’d)

Recovery

This function evaluates the user fitness level by measuring how quickly the heart rate recovers within 1

minute. At the end of the workout, pressing Recovery will initiate this function. User must wear a

chest strap to provide heart rate to the console for evaluation. The timer starts from 60 seconds. As

soon as the timer expired, a grade is displayed from F1 to F6.

F1–Superfit

F2–Veryfit

F3–Fit

F4 - Fair

F5–Poor

F6–Verypoor

Press the Recovery key again to return to the main display.

Display Specifications

BarGraph:thereare16horizontaland8verticalelementsforatotalof128elements. Thevertical

segments represent resistance level. Each element represents 3 resistance levels. The horizontal

segments are workout time. By default, each segment lasts 1 minute.

Elapse time: ranges from 00:00 to 99:59

Speed: mph from 0.0 to 99.9

RPM: pedal crank speed from 0 to 999 revolution per minute

Distance: from 0.0 to 99.99 miles

Calories: Kilocalories from 0 to 999

Heart Rate: in beat per minute (bpm) from 0 to 240

AEROPRO

Page is loading ...

16

PART LIST

AEROPRO

NO. Q'TY Description

H930001 1SET computer

H930002 4PCS screw for fixing comput er

H930003 1PCS handlebar post

H930004 1PCS handlebar

H930005 1PCS knob f or handlebar

H930006 1PCS flat washer

H930007 1PCS handlebar post cover ( left )

H930008 1PCS handlebar post cover ( right)

H930009 1PCS end cap

H930010 4PCS screw

H930011 1PCS st opper

H930012 1PCS screw

H930013 3PCS screw

H930014 1PCS cable upper

H930015 1PCS end cap

H930016 2PCS screw

H930017 4PCS screw

H930018 1PCS batt ery box upper

H930019 1PCS battery

H930020 1PCS batt er box lower

H930021 2PCS screw

H930022 1PCS batt ery box holder

H930023 2PCS front stabilizer cap

H930024 2PCS screw

H930025 2PCS transportation wheel

H930026 2PCS flat washer

H930027 2PCS nylon nut

H930028 1SET front stabilizer

H930029 2PCS screw

H930050 1PCS pedal

H930051 1PCS screw

H930052 3PCS crank arm (left )

H930053 1PCS crank arm (right)

H930054 1PCS chaincover (left )

H930055 1PCS chaincover (right )

H930056 1SET side cover

H930057 4PCS screw

H930058 1PCS screw

H930059 1PCS screw

NO. Q'TY D escription

H930059 1PCS screw

H930060 4PCS screw

H930061 2PCS waterproof cap

H930062 2PCS cover for crank arm

H930063 2PCS nut

H930064 2PCS disc

H930065 2PCS hexagonal screw

H930066 1PCS bearing

H930067 1PCS magnet

H930068 2PCS big pulley

H930069 1PCS axle

H930070 1PCS hexagonal screw

H930071 1PCS cover left

H930072 1PCS cover right

H930073 1PCS DC hole

H930074 1PCS mainfr ame

H930075 1PCS screw

H930076 1PCS control board

H930077 1PCS cover of control board

H930078 1PCS screw

H930079 1PCS sensor box

H930080 1PCS sensor holder

H930081 1PCS screw

H930082 1PCS cap of handlebar post

H930083 1PCS Knob of handlebar post

H930084 1SET seat bushing

H930085 2PCS water bott ler holder

H930086 2PCS screw

H930087 2PCS slide knob

H930088 2PCS seat bushing

H930089 1PCS cable lower

H930090 1PCS idler axle

H930091 1PCS hexagonal screw

H930092 2PCS flat washer

H930093 2PCS idler wheel

H930094 1PCS curved washer

H930095 2PCS hexagonal screw

H930096 1SET flat washer

H930097 2PCS flat washer

17

PART LIST

AEROPRO

NO. Q'TY D escription

H930098 1PCS nylon nut

H930099 1PCS hexagonal screw

H930100 1PCS holder of spring

H930101 1PCS spring

H930112 4PCS gear box set

H930113 3PCS hexagonal screw

H930114 1PCS spring washer

H930115 2PCS flat washer

H930116 2PCS flat washer

H930117 1PCS bushing

H930118 1PCS adjust or of f lywheel

H930119 1PCS screw f or f ixing gear box

H930120 1PCS hexagonal screw

H930121 1PCS adjust ing cap

H930122 1PCS rear stabilizer

H930123 6PCS screw

H930124 2PCS saddle

H930125 2PCS cap

H930126 1PCS screw

H930127 1PCS seat slider

H930128 1PCS flat washer

H930129 8PCS knob of seat post

H930130 8PCS seat post

H930131 1PCS knob of brake

H930132 1PCS nut

H930133 1PCS fixing t ubing

H930134 1PCS spring

H930135 1PCS spring of brake

H930136 1PCS screw

H930137 1PCS bushing

H930138 6PCS U-shape socket

H930139 1PCS screw

H930140 1PCS platic bushing

H930141 3PCS bushing

H930142 2PCS nylon nut

H930143 1PCS flat washer

H930144 2PCS flat washer

H930145 1PCS pole of brake

H930146 1PCS screw

NO. Q'TY D escription

H930147 1PCS screw

H930148 1PCS holder of brake set

H930149 1PCS brake set

H930150 1PCS driving belt

H930151 1PCS screw

H930152 2PCS bushing

H930153 2PCS bearing

H930154 1PCS flywheel

H930155 1PCS bracket of tw o way bearing

H930156 1PCS flywheel axle

H930157 8PCS screw

H930158 8PCS flat washer

H930159 1PCS AC adaptor

H930160 1SET driving belt

H930161 2PCS bearing

H930162 1PCS NGP flywheel

H930163 1PCS bearing

H930164 1PCS bushing

H930165 1PCS flywheel axle

H930166 2PCS magnet of NGP syste m

H930167 4PCS holder

H930168 3PCS coil

H930169 4PCS nut

H930170 4PCS hexagonal nut

H930171 1PCS hexagonal nut

H930172 1PCS hexagonal nut

H930173 2PCS chain

H930174 2PCS bushing

H930175 1PCS idle wheel

H930176 2PCS flat washer

H930177 1PCS idler axle

H930178 1PCS flat washer

H930179 1PCS hexagonal screw

18

AEROPRO

WARRANTY

LIMITED ONE (1) YEAR PARTS AND LABOR

For ONE (1) YEAR from date of purchase, by original consumer purchaser, BH North America will

repair or replace, at its option, free of charge parts and /or labor which are defective as a result of

material or workmanship with the exception of any cosmetic component which will be covered for

NINETY (90) days from the date of purchase. Any component that is a customer point of assembly

will only be replaced; labor is not covered.

LIFETIME: FRAME

BH Fitness warrants the Frame against defects in workmanship and materials for lifetime from the

date of original purchase, so long as it remains in the possession of the original owner.

COMMERCIAL OR RENTAL USE

If a Bladez product is used for commercial or rental purposes the warranty is void.

THIS WARRANTY DOES NOT COVER

· Pre-delivery set-up

· Components that require replacement due to dirt or lack of regular maintenance

· Expendable items which become worn during normal use.

· Repairs necessary because of operator abuse or negligence or the failure to operate and

maintain the equipment according to the instructions contained in the Owner’s Manual.

BH North America Corporation

20155 Ellipse

Foothill Ranch, CA 92610

Phone: 949-206-0330; Toll Free: 866-325-2339; Fax: 949-206-0013

Email: fitness@bhnorthamerica.com

Web: www.bhnorthamerica.com

Mon - Fri 8am - 5pm PST

This warranty applies only while this product is in use in Canada.

This warranty is in addition to any statutory warranty and does not exclude or limit legal rights you

may have but shall run concurrently with applicable provincial legislation. Furthermore, some

provinces do NOT allow limitation on how long an implied warranty will last so the above limitations

may not apply.

FOR WARRANTY REPAIRS, PLEASE DO NO T TAKE

YOUR M ACHINE BACK TO TH E RETAIL STORES.

CONT ACT BLADEZ FIT NESS FIR ST!

AEROPRO H930

GUIDE DE L'UTILISATEUR

IMPORTANT:

Veuillez lire les directives attentivement avant d'utiliser le produit.

Conservez le guide pour le consulter plus tard

Tel.: 949 206-0330 Fax.: 949 206-0013 www.bhnorthamerica.com

BH North America Foothill Ranch , California 92610

Page is loading ...

BLADEZ AEROPRO H930 Owner's manual

BLADEZ AEROPRO H930 Owner's manual

in other languages

Related papers

Other documents