Carel supernode Operating instructions

Brand: Carel

Model: supernode

Type: Operating instructions

Integrated Control Solutions & Energy Savings

supernode

Electronic controller for humidication

Technical Leaet

Symbol:

Warning: The symbol in the plastic cover of the control means to refer to this technical leaet during the electrical installation.

ENG

+08U003325 Supernode for humidication - 1.0 - 14.05.2015

1. INTRODUCTION

The gateway can connect up to a maximum of 20 devices (humiSteam X-plus, heaterSteam,

gaSteam), allowing up to 150 variables (50 analogue, 50 integer, 50 digital) for each connected

device to be managed by the external supervisor.

Seven pre-set templates allow the variables exchanged between the humidier and the gateway to

be addressed automatically, depending on the device selected during programming: simply specify

the type of device and the number of devices connected. The built-in pGD on the Supernode or an

external pGD1 terminal can be used for programming.

Supernode or Kit* part number:

Description CAREL Code

Supernode for humidication + FLSTDmUGWS (controller only) SNU0000EM0

Kit Supernode HUM BACNET MSTP SNS0000EM0 +SNSCON00M0 +PCO10B0BA0

+CVSTDUMOR0 +FLSTDMUGWS

A-KSNU0CLBA11

Kit Supernode HUM BACNET ETHERNET WEB SNS0000EM0 +SNSCON00M0 +PCO10B0WB0

+FLSTDMUGWS

A-KSNU0CLWB11

Kit Supernode HUM MODBUS SNS0000EM0 +SNSCON00M0 +PCOS004850 +FLSTDMUGWS A-KSNU0CL4811

* Note: The Supernode Communication kits contain the controller, the connectors, and the

appropriate communications card. The kit also contains a USB-Flash drive with the product manuals,

technical leaets, device guides, and the Supernode variable to unit address mapping list.

On the external supervisor side, the protocol can be selected by choosing the corresponding

optional serial card. The possible options are:

Item P/N Description

1 Modbus®/CAREL RS485 PCOS0004850 Opto-isolated RS485 serial

3 BACnet™ Ethernet™ PCO10B0WB0 Ethernet™ 8 MB serial

4 BACnet™ RS485 PCO10B0BA0 BACnet™ MS/TP 485 serial

tab. 1a

The module is DIN rail mounted, with 24 Vac power supply (+10%, -15%).

Supernode for humidication allows the possibility to select UR, UEX, and UG humidiers, including

a combination of dierent models.

For the address settings of the variables on the supervisor side, refer to the dynamic table

(included on the USB drive) the “FLSTDmUGWS_Supervisory_List_dinamic_table_supernode_for_

humidication” Excel le.

The application on Supernode also features the following options:

• Edit the humidier model, if necessary add/re-address the pre-set variables.

• Manage a generic device using the “Universal” model, which can be freely edited according to

customer requirements.

ENG

+08U003325 Supernode for humidication - 1.0 - 20.06.2015

1 5 2

3 4

J10J9J8J5

+5Vref

+VDC

ID1

GND

NC1

NO1

SYNC

GND

serial card 2

serial card 1

TLAN

GND

NO2

GND

C622P028/R2

GNX

ISOLATED

Tx/Rx

PWM 0/10V

GNDTx/Rx

24 V (+10/-15%); 50/60 Hz

48 V (36Vmin…72 Vmax)

input voltage: max. power:

8 VA / 6 W

Key

1 power connector (G+,G0) 24 Vac or 36 V min...72 V max

2 SPDT relay digital output

3 pLAN network connector

4 optically-isolated “Field-Bus” serial connector

5 connector for BMS serial cards

2. INSTALLATION

Install and mount the controller in a location that is appropriate for an industrial PLC.

Mechanical fastening

The Supernode is installed on a DIN rail. To fasten the unit to the DIN rail, press it lightly against the

rail. The rear tabs will click into place, locking the unit to the rail. Removing the unit is just as simple,

using a screwdriver through the release slot to lever and lift the tabs. The tabs are kept in the locked

position by springs.

Below is a description of the connectors used for connection and installation of Supernode:

2.1 Connectors

ENG

+08U003325 Supernode for humidication - 1.0 - 14.05.2015

2.2 Connection diagram

Note: See each specic product/component technical leaet for specic wiring connections.

serial card 1

serial card 2

status RS485

GNX RS485+ –

P1 P2 P3

BACnet

™

MS/TP

RS485

CAREL master

GND

RS485

CAREL slave

GND

device 1

device 2

device n

(n<=20)

GND

PCOS004850

RS485 serial card

PCO1000BA0

BACnet™ MSTP RS485

interface

PCO1000WB0

-Ethernet™/BACnet™

interface card

ENG

+08U003325 Supernode for humidication - 1.0 - 20.06.2015

3. PROGRAMMING AND CONFIGURING THE DEVICES

Navigation of the Display Masks

Use the “Alarm”, “Program”, “Esc”, “Down/Up”, and “Enter” keys.

Note: depending on the model of Supernode, the buttons may dier as indicated here below. In

typcial control mode, the button icons are displayed on the masks in the controller software.

clear

PRG ESC











Alarm

Program

Escape

Down

Enter

3.1 Programming the Supernode

Use Password: 1234 for entering the Service or Manufacturer menu.

1. Set the number of devices connected to the gateway:

Values available: from 1 to 20 devices.

Menu path: Service  Service Settings  Device settings

2. Set the address and type of device :

Models available: heaterSteam, humiSteam X-plus, gaSteam,

generic device

Menu path: Service  Service Settings  Device settings

The address setting and type of model must be selected for

each device connected to the gateway.

ENG

+08U003325 Supernode for humidication - 1.0 - 14.05.2015

3. Set the BMS1 and BMS2 serial port for reading by

external supervisor:

Address, protocol and baud rate setting.

Menu path: Service  BMS Cong.

4. Set the Carel master protocol for communication

between Supernode and devices:

Supernode communication protocol setting with devices:

baud rate (Retry n. and ORT can be left as default)

Note: the baud rate to be set always corresponds to the

slowest device connected (for heaterSteam the baud rate

is 9600).

Menu path: Manufacturer  Factory Settings

5. Edit the model:

The selected model can be edited

Menu path: Manufacturer  Devices cong 1-10

6. Alarm settings:

Enable alarms in the event of supervisor oine

Menu path: Manufacturer  Factory Settings

ENG

+08U003325 Supernode for humidication - 1.0 - 20.06.2015

3.2 Conguring the Communications Card

Each type of protocol card has dierent tools and procedures needed to setup the card.

In general, the pCOnet and pCOWeb cards need; device instance (BACnet ID), Baud Rate, The MS/TP

station address (MAC Address), and Max Master and Max frames. These settings can be congured

in 2 ways; Using BACset, or by directly in the Supernode controller screens/masks;

• Using BACset on a computer and USB/485 Converter (see guides on using MS-TP startup and

pCOnet/web cards).

• Using the pGD display on the Supernode controller (see guide on BACnet BIOS menu).

On the PGD; hold alarm & enter: other informationPCOWEB/NET CONFIGPCONET

DHCP:---

IP ADDRESS:

---.---.---.---

3.3 Conguring the humidier unit

Please reference each specic humidier product manual for supervisory control setup. For reading

of the humidier, most units will not need any settings changed. For both reading/writing (control

the humidier by BMS), each unit will need some settings changed. In general, each humidier will

have a setting for the control type and supervisory system:

• Type of control; on/o, slave-proportional, stand-alone %RH control, etc.

• Enable the humidier to be controlled by supervisory system (on/o enable, and control

regulation by BMS).

ENG

+08U003325 Supernode for humidication - 1.0 - 14.05.2015

4. COMMUNICATING TO THE HUMIDIFIER(S)

The Supernode for humidication allows the possibility to select UR, UEX, and UG humidiers,

including a combination of dierent models.

For the address settings of the variables on the supervisor side, refer to the dynamic table (included

in the USB Drive) “FLSTDmUGWS_Supervisory_List_dinamic_table_supernode_for_humidication”

Excel le. The table includes the variable list table for heaterSteam, humiSteamx-Plug, gaSteam,

and a generic device on separate tabs.

Note: When more than (1) device is in the system, use the appropriate device tab, and device

number at the top to generate the correct variable addresses.

This table can be used also for generating the variable for more than 1 device (device 2-20).

ENG

+08U003325 Supernode for humidication - 1.0 - 20.06.2015

Note:

ENG

+08U003325 Supernode for humidication - 1.0 - 14.05.2015

Note:

CAREL INDUSTRIES HQs

Via dell’Industria, 11 - 35020 Brugine - Padova (Italy)

Tel. (+39) 049.9716611 - Fax (+39) 049.9716600

e-mail: [email protected] - www.carel.com

CAREL USA

385 South Oak Street Manheim, PA 17545

Tel. (717) 664-0500 - Fax (717) 664-0449

e-mail: [email protected] - www.carel.com

Agenzia / Agency:

+08U003325 Supernode for humidication - 1.0 - 14.05.2015

Carel supernode Operating instructions

Carel supernode Operating instructions

Carel supernode Operating instructions

Related papers

Other documents