Product manual
Articulated robot
IRB 6600 - 225/2.55 type B
IRB 6600 - 175/2.8 type B
IRB 6650 - 200/2.75 type B
IRB 6650 - 125/3.2 type B
IRB 6600ID - 185/2.55
IRB 6650ID - 170/2.75
M2000, M2000A, M2004
© Copyright 2004-2008 ABB. All rights reserved.
Product manual
IRB 6600 - 225/2.55 type B
IRB 6600 - 175/2.8 type B
IRB 6650 - 200/2.75 type B
IRB 6650 - 125/3.2 type B
IRB 6600ID - 185/2.55
IRB 6650ID - 170/2.75
M2000
M2000A
M2004
Document ID: 3HAC023082-001
Revision: E
The information in this manual is subject to change without notice and should not be
construed as a commitment by ABB. ABB assumes no responsibility for any errors that
may appear in this manual.
Except as may be expressly stated anywhere in this manual, nothing herein shall be
construed as any kind of guarantee or warranty by ABB for losses, damages to persons
or property, fitness for a specific purpose or the like.
In no event shall ABB be liable for incidental or consequential damages arising from
use of this manual and products described herein.
This manual and parts thereof must not be reproduced or copied without ABB's written
permission, and contents thereof must not be imparted to a third party nor be used for
any unauthorized purpose. Contravention will be prosecuted.
Additional copies of this manual may be obtained from ABB at its then current charge.
© Copyright 2004-2008 ABB All right reserved.
ABB AB
Robotics Products
SE-721 68 Västerås
Sweden
Table of Contents
33HAC023082-001 Revision: E
© Copyright 2004-2008 ABB. All rights reserved.
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Product documentation, M2000/M2000A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Product documentation, M2004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
How to read the product manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1 Safety 17
1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1.2 General safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1.2.1 Safety in the robot system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1.2.2 Safety risks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1.2.2.1 Safety risks during installation and service work on robot. . . . . . . . . . . . . . . . . . . . . . . . 19
1.2.2.2 Safety risks related to tools/workpieces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1.2.2.3 Safety risks related to pneumatic/hydraulic systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
1.2.2.4 Safety risks during operational disturbances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.2.2.5 Risks associated with live electric parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.2.3 Safety actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.2.3.1 Safety fence dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.2.3.2 Fire extinguishing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.2.3.3 Emergency release of the robot’s arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
1.2.3.4 Brake testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1.2.3.5 Risk of disabling function "Reduced speed 250 mm/s" . . . . . . . . . . . . . . . . . . . . . . . . . . 30
1.2.3.6 Safe use of the FlexPendant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
1.2.3.7 Work inside the manipulator's working range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1.2.3.8 Signal lamp (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
1.2.3.9 Translate the information on safety and information labels . . . . . . . . . . . . . . . . . . . . . . . 34
1.3 Safety related instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
1.3.1 Safety signals, general . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
1.3.2 DANGER - Moving manipulators are potentially lethal! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
1.3.3 DANGER - First test run may cause injury or damage! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
1.3.4 WARNING - The brake release buttons may be jammed after service work . . . . . . . . . . . . . . . . 39
1.3.5 WARNING - The unit is sensitive to ESD! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
1.3.6 WARNING - Safety risks during work with gearbox oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2 Installation and commissioning 43
2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
2.2 Robot transportation precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
2.3 Securing the robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
2.4 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
2.4.1 Pre-installation procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
2.4.2 Working range and type of motion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
2.4.3 Risk of tipping / stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
2.5 On-site installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
2.5.1 Lifting robot with fork lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
2.5.2 Lifting robot with roundslings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
2.5.3 Lifting robot with lifting slings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
2.5.4 Manually releasing the brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
2.5.5 Lifting the base plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
2.5.6 Securing the base plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
2.5.7 Orienting and securing the robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
2.5.8 Fitting equipment on robot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
2.5.9 Installation of chip and dust protection (option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
2.5.10 Installation of base spacers (option). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
2.5.11 Installation of cooling fan for motors, axes 1-3 (option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
2.5.12 Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Table of Contents
4 3HAC023082-001 Revision: E
© Copyright 2004-2008 ABB. All rights reserved.
2.6 Restricting the working range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
2.6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
2.6.2 Mechanically restricting the working range of axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
2.6.3 Mechanically restricting the working range of axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
2.6.4 Mechanically restricting the working range of axis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
2.6.5 Installation of position switches (option). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
2.7 Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
2.7.1 Robot cabling and connection points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
2.8 Making robot ready for operation (Foundry Prime). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
2.8.1 Additional installation procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
3 Maintenance 129
3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
3.2 Maintenance schedule and expected component life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
3.2.1 Specification of maintenance intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
3.2.2 Maintenance schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
3.2.3 Expected component life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
3.3 Inspection activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
3.3.1 Inspection, oil level gearbox axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
3.3.2 Inspection, oil level gearbox axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
3.3.3 Inspection, oil level gearbox axis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
3.3.4 Inspection, oil level gearbox axis 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
3.3.5 Inspection, oil level, gearbox axis 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
3.3.6 Inspection, oil level gearbox axis 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
3.3.7 Inspection, balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
3.3.8 Inspection, cable harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
3.3.9 Inspection, information labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
3.3.10 Inspection, mechanical stop, axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
3.3.11 Inspection, additional mechanical stops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
3.3.12 Inspection, damper axes 2-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
3.3.13 Inspection, position switch axes 1, 2 and 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
3.3.14 Inspection, signal lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
3.3.15 Inspection of air hoses (Foundry Prime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
3.4 Replacement/changing activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
3.4.1 Type of oil in gearboxes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
3.4.2 Oil change, gearbox axis 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
3.4.3 Oil change, gearbox axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
3.4.4 Oil change, gearbox, axis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
3.4.5 Oil change, gearbox, axis 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
3.4.6 Oil change, gearbox, axis 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
3.4.7 Oil change, gearbox axis 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
3.4.8 Replacement of SMB battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
3.5 Lubrication activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
3.5.1 Lubrication of spherical roller bearing, balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
3.5.2 Rust preventive, bearing axis 1 (Foundry Prime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
3.5.3 Rust preventive, bearing axis 4 (Foundry Prime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
3.5.4 Rust preventive, support bearing in wrist (Foundry Prime). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
3.6 Cleaning activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
3.6.1 Cleaning, robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
3.7 Service Information System, M2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
3.7.1 Using the SIS system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
3.7.2 Description of Service Information System (SIS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
3.7.3 SIS system parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Table of Contents
53HAC023082-001 Revision: E
© Copyright 2004-2008 ABB. All rights reserved.
3.7.4 Setting the SIS parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
3.7.5 Reading the SIS output logs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
3.7.6 Exporting the SIS data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
4 Repair 223
4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
4.2 General procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
4.2.1 Performing a leak-down test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
4.2.2 Mounting instructions for bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
4.2.3 Mounting instructions for seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
4.3 Complete robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
4.3.1 Replacement of cable harness, axes 1-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
4.3.2 Replacement of cable harness, axes 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
4.3.3 Replacement of cable harness, axes 5-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
4.3.4 Replacement of cable harness, axes 5-6, IRB 6600ID and IRB 6650ID . . . . . . . . . . . . . . . . . . . 253
4.3.5 Replacement of cabling, axis 5 motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
4.3.6 Replacement of complete arm system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
4.3.7 Replacement of air nipple and hose (Foundry Prime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
4.4 Upper and lower arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
4.4.1 Replacement of turning disk, IRB 6600 and IRB 6650 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
4.4.2 Replacement of complete wrist unit, IRB 6600 and IRB 6650 . . . . . . . . . . . . . . . . . . . . . . . . . . 277
4.4.3 Replacement of complete wrist unit, IRB 6600ID and IRB 6650ID . . . . . . . . . . . . . . . . . . . . . . 282
4.4.4 Replacement of upper arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
4.4.5 Replacement of complete lower arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
4.4.6 Replacement of lower arm shaft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
4.4.7 Securing the lower arm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
4.5 Frame and base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
4.5.1 Replacement of SMB unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
4.5.2 Replacement of brake release unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
4.5.3 Replacement of spherical roller bearing, balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
4.5.4 Replacement of balancing device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
4.5.5 Unloading the balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
4.5.6 Restoring the balancing device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334
4.6 Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337
4.6.1 Replacement of motor, axis 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337
4.6.2 Replacement of motor axis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343
4.6.3 Replacement of motor, axis 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
4.6.4 Replacement of motor, axis 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
4.6.5 Replacement of motor, axis 5, IRB 6600 and IRB 6650 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364
4.6.6 Replacement of motor, axis 5, IRB 6600ID and IRB 6650ID . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
4.6.7 Replacement of motor, axis 6, IRB 6600 and IRB 6650 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374
4.6.8 Replacement of motor, axis 6, IRB 6600ID and IRB 6650ID . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
4.7 Gearboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
4.7.1 Replacement of gearbox, axis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
4.7.2 Replacement of gearbox axis 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
4.7.3 Replacement of gearbox, axis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
4.7.4 Replacement of gearbox, axis 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405
5 Calibration information 409
5.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409
5.2 Calibration methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
5.3 Calibration scales and correct axis position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
5.4 Calibration movement directions for all axes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414
Table of Contents
6 3HAC023082-001 Revision: E
© Copyright 2004-2008 ABB. All rights reserved.
5.5 Updating revolution counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415
5.6 Checking the calibration position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419
5.7 Additional calibration instruction, IRB4400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421
6 Decommissioning 423
6.1 Environmental information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423
6.2 Decommissioning of balancing device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424
7 Robot description 427
7.1 Type A and type B of IRB 6600/6650 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
8 Reference information 429
8.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429
8.2 Applicable Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
8.3 Unit conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431
8.4 Screw joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 432
8.5 Weight specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435
8.6 Standard toolkit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
8.7 Special tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437
8.8 Lifting equipment and lifting instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440
9 Spare part / part list 441
9.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441
9.2 Spare part list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442
9.2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442
9.2.2 Spare part list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443
9.3 Part list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448
9.3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448
9.3.2 Rebuilding parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449
9.3.3 Part list, overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451
9.3.4 Base incl frame ax 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453
9.3.5 Axis 3-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454
9.3.6 Axis 3-4, Foundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
9.3.7 Axis 3-4 Foundry Prime. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459
9.3.8 Wrist, type 2, standard, IRB 6600 and IRB 6650 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460
9.3.9 Wrist, process, IRB 6600ID and 6650ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
9.3.10 Wrist, type 2, Foundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466
9.3.11 Wrist, type 2, insulated. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467
9.3.12 Wrist, type 2, Foundry Prime. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 468
9.3.13 Material set, manipulator, 3HAC 13263-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 469
9.3.14 Material set, axis 1-2, 3HAC 13264-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470
9.3.15 Material set, balancing device, 3HAC 13265-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
9.3.16 Arm extension set, 250 mm, 3HAC 12311-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474
9.3.17 Arm extension set, 450 mm, 3HAC 12311-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475
10 Exploded views 477
10.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477
10.2 Base incl. Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 478
10.3 Frame-Lower arm 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 479
10.4 Frame-Lower arm 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480
10.5 Upper arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 481
10.6 Wrist complete, IRB 6600 and IRB 6650 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482
10.7 Wrist complete, IRB 6600ID and IRB 6650ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483
Table of Contents
73HAC023082-001 Revision: E
© Copyright 2004-2008 ABB. All rights reserved.
11 Circuit Diagram 485
11.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485
11.2 Circuit diagram 3HAC 025744-001. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486
11.2.1 Validity of circuit diagram 3HAC 025744-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486
11.3 Circuit diagram 3HAC 13347-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 487
11.3.1 Validity of circuit diagram 3HAC 13347-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 487
Index 489
Table of Contents
8 3HAC023082-001 Revision: E
© Copyright 2004-2008 ABB. All rights reserved.
Overview
93HAC023082-001 Revision: E
© Copyright 2004-2008 ABB. All rights reserved.
Overview
About this manual
This manual contains instructions for
• mechanical and electrical installation of the robot
• maintenance of the robot
• mechanical and electrical repair of the robot.
Usage
This manual should be used during
• installation, from lifting the robot to its work site and securing it to the foundation, to
making it ready for operation
• maintenance work
• repair work
Who should read this manual?
This manual is intended for:
• installation personnel
• maintenance personnel
• repair personnel.
Prerequisites
A maintenance/repair/ installation craftsman working with an ABB Robot must:
• be trained by ABB and have the required knowledge of mechanical and electrical
installation/repair/maintenance work.
Organization of chapters
The manual is organized in the following chapters:
Chapter Contents
Safety Safety information that must be read through before performing
any installation or service work on robot. Contains general safety
aspects as well as more specific information about how to avoid
personal injuries and damage to the product.
Installation and commis-
sioning
Required information about lifting and installation of the robot.
Maintenance Step-by-step procedures that describe how to perform
maintenance of the robot. Based on a maintenance schedule
that may be used in the work of planning periodical maintenance.
Repair Step-by-step procedures that describe how to perform repair
activities of the robot. Based on available spare parts.
Calibration Information Procedures that does not require specific calibration equipment.
Decommissioning Environmental information about the robot and its components.
Continues on next page
Overview
3HAC023082-001 Revision: E10
© Copyright 2004-2008 ABB. All rights reserved.
References
Following documents are referred to throughout the manual:
Document name Document ID Note
Product specification - IRB 6600/6650/6650S
M2004
3HAC023933-001 M2004
Product specification - IRB 6600/6650/6650S
M2000/M2000A
3HAC14064-1 M2000/M2000A
Product manual - IRC5 3HAC021313-001
Product manual - S4Cplus M2000 3HAC021333-001
Product manual - S4Cplus M2000A 3HAC022419-001
Operating manual - IRC5 with FlexPendant 3HAC16590-1
Operating manual - Calibration Pendulum 3HAC16578-1
Operating manual - Levelmeter Calibration 3HAC022907-001
User’s guide - S4Cplus 3HAC7793-1
Operating manual - Service Information
System
3HAC025709-001
Technical reference manual - System
parameters
3HAC17076-1
Application manual - Additional axes and
stand alone controller
3HAC021395-001 M2004
Application manual - External axes 3HAC9299-1 M2000/M2000A
Continued
Continues on next page
Overview
113HAC023082-001 Revision: E
© Copyright 2004-2008 ABB. All rights reserved.
Revisions
Revision Description
- First edition
A Chapter Calibration is replaced with new chapter Calibration information.
Chapter Safety, Service is replaced with new chapter Safety.
Section Document references is completed with article number for calibration
manuals.
B New lubricating oil in the gearboxes, axes 1, 2, 3 and 6. Changes are made in
chapter Maintenance and section Part list.
C New robot models, IRB 6600ID and IRB 6650ID, are implemented throughout
the manual.
Additional changes made in the manual:
• Changes made in the Part list in the Product manual, reference
information (new article numbers for items 101.2.3, 103.1.30, 109.302).
• Attachment holes in the frame moved to different location. New figure in
section Illustration, fitting of extra equipment on frame on page 84.
• New procedure for optional equipment: Installation of cooling fan for
motors, axes 1-3 (option) on page 97. Additional cabling also added to
section Robot cabling and connection points on page 122.
• Supplementary details about required cabling for position switches are
added to section Installation of position switches (option) on page 111,
together with a procedure for how to install the cabling.
• A complete (undivided) cabling from axis 1 to axis 6 is added to the spare
parts in Spare part list on page 443. New procedure: Replacement of
cable harness, axes 1-6 on page 228. Also a new circuit diagram is
added to the manual, due to the new cabling.
• New procedure: Replacement of spherical roller bearing, balancing
device on page 317 due to added spare parts in Spare part list on page
443.
• The section about SIS (Service Information System) is now only valid for
M2000 robot systems. For information regarding SIS for M2004
systems, see additional manual about SIS. Art. no. for the manual is
specified in section References on page 10.
D • Information about document references are moved to the table
References on page 10.
• Foundry Prime Option included.
E Changes made in:
• Prerequisites in section Overview
• Oil change in section Maintenance
• New section Robot transportation precautions.
• New section Securing the robot
Continued
Product documentation, M2000/M2000A
3HAC023082-001 Revision: E12
© Copyright 2004-2008 ABB. All rights reserved.
Product documentation, M2000/M2000A
General
The complete product documentation kit for the M2000 robot system, including controller,
robot and any hardware option, consists of the manuals listed below:
Product manuals
All hardware, robots and controllers, will be delivered with a Product manual which is
divided into two parts:
Product manual, procedures
• Safety information
• Installation and commissioning (descriptions of mechanical installation, electrical
connections)
• Maintenance (descriptions of all required preventive maintenance procedures
including intervals)
• Repair (descriptions of all recommended repair procedures including spare parts)
• Additional procedures, if any (calibration, decommissioning)
Product manual, reference information
• Reference information (article numbers for documentation referred to in Product
manual, procedures, lists of tools, safety standards)
• Part list
• Foldouts or exploded views
• Circuit diagrams
The product manual published as a PDF consists of only one file where the two parts are
presented together, as one Product manual.
Software manuals
The software documentation consists of a wide range of manuals, ranging from manuals for
basic understanding of the operating system to manuals for entering parameters during
operation.
A complete listing of all available software manuals is available from ABB.
Controller hardware option manual
Each hardware option for the controller is supplied with its own documentation. Each
document set contains the types of information specified below:
• Installation information
• Repair information
• Maintenance information
In addition, spare part information is supplied for the entire option.
Product documentation, M2004
133HAC023082-001 Revision: E
© Copyright 2004-2008 ABB. All rights reserved.
Product documentation, M2004
General
The robot documentation may be divided into a number of categories. This listing is based on
the type of information contained within the documents, regardless of whether the products
are standard or optional. This means that any given delivery of robot products will not contain
all documents listed, only the ones pertaining to the equipment delivered.
However, all documents listed may be ordered from ABB. The documents listed are valid for
M2004 robot systems.
Product manuals
All hardware, robots and controllers, will be delivered with a Product manual which is
divided into two parts:
Product manual, procedures
• Safety information
• Installation and commissioning (descriptions of mechanical installation, electrical
connections)
• Maintenance (descriptions of all required preventive maintenance procedures
including intervals)
• Repair (descriptions of all recommended repair procedures including spare parts)
• Additional procedures, if any (calibration, decommissioning)
Product manual, reference information
• Reference information (article numbers for documentation referred to in Product
manual, procedures, lists of tools, safety standards)
• Part list
• Foldouts or exploded views
• Circuit diagrams
The product manual published as a PDF consists of only one file where the two parts are
presented together, as one Product manual.
Technical reference manuals
The following manuals describe the robot software in general and contain relevant reference
information:
• RAPID Overview: An overview of the RAPID programming language.
• RAPID Instructions, Functions and Data types: Description and syntax for all
RAPID instructions, functions and data types.
• System parameters: Description of system parameters and configuration workflows.
Continues on next page
Product documentation, M2004
3HAC023082-001 Revision: E14
© Copyright 2004-2008 ABB. All rights reserved.
Application manuals
Specific applications (e.g. software or hardware options) are described in Application
manuals. An application manual can describe one or several applications.
An application manual generally contains information about:
• The purpose of the application (what it does and when it is useful)
• What is included (e.g. cables, I/O boards, RAPID instructions, system parameters, CD
with PC software)
• How to use the application
• Examples of how to use the application
Operating manuals
This group of manuals is aimed at those having first hand operational contact with the robot,
i.e. production cell operators, programmers and trouble shooters. The group of manuals
includes:
• Getting started - IRC5 and RobotStudio
• IRC5 with FlexPendant
• RobotStudio
• Trouble shooting - IRC5 for the controller and robot
Continued
How to read the product manual
153HAC023082-001 Revision: E
© Copyright 2004-2008 ABB. All rights reserved.
How to read the product manual
Reading the procedures
The procedures contain references to figures, tools, material etc. The references are read as
described below.
References to figures
The procedures often include references to components or attachment points located on the
robot/controller. The components or attachment points are marked with italic text in the
procedures and completed with a reference to the figure where the current component or
attachment point is shown.
The denomination in the procedure for the component or attachment point corresponds to the
denomination in the referenced figure.
The table below shows an example of a reference to a figure from a step in a procedure.
References to required equipment
The procedures often include references to equipment (spare parts, tools etc.) required for the
different actions in the procedure. The equipment is marked with italic text in the procedures
and completed with a reference to the section where the equipment is listed with further
information, i.e. article number, dimension.
The denomination in the procedure for the component or attachment point corresponds to the
denomination in the referenced list.
The table below shows an example of a reference to a list of required equipment, from a step
in a procedure.
Safety information
The manual includes a separate safety chapter that must be read through before proceeding
with any service or installation procedures. All procedures also include specific safety
information when dangerous steps are to be performed.
Read more in chapter Safety on page 17.
Action Note/Illustration
8. Remove the rear attachment screws, gearbox. Shown in the figure Location of
gearbox on page xx.
Action Note/Illustration
3. Fit a new sealing, axis 2 to the gearbox. Art. no. is specified in Required
equipment on page xx.
How to read the product manual
3HAC023082-001 Revision: E16
© Copyright 2004-2008 ABB. All rights reserved.
1 Safety
1.1. Introduction
173HAC023082-001 Revision: E
© Copyright 2004-2008 ABB. All rights reserved.
1 Safety
1.1. Introduction
Overview
The safety information in this manual is divided in two categories:
• general safety aspects, important to attend to before performing any service work on
the robot. These are applicable for all service work and are found in section General
safety information on page 18.
• specific safety information, pointed out in the procedure at the moment of the danger.
How to avoid and eliminate the danger is either detailed directly in the procedure, or
further detailed in separate instructions, found in section Safety related instructions on
page 35.
1 Safety
1.2.1. Safety in the robot system
3HAC023082-001 Revision: E18
© Copyright 2004-2008 ABB. All rights reserved.
1.2 General safety information
1.2.1. Safety in the robot system
Validity and responsibility
The information does not cover how to design, install and operate a complete system, nor
does it cover all peripheral equipment, which can influence the safety of the total system. To
protect personnel, the complete system must be designed and installed in accordance with the
safety requirements set forth in the standards and regulations of the country where the robot
is installed.
The users of ABB industrial robots are responsible for ensuring that the applicable safety laws
and regulations in the country concerned are observed and that the safety devices necessary
to protect people working with the robot system are designed and installed correctly.
Personnel working with robots must be familiar with the operation and handling of the
industrial robot, described in the applicable documents, e.g.
• User’s Guide - S4Cplus (M2000)
• Operating Manual - IRC5 with FlexPendant (M2004)
• Product Manual
Connection of external safety devices
Apart from the built-in safety functions, the robot is also supplied with an interface for the
connection of external safety devices. Via this interface, an external safety function can
interact with other machines and peripheral equipment. This means that control signals can
act on safety signals received from the peripheral equipment as well as from the robot.
Limitation of liability
Any information given in this manual regarding safety, must not be construed as a warranty
by ABB that the industrial robot will not cause injury or damage even if all safety instructions
are complied with.
Related information
Type of information Detailed in document Section
Installation of safety
devices
Product manual for the robot Installation and commissioning
Changing operating
modes
User’s guide - S4Cplus
(RobotWare 4.0)
Operating manual - IRC5 with
FlexPendant (RobotWare 5.0)
Start-up
Operating modes
Restricting the working
space
Product manual for the robot Installation and commissioning
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416
  • Page 417 417
  • Page 418 418
  • Page 419 419
  • Page 420 420
  • Page 421 421
  • Page 422 422
  • Page 423 423
  • Page 424 424
  • Page 425 425
  • Page 426 426
  • Page 427 427
  • Page 428 428
  • Page 429 429
  • Page 430 430
  • Page 431 431
  • Page 432 432
  • Page 433 433
  • Page 434 434
  • Page 435 435
  • Page 436 436
  • Page 437 437
  • Page 438 438
  • Page 439 439
  • Page 440 440
  • Page 441 441
  • Page 442 442
  • Page 443 443
  • Page 444 444
  • Page 445 445
  • Page 446 446
  • Page 447 447
  • Page 448 448
  • Page 449 449
  • Page 450 450
  • Page 451 451
  • Page 452 452
  • Page 453 453
  • Page 454 454
  • Page 455 455
  • Page 456 456
  • Page 457 457
  • Page 458 458
  • Page 459 459
  • Page 460 460
  • Page 461 461
  • Page 462 462
  • Page 463 463
  • Page 464 464
  • Page 465 465
  • Page 466 466
  • Page 467 467
  • Page 468 468
  • Page 469 469
  • Page 470 470
  • Page 471 471
  • Page 472 472
  • Page 473 473
  • Page 474 474
  • Page 475 475
  • Page 476 476
  • Page 477 477
  • Page 478 478
  • Page 479 479
  • Page 480 480
  • Page 481 481
  • Page 482 482
  • Page 483 483
  • Page 484 484
  • Page 485 485
  • Page 486 486
  • Page 487 487
  • Page 488 488
  • Page 489 489
  • Page 490 490
  • Page 491 491
  • Page 492 492
  • Page 493 493
  • Page 494 494
  • Page 495 495
  • Page 496 496
  • Page 497 497
  • Page 498 498
  • Page 499 499
  • Page 500 500
  • Page 501 501
  • Page 502 502
  • Page 503 503
  • Page 504 504
  • Page 505 505
  • Page 506 506
  • Page 507 507
  • Page 508 508
  • Page 509 509
  • Page 510 510
  • Page 511 511
  • Page 512 512
  • Page 513 513
  • Page 514 514
  • Page 515 515
  • Page 516 516
  • Page 517 517
  • Page 518 518
  • Page 519 519
  • Page 520 520
  • Page 521 521
  • Page 522 522
  • Page 523 523
  • Page 524 524
  • Page 525 525
  • Page 526 526
  • Page 527 527
  • Page 528 528
  • Page 529 529
  • Page 530 530
  • Page 531 531
  • Page 532 532
  • Page 533 533

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI