42723-01 • 11/7/06
2
Hunter® Fan Company 42723-01 • 11/7/06
Table of Contents
1 • Getting Ready .....................................................4
2 • Assembling the Skirt .......................................5
3 • Assembling the Base .......................................6
4 • Assembling the Table .....................................8
5 • Assembling the Fan ......................................10
6 • Assembling the Light Kit ...........................11
7 • Completing Assembly .................................12
8 • Operating and Cleaning Your Fan ........13
9 • Troubleshooting .............................................14
Welcome
© 2006 Hunter Fan Company®
READ AND SAVE THESE INSTRUCTIONS.
Your new Hemingway by Hunter
®
fan is an addition to your
outdoor living environment that will provide comfort and
performance for many years. is installation and operation
manual gives you complete instructions for assembling and
operating your fan.
We are proud of our work. We appreciate the opportunity to
supply you with the best fan available anywhere in the world.
Before assembling your fan, for your records and warranty
assistance, record information from the carton and Hemingway
by Hunter® nameplate label (located on the top of the fan
motor housing) on the front cover of this manual.
For Your Records and Warranty
Assistance
Model Name: _____________________
Catalog/Model No.: ________________
Serial No.: ________________________
Date Purchased: ___________________
Where Purchased: _________________
For reference also attach your receipt or a
copy of your receipt to the manual.
3
42723-01 • 11/7/06 Hunter® Fan Company
Important Information
General & Location:
• Use ONLY Hunter® replacement parts.
• is fan is intended for outdoor use ONLY. is fan is
suitable for wet locations. If the fan has been subjected
to extreme weather conditions, inspect before use.
• is fan MUST be assembled by three or more people.
Do NOT attempt to assemble this fan without
assistance.
• Make sure the installation site you choose allows the
fan blades to rotate without any obstructions within
6 feet of end of fan blades. A minimum clearance of 7
feet from the finished surface to the bottom edge of
the fan blade is required.
• If locating under an awning or covering, we
recommend a minimum awning or covering height of
10 feet.
• is fan is NOT to be used on, or within 6 feet of stairs.
Warnings:
• To reduce the risk of personal injury, assemble the fan according
to these instructions, and use only the hardware supplied.
• To reduce the risk of personal injury, do NOT bend the blade
attachment system when installing, balancing, or cleaning the fan.
NEVER insert foreign objects between rotating fan blades.
• To avoid possible electrical shock, before relocating your fan,
disconnect the power by unplugging the power cord from the
electrical outlet.
• To reduce the risk of electrical shock, keep fan at least 16 feet away
from pools and spas. NEVER place the fan where it can fall or be
pulled into a pool or hot tub.
• To reduce the risk of electrical shock, ALWAYS connect to an
outlet provided with a Ground Fault Circuit Interrupting Device
(GFCI).
• ALWAYS keep power cord dry and out of water (puddles, pools,
fountains).
• is appliance has a grounded three-prong plug and is suitable
for grounded receptacle use only. Do NOT attempt to defeat the
purpose of this safety feature.
Cautions:
• Do NOT climb on pole or table (if applicable).
• Do NOT use an extension cord with this fan.
• Do NOT place objects on power cord.
• Do NOT operate if: a) the power cord or plug is damaged; b) the appliance malfunctions; or c) the unit has been damaged in any
manner. Contact Hunter® Fan Company’s Service Department. Do not return to the retailer.
• Do NOT operate within 6 feet of objects or walkways.
• Do NOT assemble or operate this fan on unlevel ground. is fan may ONLY be placed on level decks, level patios, level ground or
similar flat, level surfaces.
• All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70.
• Before each use, inspect the power cord for cuts, wear and/or abrasion marks. If any are found, or any wires are exposed, the
appliance should be serviced and the power cord replaced. Please contact Hunter®® Fan Company’s Service Department. Do not
return to the retailer.
Read this entire manual
carefully before beginning
installation. Save these
instructions.
4
Hunter® Fan Company 42723-01 • 11/7/06
1 • Getting Ready
To assemble this fan, be sure each person can do the following:
• Connect electrical wires.
• Lift 50 pounds.
If you need help installing the fan, your Hemingway by Hunter® fan
dealer can direct you to a licensed installer or electrician.
Gathering the Tools
You will need the following tools for assembling the fan:
• Standard screwdriver
• Phillips-head screwdriver
• Allen Wrench (included)
• 7/16” Wrench or pliers
Checking Your Fan Parts
Carefully unpack your fan to avoid damage to the fan parts. Refer
to the Parts Guide Sheet included in the carton. Check for any
shipping damage to the motor or fan blades. If any parts are missing
or damaged, contact your Hunter® dealer or call Hunter® Technical
Support Department at 888-830-1326.
Assembling Multiple Fans?
If you are assembling more than
one fan, keep the fan blades and
blade irons in sets, as they were
shipped.
ATTENTION:
is fan must be assembled by
three or more people. Do not
attempt to assemble this fan
without assistance.
is fan weighs approximately
150 lbs.
5
42723-01 • 11/7/06 Hunter® Fan Company
2 • Assembling the Skirt
Note: is fan should be assembled in an open,
level area with a solid ground surface large
enough for the assembled fan.
2-1. Locate the base stand and place it on the ground at the location
where the fan will be operated.
2-2. Identify the skirt section with the 4
small screw holes around the power
cord channel and a notch in the inner
edge. Align the four holes in the skirt
section with the holes in the base
stand where the power cord is located,
then align the notch in the skirt
section with the raised tab on the base
stand. Partially install four base bolts
to attach the skirt section to the base stand. To ensure proper
spacing, do not tighten the bolts until all have been partially
installed.
Note: e remaining three skirt sections are identical and may be
installed in any order.
2-3. Align the four holes in the next skirt section with four holes in the base
stand. Partially install four base bolts. Repeat for the remaining skirt
sections.
CAUTION: Do not attempt to assemble fan without all four skirt sections. e fan may fall if a skirt section is not installed.
Skirt
Section
Base Stand
Power Cord
Channel
Base
Bolt
4 Small Screw Holes
Base Bolt
64193-02-247
(x 16)
Hardware Needed:
Steps 2-1 - 2-3:
Skirt Bolt
Skirt
Section
Skirt Bolt
06548-01-247
(x 16)
Hardware Needed:
Step 2-4:
2-4. Align the holes in each skirt bracket with the
adjoining skirt section and partially install
two skirt bolts. Repeat for all skirt sections.
2-5. After all skirt sections are properly aligned,
securely tighten all skirt bolts and base bolts.
Skirt
Bracket
6
Hunter® Fan Company 42723-01 • 11/7/06
3 • Assembling the Base
3-1. Guide the power cord through the channel
and install the cover plate over the power cord
using four screws. Be sure the power cord is not
pinched between the channel and the cover plate.
You will need the assistance of at least one other
person to assemble the base and skirt sections.
Tab
Screw
Lower
Pole
Section
Lower
Pole
Bolt
Lower
Pole
Nut
Cover Plate
Screw
74506-59-247
(x 4)
Hardware Needed:
Hardware Needed:
Lower Pole Bolt
06551-10-247
(x 2)
Hardware Needed:
Lower Pole Nut
06552-02-247
(x 2)
3-2. read the power cord through the lower pole section
and slide the lower pole onto the base stand. Align the
holes in the lower pole segment with the holes in the
base stand and securely install two lower pole bolts
with nuts to stabilize.
3-3. Being careful to not damage the fan finish, slide the
base cover onto the lower pole and let it rest on the
base stand.
3-4. Holding both the base stand and base cover,
carefully tilt the base assembly and rest the
assembly on its side to access the bottom of the
base. Align the two tabs on the base cover with the
two holes in the base stand. Install two screws to
secure the base cover to the base stand.
Steps 3-3 - 3-4:
Tab Screw
74513-54-247
(x 2)
Hardware Needed:
Step 3-1:
Step 3-2:
Power
Cord
Cover
Plate
Screw
Channel
7
42723-01 • 11/7/06 Hunter® Fan Company
Middle
Pole
Section
Power
Cord
Base
Cover
Spindle
Spindle
Cover
Base
Stand
Grommet
3 • Assembling the Base
Step 3-7:
Pole Screw
06549-01-247
(x 3)
Hardware Needed:
3-6. Note: e spindle is optional. e fan can be installed with only the
spindle cover.
Holding the grommet in place, slide the spindle (optional) and
spindle cover onto the lower pole. Lower the spindle and spindle
cover to rest on the base cover.
Step 3-6:
3-7. read the power cord through the middle pole
section. Attach the middle pole section to the lower
pole section. Align the holes and securely install three
screws to stabilize.
3-5. With the assembly still on its side, install the
third foot into the base with the provided
screw. (e first two have been preinstalled.)
When the final foot has been installed, tilt the
assembly back to its upright position.
Step 3-5:
Foot Screw
74510-27-247
(x 1)
Hardware Needed:
Foot
Screw
Foot
Preinstalled feet
Without
Spindle
With
Spindle
8
Hunter® Fan Company 42723-01 • 11/7/06
Note: Be sure to hold the power cord out of the
way of the bolt. Do not allow the power cord to
slip down the pole.
4-1. Insert the bolt into the lower pole section and
secure with the cotter pin.
Step 4-1:
Cotter
Pin
Bolt
4 • Assembling the Table
Your new accessory Hunter table can be installed at one of three heights:
bar height
42”
standard table height
29”
lounge height
20”
If you do not wish to install the included table, skip to Section 5 to continue installation.
9
42723-01 • 11/7/06 Hunter® Fan Company
4 • Assembling the Table
4-3. Being careful not to damage the pole finish,
(with assistance from at least one other person)
place the hole in the center of the table over the
lower pole segment. Align the notch in the lower
adapter with the bolt. Rest the table on the bolt.
4-4. With the notch resting on the bolt, rotate the
table clockwise to secure it to the pole.
Step 4-2:
4-2. Attach the upper adapter to the table with
six adapter screws with washers. read the
lower adapter into the upper adapter and
rotate one to two turns.
Note: e lower adapter should not be
over-tightened. It should remain loose in
the upper adapter to properly attach to the
table.
Step 4-3 - 4-4:
Table
Lower Pole
Segment
Table
Upper
Adapter
Lower
Adapter
Hardware Needed:
Adapter Screw
64193-03-247
(x 6)
Table
Hardware Needed:
Washer
64187-01-247
(x 6)
10
Hunter® Fan Company 42723-01 • 11/7/06
5 • Assembling the Fan
Note: You may rest the fan body in the
carton for protection and stability during
this time.
5-1. Remove the blade iron screws and shipping
blocks from the fan motor. Save the screws
and discard the shipping blocks.
5-2. Align the holes in the blade with the holes in
the blade iron and attach with three blade
screws. Securely tighten the screws.
Blade
Iron
Screw
Upper
Switch
Housing
Blade Screw
74510-27-247
(x 15)
Hardware Needed:
Blade Iron
Screw
63755-06-247
(x 10)
Hardware Needed:
Upper Switch
Housing Screw
74506-54-247
(x 2)
Hardware Needed:
Steps 5-1 - 5-2:
Step 5-3:
5-3. Partially attach each blade assembly to the fan with
two blade iron screws. When all blades are attached
and properly spaced, securely tighten all screws.
5-4. Unbundle the wires from the fan. read
the wires from the fan through the hole
in the upper switch housing. Attach the
upper switch housing to the fan using two
screws.
Step 5-4:
Blade
Screw
Blade
Blade
Iron
11
42723-01 • 11/7/06 Hunter® Fan Company
Screw
Boss
Upper Pole
Segment
Upper Pole
Screw
74514-60-247
(x 4)
Hardware Needed:
Switch Housing
Screw
64555-05-247
(x 3)
Hardware Needed:
6-1. read the power cord with the 3-pin plug connector
from the fan through the upper pole segment.
6 • Assembling the Light Kit
6-2. Pull the 9-pin plug connector through the side
of the upper pole segment. Align the holes in the
upper pole segment with the bosses in the upper
switch housing. Install four screws to secure the
upper pole segment to the fan.
Step 6-1:
Step 6-2:
6-3. Being careful not to damage the fan finish,
slide the light kit onto the upper pole segment
holding the grommet in place. Connect the 9-pin
plug connector from the fan to the 9-pin plug
connector from the light kit.
6-4. Align the holes in the side of the light kit with the
holes in the upper switch housing and securely
install three switch housing screws.
Steps 6-3 - 6-4:
9-Pin
Plug
Con-
nector
Plug
Connectors
Light Kit
12
Hunter® Fan Company 42723-01 • 11/7/06
7 • Completing Assembly
Note: Be sure there are no obstructions before lifting
the fan to complete assembly.
7-1. Being careful to not pinch any wires, lift the fan and
upper pole assembly (with assistance from at least
one other person) and place it onto the middle pole
segment. Align the window in the upper pole with the
window in the middle pole.
7-2. Connect the 3-pin plug connector from the fan to the
3-pin plug connector from the base. Push the wires into
the pole.
CAUTION: Do not attempt to assemble fan without all three pole
segments.
Window
Open
Screw
Upper
Pole
Segment
Logo
Coverplate
Screw
Window
Closed
Pole Screw
06549-01-247
(x 1)
Hardware Needed:
Pole Screw
06549-01-247
(x 2)
Hardware Needed:
7-3. Be sure no wires are pinched before
closing the window. Rotate the upper pole
segment 180
o
to align the screw holes and
close the window.
7-4. Align the holes with the logo coverplate
and securely install two screws.
Steps 7-1 - 7-2:
Steps 7-3 - 7-4:
7-5. Install the remaining screw behind the logo coverplate.
Securely tighten all screws.
Step 7-5:
13
42723-01 • 11/7/06 Hunter® Fan Company
8 • Operating and Cleaning Your Fan
8-2. Install the plastic plugs into the remaining holes in the pole. If you
chose not to install the table, you will need to intall all the included
plugs.
8-3. Plug the fan into an electrical outlet.
8-4. e fan pull chain controls power to the fan.
e pull chain has four settings in sequence: High,
Medium, Low and Off.
• Pull the chain slowly to change settings.
• Release slowly to prevent the chain from
recoiling into the blades.
8-5. e light pull chain controls power to the light.
• Pull the chain slowly to change settings.
8-6. is fan operates in a downdraft direction only by blowing air
downward (counterclockwise blade rotation) to cool the area with a
direct breeze.
8-7. For cleaning finishes, use a soft brush or lint-free cloth to prevent
scratching. A vacuum cleaner brush nozzle can remove heavier dust.
Remove surface smudges or accumulated dirt and dust using a mild
detergent and a slightly dampened cloth. You may use an artistic
agent, but never abrasive cleaning agents as they will damage the
finish.
Completed Assembly
87”
Note: If you are not installing the light kit, skip step 8-1.
8-1. Insert a glass shade into a fitter and tighten the
thumbscrews. Repeat for all shades. Install three A-19
medium base 60 Watt max light bulbs.
Step 8-1:
Glass
Shade
Bulb
Note: Do not use a water hose or pressure washer to clean
this fan.
14
Hunter® Fan Company 42723-01 • 11/7/06
9 • Troubleshooting
Problem: Nothing happens; fan does not move.
1. Turn power on, replace fuse, or reset breaker.
2. Check the plug connections in the switch housing.
3. Pull the pull chain to ensure it is on.
4. Remove the shipping bumpers.
5. Ensure that the fan is plugged into a suitable GFCI outlet.
Problem: Noisy operation.
1. Tighten the blade iron screws until snug.
2. Tighten the blade screws until snug.
3. Check to see if the blade is cracked. If so, replace all the blades.
4. Check and tighten the screws in the switch housing mounting
plate and in the upper and lower switch housing.
Problem: Excessive wobbling.
1. If your fan wobbles when operating, use the enclosed balancing
kit and instructions to balance the fan.
2. Tighten all blade and/or blade iron screws.
3. Tighten all skirt and base screws.
4. Make sure all three rubber feet are installed under the base.
Problem: Table wobbling.
1. Make sure the notch in the lower adapter is rotated counterclockwise over
the bolt.
If you need parts or service assistance, please call
888-830-1326 or visit us at our Web site at
http://www.Hunterfan.com.
Hunter® Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
/
