Page is loading ...
DISINFECTION
HOSPITAL
NEX-ES
RBIT
ELECTROSTATIC DISINFECTION
SPRAYER SYSTEM
NEX-ES BP360UV
360° Coverage
UV Light Technology
Black Light
Inspection Flashlight
Black Light Inspection Flashlight
UV Light Technology
NEX-ES ORBIT
ELECTROSTATIC SPRAYER
DISINFECTION
HOSPITAL
COMMUNITY
PARK
Ceramic Chip Applicator
Dear Customer:
Thank you for choosing our the NEX-ES Orbit Electrostatic Backpack. It is the
first unique design which offers UVC Technoloy in a backpack electrostatic
sprayer. Please read the operation manual carefully before use the product,
strictly abide by the safety operation rules, in order to prevent product failure
from affecting your normal use or cause unnecessary losses.
We are committed to the constant optimization and improvement of our
product design. We will appreciate for your valuable suggestions or feedback.
BROADBAND
INNOVATION
360° Coverage
UV Light
Technology
Ceramic Chip
Applicator
Black Light
Inspection
Flashlight
Disinfect every surface with our 360º Spraying nozzle . Our spray
technology is one professional fix that uses an electrical charge to allow the
appropriate sanitizers and disinfectants to wrap around and evenly coat all
types of surfaces for a more complete clean. Nothing is left behind.
According to studies, viruses are sensitive to light and heat. Our Sprayer UV
Light Technology is proven to kill any virus like coronaviruses. We are the
first in the market to have a UV Technology to assist with disinfecting.
Our Black Light Inspection detect items that contain fluorescers within
them when the UV rays from the light shine on them. Some of the spills a
person might find with a black light include: Biological stains: saliva, semen,
urine and blood. Laundry stains: dried liquid detergents.
Our nozzle is consist of ceramic that is made of crystal, it doesn’t corrode
or rust, making our material more reliable. Ceramic material is known to be
an excellent dielectric because of its poor conductivity and also an efficient
supporter of the electrostatic fields.
BROADBAND
INNOVATION
CONTENTS
Ⅰ. Illustrated Parts
I. Product Higlights
II. Technical Parameters
III. Working Principle
IV. Operation instructions
V. Precautions and Safety Information
VI. Product Maintenance
VII. Failure and Solution
VIII. Attentions
IX. Warranty Service
X. Packing List
ⅩI. Warranty Card
1
2
3
4
5
7
8
9
10
11
12
BROADBAND
INNOVATION
NEX-ES BP360UV Electrostatic
Sprayer User Manual
Wind gun
Black
Light Bulb
UV and
Power Switch
Spray Nozzle
UV Light
Electrostatic switch
Handle
Label
Tank
Charging
Meter
Fan cover
Black Light Inspection Flashlight
01
Fan
I. Illustrated Parts
Precaution:
Always use appropriate PPE with any disinfectant or sprayer.
Never Point UV Light or Blacklight at skin or eyes.
1
2
3
4
5
7
8
9
10
11
12
BROADBAND
INNOVATION
I. Product’s Highlights
Fine Atomization
These sprayers were designed with a very thin nozzle. Almost 4 times
smaller than a conventional sprayer. This produces an extremely fine mist
allowing it to be airborne longer and provide more complete coverage of
the surfaces being sprayed.
Strong Adhesion
The electrostatic sprayer sends out your chemical solution as a charged
particle. This particle is the opposite electrical charge of the surfaces
being treated and therefore your treatment solution is strongly attracted
to those surfaces. Once it reaches the surface it wraps itself around the
entire exposed area providing 360-degree protection. This gives you the
best disinfecting (or pest control) possible and saves you the amount of
disinfectant or insecticide need to achieve the same results with a
conventional sprayer or fogger.
High Efficiency
The electrostatic mist is so fine that it does not over saturate surfaces and
therefore drip off of the treated surface. It forms a film that completely
encapsulates the surface on all sides due to the particle attraction. For
example, no matter which angle you disinfect a surface from, the charge
created by the electrostatic sprayer makes the disinfectant wrap around
and cling to the entire surface. This improves the efficiency and effect of
the product being sprayed. With this “touchless” method, this can all be
achieved from a safe distance for the user. When used with the proper
disinfectant (or insecticide), it will kill unwanted pathogens or insects from
every targeted surface. This unit is designed to treat more square footage
effectively and safely in less time.
NEX-ES offers a Triple Threat Option of Electrostatic, UV Technology &
Superior Disinfectant Solution
02
BROADBAND
INNOVATION
Ⅱ. Technical Parameter
Model
Battery
Tank capacity
Sprayer body
Working times
Charging time
Nozzle Sprayer Sizes
Rated Voltage
Effective range
Battery capacity
Rated power
Net weight
Gross weight
Warranty
Application
NEX-ES BP360UV
DURACELL Rechargable
ABS material
10L(2.27Gallons)
8 hours at 1A - (without fan open)
3.5 hours - (with fan open)
4.5 Hours
50, 80, 120 micron 360° fan
3-6m (Electrostatic with fan open)
1-2m (Electrostatic with fan off
24V
30AH
200W
7.8kg
11.5kg
See warranty instructions
Can be used for indoor/outdoor/Environmental
disinfection/Cleaning/Epidemic prevention/
Public place/Hospital/Building
03
Electrostatic spray technology is one professional fix that uses an electrical
charge to allow the appropriate sanitizers and disinfectants to wrap around and
evenly coat all types of surfaces for a more complete clean.
We are the first in the market to have a UV Technology to assist with
disinfecting.
Black Light Inspection detect items that contain fluorescers within them when
the UV rays from the light shine on them. Some of the spills a person might find
with a black light include: Biological stains: saliva, semen, urine and blood.
Laundry stains: dried liquid detergents.
Ⅲ. Electrostatic working principle
An electrode
atomizes the
cleaning solution
The charged particles
are attracted to the
surface area
The particles wrap
around the surface
3D objects & hard-to-reach
places receive a clean,
even coat
UV Light Technology
Black Light Inspection Flashlight
BROADBAND
INNOVATION
04
BROADBAND
INNOVATION
Ⅳ. Operation instructions
05
Always wear the appropriate PPE protection while using the unit
1. Set up.
a. Take the sprayer components out of the box and remove the individual parts
bags from inside the container
b. Select the appropriate nozzle size that you would like to use:
i. Ceramic Chip Applicator Nozzle-Very Fine Mist (shorter drying time)
ii. Other Nozzle- Medium - Heavy Mist
c. Place the tank filter into the hole in the bottom of the tank
d. Place the solution strainer in the top of the tank, fill with the appropriate
solution and replace the tank cover
e. Attach the battery and charge if necessary (see instructions below),
you can use the voltage gauge on the back of the tank to check the amount
of batter charge left.
This unit is equipped with a high capacity, DURACELL Ultra battery.
It is one of the best in class on the market with no memory effect,
stable performance and long-life cycle.
2. Charging.
a. First, Plug the charger into the charger hole at the base of the tank.
b. plug the other end of the cord into the 110V power outlet.
c. At this time, the charging indicator will be "red”.
d. When the indicator light turns "green", it indicates that charging is complete.
e. NOTE: the charging time can vary according to the amount of charge
remaining in the battery. A completely dead battery can take up to 4-6 hours
to completely recharge.
BROADBAND
INNOVATION
4. Prepare for Use
a. Refill the tank with your chemical solution.
b. There is a power switch which is located on the left side of the base of the
tank next to the outlet for the power supply charger.
c. The power switch on the base must be turned on before the power switch at
the handle is turned on.
d. Turn on the electrostatic function but turning on the orange switch on the
handle. The orange switch is what keeps the unit in electrostatic mode.
e. Turn on the sprayer and run for 30 seconds to one minute to purge the lines
of any remaining testing water or cleaning solutions used previously
f. Begin using your sprayer.
2. Test spray.
a. Open the cap of sprayer tank fill cover
b. Add a small amount of water into the tank for testing
c. Turn on the power switch on the tank and then turn on the
power switch on the handle
c. test for a minute or two to make sure there are no leaks at all of the joints,that
the pressure is normal and that you have selected the appropriate nozzle for
the type of work that you are doing.
d. Once the adjustments above have been completed, empty the water
from the tank.
06
BROADBAND
INNOVATION
a. The electrostatic sprayer is safe to use. In a rare event you might experience
a small static electric shock, but this unit will not harm the human body.
b. Please do not touch the nozzle parts by hand directly while running the unit.
After shutting down, the nozzle should contact any surface (or crop) or the
ground to eliminate residual static electricity.
c. All of the components of this sprayer are designed to work together. Please
use the supplied hose and nozzle handle. You cannot remove them to replace
with other hoses, wands or nozzles. Risk of electrical shock if interchanged
with others.
d. Do not let the nozzle directly touch any of the surfaces when spraying.
Remaining 3-10ft away from surfaces should achieve the desired effect.
e. When using the unit for insecticide treatment outdoors, it is not advisable to
use this static electric device in an environment with high humidity such as
foggy or rainy days. NEVER USE this unit when a thunderstorms or lightning
are near or present.
f. This sprayer is not allowed to be filled with, spray or use any flammable,
explosive, highly corrosive substances, such as alcohol, gasoline, benzene and
high alcohol-based disinfectants (Chemicals must be water soluble and diluted
according to chemical manufacturers instructions before use).
V. Precautions and Safety Information
07
BROADBAND
INNOVATION
08
a. When the sprayer is not being used for extended periods of time, it must be
recharged every two months to extend battery life.
b. After each use, the unused liquid must be poured out. Pay close attention as
to where you dispose of the unused portion as to not pollute the environment.
c. Rinse or clean the tank after every used with water or a neutral detergent to
prepare for its next use. It is forbidden to clean the sprayer with Tianna water
or gasoline. When cleaning the exterior of the machine with water or other
neutral detergents, care must be taken not to put water or neutral detergents
into the motor casing.
e. Run the sprayer for a minute or so with water only to clean any remaining
treatment chemicals from the hose and nozzle. This will avoid corrosion or
damage to any of the parts, enhance the service life and prevent nozzle clogs
in the future.
f. Drain the tank and let dry before putting the cap back.
VI. Product Maintenance
BROADBAND
INNOVATION
VII. Failure and Solution
Problem Cause Solution
Cannot be started or
suddenly stops working
1) The battery is out of power or
poor connection.
2) Circuit breaker (located by
power switch on tank) tripped as
the machine is too hot.
1) Check the lines fix the
plug correctly.
2) Don't use it until the electric
equipment cools down.
The liquid is not spraying
out through the nozzle or
the pressure is unstable
Low Pressure
Joint is leaking
Not spraying well or properly
1) Holes of the nozzle are blocked
2) Air in hose
3) A blockage in the water pump
somewhere
4) Water suction tube is
broken or fell off.
1) Filter net in the tank mouth
or in the spraying switch is blocked.
2) Battery is out of power.
1) The joint has not been
screwed in tightly
2) Rubber seal is broken
1) Nozzle is blocked
2) The core of nozzle is broken
1) Tighten the joint
2) Replace the rubber seal
1) Remove foreign substance
2) Replace the core
1) Wash/clean the filter net
2) Charge up the battery
1) remove and wash, clean,
blowout the nozzle.
2) Check the hose for leaks,
screw tightly, run to expel the air
3) Dismantle the water pump's
cover and clean water pump.
4) Replace the tube.
09
BROADBAND
INNOVATION
VIII. Attentions
1.
2.
3.
4.
5
6.
7.
8.
9.
10.
11.
Please make sure the battery capacity is enough before use.
Please charge it when the light become red.
If the water goes into the machine, make sure it completely dry before
turn on the switch.
The operating ambient temperature of the machine is between
32-104F. It should not be knocked with heavy object, avoid falling from
high place. The customer must use special battery configured by this
product. It is forbidden to use other types of batteries to avoid
damage to the product.
Please don’t use it to work when charging.
If you leave it unused for a long time, please fully charge the better.
Prohibit using the strong corrosion liquid, the solution should be
completely dissolved without impurities. To prevent clogging the
pipeline.
If below situations happen, please cut off the power supply
immediately.
1)The water gets into machine.
2)The motor stops working suddenly.
3)The voice of motor changes obviously.
4)The water tank leaks.
5)The motor is not work or other abnormal conditions happen when
turning on.
Please cut off the power supply after using and clean the tank
promptly. Put it in a safe location to avoid water drenching, direct
sunlight, bump and kid’s touch.
Please cut off the power immediately and cleaning tank when you
finish the work. Put it in the safe place and avoid any exposure to wet,
sun collision and easy to be reached by children.
Do not use the machine in the rain. Forbid to plug or unplug with wet
hands. The machine should not be stored near any flammable,
explosive articles or high temperatures sites.
If abnormal condition happens, please contact with us.
10
BROADBAND
INNOVATION
IX. Warranty Service
We provide one year free maintenance for the main components of the
equipment.
List of major components:
1)Motor
2)Electromc control board
3)Battery (warranty for liquid leakage, plastic shell cracking, etc.
Except for human factors and external damage)
4)Charger
5)Water tank
6)Single Valve
7)Nozzle
Parts that are not in the main components list are all warranted for 3
months (except for human factors, external damage and improper use)
The below circumstances are exclusive of the warranty service:
1)The blockage and damage of equipment because of using strong
corrosion liquid
2)The fault and damage because of changing the structure and replacing
the parts of equipment privately.
3)Do not follow the instructions for use and maintenance.
4)Artificial damage caused by improper or overuse.
5)Damage caused by irresistible natural forces, such as earthquakes,
fioods,fires, etc.
1.
2.
11
BROADBAND
INNOVATION
X. Packing List
ⅩI. NEX-ES BP360UV-Warranty Card
No. Item Specification Qty Remarks
1
2
3
4
5
6
7
1
1
1
1
1
1
3sets
Sprayer
Charger
Flashlight
Straps
UV Light
Nozzles
User Manual
50 micron, 80 micron, 120 micron 6 nozzles in 1 set
User name
Address
Contact
Purchase place
Order NO.
Date of purchase
Zip code
Country
Distributor
Model NO.
User signature
Note
Product name
Serial NO.
Distributor signature
12
/