2. Avallon
  3. AIMG151GIRH
AIMG151GIRH

Avallon AIMG151GIRH User manual

  • Hello! I have reviewed the installation instructions for the Avallon icemaker models AIMG151GPRILH, AIMG151GPRIRH, AIMG151PPRILH, and AIMG151PPRIRH. This document details how to install custom door panels, including required tools, step-by-step instructions, and door dimensions. I'm ready to answer your questions about the installation process and the device itself.
  • What tools are required for panel installation?
    Is the hardware for mounting the overlay panel included?
    What is the maximum weight of the overlay panel?
    Can I install my own handle?
1
AVALLON.COM
®
©2022 Ferguson Enterprises, LLC V1.0-04012022
Thank you for purchasing your panel ready gourmet icemaker from Avallon. Our brand set out with one parcular goal: To present
appliances that are as reliable and recognizable as they are aainable. We create products that invite enre kitchens to be built around
them, serving as an establishing feature in the very spaces they occupy.
In accordance with our ongoing mission to provide cung-edge and forward-thinking products to our loyal customers, we recently
introduced a line of panel ready appliances. These models are fully customizable, and in just a few short steps, you can match your
undercounter icemaker with your adjacent cabinetry.
This document serves as a guide for installing custom door panels on any of these models. For more product informaon, including owner's
manuals, dimension guides, and more, visit Avallon.com.
PRODUCT INFORMATION
PANEL INSTALLATION INSTRUCTIONS
OVERLAY PANEL INSTALLATION INSTRUCTIONS
TOOLS REQUIRED
• Phillips Screwdriver • Drill and 7/64" Drill Bit • #6 Wood Screws* • Clamps (Recommended)
IMPORTANT
Warning: The weight of the overlay panel should not exceed 15 lbs.
NOTE
*Because the sizes of overlay panels vary, hardware for mounng your overlay is not included with your Avallon panel
ready icemaker. #6 wood screws are recommended. The required length depends on the thickness of your overlay panel.
Take care to ensure the screws are not too long to avoid them protruding though the overlay panel.
1. Open the door.
2. Using a Phillips screwdriver, remove the two screws from the top hinge bracket and carefully li the door o the boom hinge. Set the
screws and bracket aside in a safe locaon.
2
AVALLON.COM
®
©2022 Ferguson Enterprises, LLC V1.0-04012022
3. Place the door (front facing downward) on a blanket, sheet of cardboard, or other so material before proceeding.
4. Peel away and remove the door gasket from the inside of the door as shown below. We recommend starng at one corner and gently
pulling to avoid tearing the gasket. Set the gasket aside in a safe locaon.
5. Place the door (front facing downward) on top of the overlay panel as shown below. Align the boom edge of the overlay panel with the
panel bracket at the boom of the door. We recommend clamping the two pieces together before proceeding to prevent movement and
misalignment.
Overlay Panel
Panel Bracket
6. Drill pilot holes into your overlay panel using the screw hole openings in the Avallon door for exact placement.
7. Use four #6 wood screws of the correct length to secure the overlay panel to the door. The length of screw depends on the thickness of
your overlay panel. Take care to ensure the screws are not too long to avoid them protruding though the overlay panel.
8. Use three #6 wood screws to secure the boom of the overlay panel to the bracket at the boom of the door.
9. Your Avallon icemaker comes with a standard towel bar handle. If you choose to install this handle, do so using the designated holes in
the door. Hole posioning is shown on the diagram on the last page.
10. Replace the door gasket.
11. Place the door back on the boom hinge and then replace the top hing bracket screws with a Phillips screwdriver. Make sure the door is
secure.
3
AVALLON.COM
®
©2022 Ferguson Enterprises, LLC V1.0-04012022
DOOR DIMENSIONS AND SCREW PLACEMENT
14 11/16” (372.5mm)
13 1/8” (333mm) 3/4” (19.8mm)
10 9/16”
(268mm)
5 1/8”
(129.5mm)
13/16”
(20.5mm)
29 1/2”
(749mm)
19 5/16”
(490mm)
3/4” (19mm)
*Handle screw placement for left hinged models is reversed.
IMPORTANT
Warning: The images below are for reference only. Due to manufacturing tolerances, the locaon of the bores in the door
for screw placement may vary slightly. We strongly recommend having the Avallon unit on-site prior to drilling pilot holes
in the overlay panel.
MODELS: AIMG151GPRILH, AIMG151GPRIRH, AIMG151PPRILH, AIMG151PPRIRH
/