ALUMINUM ARM FOLDING KITS
DoorKing Part Numbers:
This kit is designed ONLY for the 1601 and 1603 model barrier gate operators
with or without LEDs. Recommended for low headroom applications.
Wire Run Secured
to T
op of Cabinet
Knock Out
Stud
Wire Harness
(for LED
model)
Included
Adhesive
Zip Ties
Knock Out
Far Side
Option
Near Side
Option
7.5 ft
Flex Cable
(for LED model)
Remove stud (see below) from operator
housing and assemble as shown.
Operator Top
1601-600
Folding LED Arms
1601-610
Folding Arms
Installation
Ar
m Bracket
Cover
Hub
LED Wire for Inner Arm (for LED model)
Elbow
Cable
Assembly
Operator
Cable Assembly
Wire Run Options
(for LED model)
Arm Connection to Operator
Bushing
See back page
to wire power.
9/16” Bolt
Pre-Crimped Eyelet
Lockwasher
Nut
Cable
Clamps
Cable
End of Cable
U-Bolt
Nut
Cable
Cable Eyelet
Eye Bolt
Plastic End Cap
7 1/2 ft Flex Cable through
elbow assembly to outer arm.
(for LED model)
Self-Tapping Screws Through
Pre-Drilled Holes in Arm
Self-Tapping Screws Through
Pre-Drilled Holes in Arm
Inner Arm
Outer Arm
Inner Arm
7 1/2 ft Flex Cable Through inner arm
to Wire Harness (for LED model)
Blue to Blue
Red to Red
(for LED model)
Blue to Blue
Red to Red
(for LED model)
Wire Harness LED Note: There needs to be slack
in the wire harness for rotating arm on LED model.
Note: Arm bracket, hub
and cover NOT included.
LED Wire
for Outer Arm
(for LED model)
Female Connectors
on Flex Cable
Male
Connectors
IMPORTANT:
OUTER LED ARM has LED wire exiting
from the SAME end as the self-tapping
pre-drilled screw holes.
LED Wire for
Inner Arm
to Wire Harness
(for LED model)
IMPORTANT:
Cable MUST be
clamped as shown.
1603 Max Height 104.9”
1601 Max Height 100.9”
DoorKing Part Numbers:
1601-600
Folding LED Arms
1601-610
Folding Arms
MOVING ARM
can
cause vehicle damage,
serious injury or death.
STAY CLEAR
of arm
at all times.
NO:
Pedestrians
Bicycles
Motorcycles
WARNING
MOVING ARM
can
cause vehicle damage,
serious injury or death.
STAY CLEAR
of arm
at all times.
NO:
Pedestrians
Bicycles
Motorcycles
WARNING
MOVING ARM
can
cause vehicle damage,
serious injury or death.
STAY CLEAR
of arm
at all times.
NO:
Pedestrians
Bicycles
Motorcycles
WARNING
MOVING ARM
can
cause vehicle damage,
serious injury or death.
STAY CLEAR
of arm
at all times.
NO:
Pedestrians
Bicycles
Motorcycles
WARNING
Drawings not to scale
Outer Arm
Wire
Harness
Slack
Inner Arm
Eye
Bolt
Cable
Clamps
MOVING ARM
can
cause vehicle damage,
serious injury or death.
STAY CLEAR
of arm
at all times.
NO: Pedestrians
Bicycles
Motorcycles
WARNING
Moving Gate Can Cause
Serious Injury or Death
KEEP CLEAR! Gate may move at any time
without prior warning.
Do not let children operate the gate or play
in the gate area.
This entrance is for vehicles only.
Pedestrians must use separate entrance.
Layout
Adjust cable with eyebolt and cable clamps to level outer arm in DOWN position ONLY.
IMPORTANT: DO NOT adjust cable too tight or it will bind when operating.
Shortening LED Arms Note: If arms MUST be
shortened, DO NOT cut through the LEDs. Only cut
arms so the LEDs WILL NOT get damaged.
Power Arm LEDs from Operator
(for LED model)
Plug power transformer into wire harness.
Connect supplied power transformer to 115 VAC power.
Use existing wire restrainers to secure wire.
Make sure all wires are clear of moving parts.
1601-265-J-8-18
Copyright 2018 DoorKing, Inc. All rights reserved.
120 S. Glasgow Avenue
Inglewood, California 90301
U.S.A.
Red+
Black-
Existing Wire
Restrainer
Wire
Harness
115 VAC
Convenience
Outlet
1601
OR
1603
Power
Transformer
Tr
ansformer Plug
Max Length 143.5”
Wire Harness LED Note:
There needs to be slack in
the wire harness for rotating
arm on LED model.
/