LifeGear 27758 Owner's manual

Spinning Bike

ITEM NO.: 27758

OWNER’S MANUAL

IMPORTANT: Read all instructions carefully before using this product. Retain this

owner’s manual for future reference.

The specifications of this product may vary from this photo and are subject to change without

prior notice.

1

TABLE OF CONTENTS

WARRANTY ------------------------------------------------------------------------------- 2

IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3

PARTS LIST ------------------------------------------------------------------------------- 4

TOOLS -------------------------------------------------------------------------------------- 6

EXPLODED VIEW ----------------------------------------------------------------------- 7

ASSEMBLY INSTRUCTIONS -------------------------------------------------------- 8

HOW TO MOVE THE BIKE ------------------------------------------------------------ 16

OPERATING THE COMPUTER ------------------------------------------------------ 17

ADJUSTMENTS -------------------------------------------------------------------------- 19

EMERGENCY STOP -------------------------------------------------------------------- 22

MAINTENANCE -------------------------------------------------------------------------- 23

TROUBLESHOOTING ------------------------------------------------------------------ 23

WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 24

2

ONE YEAR LIMITED WARRANTY

LifeGear Inc. warrants to the original purchaser that this product is free from defects in

material and workmanship when used for the purpose intended, under the conditions that it

has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's

obligation under this warranty is limited to replacing or repairing free of charge, any parts

which may prove to be defective under normal home use. This warranty does not include

any damage caused by improper operation, misuse or commercial application.

From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.

This warranty is offered only to the original owner and is not transferable. Proof of

purchase is required.

When ordering replacement parts please have the following information ready:

1. Owner's Manual

2. Model Number

3. Description of Parts

4. Part Number

5. Date of Purchase

3

IMPORTANT SAFETY INSTRUCTIONS

Basic precautions should always be followed, including the following safety

instructions when using this spinning bike. Read all instructions before using this

spinning bike.

1. Read all the instructions in this manual and do warm up exercises before using this

equipment.

2. Before exercise, in order to avoid injuring your muscles, warm-up exercise for every

muscle group is highly recommended. Please refer to the Warm Up and Cool Down

Routine pages for pre and post workout.

3. Please make sure all components are not damaged and in working order before use.

This equipment should be placed on a flat surface while in use. Using a mat or other

material on the ground is recommended.

4. Wear comfortable and suitable clothing when using the spinning bike. Do not use the

spinning bike barefoot, in only socks or in sandals, always wear athletic shoes.

Never wear loose clothing that might catch any part of the equipment.

5. Do not attempt any adjustments other than those described in this manual. Should any

problems arise, discontinue use and consult your local dealer.

6. Keep Dry - do not operate in a wet or moist condition.

7. Always hold on to the handlebar while using the equipment.

8. To dismount, reduce pedaling speed gradually before you stop.

9. Do not use the equipment outdoors. It is not a commercial model.

10. This equipment is for household use only.

11. Only one person should be on the equipment while in use.

12. Keep children and pets away from the product while in use. This machine is designed

for adults only. The minimum free space required for safe operation is not less than

two meters. Be sure the area around the spinning bike remains clear during use and

has adequate clearance.

13. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop

exercising immediately and consult your physician before continuing.

14. The maximum weight capacity for this product is 110 kgs.

Note: It is the obligation of the owner to review and explain these important safety

instructions to all users of this spinning bike.

WARNING: Before beginning any exercise program consult your

physician. This is especially important for the people who are over 35 years old or

who have pre-existing health problems. Read all instructions before using any

fitness equipment.

CAUTION: Read all instructions carefully before operating this product.

Retain this Owner’s Manual for future reference.

4

PARTS LIST

No. Description Qty No. Description Qty

001 Main Frame 1 023 Sensor with Wire (L=850 mm) 1

002 Handlebar Post 1 024 Washer Ø9xØ5x1.0T 2

003 Seat Post 1 025

Cross Recessed Pan Head Bolt

M5x15

2

004 Seat Sliding Tube 1 026 L-Shape Knob M10 1

005 Handlebar 1 027 Washer Ø30xØ10.5x2.5T 1

006 Handlebar Adjustment Plate 1 028 Computer ST-6521 1

007 Front Stabilizer 1 029

Cross Recessed Pan Head Bolt

M5x10

4

008 Rear Stabilizer 1 030 Hand Pulse Sensor 2

009

Hexagon Socket Pan Head Cap

Bolt M8x20

4 031

Cross Recessed Pan Head Self

Tapping Screw ST4.2x20

8

010 Washer Ø8xØ20x2.0T 4 032 Wire Grommet Ø12.1 5

011 Adjustable Leveler M10x30 4 033 Seat Cushion 1

012 Hexagon Nut M10 4 034 Seat Sliding Tube Cover 1

013

Stabilizer End Cap (□40x80)

4 035

Cross Recessed Pan Head Self

Tapping Screw ST4.2x15

2

014

Hexagon Socket Pan Head Cap

Bolt M6x15

2 036

Seat Sliding Tube Square End

Cap (□38x1.5)

1

015 Bearing 608 4 037

Hexagon Socket Round Head Bolt

M8x16

1

016 Transport Wheel Ø71x24 2 038

Seat Adjustment Knob

M16x1.5x20

1

017

Hexagon Socket Pan Head Cap

Bolt M6x12

2 039 Seat Sliding Tube Stopper Ø18x18 1

018 Left Foot Pedal 9/16" 1 040 Hexagon Socket Bolt M6x8 1

019 Right Foot Pedal 9/16" 1 041 Bushing Ø60 2

020 Water Bottle Holder 1 042

Cross Recessed Pan Head Self

Tapping Screw ST4.2x6

4

021

Cross Recessed Pan Head Self

Tapping Screw ST4.8x15

2 043 Tension Knob 1

022 Round Knob M16x1.5x18 2 044 Square Bushing 20x20x30 1

5

PARTS LIST

No. Description Qty No. Description Qty

045 Left Decorative Cover 1 068 Small Chain Wheel 1

046 Right Decorative Cover 1 069 Lock Nut M33x1.0x4.0T 2

047

Cross Recessed Pan Head Self

Drilling Tapping Screw ST4.2x20

6 070 Flywheel Shaft M12x168 1

048 Spring Ø15xØ2x60 1 071 Nut M12x1.0x7T 1

049 Square Nut M10 1 072 Chain 1

050 Cone Nut M10 1 073

Cross Recessed Pan Head Bolt

M6x10

2

051 Brake Pad Plate 119x30x35 1 074 Crank Cover 2

052 Brake Pad 115x25x6 1 075 Hexagon Flange Nut M10x1.25x9 2

053 Hexagon Head Bolt M5x35 2 076 Left Crank 9/16" 1

054 Small Spring Plate 1 077 Right Crank 9/16" 1

055 Washer Ø5xØ10x1.0 2 078 Plastic Cover 1

056 Cap Nut M5 2 079

Cross Recessed Countersunk

Head Screw M8x15

4

057 Rubber Pad 38x25x4.0T 1 080 Crank Shaft Ø17x176 1

058 Hexagon Head Bolt M6x15 2 081 Chain Wheel Ø205 1

059 Cap Nut M12x1.0 2 082 Spring Washer Ø8 4

060 Eyebolt M6x48 2 083 Hexagon Nylon Nut M8 4

061 Hexagon Nut M6 4 084 C Ring Ø17x1.0 2

062 Sleeve Ø18xØ12x6 2 085 Bearing 6203Z 2

063 Hexagon Nut M12x1.0x7T 2 086 Plastic Cover Board 1

064 Sleeve Ø18xØ12x16.5 1 087 Wave Washer Ø17xØ21x0.3 1

065 Bearing 6001Z 3 088 Crank Cap Ø45 1

066 Magnet Ø15x7 1 089

Cross Recessed Pan Head Self

Drilling Tapping Screw ST4.2x15

1

067 Flywheel Ø453x35 (18 kg) 1 090

Hand Pulse Sensor Wire

(L=1000 mm)

1

6

TOOLS

Allen Wrench S6

1 PC

Multi Hex Tool with Phillips Screwdriver

1 PC

7

23

89

32

23

32

41

42

41

42

43

44

45

46

47

59

60

62

59

60

61

62

71

70

69

68

65

67

64

63

66

50

49

48

57

58

56

55

53

54

52

51

72

47

82

81

80

79

83

31

73

77

88

87

76

75

74

31

78

84

85

86

85

75

74

61

9

10

11

12

8

13

11

12

38

39

40

4

36

37

33

34

35

18

L

3

22

19

20

21

2

22

14

15

16

15

17

15

16

14

11

12

11

12

7

9

10

13

28

29

31

1

5

6

23

24

25

26

27

30

31

32

90

EXPLODED VIEW

8

ASSEMBLY INSTRUCTIONS

STEP 1

Use the Allen Wrench to loosen the bolts in the Main Frame (1). Remove the bolts and

cardboard tubes from the Main Frame (1).

STEP 2

Install four Adjustable Levelers (11) onto the Front and Rear Stabilizers (7, 8).

11

8

7

11

1

9

STEP 3

Remove four Hexagon Socket Pan Head Cap Bolts (9) and four Washers (10) from the

Front and Rear Stabilizers (7, 8). Remove bolts with the Allen Wrench provided.

STEP 4

Position the Front Stabilizer (7) which has one pair of the transport wheel in front of the

Main Frame (1) and align bolt holes.

Attach the Front Stabilizer (7) onto the front of the Main Frame (1) with two Hexagon Socket

Pan Head Cap Bolts (9) and two Washers (10) that were removed. Tighten bolts with the

Allen Wrench provided.

9

10

7

8

9

10

1

9

10

7

9

10

9

10

7

1

7

Transport Wheel

10

STEP 5

Position the Rear Stabilizer (8) behind the Main Frame (1) and align bolt holes.

Attach the Rear Stabilizer (8) onto the rear of the Main Frame (1) with two Hexagon Socket

Pan Head Cap Bolts (9) and two Washers (10) that were removed. Tighten bolts with the

Allen Wrench provided.

STEP 6

The Cranks and Pedal Shafts are marked with the letter R (Right) and L (Left) to denote

the side of the spinning bike they are on.

Insert the pedal shaft of Left Foot Pedal (18) into threaded hole in the Left Crank (76). Turn

the pedal shaft by hand in the counterclockwise direction until snug.

NOTE: DO NOT turn left foot pedal shaft in the clockwise direction, doing so will strip

the threads.

Tighten the pedal shaft of Left Foot Pedal (18) with the Multi Hex Tool with Phillips

Screwdriver provided.

Insert pedal shaft of Right Foot Pedal (19) into threaded hole in Right Crank (77). Turn the

pedal shaft by hand in the clockwise direction until snug.

NOTE: DO NOT turn right foot pedal shaft in the counterclockwise direction, doing so

will strip the threads.

Tighten pedal shaft of Right Foot Pedal (19) with the Multi Hex Tool with Phillips Screwdriver

provided.

9

10

8

1

9

10

8

1

L

18

19

R

1

L

77

76

11

STEP 7

Loosen nuts from underside of the Seat Cushion (33) with the Multi Hex Tool with Phillips

Screwdriver provided. Then install the Seat Cushion (33) onto the Seat Sliding Tube (4)

and secure with nuts that were loosened. Tighten nuts with the Multi Hex Tools with Phillips

Screwdriver provided.

STEP 8

Insert the Seat Post (3) into the tube of the Main Frame (1) and align round knob holes.

Then attach the Round Knob (17) onto the tube of the Main Frame (1) by turning it in a

clockwise direction to tighten the Seat Post (3) in the suitable position.

3

4

33

Nut

3

22

1

3

22

1

12

STEP 9

Insert the Handlebar Post (3) into the tube of the Main Frame (1) and align round knob holes.

Then attach the Round Knob (17) onto the tube of the Main Frame (1) by turning it in a

clockwise direction to tighten the Seat Post (3) in the suitable position.

STEP 10

Attach the Handlebar (5) onto the Handlebar Post (2) with one L-Shape Knob (26), one

Washer (27), and one Handlebar Adjustment Plate (6) . Turn the L-Shape Knob (26) in a

clockwise direction to lock the Handlebar (5) in place.

22

2

22

2

1

5

2

6

26

27

13

STEP 11

Remove two Cross Recessed Pan Head Self Tapping Screws (21) from the Main Frame (1).

Remove screws with the Multi Hex Tool with Phillips Screwdriver provided.

STEP 12

Attach the Water Bottle Holder (20) onto the Main Frame (1) with two Cross Recessed Pan

Head Self Tapping Screws (21) that were removed. Tighten screws with the Multi Hex Tool

with Phillips Screwdriver provided.

21

1

20

21

1

14

STEP 13

Remove four Cross Recessed Pan Head Bolts (29) from the back of the Computer (28).

Remove bolts with the Multi Hex Tool with Phillips Screwdriver provided.

STEP 14

Insert the wires that come from the Computer (28) through the hole in the computer bracket

of the Handlebar (5). Then, place the Computer (28) onto the computer bracket of the

Handlebar (5) and align bolt holes.

Attach the Computer (28) onto the computer bracket of the Handlebar (5) with four Cross

Recessed Pan Head Bolts (29) that were removed. Tighten bolts with the Multi Hex Tool

with Phillips Screwdriver provided.

28

29

5

28

29

28

29

5

28

15

STEP 15

Connect the Sensor Wire (23) to the wire that comes from the Computer (28).

Plug the Hand Pulse Sensor Wire (90) and the wire that comes from the Computer (28).

23

90

28

5

23

28

90

28

5

16

HOW TO MOVE THE BIKE

This spinning bike has a pair of Transport Wheels built into the front stabilizer and can be

carefully tilted onto its Transport Wheels for easy moving and storage.

To move the spinning bike, stand in front of the bike, firmly grasp the Handlebar with both

hands. Next, carefully push the bike down until it rolls freely on the Transport Wheels.

CAUTION: It is suggested you always use the aid of a second person when moving

the bike.

Handlebar

Transport Wheel

17

OPERATING THE COMPUTER

DISPLAY FUNCTIONS:

ITEM DESCRIPTION

SCAN

. Automatically scan through each function in sequence every 6 seconds.

. In SCAN mode, press the mode/reset key to choose functions.

. The sequence of display when press the mode/reset key: TIME→

DISTANCE→CALORIES→PULSE→RPM/SPEED

SPEED

. Range 0.0 ~ 99.9 KPH

. Without any signal being transmitted into the computer for 4 seconds during

workout, SPEED will display “0.0”.

RPM

. Range 0 ~ 999 RPM

. Without any signal being transmitted into the computer for 4 seconds during

workout, RPM will display “0”.

TIME

. Range 0:00 ~ 99:59 minutes:seconds.

. Without setting the target value, time will count up.

. When setting the target value, time will count down from your target time to 0

with an alarm sound and flash.

. Without any signal being transmitted into the computer for 4 seconds during

workout, time will STOP.

DISTANCE

. Range 0.00~99.99 kilometers.

. Without setting the target value, distance will count up.

. When setting the target value, distance will count down from your target

distance to 0 with an alarm sound and flash.

CALORIES

. Range 0~9999 kcal.

. Without setting the target value, calorie will count up.

. When setting the target value, calories will count down from your target

calorie to 0 with an alarm sound or flash.

PULSE

. Displays your current heart rate figures after you grip the handlebar hand

pulse sensors with both your hands during exercise.

. Without any pulse signal for 6 seconds, the computer will display “P”.

. Pulse alarm will sound when current pulse is over the target pulse.

. Range 0-30~230 BPM

18

KEY FUNCTIONS:

USING YOUR COMPUTER:

The computer can be activated by pressing button or by pedaling. If you leave the

equipment idle for 4 minutes, the computer will enter into clock mode. The computer will

display temperature, time, month, date, and year.

HOW TO INSTALL THE BATTERY:

1. Remove the battery cover on the back of the computer.

2. Place one 3V button cell battery into the battery housing.

3. Insure the battery is correctly positioned.

4. Re-install the battery cover.

5. If the display is illegible or only partial segment appears, remove battery and wait 15

seconds before reinstalling.



ITEM DESCRIPTION

set

. Press the set key to set time, month, date, and year after installing a

battery.

. Press the set key to increase value. Press and hold the set key to

increase value faster.

. TIME setting range: 00:00~99:00 minutes (Each increment is 1:00 minute).

. DISTANCE setting range: 0.00~99.50 kilometers (Each increment is 0.5

kilometer).

. CALORIES setting range: 0~9990 kcal (Each increment is 10 kcal).

. PULSE setting range: 0-30~230 BPM (Each increment is 1 BPM).

mode/reset

. Choose each function by pressing the mode/reset key.

. Press and hold the mode/reset key for 2 seconds to reset all functions to

zero.

19

ADJUSTMENTS

Adjusting the Adjustable Leveler

Turn the Adjustable Leveler on the front and rear stabilizers as needed to level the spinning

bike.

Adjusting the Tension Knob

To increase the tension, turn the Tension Knob in a clockwise direction.

To decrease the tension, turn the Tension Knob in a counterclockwise direction.

Adjusting the Handlebar Fore or Aft Position

Loosen the L-Shape Knob by turning it counterclockwise direction. Slide the handlebar

forward or backward direction to the desired position. Lock the handlebar in place by

turning the knob clockwise direction.

The L-Shape Knob is spring loaded. If the L-Shape Knob strikes the handlebar post

while you’re trying to loosen or tighten it, pull on the L-Shape Knob and rotate it to a

different position and release it.

Make sure that the L-Shape Knob is locked in place before using the bike.

Adjustable Leveler

Tension Knob

L-Shape Knob

Page is loading ...

LifeGear 27758 Owner's manual

LifeGear 27758 Owner's manual

Related papers

Other documents