CROSSCO ES 2000 ROOF SEALER
CODE: RS001
DESCRIPTION Crossco ES 2000 Roof Sealer is a styrene acrylic resin sealer modified with
silicone, designed to give years of protection to all roof and walls.
Crossco Es 2000 Roof Sealer is an elastomeric sealant that expands and
contracts with the surface where it has been applied. This sealer is internally
plactized to retain their mechanical properties for many years exposed to
the sun and rain. It can be used on all types of roofs.
USES To waterproofing and protect countless roofs, which are in good conditions
such as: asphalt roof, polyurethane foam, concrete, galvanized metal,
EPDM membranes and layers of elastomeric acrylics. Crossco ES 2000
Roof Sealer refelcts sunlight and reduces interior temperature. When applied
properly, this product could help to reduce the energy costs. Energy saving
may vary baswed on geographics location and individual characteristic
of the structure.
ADVANTAGES * 100 % waterproof * reflect UV ray
* stop leak * reduces the interior temperature
* seal crack * easy to apply
PRODUCT CHARACTERISTIC
Color………………………
white
Dry Time/Touch.……
60 min
Vehicle Base………….
100% acrylic
Dry Time/Coats.…….
24 hrs
Weight/Gal…………...
12.00 lbs
VOC………….…………...
100 g/L
Solids/Weight……….
% +/- 2%
pH………………...……….
9 +/- 0.5
Solids/Volume………
% +/- 2%
Flash Point………….…
None
Viscosity………………..
soluble
Dry Film Thick………..
20 mils
APPLICATION
Make certain to clean the roof substrate thoroughly.
Remove all foreign matter and old, loose coating by sandblasting, high pressure
water blasting, or white brushing
Kill and remove all mildew or fungus growth on the substrate by washing with a
solution that kills same; the flush with water.
Remove existing mildew before priming and painting or repainting.
Scrub mildew surfaces with mixture surfaces with a mixture of 1 quart
Crossco Crosscrete and 3 quarts warm water. Reading warning on
label. Wear rubber gloves and safety glasses.
Clean cracks and apply one coat of Crossco ES 2000 Primer,
let dry 2-3 hours, apply a second coat and let dry 24 hours. Apply over the
crack and 2” to both sides, with a putty knife a coat of Crossco ES
2000 Crack Filler, flexible caulk or sealant and Crossco ES 2000
Patching Weave.
Crossco ES 2000 Roof Sealer should be apply with a heavy nap, roller
or spray applied with airless spray equipment. The objective is to
have a thick, even coating over the entire roof surface that when dry
will be 30 mils thick. Apply only at temperature above 50° F. It is
recommended that a light colorant be used with the first coating to
show the areas of coverage of the second coat.
Apply a at spreading rate of:
Metal roof ……………………...……………….. 100 sq.ft.
Wood roof………………………………………… 100 sq.ft.
Concrete surfaces……………………………… 50 sq.ft.
Built-up roofs……………………………………. 50 sq.ft.
General surfaces……………………………….. 50 sq.ft.
Never thin or dilute from full strength. Drying time is approximately
60 minutes, but early protective skin forms before drying. Cure time is
controlled by the thickness of the applied coating, relative humidity
and temperature
Allow 24 hours before recoating.
Select a warm, clear sunny day. Make sure there is no forecast of
rain. Do not apply after 4:00 PM. Keep rain free for 6 hours minimum
after application
Clean rollers or equipment after use with hot, soapy water.
CAUTION
Keep out of reach of children.
Contains acrylic resin. In case of eye contact, flush thoroughly with water.
Do not rub the eyes. In case of skin contact,
flush area immediately with clean water. If swallowed, induce vomiting.
Consult a physician immediately. Use adequate ventilation.
PACKAGING
1 US Gal
5 US Gal
/
