2. Computers & electronics
  3. Data storage
  4. Data storage devices
  5. Solid state drives
  6. Integral
  7. INSSD128GMSA6M

Integral INSSD128GMSA6M, INSSD256GMSA6M, INSSD32GMSA6M, INSSD64GMSA6M Datasheet

  • Hello! I am an AI chatbot trained to assist you with the Integral INSSD128GMSA6M Datasheet. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
i
i
Product Specification
256
GB
128
GB
64
GB
32
GB
Rev:1
FEATURES
• mSATA form factor with SATA III 6Gbps interface
(backwards compatible with SATA 3Gbps and SATA
1.5Gbps)
• Performance: Faster boot than HDD, Faster access to
applications, enhanced productivity and increased
efciency
• Fully compatible with devices and OS that support the
SATAstandardwithmSATAinterface
• Non-volatileFlashMemoryforoutstandingdataretention
–lesslikelytofailthanHDD
• Ultra-efcientBlockManagementandWearLevelling
• ErrorCorrectionCode
• LowerPowerConsumption
• Shockresistance–Nomovingpartsenabletheproductto
beusedintougherconditions
• Silentoperation-Noiselessandlowheatdissipation
• Supports S.M.A.R.T. — Self-Monitoring, Analysis and
ReportingTechnology
• SupportsTRIM
• RoHScompliant
• CEandFCCtested
• 2YearWarranty
mSATA6GbpsMO-300
INTRODUCTION
TheIntegralmSATA6GbpsMLCSSDdeliversallof
theadvantagesofashmemorytechnologywith
the Serial ATA III interface and conforms to the
mSATA standard generated by JEDEC, known as
MO-300.
mSATAisasmallformfactorSSDthatisaround8
timessmallerthanthetypical2.5inchSSD/HDD
available. It is ideal for adding storage to small
formfactorandembeddedsystems.
TheSATAIIIsuper-fastperformancethatisdelivered
by the Integral mSATA 6Gbps, together with its
reliability and low power operation make it the
idealSSDdriveforembeddingintonewsystems.
i
i
Product Specification
Rev:1
TechnicalFeatures
• MLC-NAND Flash Technology
• Cache Size: 32GB, 64GB & 128GB = 256MB DDR 3,
256GB = 512MB DDR 3
• mSATA
• JEDEC standard - M0-300
• Supports TRIM (OS support required)
• Supports S.M.A.R.T.
• CE and FCC certified and RoHs compliant
PERFORMANCE
32GB
Read 368MB/s (up to)*
Write 236MB/s (up to)*
64GB
Read 369MB/s (up to)*
Write 240MB/s (up to)*
128GB
Read 375MB/s (up to)*
Write 240MB/s (up to)*
256GB
Read 350MB/s (up to)*
Write 240MB/s (up to)*
INTERFACE
Interface
SATA III 6Gbps
Also Compatible with SATA II
3Gbps and SATA 1.5Gbps
*Based on internal testing
RELIABILITY
MTTF 2,000,000 hours
ECC algorithm
24 9-bit Symbols Correction per
512 9-bit Symbol
POWERCONSUMPTION
Supply Voltage 3.3V
Power Consumption (mA)
Read = 850min / 900max
Write = 580min / 830max
Idle = 80
ECC algorithm
Supports 72-bit ECC correct per
1K Byte
MTBF >1 Million Hours
ENVIRONMENTAL
Operating Temp 0° - +70°C
Non - Operating Temp -40° - +85°C
Humidity RH 90% under 40C in operation
PHYSICAL
Length 50.8mm
Width 29.85mm
Height 3.8mm
Weight 8g
Length (Packed) 115mm
Width (Packed) 132mm
Height (Packed) 57mm
Weight (Packed) 58g
WARRANTY
2 years
CAPACITY PARTCODE BARCODE(EAN)
32GB INSSD32GMSA6M 5055288421653
64GB INSSD64GMSA6M 5055288421660
128GB INSSD128GMSA6M 5055288421677
256GB INSSD256GMSA6M 5055288421684
1GB = 1,000,000,000 bytes. Formatted capacity is less.
This device should not be used as your sole backup.
Product design and specification subject to change or modification without notice. E&OE.
All trademarks acknowledged.
For warranty information please visit www.integralmemory.com/warranty
( 13.60 )
1.65
4.00
25.70
( 5.60 )
Pin 1
Pitch: 0.80
Pin 51
2 —RO.80 [Max.]
2.05
5.60
13.60
4.00
Pin 52
Pin 2
2.55 ±0.05
0.00
2.83
5.80
24.05
27.03
29.85
29.85
24.05
5.80
0.00
29.85
0.00
27.78
29.35
29.85
10.325
11.825
13.08
0.50
0.00
2.08
9.08
50.80
48.05
48.05
45.00
50.80
48.80 [Max.]
45.00
0.00
4.00
3.20 [Max.]
0.00
4.00
3.20 [Max.]
Details B Details C
2—ø2.60 holes
50.80
45.00
50.80
45.00
48.80 [Max.]
5.10 [Min.]
5.10 [Min.]
0.00
0.25 [Max.]
BOTTOM SIDE
PCB T=1.00±0.1
Details A
TOP SIDE
0.60 ±0.05
Details C
Details A
Details B
2 —O.25 [Max.]
2 —O.25 [Max.]
/