CHAUVET DJ SlimPACK 56 LT Reference guide

Quick Reference Guide

Pack Includes

Four SlimPAR™ 56 Lights

Four 3-pin, 10-foot DMX Cables

One Obey™ 3 Controller

One CHS-SP4 Carry Bag

SlimPACK™ 56 QRG EN

2

About This

Guide

The SlimPack™ 56 Quick Reference Guide (QRG) has basic

product

information such as mounting, menu options, and DMX values. Download

the User Manual from www.chauvetlighting.com for more details.

Disclaimer

The information and specifications contained in this QRG are subject to

change without notice.

Safety Notes

These Safety Notes include important information about

installation, use,

and maintenance.

• This product is not intended for permanent installation.

• ONLY connect this product to a grounded and protected circuit.

• Always disconnect from power before cleaning or replacing the fuse.

• DO NOT look at the light source when the product is on.

• Make sure the power cord is not crimped or damaged.

• Never disconnect this product from power by pulling on the cord.

• When mounting this product overhead, use a safety cable.

• DO NOT allow flammable materials close to the unit while operating.

•

DO NOT touch this product when it is operating because it may be hot.

• The voltage of the outlet to which you are connecting this product must

be within the range stated on the decal or rear panel of the product.

• This product is for indoor use only! (IP20) To prevent risk of fire or

shock, do not expose this product to rain or moisture.

• Always mount this product in a location with adequate ventilation, at

least 20 in (50 cm) from adjacent surfaces.

• Be sure that no ventilation slots on the unit’s housing are blocked.

• Never connect this product to a dimmer or rheostat.

• Replace the fuse with the same type and rating.

• ONLY use the hanging/mounting bracket or the handles to carry this

product.

• The maximum ambient temperature is 104° F (40° C). Do not operate

this product at higher temperatures.

• In the event of a serious operating problem, stop using immediately.

•

DO NOT open this product. It contains no user-serviceable parts.

Contact

Outside the U.S., United Kingdom, or Ireland, contact your distributor to

request support or return a product. Visit www.chauvetlighting.com

for

contact information.

EN SlimPACK™ 56 QRG

3

What Is

Included

• 4 SlimPAR™ 56

• 1 Obey™ 3

• 4 DMX Cables

• Power Cords

• 1 Carry Bag

• 1 Warranty Card

• 1 Quick Reference Guide

To Begin

Unpack your SlimPACK™ 56 and

make sure you have received all parts in

good condition. If the box or contents appear damaged, notify the carrier

immediately, not CHAUVET®.

Product

Description

The SlimPACK™ 56 package includes four SlimPAR™ 56 lights, one

Obey™ 3 controller, four 10-foot DMX cables, and a CHS-SP4 carry bag.

The SlimPAR™ 56 is a compact, low-

profile LED par that can be used

when a compact wash is needed because it fits where other lights cannot.

With automated programs and power linking for autonomous operation, the

SlimPAR™ 56 works great for quiet installations due to silent operation

and lack of moving parts.

The Obey™ 3 is a compact DMX-512 controller for LED fixtures that

includes preset, chase, and macro modes. You will have full control of your

light show with

full fader and blackout control, and adjustable audio

sensitivity.

The CHS-SP4 holds accessories for the entertainer on the go. The soft bag

is custom-

designed to carry the SlimPAR™ 56s, the Obey™ 3, and all

connecting cables. Five internal padded compart

ments and two external

components allow quick, safe, and easy access to your lights.

SlimPAR™ 56

Overview

Fuse holder

Satellite™ Power In

Microphone

Control Panel

(LED Display)

Microphone Adjustment Knob

Bracket

Adjustment

Knob

Power In

Power Out

DMX Out

DMX In

SlimPACK™ 56 QRG EN

4

Obey™ 3

Overview

AC Power

The SlimPAR™ 56 has an auto-

ranging power supply that can work with an

input voltage range of 100~240 VAC, 50/60 Hz.

The Obey™ 3 runs on a 12 VDC, 500 mA external power supply.

Power Linking

You can link up to 50 SlimPAR™ 56 units at 120 VAC, and 100 units at 230

VAC. You should never exceed this number.

Fuse

Replacement

(SlimPAR™ 56

only)

1. Disconnect this product from the power outlet.

2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder

and pry the safety cap out of its housing. The safety cap will pull the

installed fuse with it.

3.

Remove the blown fuse from the safety cap and replace with a fuse of the

exact same type and rating.

4. Insert the fuse holder back in its place, and reconnect power.

Sound Sensitivity

Adjustment Knob

Preset Button

Fade/Speed/Strobe/Green Fader

Chases/Macro/Red Fader

Strobe Button

Sound Button

Blackout Button

Manual RGB Button

Chases Button

Macro Button

Master Dimmer/Blue Fader

Power On/Off

Switch

12 VDC Input

DMX Out

Back Panel

EN SlimPACK™ 56 QRG

5

Mounting

Before mounting this product, read the Safety Notes at the beginning of this

guide and in the product’s User Manual. The mounting instructions are

provided in Setup in the User Manual.

Product

Mounting

Diagram

Programming

For details on how to fully program these products, please refer to the

applicable product’s User Manual.

DMX Linking

The SlimPAR™ 56

can work with a DMX controller when linked using a

regular DMX serial connection. If you are not familiar with DMX,

download the DMX Primer from www.chauvetlighting.com.

DMX Connection

The SlimPAR™ 56 uses a

regular DMX data connection for its DMX

personalities, 7-CH and 3-CH.

Download the SlimPAR™ 56 User Manual and refer to Setup

to learn how

to connect this product for DMX operation, and Operation

to learn in detail

how to configure this product for DMX operation.

Master/Slave

Connection

The SlimPAR™ 56

uses the DMX data connection for its Master/Slave

mode.

Download the SlimPAR™ 56 User Manual and refer to Setup

to learn how

to connect this product for Master/Slave operation, and Operation to

learn in

detail how to configure this product for Master/Slave operation.

Secondary Bracket

Primary Bracket

Bracket Adjustment Knob

SlimPACK™ 56 QRG EN

6

Connections

Diagram

For easy setup, use the following diagrams to physically connect your

SlimPAR™ 56 units to the Obey™ 3 and each other.

Power linking setup

To additional

SlimPAR™ 56s

To additional

SlimPAR™ 56s

DMX setup

EN SlimPACK™ 56 QRG

7

Menu

Configuration

(SlimPAR™ 56)

In order for your SlimPACK™ 56 to work properly, all the SlimPAR

™ 56

lights must be configured correctly. Follow the steps below to configure your

SlimPACK™ 56.

1. Press the <MENU> button on the SlimPAR

™ 56 until d001 shows.

2. Press <UP> or <DOWN> to set the starting address to 001.

3. Press <ENTER>.

4. Repeat the steps for each SlimPAR™ 56 in the configuration.

Every SlimPAR™ 56 in the configuration must be in 3-CH mode to

function

properly with the Obey™ 3 controller. The lights will not react

to the controller’s input if they are in 7-CH mode.

Obey™ 3 Basic

Operation:

(Preset Colors)

1. Press the <BLACKOUT> button to disable the blackout function (LED

indicator OFF).

2. Slide the <FADE TIME> fader (middle) and the <DIMMER FADER>

(right) all the way up to turn on.

3. Press the <PRESET> button to illuminate the LED indicator above the

button.

4. Press one of the 9 preset color buttons to select a color.

5. Slide the <FADE TIME> fader (middle) to adjust the amount of time to

change from one color to another color.

6. To add a strobe, press the <STROBE>

button to illuminate the LED next

to it, then slide the <SPEED TIME> fader (middle) to the required strobe

rate. Press the <STROBE> button again to deactivate the strobe button

from the middle fader.

To stop the strobe effect, make sure you are in Strobe mode. Slide the

middle fader all the way down. Press the <STROBE> button to

deactivate the function from the middle fader.

Obey™ 3

Miscellaneous

Notes

• In <CHASES> and <MACRO> and <PRESET> operating modes, the

<DIMMER> fader (right) must be set at the top to see full output from

the lights. Set this fader down to adjust the master intensity of all

connected lights.

• The <CHASES> and <MACRO> buttons on the

lower left work with all

three faders.

• Pressing the <BLACKOUT> button will turn off the output of the lights,

and will also work with the <FADE TIME> fader (middle).

• The Obey™ 3 is designed to be used with 3-channel, red/green/blue

fixtures.

Page is loading ...

SlimPACK™ 56 QRG Multi-Language

52

Contact Us

World Headquarters

CHAUVET®

General Information

Address: 5200 NW 108th Avenue

Sunrise, FL 33351

Voice: (954) 929-1115

Fax: (954) 929-5560

Toll free: (800) 762-1084

United Kingdom and Ireland

CHAUVET® Europe Ltd.

General Information

Address: Unit 1C

Brookhill Road Industrial Estate

Pinxton, Nottingham, UK

NG16 6NT

Voice: +44 (0)1773 511115

Fax: +44 (0)1773 511110

Technical Support

Voice: (954) 929-1115 (Press 4)

Fax: (954) 756-8015

Email: tech@chauvetlighting.com

Technical Support

Email: uktech@chauvetlighting.com

World Wide Web

www.chauvetlighting.com

World Wide Web

www.chauvetlighting.co.uk

SlimPACK™ 56

QRG – Rev. 4 ML

Printed in the P. R. C.

CHAUVET DJ SlimPACK 56 LT Reference guide

This manual is also suitable for

CHAUVET DJ SlimPACK 56 LT Reference guide

in other languages

Related papers

Other documents