Toshiba DMF82XKU User guide

Digital Media Frame

OWNER’S MANUAL

Owner’s Record

The model number and serial number are on the back

of your Digital Media Frame. Record these numbers in

the spaces below. Refer to these numbers whenever

you communicate with your Toshiba dealer about this

Digital Media Frame.

Model number:

Serial number:

DMF102XKU

DMF82XKU

DMF82XWU

3

SAFETY

PRECAUTIONS

WARNING: Handling the cord on this product

or cords associated with accessories sold

with this product, will expose you to lead, a

chemical known to the State of California

to cause birth defects or other reproductive

harm. Wash hands after handling.

FCC NOTICE

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reason-

able protection against harmful interference in

a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the

user is encouraged to try to correct the

interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the

equipment and receiver.

- Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced

radio/TV technician for help.

WARNING: Only peripherals complying with

the FCC class B limits may be attached to

this equipment. Operation with non-compliant

peripherals or peripherals not recommended

by Toshiba is likely to result in interference

to radio and TV reception. Shielded cables

must be used between the external devices

and the Universal Serial Bus (USB 2.0) ports.

Changes or modifications made to this equip-

ment, not expressly approved by Toshiba, or

parties authorized by Toshiba, could void the

user’s authority to operate the equipment.

This device complies with part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful

interference, and

(2) this device must accept any interference

received, including interference that may

cause undesired operation.

Responsible party:

Toshiba America Consumer Products, L.L.C.

82 Totowa Rd.; Wayne, N.J.07470

Phone: (800) 631-3811

CAUTION: These servicing instructions

are for use by qualified service personnel

only. To reduce the risk of electric shock do

not perform any servicing other than that

contained in the operating instructions unless

you are qualified to do so.

FCC Radiation Exposure Statement

This transmitter complies with the FCC

radiation exposure limits as set forth for the

general population/uncontrolled environment.

To comply, or maintain compliance, with the

FCC RF exposure requirements, no change

to the antenna or the device is permitted.

Any changes to the antenna or the device

could result in the device exceeding the RF

exposure requirements and would void user

authorization to operate the equipment. In ad-

dition, this transmitter must not be co-located

or operating in conjunction with any other

antenna or transmitter.

IMPORTANT SAFETY

INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not install near any heat sources such

as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

8. Do not block any ventilation openings.

Install in accordance with the manufacturer’s

instructions.

9. Do not insert any foreign objects into the

memory card slot. Heat build-up or fire may

result.

4

19. Do not place a vessel containing liquid

(such as a vase), or a metal object on top

of the apparatus. Fire or Electric shock may

result if liquid or metal objects enter the

apparatus.

20. Do not rest the product on your lap or

other parts of body. The product may become

warm during use. Even low temperatures may

cause personal injury when exposed to your

skin for prolonged periods.

21. Use the supplied AC adaptor to operate

the product. Substitute devices not specified

by the manufacturer may result in fire or

product malfunction. Do not cover the AC

adaptor with a blanket or place it near heating

or on electric carpet when it is in use.

22. WARNING: To prevent the spread of fire,

keep candles or other open flames away from

this product at all times.

23. CAUTION: If the digital media frame is

dropped and the cabinet or enclosure surface

has been damaged or the digital media frame

does not operate normally, take the following

precautions:

● ALWAYS turn off the digital media frame

and unplug the AC adaptor to avoid possible

electric shock or fire.

● NEVER allow your body to come in contact

with any broken glass or liquid from the

damaged digital media frame. The LCD

panel inside the digital media frame contains

glass and a toxic liquid. If the liquid comes in

contact with your mouth or eyes, or your skin

is cut by broken glass, rinse the affected area

thoroughly with water and consult your doctor.

● ALWAYS contact a service technician to

inspect the digital media frame any time it has

been damaged or dropped.

24. Use the digital media frame in a location

that facilitates the immediate removal of the

plug if there is a malfunction or failure.

25. Do not allow children to scratch, lick or

put the memory card into their mouth. Keep

the memory card out of the reach of children.

Injury to the child or malfunction may result.

26. Should you ever notice a strange odor,

smoke, or excessive heat coming from the

digital media frame, remove the AC adaptor.

Continued use in this state might cause fire,

electric shock, or burns. For details on repair,

consult Toshiba Customer Service.

27. Coin-shaped Battery

a) CAUTION: Danger of explosion if battery

is incorrectly replaced. Replace only with the

same or equivalent type.

10. Protect the power cord from being

walked on or pinched particularly at plugs,

convenience receptacles, and the point where

they exit from the apparatus.

11. Do not defeat the safety purpose of the

polarized or grounding-type plug. A polarized

plug has two blades with one wider than the

other. A grounding type plug has two blades

and a third grounding prong. The wide blade

or the prong are provided for your safety. If

the provided plug does not fit into your outlet,

consult an electrician for replacement of the

obsolete outlet.

12. Only use attachments/accessories

specified by the manufacturer.

13. Unplug this apparatus during lightning

storms or when unused for long periods

of time. However, while it is thundering or

lightning, do not touch the apparatus and any

connected cable and/or equipment. This will

prevent you from receiving the electric shock

by an electric surge.

14. Refer all servicing to qualified service

personnel. Servicing is required when the ap-

paratus has been damaged in any way, such

as power-supply cord or plug is damaged,

liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate

normally, or has been dropped.

15. Use only cart, stand, tripod bracket

or table specified by the manufacturer or

sold with the product. When a cart is used,

operate carefully to prevent the objects from

tip-over.

ADDITIONAL SAFETY INSTRUCTIONS

16. When you use headphones, keep the

volume at a moderate level. Using head-

phones continuously with high volume levels

may permanently damage your hearing.

17. Do not overload wall outlets; extension

cords, or integral convenience receptacles as

this can result in a risk of fire or electric shock.

18. Apparatus shall not be exposed to

dripping or splashing and no objects filled with

liquids, such as vases, shall be placed on the

apparatus and/or around it.

5

b) The remote control battery contains

Perchlorate Material - special handling may

apply. See www.dtsc.ca.gov/hazardouswaste/

perchlorate

c) Keep coin-shaped batteries out of

children’s reach. Be careful not to ingest

internally, especially by children, as doing so

may cause poisoning.

d) Do not install the battery backwards. Fol-

low the instructions for battery replacement.

e) Do not charge, heat, open, or short-circuit

the batteries. Do not throw the batteries into

a fire.

f) Do not leave a dead or exhausted battery in

the remote control.

g) If you do not use the remote control for

a long period of time, remove the battery

to avoid possible damage from battery

corrosion.

28. After unpacking coin-shaped batteries,

store them in poly bags, etc. separately one

by one when unused. If you leave them

unwrapped, they may be short-circuited by

contact with metal objects, resulting in battery

leakage, heat or bursting. This may cause

burns or injury. The batteries must be com-

pletely discharged when they are deposited

in collection containers for old batteries. If a

charge remains, countermeasures to prevent

short circuits must be taken.

29. To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or

moisture.

30. Following mark means “CAUTION - RISK

OF ELECTRIC SHOCK - DO NOT OPEN”.

The lighting ﬂash with arrowhead

symbol, within an equilateral tri-

angle, is intended to alert the user

to the presence of uninsulated

‘dangerous voltage’ within the

product enclosure that may be of

sufﬁcient magnitude constitute a

risk of electric shock to humans.

The exclamation point within an

equilateral triangle is intended to

alert the user to the presence of

important operating and mainte-

nance (servicing) instructions in

the literature accompanying the

appliance.

31. Wireless Communication

a) Turn off the digital media frame power in

locations where a person using a pacemaker

may be present nearby.

The radio waves generated by the product

may affect the operation of the pacemaker.

b) Keep the product away from the location of

the pacemaker by at least 22 cm.

The radio waves generated by the product

may affect the operation of the pacemaker.

c) Turn off the digital media frame power

inside hospitals and other medical facilities or

near electrically operated medical equipment.

The radio waves generated by the product

may negatively affect medical equipment,

causing malfunction and eventual accident.

d) Turn off the digital media frame power

near automatic doors, fire alarms and other

automatic control equipment.

The radio waves generated by the product

may negatively affect such equipment,

causing malfunction and eventual accident.

e) Turn off the digital media frame power

on airplanes or in other locations where the

product may cause radio interference.

The radio waves generated by the product

may negatively affect equipment, causing

malfunction and eventual accident. For

details, follow the instructions given by each

airline.

f) If any nearby equipment experienced radio

interference or any other problem when the

digital media frame is used, turn off the digital

media frame power.

The radio waves generated by the product

may negatively affect nearby equipment,

causing malfunction and eventual accident.

PRECAUTIONS

NOTES ON HANDLING

● Do not shock the LCD screen. It may cause

unit damage and malfunction.

● When transporting the digital media frame,

the original shipping carton and packing

materials come in handy. For maximum

protection, repack the unit as it was originally

packaged at the factory.

6

● Do not use volatile liquids, such as insect

spray, near the digital media frame. Do not

leave rubber or plastic products in contact

with the digital media frame for a long time.

They will leave marks on the ﬁnish.

● When the digital media frame is not in use,

be sure to turn off the power.

● If you do not use the digital media frame

for a long period, the unit may not function

properly in the future. Turn on and use the

digital media frame occasionally.

NOTES ON LOCATING

● When you place this digital media frame

near a TV, radio, or VCR, the playback picture

may become poor and the sound may be

distorted. In this case, move the digital media

frame away from the TV, radio, or VCR.

NOTES ON CLEANING

● Use a soft, dry cloth for cleaning. Do not

use any type of solvent, such as thinner and

benzine, as they may damage the surface of

the digital media frame.

● When cleaning the LCD screen, use a soft,

dry cloth.

NOTES ON MOISTURE CONDENSATION

Moisture condensation damages the

digital media frame. Please read the

following carefully.

Moisture condensation occurs, for example,

when you pour a cold drink into a glass on a

warm day. Drops of water form on the outside

of the glass. In the same way, moisture may

condense on the internal parts of the digital

media frame.

● Moisture condensation occurs during the

following cases.

- When you transport the digital media frame

directly from a cold place to a warm place.

- When you use the digital media frame in a

room where you just turned on the heater,

or a place where the cold air from the air

conditioner directly hits the unit.

- In summer, when you use the digital media

frame in a hot and humid place just after you

move the unit from an air conditioned room.

- When you use the digital media frame in a

humid place.

● Do not use the digital media frame when

moisture condensation may occur.

If you use the digital media frame in such

a situation, it may damage memory cards

and internal parts. Remove the memory

cards, connect the AC adaptor, turn on the

digital media frame, and leave it for two or

three hours. After two or three hours, the

digital media frame will have warmed up and

evaporated any moisture.

ABOUT DATA

● The contents in the memory storage

(internal memory, memory card, USB memory

device) cannot be guaranteed regardless of

the cause of damage or failure.

● Please note that data in the internal

memory may be deleted when repairing or

checking the Digital Media Frame.

WIRELESS LAN

INFORMATION

Wireless Interoperability

This product is designed to be interoperable

with any wireless LAN product that is based

on Direct Sequence Spread Spectrum

(DSSS)/Orthogonal Frequency Division

Multiplexing(OFDM) radio technology, and is

compliant to:

■ The IEEE 802.11 Standard on Wireless

LANs (Revision B/G), as deﬁned and

approved by the Institute of Electrical and

Electronics Engineers.

■ The Wireless Fidelity (Wi-Fi) certiﬁcation

as deﬁned by the Wi-Fi Alliance. The “Wi-Fi

CERTIFIED” logo is a certiﬁcation mark of the

Wi-Fi Alliance.

CAUTION

Bluetooth® and Wireless LAN devices oper-

ate within the same radio frequency range

and may interfere with one another. If you use

Bluetooth and Wireless LAN devices simul-

taneously, you may occasionally experience

a less than optimal network performance or

even lose your network connection.

If you should experience any such problem,

immediately turn off either one of your

Bluetooth or Wireless LAN.

7

Wireless LAN and your Health

Wireless LAN products, like other radio

devices, emit radio frequency electromag-

netic energy. The level of energy emitted by

Wireless LAN devices however is far much

less than the electromagnetic energy emitted

by wireless devices like for example mobile

phones.

Because Wireless LAN products operate

within the guidelines found in radio frequency

safety standards and recommendations,

TOSHIBA believes Wireless LAN is safe for

use by consumers. These standards and

recommendations reﬂect the consensus

of the scientiﬁc community and result from

deliberations of panels and committees of

scientists who continually review and interpret

the extensive research literature.

In some situations or environments, the

use of Wireless LAN may be restricted by

the proprietor of the building or responsible

representatives of the organization. These

situations may for example include:

■ Using the Wireless LAN equipment on

board of airplanes, or

■ In any other environment where the risk of

interference to other devices or services is

perceived or identiﬁed as harmful.

If you are uncertain of the policy that applies

on the use of wireless devices in a speciﬁc

organization or environment (e.g. airports),

you are encouraged to ask for authorization to

use the Wireless LAN device prior to turning

on the equipment.

8

• Safety Precautions ................................................................................................... 3

• Important Safety Instructions ................................................................................. 3

• Precautions ............................................................................................................... 5

• Wireless LAN Information ........................................................................................ 6

MEDIA FRAME OVERVIEW 11

• Accessories ........................................................................................................... 11

• Front View ............................................................................................................. 12

• Rear View .............................................................................................................. 13

• Side View ............................................................................................................... 14

• Remote Control ..................................................................................................... 15

• Getting Started ...................................................................................................... 16

Installing The Stand ...................................................................................................... 16

Placing The Media Frame .............................................................................................. 16

Using The Remote Control ............................................................................................. 17

Connecting to Power ..................................................................................................... 18

Inserting/Connecting Devices ....................................................................................... 19

Connecting to A Computer ........................................................................................... 21

Connecting Headphones ................................................................................................ 21

• Mode Menu ............................................................................................................ 22

USING THE MEDIA FRAME 23

• Viewing Photos ...................................................................................................... 23

Slideshow Mode ............................................................................................................ 23

Single Photo Mode ........................................................................................................ 24

• Watching Videos .................................................................................................... 25

• Playing Music ......................................................................................................... 26

• Displaying The Clock ............................................................................................. 27

• Displaying The Calendar ........................................................................................ 28

• Changing Display Style .......................................................................................... 29

• Displaying Thumbnail ............................................................................................ 29

• Viewing The Demo ................................................................................................. 30

• Copying Files ......................................................................................................... 31

Copying One File .......................................................................................................... 31

Copying Multiple Files ................................................................................................... 32

CONTENTS

• Deleting Files ..........................................................................................................33

Deleting One File ...........................................................................................................33

Deleting Multiple Files ....................................................................................................33

• Connecting to A Computer .....................................................................................34

Copying from A Computer ..............................................................................................35

USING ONLINE SERVICES 37

• Setting Up A Wireless Network ..............................................................................37

Wi-Fi Settings: Auto Configuration ..................................................................................37

Wi-Fi Settings: Manual Configuration ..............................................................................39

Wi-Fi Settings: IP Settings ..............................................................................................41

• Using FrameChannel

®

..............................................................................................42

Registering with FrameChannel ........................................................................................42

Using FrameChannel .......................................................................................................43

• Using Google

®

Picasa™ ............................................................................................44

Registering with Google Picasa ........................................................................................44

Using Google Picasa ........................................................................................................45

SETTINGS 47

• Menu Overview .......................................................................................................47

• Modifying Viewing Settings ....................................................................................49

Screen Settings .............................................................................................................49

Photo Display Order .......................................................................................................49

Slideshow Settings .........................................................................................................50

Display Mode .................................................................................................................50

• Modifying System Settings .....................................................................................50

Language ......................................................................................................................51

Date/Time Settings .......................................................................................................51

File Access Level ............................................................................................................52

Key Sound ....................................................................................................................52

System Manager ............................................................................................................52

• Selecting Devices ...................................................................................................53

• Modifying Network Settings ...................................................................................54

Wi-Fi Settings ................................................................................................................54

Online Service Settings ...................................................................................................54

SPECIFICATIONS 55

TROUBLESHOOTING 59

LIMITED WARRANTY 63

APPENDIX 65

MEDIA FRAME OVERVIEW

ACCESSORIES

Thank you for purchasing the Toshiba

Digital Media Frame. Please check

whether all the following items are

included in your box.

□ Digital Media Frame x 1

□ Stand x 1

□ Rubber Supporter x 1

□ Remote Control (SE-R0351) x 1

□ AC Adaptor x 1

□ Setup Guide x 2

(English & Spanish)

□ Important Information x 1

NOTES AND INFORMATION

TRADEMARKS

▪ FrameChannel® is a registered trade-

mark of Frame Media, Inc.

▪ Picasa™ and the Picasa logo are

trademarks

▪ Wi-Fi®, Wi-Fi Alliance®, Wi-Fi Protected

Access (WPA)® and the Wi-Fi CERTI-

FIED logo are registered trademarks of

the Wi-Fi Alliance. Wi-Fi CERTIFIED™

and Wi-Fi Protected Setup™ are

trademarks of the Wi-Fi Alliance.

▪ “Memory Stick”, “Memory Stick Duo”,

“Memory Stick PRO”, “Memory Stick PRO

Duo” and “Memory Stick PRO-HG Duo”

are trademarks or registered trademarks

of Sony Corporation.

▪ xD-Picture Card™ is a trademark of

FUJIFILM Corporation.

▪ MultiMediaCard is a trademark of

Inﬁ neon Technologies AG.

▪ Windows, Windows Vista, Windows Me-

dia, Windows Media logo are registered

trademarks or trademarks of Microsoft

Corporation in the United States and/or

other countries.

▪ Macintosh is a registered trademark of

Apple Inc.

▪ Bluetooth is a registered trademark of

Bluetooth SIG, Inc.

All other brand and product names are

trademarks or registered trademarks of

their respective companies.

COPYRIGHTS

The data you have recorded must be

used for your own personal enjoyment.

The unauthorized recording, use, distribu-

tion, or revision of copyrighted materials

including, without limitation, television

programs, videotapes, and DVDs, is

prohibited under the Copyright Laws of

the United States and other countries,

and may subject you to civil and criminal

liability.

▪ THIS PRODUCT IS LICENSED UNDER

THE MPEG-4 VISUAL PATENT PORTFORIO

LICENSE FOR THE PERSONAL AND

NON-COMMERCIAL USE OF A CONSUMER

FOR (i) ENCODING VIDEO IN COMPLIANCE

WITH THE MPEG-4 VISUAL STANDARD

(“MPEG-4 VIDEO”) AND/OR (ii) DECODING

MPEG-4 VIDEO THAT WAS ENCODED BY

A CONSUMER ENGAGED IN A PERSONAL

AND NON-COMMERCIAL ACTIVITY AND/OR

WAS OBTAINED FROM A VIDEO PROVIDER

LICENSED BY MPEG LA TO PROVIDE

MPEG-4 VIDEO. NO LICENSE IS GRANTED

OR SHALL BE IMPLIED FOR ANY OTHER

USE. ADDITIONAL INFORMATION INCLUD-

ING THAT RELATING TO PROMOTIONAL,

INTERNAL AND COMMERCIAL USES AND

LICENSING MAY BE OBTAINED FROM MPEG

LA, L.L.C. SEE HTTP//WWW.MPEGLA.COM

▪ MPEG Layer-3 audio coding technol-

ogy licensed from Fraunhofer LLS and

Thomson.

MEDIA FRAME OVERVIEW12

TOUCH CONTROL KEYS

The Toshiba Digital Media Frame is

designed with touch key technology.

You can control the Digital Media Frame

by touching the designated keys on the

right side of the screen. The function

keys will light up when touched.

MODE

MENU

BACK

ENTER











 MODE: Touch to display the Mode

screen

 MENU: Touch to display the Menu

screen

 ▲▼◄►: Touch to move the cursor

towards desired direction (In the

music or video playback mode,

press ▲▼ to control the volume.)

 ENTER: Touch to confirm

selection

 BACK: Touch to return to the

previous option

NOTE

♦ If the touch control keys are not used,

the key display disappears in a few

seconds.

♦ Do not press the touch keys with

force.

FRONT VIEW







 LCD Screen

 Remote Control Sensor

 Touch Control Keys

ABOUT THE LCD

● The LCD panel contained in this

product is manufactured using an

extremely high level of precision

technology; however, there may be

an occasional pixel (dot of light) that

does not operate properly (does not

light, remains constantly lit, etc.).

This is a structural property of LCD

technology, is not a sign of malfunc-

tion, and is not covered under your

warranty. Such pixels are not visible

when the picture is viewed from a

normal viewing distance

● The brightness of the LCD screen

differs slightly depending on the

viewing angles.

MEDIA FRAME OVERVIEW 13

DMF102X









 Stand

 Speakers

 Wall-Mounting Holes

 Rubber Supporter

REAR VIEW

DMF82X







 Stand

 Speakers

 Rubber Supporter

MEDIA FRAME OVERVIEW14









 Headphone Jack

 PC Port (USB Mini-B)

 USB Port

 DC IN 12V Jack

SIDE VIEW









 Power Button

 SD/MMC/xD Card Slot

 MS/MS Duo Card Slot

 WPS Button

TO HANG THIS PRODUCT ON A WALL

● Be sure to use the screws appropriate for the material and strength of the wall.

● Toshiba does not take any responsibility for any accident or damage caused by

the failure to hang the Digital Media Frame on a wall properly.

MEDIA FRAME OVERVIEW 15

REMOTE CONTROL

 ROTATE : Press to rotate a

photo. (Refer to page 24)

 ON/STANDBY: Press to turn

on/off the Digital Media Frame.

(Refer to page 18 )

 SLIDESHOW: Press to start

photo slideshow. (Refer to page 23 )

 CLOCK/CALENDAR: Press to

display Clock/Calendar or to switch

between the two modes. (Refer to

page 27, 28 )

 STYLE: Press to (1) change

slideshow style during slideshow

playback (2) change clock style in

Clock mode (3) change calendar

style in Calendar mode. (Refer to

page 29 )

 THUMBNAIL: Press to display

photo/video files in thumbnail view

or music files in list view. (Refer to

page 29 )

 ZOOM OUT: Press to zoom out

of a photo. (On the file browser

screen, press the button to reduce

the size of a thumbnail picture.)

(Refer to page 24 )

 ZOOM IN: Press to zoom in a

photo. (On the file browser screen,

press the button to increase the size

of a thumbnail picture.) (Refer to

page 24 )

 MENU: Press to display the Menu

screen. Press again to close the

Menu screen. (Refer to page 49, 50,

53, 54 )

 ▲▼◄►: Press to move the cursor

towards desired direction. (In the

music or video playback mode,

press ▲▼ to control the volume.)

MODE: Press to display the Mode

screen. (Refer to page 22)

ENTER/



: Press to confirm

selection or to pause photo/video/

music file playback.

BACK: Press to return to the

previous option.

OPTION: Press to display available

options. (Refer to page 24, 25, 26,

31, 32, 33)

MEDIA FRAME OVERVIEW16

GETTING STARTED

INSTALLING THE STAND

Attach the supplied stand as illustrated.

Stand

NOTE

♦ Do not hold the stand when carrying

the Digital Media Frame.

PLACING THE MEDIA

FRAME

1 Slide the Digital Media Frame into

the slot of the rubber supporter as

illustrated.

Rubber Supporter

2 Make sure the Digital Media Frame

is stably placed.

NOTE

♦ The Digital Media Frame can be

placed vertically.

♦ If this product is placed vertically, the

angle of the displayed photo will change

accordingly. This feature does not apply

to video playback.

MEDIA FRAME OVERVIEW 17

USING THE REMOTE

CONTROL

■

Preparing the Remote

Control

Remove the transparent slip (as

illustrated) before using the remote

control.

Transparent Slip

■

Operating with the Remote

Control

Point the remote control at the remote

sensor and press the buttons.

Within about 5 m (16 feet)

MODE

MENU

BACK

ENTER

22.5 22.5

Distance: About 5 m (16 feet) from the

front of the remote sensor.

Angle: About 22.5° in each direction of

the front of the remote sensor.

Do not expose the remote sensor of

the Digital Media Frame to a strong

light source such as direct sunlight. If

you do, you may not be able to operate

the Digital Media Frame via the remote

control.

• Do not drop or give the remote

control a shock.

• Do not leave the remote control near

an extremely hot or humid place.

• Do not spill water or put anything wet

on the remote control.

• Do not disassemble the remote

control.

• If the remote control does not func-

tion correctly or if the operating range

becomes reduced, replace the battery

with new one.

• Inserting a battery other than the

specified one or an object may damage

the remote control.

■

Replacing the Remote Con-

trol Battery

Insert the speciﬁ ed battery into the

remote control. (*Please see page 4 for

safe use of coin-shaped batteries.)

1 Push the battery compartment lid

slightly in the direction illustrated.

2 Gently insert a fingernail in groove.

3 Pull out the holder in the direction

illustrated. (*Take care not to break your

fingernail.)









PUSH

OPEN

MEDIA FRAME OVERVIEW18

4 Remove the old battery.

5 Place a new coin-shaped battery

(CR2025) with the + side up on the

holder. Keep the holder horizontal so

that the battery does not fall through.

R2025

C

V3

CAUTION

♦ Danger of explosion if battery is

incorrectly replaced. Replace only with

the same or equivalent type.

6 Insert the holder into the remote

control.

The remote control battery contains

Perchlorate Material - special handling

may apply. See www.dtsc.ca.gov/

hazardouswaste/perchlorate.

CONNECTING TO POWER

1 Connect one end of the AC adaptor

to the Digital Media Frame.

2 Plug the other end of the AC adaptor

into the outlet.

AC Adaptor

■

Turning on the Digital Media

Frame

Press the POWER button (on the side

of the Digital Media Frame) or the

ON/STANDBY button (on the remote

control) to turn on the Digital Media

Frame. The power indicator will turn to

green.

CAUTION

♦ Do not connect the power plug to a

power outlet other than that indicated

on the label, as this can result in a risk

of ﬁ re or electric shock.

♦ Do not connect or disconnect the

power plug with wet hands. Doing so

may cause electric shock.

♦ Do not use an AC adaptor other than

one speciﬁ ed, as it can cause a ﬁ re or

damage to the Digital Media Frame.

MEDIA FRAME OVERVIEW 19

♦ When the AC adaptor is in use, its

temperature may increase. However,

it is not a malfunction. Make sure that

the AC adaptor is disconnected and the

temperature decreases before carrying

it.

NOTE

♦ Do not use the supplied AC adaptor

with any device other than this Digital

Media Frame.

♦ It takes some time when you turn on

the device by pressing the POWER

button (on the side of the Digital Media

Frame) for the ﬁ rst time.

■

To Switch Between Standby

Mode And Power-On Mode

1 Press the POWER button (on the

side of the Digital Media Frame) or the

ON/STANDBY button (on the remote

control) to turn on the device. The

power indicator will turn to green.

2 Press the button again to switch to

the Standby mode. The power indicator

will turn to red.

Power Indicator

(Center)

■

To Power Off

1 Press and hold the POWER button

(on the side of the Digital Media

Frame) for several seconds. The power

indicator goes out.

You can still use the ON/STANDBY

button during the power-off mode.

INSERTING/CONNECTING

DEVICES

■

Inserting Memory Card(s)

1 Insert the memory cards in direction

indicated (as illustrated) and slowly

push the cards to lock into place.

SD

xD

MS DUO

MS

■

Removing Memory Card(s)

1 Remove the memory cards slowly

from corresponding slots in direction

indicated (as illustrated).

SD

xD

MS DUO

MS

NOTE

♦ For details about the memory cards

supported, please refer to the section

Speciﬁ cations. (Refer to page 55)

MEDIA FRAME OVERVIEW20

NOTES ON MEMORY CARDS

Some memory cards may not be played

back due to its capacity and/or manu-

facturer, etc. Do not insert any memory

card other than those referred in the

‘Speciﬁcations’ chapter. Failure to follow

this instruction may cause a malfunction

of the digital media frame and/or card.

SAVING DATA

♦ It is recommended that you back up

your memory card data. Toshiba is not

liable for any damage caused by the

use of any memory card with this digital

media frame. Toshiba will not compen-

sate for any lost data or recording(s)

caused by the use of such cards.

♦ For instructions on using your memory

card, refer to the owner’s manual for

your memory card.

♦ Failure to take proper care of a

memory card may prevent the display of

pictures from the card. Such damage is

not covered by your Toshiba Warranty.

NOTICES FOR USE

♦ Ensure that you insert the memory

card correctly into this digital media

frame.

♦ Do not remove the memory card

while the Digital Media Frame is writing

or deleting data. Data saved on the

memory card may be lost.

♦ This memory card is a precision

electrical instrument. Do not bend, drop

or apply strong force to it.

♦ Do not use or store the memory card

in an environment of high static electric-

ity or electrical interference.

♦ Avoid using or storing in areas of high

temperature and humidity.

♦ Be careful not to touch with your ﬁn-

gers, nor allow foreign objects to come

in contact with nor dirt to accumulate on

the metal area (gold-colored area) of

the memory card. Wipe off any dirt with

a soft, dry cloth.

♦ When carrying or storing the

memory card always place it inside of

its antistatic case to avoid any effects

from static electricity. If there is a stor-

age case, place the memory card in the

antistatic area of the storage case.

♦ If you place a memory card that has

been exposed to static electricity in this

digital media frame, there is a chance

that this digital media frame could

malfunction.

♦ When ejecting the memory card after

extended use it may feel warm to the

touch. This is normal. The memory card

is not malfunctioning.

Page is loading ...

Toshiba DMF82XKU User guide

This manual is also suitable for

Toshiba DMF82XKU User guide

Related papers

Other documents