Real Fyre G18 is a gas log set that provides a realistic and ambiance to your home. It is designed for use with an R.H. Peterson Co. G18 burner and parts. The G18 is a vent-free gas log set, meaning that it does not require a chimney or flue. It is designed to be used in a fireplace or other enclosed space. The G18 comes with a variety of log styles to choose from, so you can find the perfect set to match your décor. The G18 is also available in a variety of sizes, so you can find the perfect fit for your fireplace.
Real Fyre G18 is a gas log set that provides a realistic and ambiance to your home. It is designed for use with an R.H. Peterson Co. G18 burner and parts. The G18 is a vent-free gas log set, meaning that it does not require a chimney or flue. It is designed to be used in a fireplace or other enclosed space. The G18 comes with a variety of log styles to choose from, so you can find the perfect set to match your décor. The G18 is also available in a variety of sizes, so you can find the perfect fit for your fireplace.
1
CAUTION...............WARNING...............IMPORTANT
USE ONLY A PETERSON REAL FYRE G18 BURNER WITH THIS REAL FYRE LOG SET.
Important: Adequate spacing between the
logs is NECESSARY and MUST be
maintained. If carbon build up (sooting)
exists, correct log placement before
sooting becomes worse. If any sooting
occurs outside of the fi rebox (i.e. on
the walls), turn off unit immediately
and contact a qualifi ed professional
service technician.
WARNING: Use ONLY a Peterson Real Fyre
G18 burner with this Real Fyre gas log
set. Failure to do so may result in
property damage or personal injury,
and will void listings, certifi cations,
and invalidate claims made to RHP.
Contact your local Real Fyre dealer if you
need more information.
This instruction contains log set placement for these Real Fyre logs. You must position and maintain the log
layout as shown here to ensure proper operation of the burner system. Incorrect log installation could cause
fl ame impingement and improper combustion, resulting in soot and/or excessive by-products of combustion.
DO NOT add any additional embers for this installation. Any additional embers will cause unsafe operation.
Use these logs only with a Peterson G18 burner system.
If you experience an accumulation of black carbon (soot) on your logs it is an indication of incomplete
combustion and you must correct the log placement as instructed in this manual. If signifi cant sooting
continues, stop using this gas log set.
Please read these instructions completely and carefully.
This product is only warranted when used as part of a
Robert H. Peterson Co. unvented burner system.
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
LOG SET IMPORTANT INFORMATION
L-F2-132REV 0 - 1904081345
EVENING FYRE & EVENING FYRE CHARRED LOG PLACEMENT INSTRUCTIONS
EFV-24 shown
2
Failure to use a Peterson G18 burner may result in a DANGEROUS
situation and in property damage, personal injury or even death, will void
listings and certifi cations, and will void any insurance coverage by R.H.
Peterson Co. or our insurers.
CAUTION: Burn hazard! Logs will remain hot for some time after use.
If you need to reposition any log to maintain the proper layout,
use heat resistant gloves or allow logs adequate time to cool
before handling.
WARNING: This gas log set is for use with an R.H. Peterson Co. G18
burner (and parts) ONLY.
L-F2-132REV 0 - 1904081345
3
EVENING FYRE & EVENING FYRE CHARRED LOG PLACEMENT INSTRUCTIONS (16/18" MODEL)
E(F,C)V-16/18
PARTS LIST
All items for this log set are included in one (1) box.
CAUTION: Burn hazard! Logs will remain hot
for some time after use.
The underside of the bottom logs have cutouts and tabs that align over the burner. THE BOTTOM LOGS
MUST BE FULLY SEATED ON THE BURNER. Certain logs have notches on them to allow for the logs to
interlock in place.
EFV-16/18 log set shown
III
I
II
I
I
Place the rear log (log #1) as shown. Slide it forward on the
burner, against the main burner bracket. ENSURE THE LOG
RESTS FLAT ON THE BURNER, AND THAT THE LEFT
BURNER BRACKET ALIGNS WITH THE GROOVE FOUND
ON THE FACE OF THE LOG.
1
2
Place the front log (log #2) as shown. The underside of the
log has two tabs that insert into the holes found on the burner.
ENSURE THE LOG RESTS FLAT ON THE BURNER.
III
Ensure the rear and front logs are snug up against the main
burner bracket.
Logs snug against bracket
Align notch
with bracket
Align tabs
with holes
1
2
EFVL-15BR
E(F,C)VL-18BF-2
3
EFVL-9T
4
5
E(F,C)VL-17TY
E(F,C)VL-12TL
CHK-6
6
CHK-7
7
IV
I
V
Place the left top log (log #3) as shown. The log should
lock in place over the logs below.
3
4
EVENING FYRE & EVENING FYRE CHARRED LOG PLACEMENT INSTRUCTIONS (16/18" MODEL) (CONT.)
V
After setting the logs into position as described above, ensure each is properly and fi rmly seated. The
vent-free gas log set will not function as intended if the logs are not correctly positioned. When placed
properly, the fl ames will not strike any portion of the logs. Periodically check the positioning of all logs to
ensure proper log placement and stability. If any fl ame is striking the logs, recheck log placement. Adjust
to conform with instructions. There should be no fl ame impingement on the logs.
V
Place the right top log (log #4) as shown. The log should
lock in place over the logs below.
4
Place the center top log (log #5) as shown. The log should
lock in place over the logs below.
5
VI
15 model shown
Side view
Front view
(place both sides)
1" (minimum)
Place the decorative wood chips in front of the burner. Ensure
the charred ends face inward. For the wood chip in front of the
valve, ensure at least 1" between it and the valve.
CAUTION: Ensure the wood chip in front of the valve
is at least 1" away from the valve to avoid
overheating and damage to the valve.
If this
minimum requirement of 1" clearance is
not possible, DO NOT use the wood chip.
CAUTION: THE WOOD CHIPS WILL BE HOT DURING AND
AFTER OPERATION.
6
Final Log Placement
VIIIVII
5
EVENING FYRE & EVENING FYRE CHARRED LOG PLACEMENT INSTRUCTIONS (24" & 30" MODELS)
The underside of the bottom logs have cutouts and tabs that align over the burner. THE BOTTOM LOGS
MUST BE FULLY SEATED ON THE BURNER. Certain logs have notches on them to allow for the logs to
interlock in place.
All items for this log set are included in one (1) box.
CAUTION: Burn hazard! Logs will remain hot
for some time after use.
1
2
Logs snug against bracket
3
4
Align
notch
with
bracket
Align tabs
with holes
III
III
IV
Place the rear log (log #1) as shown. Slide it forward on the
burner, against the main burner bracket. ENSURE THE LOG
RESTS FLAT ON THE BURNER, AND THAT THE LEFT
BURNER BRACKET ALIGNS WITH THE GROOVE FOUND
ON THE FACE OF THE LOG.
Place the front log (log #2) as shown. The underside of the
log has two tabs that insert into the holes found on the burner.
ENSURE THE LOG RESTS FLAT ON THE BURNER.
Ensure the rear and front logs are snug up against the main
burner bracket.
Place the left middle log (log #3) as shown. The log should
lock in place over the logs below.
Place the center middle log (log #4) as shown. The log should
lock in place over the logs below.
E(F,C)V-24 & E(F,C)V-30
PARTS LIST
EFV-24 log set shown
1
2
4
3
5
6
24" - EFVL-20BR-1
24" - ECVL-20BR
30" - EFVL-24BR-1
30" - ECVL-24BR
24" - E(F,C)VL-24BF-2
30" - E(F,C)VL-30BF-2
E(F,C)VL-12T
E(F,C)VL-10T
E(F,C)VL-13T
7
E(F,C)VL-13TY
E(F,C)VL-11TR
8
24" - CHK-6
30" - CHK-8
9
24" - CHK-7
30" - CHK-9
6
EVENING FYRE & EVENING FYRE CHARRED LOG PLACEMENT INSTRUCTIONS (24" & 30" MODELS) (CONT.)
5
6
7
V
VI
Place the right middle log (log #5) as shown. The log should
lock in place over the logs below.
Place the left top log (log #6) as shown. The log should lock
in place over the logs below.
Place the center top log (log #7) as shown. The log should
lock in place over the logs below.
VII
After setting the logs into position as described above, ensure each is properly and fi rmly seated. The
vent-free gas log set will not function as intended if the logs are not correctly positioned. When placed
properly, the fl ames will not strike any portion of the logs. Periodically check the positioning of all logs to
ensure proper log placement and stability. If any fl ame is striking the logs, recheck log placement. Adjust
to conform with instructions. There should be no fl ame impingement on the logs.
15 model shown
Side view
Front view
(place both sides)
1" (minimum)
Place the decorative wood chips in front of the burner. Ensure
the charred ends face inward. For the wood chip in front of
the valve, ensure at least 1" between it and the valve.
CAUTION: Ensure the wood chip in front of the
valve is at least 1" away from the valve
to avoid overheating and damage to the
valve. If this minimum requirement of
1" clearance is not possible, DO NOT
use the wood chip.
CAUTION: THE WOOD CHIPS WILL BE HOT DURING
AND AFTER OPERATION.
8
Final Log Placement
IX
VIII
-
1
-
2
-
3
-
4
-
5
-
6
Real Fyre G18 Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Real Fyre G18 is a gas log set that provides a realistic and ambiance to your home. It is designed for use with an R.H. Peterson Co. G18 burner and parts. The G18 is a vent-free gas log set, meaning that it does not require a chimney or flue. It is designed to be used in a fireplace or other enclosed space. The G18 comes with a variety of log styles to choose from, so you can find the perfect set to match your décor. The G18 is also available in a variety of sizes, so you can find the perfect fit for your fireplace.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Real Fyre G18 Owner's manual
-
-
-
-
-
-
-
-
-
