Wire
Cutters
Hammer
Test Pen 10mm
Wrench
10mm
Masonry Bit
Spirit Level
Wide
Cable Clamp
5 and 8 mm
Allen Keys
Recommended Tools
1. Mount the Ceiling Bracket
Mount the ceiling bracket using the 4 anchors
bolts and install the eye bolt for safety cable.
3. Secure Fan Assembly to the Ceiling
Bracket and Install Safety Cable
Lift the fan assembly and place it within the ceiling bracket.
Secure fan using the bolts and washers provided.
Secure the safety cable onto the eye bolt.
4. Securing the Hanger Tube
Adjust the hanger tube to be perpendicular to the
ground. Fully tighten the 2 upper hanger tube bolts to
secure the hanger tube.
5. Installing the Controller Box
Peel off the double-sided tape and secure the controller box
within the gap in the ceiling bracket in the orientation as seen
above. Ensure that the black antenna cable is hanging freely.
7. Unsecuring the Motor Cover
Remove the 5 inner screws followed by the 3 outer screws
to unsecure the motor cover. Lift and secure the motor to
expose the motor assembly.
8. Unsecure Fan Blade Mount Plate
Unsecure the upper fan blade mount
by removing the 5 screws.
DO NOT REMOVE THE LOWER FAN BLADE MOUNT!
Push the fan blade towards the motor and secure the fan
blade using the upper fan blade mount and the 5 screws.
Repeat this with the remaining fan blades.
9. Installing the Fan Blade
10. Repositioning the Motor Cover
Lower the motor cover ensuring a good fit.
NOTE THAT THE COLOUR POSITIONING
MARKERS ARE TO BE ALIGNED.
11. Securing the Motor Cover
To secure the motor cover, insert and tighten the 3
outer screws followed by the 5 inner screws
12. Earth Wire Connections
Located on one side of the mounting bracket,
connect the 3 Earth Wires with a screw to the
mounting bracket as seen in the image above.
13. Terminal Block Connections
On the other side of the mounting bracket, connect the
3-way connector, earth wire and mains power
connections as seen in the image above.
14. Terminal Block Connections - Image
The image above shows the connections for the terminal
block, earth wire and mains power connections.
15. Secure the Top Canopy
Raise the top canopy and secure it using
the screws on both sides of the canopy.
6. Installing the EMI Filter
Secure the EMI Filter Box as seen in the image above with
the cable tie provided, ensuring that the cable tie sits in
between the hanger tube bolts.
2. Connecting the Hanger Tube to Motor
With the hanger tube side marked ‘M’ connected to the
motor shaft, tighten the 2 bolts and 2 screws to secure the
assembly. Install and expand the safety split pins.
Installation Guide
v.1.31 Mar 2017
Distributor:
Khind Alliances Sdn. Bhd.
No. 2, Jalan Astaka U8/82, Bukit Jelutong,
40150 Shah Alam, Selangor, Malaysia.
Tel: +60 3 7839 2000
Fax: +60 3 7845 0300
Website : http://www.mistral.com.my/
Email : [email protected]
FAN FEATURES
CAUTIONS, SAFETY AND WARNINGS
Read the entire manual.
Ensure proper safety practices are followed.
Mark out a “no-crossing” area under the fan prior to installation.
It is the sole responsibility of the building owner and installer to ensure that the building
structure is sound, able to hold at least 4x the weight of the fan and that the mounting
system is properly installed.
To prevent a possible electrical shock, disconnect power to the fan when installing, servicing
or cleaning.
Fan installation and electrical connections should be done by a qualified installer and
electrician.
When drilling into the ceiling, ensure that hidden electrical wirings are not damaged.
All electrical controls are factory configured and no user adjustments are available.
Follow the wiring schematics to ensure proper operation.
Do not attempt to open or touch any of the electronics inside the control box as many of the
parts operate at live voltage.
Install the safety cable on EVERY fan.
Do not operate the fan if any part of it is damaged or appears damaged.
Do not attempt to open or repair any parts or components of the fan.
Do not bend or modify the fan blades in any way.
Repairs are strictly to be done by a qualified distributor or agent.
Leave this installation guide with the fan owner after the installation is complete. Please
keep this guide for future reference.
To prevent a light strobing effect caused by moving fan blades, please do not place fan
below lighting or skylights.
The minimum clearance of any lights (or similar obstruction) from tip of fan blade should
be at least 50cm.
The minimum distance from the tip of the fan blade to any wall, should not be less than
50cm. For optimal performance, it is recommended that this distance be greater than
100cm.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities or, lack of experience and knowledge unless under
supervision or instruction concerning use of the fan by a person responsible for their safety.
TECHNICAL SPECIFICATIONS
Light Switch
Speed Increase
FAN REMOTE CONTROLLER
Fan OFF
Fan ON
Timer
Rotation Winter/
Summer Mode
Speed Decrease
9-ft Mid-Size BLDC HVLS Fan
MCF-D108HVLS
MCF-D108HVLS Gloss White (1.0m hanger tube)
MCF-D108HVLS Matte Black (1.0m hanger tube)
/
