Technika LCD 40-270 User manual

LCD46-270

Full HD LCD TV with Freeview & USB Media Player

Model No

User Guide

IMPORTANT SAFETY INSTRUCTIONS

Please read these instructions. All the safety and operating instructions should be read before the

appliance is operated.

Warnings

• To reduce the risk of ﬁ re, electric shock or damage to the television, do not expose it to

dust, rain or moisture, or place any objects ﬁ lled with liquids on or near the television.

• Do not place the television in a conﬁ ned space, ensure that nothing can obstruct the

ventilation openings at the rear of the television.

• Dispose of this television and any components including batteries in an environmentally

friendly manner. If in doubt, please contact your local authority for details of recycling.

Safety

• For your safety, this appliance is ﬁ tted with a fused moulded 3 pin mains plug. Should

the fuse need to be replaced, ensure that any replacement is of the same amperage and

approved with the BSI mark.

• The television should be connected to a main socket outlet with a protective earthing connection.

• Never try and replace the mains plug unless you have adequate qualiﬁ cations and are

legally authorised to do so. In the event that a replacement Mains cable is required,

contact the manufacturer for a suitable replacement.

• Never use the television if it is damaged in any way.

• Always place the television on a ﬂ at level surface avoiding anywhere which may be subject

to strong vibration.

• Ensure the television is not placed on top of the power cable as the weight of the

television may damage the cable and cause a safety hazard.

• Never place mobile phones, speakers or any other device which may cause magnetic or

radio interference with the television. If interference is apparent, move the device causing

the interference away from the television.

• To disconnect the apparatus from the mains, please use the all pole mains switch located on the side,

underside or rear of the TV. The switch shall remain readily operable.

• Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine,

ﬁ re or the like.

• Install the product at least 5cm from the wall for ventilation.

Maintenance

• To clean this unit, wipe with a soft, dry cloth. If the surfaces are extremely dirty, use a

soft cloth dipped in a soap and water solution or a weak detergent solution.

• Use eyeglass cleaner to remove stubborn dirt from the LCD/LED Screen.

• Never use alcohol, paint thinner or benzene to clean this unit.

• Before using a chemically treated cloth, read the instructions that came with the cloth

carefully.

CAUTION: If water or other liquid enters the television through the display panel surface, a malfunction

may occur.

Packaging

• The safest way to transport your item is in the original box/packaging - please save your

packaging for this.

• You will need original box/packaging in the event of warranty/service repair or support. We are unable

to carry out warranty/service if you are unable to package it correctly.

To prevent spread of ﬁ re, keep candles or

other open ﬂ ames away from this product at all times

User Guide - Technika - LCD 46-270.indd Sec1:4User Guide - Technika - LCD 46-270.indd Sec1:4 13-Dec-11 4:42:53 PM13-Dec-11 4:42:53 PM

IMPORTANT SAFETY INSTRUCTIONS

Please read these instructions. All the safety and operating instructions should be read before the

appliance is operated.

Important Information Regarding Use of Video Games, Computers,

Captions or Other Fixed Image Displays

The extended use of ﬁ xed image program material can cause a permanent “shadow image” on the LCD

panel.

This background image is viewable on normal programs in the form of a stationary ﬁ xed image. This type

of irreversible LCD/LED panel deterioration can be limited by observing the following steps:

1. Reduce the brightness/contrast setting to a minimum viewing level.

2. Do not display the ﬁ xed image for extended periods of time.

3. Turn the power off when not in actual use.

Examples of images that you need to watch out for are as follows (this is not an exhaustive list):

• TV Channel Logos: e.g. Shopping channel logos and pricing displays-especially if they are

bright and stationary. Moving or low-contrast graphics are less likely to cause ageing of the screen.

• Time Displays

• Teletext: Do not view a stationary page for long period of time

• TV/DVD Menus: e.g. Listings of DVD disk content

• Pause Mode: Do not leave the TV in pause mode for long periods of time, e.g. When watching DVDs or

videos.

Important - Once ‘shadow image/screen burn’ occurs, it will never disappear and is not repairable under

warranty.

How do I dispose of this product?

UK: Waste electrical products should not be disposed of with household waste. Separate

disposal facilities exist. For your nearest facilities, please see www.recycle-more.co.uk or in

store for details.

ROI: Waste electrical products should not be disposed of with household waste. Separate

disposal facilities exist. Check with your Local Authority or retailer for recycling advice.

Batteries

• Observe the correct polarity when inserting batteries.

• Do not use different types of batteries together or mix old and new batteries.

• Dispose of batteries in an environmentally friendly way.

• Certain regions may regulate the disposal of batteries.

Please consult your local authority.

User Guide - Technika - LCD 46-270.indd Sec1:5User Guide - Technika - LCD 46-270.indd Sec1:5 13-Dec-11 4:42:53 PM13-Dec-11 4:42:53 PM

CONTENTS

Manufacturers Guarantee Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

What is included in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Attaching/Detaching the stand and wall mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10

Getting Started - Initial Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

TV Buttons and Input Source Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15

TV Menu Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-21

Channel Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Picture Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Sound Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Time Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Feature Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

PC Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23

7 Day TV Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

USB Mode / Media Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-30

Using your TV with a Sky digital set top box . . . . . . . . . . . . . . . . . . . . . . . . 26

Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Technical Speciﬁ cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

User Guide - Technika - LCD 46-270.indd Sec1:7User Guide - Technika - LCD 46-270.indd Sec1:7 13-Dec-11 4:42:53 PM13-Dec-11 4:42:53 PM

Please save your packaging as you will need this in the event of warranty/service repair or support. We

are unable to carry out warranty/service if you are unable to package it correctly. The safest way to

package your item in the event of warranty/service repair is in it’s original box/packaging.

WHAT IS INCLUDED IN THE BOX

Accessories

Included with this TV are the following accessories:

1 x User Guide

1 x Quick Start Guide

2 x AAA Batteries

1 x TV

1 x RF Cable

1 x Remote Control

What is included in the box

User Guide

Quick Start

Guide

1 x Stand plus screws

User Guide - Technika - LCD 46-270.indd Sec1:8User Guide - Technika - LCD 46-270.indd Sec1:8 13-Dec-11 4:42:53 PM13-Dec-11 4:42:53 PM

ATTACHING THE STAND

Attaching the stand

To complete stand installation you will need a Philips screwdriver.

Insert the base into the neck of the stand and secure with the screws provided

User Guide - Technika - LCD 46-270.indd Sec1:9User Guide - Technika - LCD 46-270.indd Sec1:9 13-Dec-11 4:42:56 PM13-Dec-11 4:42:56 PM

DETACHING THE STAND

Detaching the Stand

1) Remove the screws highlighted

IMPORTANT - Before drilling any holes in the wall ensure you are not drilling

where there could be any electric wires, water or gas pipes.

Wall mounting the TV

This television requires a VESA 400 x 200 wall mount, or equivalent.

1) Remove the four screws highlighted below.

2) The wall mount can now be easily attached to the mounting holes on the rear of the TV. These holes

are indicated in the picture below.

Detaching the stand and wall mounting

ﬁ g 1

ﬁ g 2

For optimum viewing, if wall mounting the TV

higher than eye level, the TV should be tilted

downwards so that the TV’s screen is ‘face on’.

See ﬁ g 1 and 2

Important – If wall mounting this TV, only

use the screws already provided in the wall

mounting holes. Using other screws which

are longer could cause irreparable damage to

internal parts.

Viewing angle

INCORRECT

CORRECT

User Guide - Technika - LCD 46-270.indd Sec1:10User Guide - Technika - LCD 46-270.indd Sec1:10 13-Dec-11 4:42:56 PM13-Dec-11 4:42:56 PM

1111

GETTING STARTED  INITIAL SET UP

Getting Started - Initial Set Up

1) Using the RF cable supplied, connect the TV

to the TV Aerial wall socket (Fig A)

2) Connect the power cable to the Electrical

outlet (Fig B)

5) You will now be welcomed with the initial set-up

screen.

Ecohome mode: Select this mode for the most

energy efﬁ cient TV set up*

If it does not appear, on the remote control, please

press [MENU] then 8-8-8-8 and the menu will appear.

Press OK on the remote control and tuning will start.

6) After tuning the following screen will

appear.

If you are missing channels, the reason for this is likely to be signal strength, you should

consider connecting signal booster and re-tuning the TV.

Fig A

Fig B

4) Insert the batteries supplied into the

Remote control and press the Standby

button to power on the TV

3) Switch on the television using the

power on/off switch.

Power on/off

As part of our ongoing development to reduce power consumption, we have added an extra function to this Television

called ‘Ecohome’ (you will see this during the ﬁ rst time installation set up). Power consumption using the Ecohome

function is approximately 15% lower than some other modes. The picture brightness is reduced using the Ecohome

function. If this function is not suitable for your viewing environment, you can select other modes as necessary. (Please

note, ‘Professional’ mode is for optimum default picture settings, however, power consumption is approximately 15%

higher than ‘Ecohome’ mode)

Please refer to the user guide section ‘Picture settings’ in order to change the mode to one that maybe more suitable for

your environment. There is also a shortcut button on the remote control called ‘P-Mode’ should you wish to change to

another mode.

User Guide - Technika - LCD 46-270.indd Sec1:11User Guide - Technika - LCD 46-270.indd Sec1:11 13-Dec-11 4:42:56 PM13-Dec-11 4:42:56 PM

TV BUTTONS & SOURCE MENU

Choosing Mode Input/Source

To switch between the different input/

connections.

A) Using the buttons on the remote control:

1) Press [SOURCE/ AV] - The source menu will

appear

2) Press [\/] or [/\] to select the input you

require.

3) Press [OK]

B) Using the buttons on the Television:

1) Press [SOURCE]

2) Scroll up / down using CH+/ CH- buttons to

the input/source you require

3) Press Vol+ to change input/source to the

one selected.

TV Buttons and Source Menu

Displays the input source menu

Displays Menu/OSD

Volume up and menu right

Volume down and menu left

Programme/Channel up and menu up

Programme/Channel down and menu down

Standby Power On/Off

User Guide - Technika - LCD 46-270.indd Sec1:12User Guide - Technika - LCD 46-270.indd Sec1:12 13-Dec-11 4:42:57 PM13-Dec-11 4:42:57 PM

1313

REMOTE CONTROL

Remote Control

STANDBY - Switch on TV when in standby or vice versa

MUTE - Mute the sound or vice versa

TV/RADIO - Switch to Freeview and switch between TV and

radio in Freeview mode

TV GUIDE - Opens the 7 Day TV Guide (Freeview mode)

ATV - Switch to analogue TV source

USB - Switch to USB Source

S.MODE - Scrolls through sound mode options

P.MODE - Scrolls through picture mode options

- To restart the current chapter

- To advance forward to the next chapter

- To stop the playback

- To play in fast rewind mode

- To play in fast forward mode

- To play/pause

SOURCE/AV - To display the input/source menu

INFO - Press once for now/next channel information

Press twice for programme information about current

programme

- Allows you to navigate the on-screen menus

and adjust the system settings to your preference

MENU - To display OSD menu

EXIT - To exit all menus

NUMBER BUTTONS - 0 – 9 to select a TV channel directly.

- To return to the previous channel viewed

FAV - To display favourites menu

VOL - To increase / decrease the sound level

SUBTITLE - To switch the dialogue at the bottom of the screen

(on/off)

ASPECT - To switch the screen between the different picture

formats

AUDIO - To change the audio language (if available)

SLEEP - Press repeatedly to cycle through the sleep options

CH To increase or decrease the channel being watched

TEXT - Teletext mode - To enter Teletext

INDEX - Teletext mode - To display the index page

REVEAL - Teletext mode - To reveal or hide the hidden words.

DISPLAY - To switch off the screen when listening to radio

SIZE - Teletext mode - To change the display size in Teletext

mode

HOLD - Teletext mode - Hold current page which is displayed

Only operate when a

USB key is inserted

User Guide - Technika - LCD 46-270.indd Sec1:13User Guide - Technika - LCD 46-270.indd Sec1:13 13-Dec-11 4:42:58 PM13-Dec-11 4:42:58 PM

USB USB port

HDMI 1 HDMI input

HDMI 2 HDMI input

HDMI 3 HDMI input

VGA(PC) VGA-PC input

VGA(PC) Audio In 3.5mm PC audio input

CI CARD IN Common Interface Card Input

SCART SCART input

COAX Audio Out Digital Coax output

COMPONENT (HD) Component input (YPbPr)

VIDEO Video input

R/L (AUDIO) Video / Component audio input

RF IN RF / TV Aerial Input

HEADPHONES 3.5mm Headphone output

Connecting a DVD Player/Recorder, Video Recorder or

Cable/Satellite Box

TVs Input/Source should be set to SCART

Connections

RF I N

SCART

TV Aerial

Wall Socket

SCART

OUT

DVD or VCR

User Guide - Technika - LCD 46-270.indd Sec1:14User Guide - Technika - LCD 46-270.indd Sec1:14 13-Dec-11 4:42:58 PM13-Dec-11 4:42:58 PM

1515

CONNECTIONS

Connecting a Camcorder, Camera or Games Console

Source should be set to Video

Connecting a High Deﬁ nition (HD) Device

Option 1 - via HDMI to HDMI cable

A HDMI cable can output both video and audio and enables you to enjoy digital-quality video and audio

with minimal loss of quality.

TVs Input/Source should be set to HDMI.

Option 2 - via Component cable

If you are supplied with a cable from the device which has RED, GREEN, BLUE, RED & WHITE connectors

you must connect via Component (for picture) and by phono cable (for sound).

TV Source should be set to Component.

Connections

Component (HD)

Component

Green

Blue

Red

A u di o L/ R

White

Red

Audio

In L/R

Ca mera or

Camcorder

Yellow

White

Red

Audio

In L/R

Video

HDMI OUT

HDMI

User Guide - Technika - LCD 46-270.indd Sec1:15User Guide - Technika - LCD 46-270.indd Sec1:15 13-Dec-11 4:42:58 PM13-Dec-11 4:42:58 PM

TV Menu Operation

CHANNEL MENU

Auto Tuning - Allows you to retune the television for all digital channels, digital radio stations and

analogue channels.

Freeview Manual Tuning- Allows you to manually tune your digital signal

Analogue Manual Tuning - Allows you to manually tune your analogue signal

Programme Edit - Allows you to delete, skip and add favourite channels.

To access this menu, press [MENU] button on the remote control. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons. To conﬁ rm

any settings press [OK] button.

To exit this menu at anytime, press [EXIT] button.

User Guide - Technika - LCD 46-270.indd Sec1:16User Guide - Technika - LCD 46-270.indd Sec1:16 13-Dec-11 4:42:58 PM13-Dec-11 4:42:58 PM

1717

TV Menu Operation

PICTURE MENU

To access this menu, press [MENU] button on the remote control. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons.

To conﬁ rm any settings press [OK] button.

To exit this menu at anytime, press [EXIT] button.

Picture Mode - Choose from the following presets

Standard Default settings

Dynamic Recommended settings for fast moving pictures

Mild Set to be lighter in colour and less bright

Personal Lets you manually alter all the settings

Ecohome 15% less power consumption

Contrast - Switch the balance between black and white

Brightness - Increase or decrease the brightness of the picture

Colour - Increases the colour from black and white

Tint - Lets you increase or decrease the level of tint within the picture

Sharpness - Increase or decrease the sharpness of the picture

Colour Temperature - Choose from the following presets

Normal Default settings

Warm Increases red within the picture

Cool Increases blue within the picture

Noise Reduction - Choose from the following presets

Off Turns noise reduction off

Low Minor system adjustment

Middle Medium system adjustments

High Maximum system adjustments

Default Default settings

Tip: If you do not press any buttons for 10 seconds, the menu will automatically exit. You can change the

length of time before the menu exits automatically - see ‘Menu Duration’ section.

User Guide - Technika - LCD 46-270.indd Sec1:17User Guide - Technika - LCD 46-270.indd Sec1:17 13-Dec-11 4:42:59 PM13-Dec-11 4:42:59 PM

TV Menu Operation

SOUND MENU

Treble - To adjust the amount of high frequency within the sound

Bass - To adjust the amount of low frequency within the sound

Balance - To switch the sound between the left and right speakers

Auto Volume Level (AVL) - When ‘on’ is selected, the volume will stay at a constant level regardless of

input/source

AD Volume - Increase or decrease the overall volume

Sound Mode - Choose from the following presets

Standard Default settings

Music Emphasises music over voices

Movie Provides live and full sound for movies

Personal Selects your personal sound settings

Sports Emphasises sound for sports

Digital Output - This is the digital COAX Audio output. Choose from the following options:

Off Off

Auto Selects the best settings automatically

PCM Select this option if you are connecting to a Stereo Hi-ﬁ via coax cable (Pulse-code

modulation (PCM) is a digital representation of an analogue signal)

To access this menu, press [MENU] button on the remote control. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons. To conﬁ rm

any settings press [OK] button.

To exit this menu at anytime, press [EXIT] button.

Tip: Treble and bass levels can only be adjusted when the sound mode ‘Personal’ is selected.

User Guide - Technika - LCD 46-270.indd Sec1:18User Guide - Technika - LCD 46-270.indd Sec1:18 13-Dec-11 4:42:59 PM13-Dec-11 4:42:59 PM

1919

TV Menu Operation

TIME MENU

To access this menu, press [MENU] button on the remote control. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons. To conﬁ rm

any settings press [OK] button.

To exit this menu at anytime, press [EXIT] button.

Clock - Shows the date and time

Off Time - Allows you to set a speciﬁ c time for your TV to turn off

On Time - Allows you to set a speciﬁ c time for your TV to turn on, the channel it will then display, the

source it will be on and also the volume. This function can then be toggled to repeat every day or a

certain day.

Time Zone - Change your current time zone

Sleep Timer - Lets you set the sleep timer so the television automatically switches off after a set amount of

time. Off -> 10min -> 20min -> 30min -> 60min -> 90min -> 120min -> 180min -> 240min

Auto standby - Toggle the Function on and off

User Guide - Technika - LCD 46-270.indd Sec1:19User Guide - Technika - LCD 46-270.indd Sec1:19 13-Dec-11 4:43:00 PM13-Dec-11 4:43:00 PM

TV Menu Operation

FEATURE MENU

Schedule List - Lists your programme reminders

CI Information - Pay per view services require a “smartcard” to be inserted into the TV.

If you subscribe to a pay per view service the provider will issue you with a ‘CAM’ and a “smartcard”. The

CAM can then be inserted into the COMMON INTERFACE PORT (CI Card In).

System Lock - Allows you to lock or unlock the menu. You will be asked to enter a 4 digit password use

the

button to quit the password input. Use the button to clear. Default password is 0000

To access this menu, press [MENU] button on the remote control. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll buttons. To conﬁ rm

any settings press [OK] button.

To exit this menu at anytime, press [EXIT] button.

User Guide - Technika - LCD 46-270.indd Sec1:20User Guide - Technika - LCD 46-270.indd Sec1:20 13-Dec-11 4:43:00 PM13-Dec-11 4:43:00 PM

2121

TV Menu Operation

SETUP MENU

To access this menu, press [MENU] button on the remote control. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons. To conﬁ rm

any settings press [OK] button.

To exit this menu at anytime, press [EXIT] button.

Blue Screen - Changes the background when there is no input between clear and a blue background (Only

available on some sources)

Menu Duration - Lets you adjust the amount of time the On Screen Menu stays on the screen before

disappearing

Reset to default

Reset Menu System - This resets the menus to factory settings.

Reset TV Channels - This clears all the TV channels from the television.

Software Update (USB) - From time to time we may release new ﬁ rmware to improve the operation of

the television (available to download). This menu lets you install the new software/ﬁ rmware onto the

television. Further details of how to do this will be issued with the ﬁ rmware. Contact the helpline or refer

to the ‘product support’ section of the website.

Menu language - Allows you to change the language of the menu

Auo

Automatically displays the best picture format. So the

picture is in the correct position. May have black lines

At the top/bottom and/or sides.

Zoom

Original

16:9

The picture

is the correct

proportion but

zoomed in to

ﬁ ll the screen

Will display the picture from the broadcaster

without any change

14:9

Aspect Ratio - Within the UK the picture format

varies depending on the channel/broadcast.

There are a number of different options to best

meet your needs

4:3

Displays the

14:9 picture

in the correct

proportion. As

a result side

bars are shown

on the screen

Displays the 4:3

picture in its

original size.

Side bars are

shown to ﬁ ll the

16:9 screen

Fills the screen

with a regular

16:9 signal.

User Guide - Technika - LCD 46-270.indd Sec1:21User Guide - Technika - LCD 46-270.indd Sec1:21 13-Dec-11 4:43:00 PM13-Dec-11 4:43:00 PM

PC Operation

USING THE TELEVISION AS A COMPUTER MONITOR

IMPORTANT – Before connecting the computer to the television you must ensure the computer settings

are correct for the television. You MUST do this using your old monitor.

How to set up for Windows XP & Windows Vista (connecting via VGA cable to the TV)

1) Switch on your computer

2) When ﬁ nished booting up right click your

mouse anywhere on the screen

4) Left click your mouse on Setting/Display Settings.

Ensure the screen resolution is set to what is shown

in the technical speciﬁ cations section toward the

rear of this user guide. To correct the resolution to

that of the television move the slider.

6) Left click on the drop down for Screen refresh rate and select 60 Hertz, if you experience picture noise

or ‘ﬂ ickering’, select 50 hertz or 70 hertz.

7) Click on Apply, then click Yes and the settings will be saved.

8) Now switch off your computer and connect the

television (as shown)

9) Switch on the TV, select the input/source to

VGA/PC and re-start your PC.

Connecting a Laptop

In addition to the above if you are connecting a laptop to the television you will also need to activate the

VGA connection on the laptop. This can vary based on the brand of laptop you have, on many brands/

models, it is as per below.

1) Connect the laptop to the television

2) On the Laptop push buttons

The screen will now switch to the television.

3) Left click your mouse on Properties/Personalise

5) Left click your mouse on Advance/Advanced

Settings and left click on Monitor

User Guide - Technika - LCD 46-270.indd Sec1:22User Guide - Technika - LCD 46-270.indd Sec1:22 13-Dec-11 4:43:02 PM13-Dec-11 4:43:02 PM

2323

PC SETTINGS

To access this menu, press [MENU] button on the remote control. To enter a menu press [OK]

If you wish to make changes to any of the default settings, use the scroll

buttons. To conﬁ rm

any settings press [OK] button.

To exit this menu at anytime, press [EXIT] button.

Auto Adjust - Lets you automatically conﬁ gure the television to be used as a computer monitor

H Offset - Changes the horizontal position of the picture

V Offset - Changes the vertical position of the picture

Size - increase picture size

Phase - To adjust delay time of phase in order to reduce the noise of picture

Position Reset - Changes back to the original settings

Tip: If the computer is left in-active for a period of time, the television will switch into a ‘sleep’ state

(the screen will power off to save power). To switch back on press the standby button.

PC Operation

User Guide - Technika - LCD 46-270.indd Sec1:23User Guide - Technika - LCD 46-270.indd Sec1:23 13-Dec-11 4:43:02 PM13-Dec-11 4:43:02 PM

Page is loading ...

Technika LCD 40-270, LCD 40 - 270, LCD 46 - 259, LCD 46 - 270 User manual

Related papers

Other documents