ADJ Trance Wheel 250 User manual

Brand: ADJ

Model: Trance Wheel 250

Category: DJ controllers

Type: User manual

User Instructions

©American DJ® - www.americandj.com - Trance Wheel 250™ Instruction Manual Page 2

Unpacking: Thank you for purchasing the Trance Wheel 250™ by

American DJ®. Every Trance Wheel 250™ has been thoroughly tested

and has been shipped in perfect operating condition. Carefully check

the shipping carton for damage that may have occurred during ship-

ping. If the carton appears to be damaged, carefully inspect your unit

for any damage and be sure all equipment necessary to operate the

system has arrived intact. In the event damage has been found or parts

are missing, please contact our toll free customer support number for

further instructions. Please do not return the unit to your dealer without

rst contacting customer support.

Introduction: Thank you for purchasing the American DJ® Trance

Wheel 250.

™

The Trance Wheel 250™ has an internal oil wheel that

projects a multi-colored psychedelic patterns on a wall or any surface.

The unit uses a rotating oil wheel projected through a beveled piece of

glass to create a truly unique effect. The unit has 3-way mode switch

that allows the unit to be operated in three different modes (see page 7

for operating modes). To optimize beam intensity use this xture with a

fog machine or other type of special effect smoke.

Customer Support: American DJ® provides a toll free customer sup-

port line, to provide set up help and to answer any question should

you encounter problems during your set up or initial operation. You

may also visit us on the web at www.americandj.com for any com-

ments or suggestions. For service related issue please contact Ameri-

can DJ®. Service Hours are Monday through Friday 9:00 a.m. to 5:00

p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ.

PLEASE recycle the shipping carton whenever possible.

Trance Wheel 250™ General Introduction

American DJ®

4295 Charter Street

Los Angeles, CA. 90058

www.americandj.com

.12/03

©American DJ® - www.americandj.com - Trance Wheel 250™ Instruction Manual Page 4©American DJ® - www.americandj.com - Trance Wheel 250™ Instruction Manual Page 3

Please carefully read and understand the instructions in this manual

thoroughly before attempting to operate this unit. These instructions

contain important safety information regarding the use and mainte-

nance of this unit. Please keep this manual with the unit, for future ref-

erence.

Trance Wheel 250™ General Instructions Trance Wheel 250™ Precautions

Safety Issues: This unit may blow the breaker if the maximum allot-

ted load of 5 amps is reached. If the breaker needs replacement, always

replace the breaker with same exact type that was remove, unless oth-

erwise instructed by an authorized American DJ® service technician.

Use of a different type breaker from that which is recommended may

cause fire or electric shock and will void the manufactures warranty.

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit

• Do not attempt to operate this unit if the power cord has been frayed

or broken

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short

• Disconnect from main power before making any type of connection

• Do not remove the cover under any conditions. There are no user

serviceable parts inside

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall

• Do not attempt to operate this unit, if it becomes damaged

• This unit is intended for indoor use only, use of this product outdoors

voids all warranties

• During long periods of non-use, disconnect the unitʼs main power

• Always mount this unit in safe and stable matter

• Power cords should be routed so they are not likely to be walked on,

pinched by items placed upon or against them.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 9 for cleaning details

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances

(including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the unit.

C. The unit has been exposed to rain or water.

D. The unit does not appear to operate normally or exhibits a

marked change in performance.

• Beveled glass lter may be removed for an oil wheel only effect

• Easy Lamp Replacement

• ZB-ELC 24V/250W

• Compact High-Tech Case Design

• Built-In Hanging Yoke

• Internal Microphone

• Fan Cooled

• Unique internal colored oil wheel

• 3-Way Effects Switch - 3 Operating Modes

• Sound Active

Trance Wheel 250™ Features

Trance Wheel 250™ Warranty Registration

The Trance Wheel 250™ carries a one year (365 days) limited war-

ranty. Please fill out the enclosed warranty card to validate your pur-

chase. All returned service items whether under warranty or not, must

be freight pre-paid and accompany a return authorization (R.A.) num-

ber. If the unit is under warranty you must provide a copy of your proof

of purchase invoice. Please contact American DJ® customer support

for a R.A. number.

Halogen Lamp Warning! This fixture is fitted with

halogen lamps which are highly susceptible to

damage if improperly handled. Never touch the

lamps with your bare fingers as the oil from your

hands will shorten lamp life. Also, never move the

fixture until the lamps have had ample time to cool.

Remember, lamps are not covered under warranty

conditions.

Trance Wheel 250™ Halogen Lamp Warning

©American DJ® - www.americandj.com - Trance Wheel 250™ Instruction Manual Page 5 ©American DJ® - www.americandj.com - Trance Wheel 250™ Instruction Manual Page 6

Trance Wheel 250™ Control & Functions Trance Wheel 250™ Control & Functions

1. Mirror - This is a highly reective surface mirror specically

designed to optimize and enhance beam output. Never use glass

cleaner that contains ammonia to clean the surface of the mirror (such

as Windex).

2. Lens - This is a fully focusing high quality lens. Focus the lens by

manually turning the lens in a clockwise or counter-clockwise direc-

tion.

3. Glass Filter - This unit comes with a built-in glass lter. This lter

may be removed at any time for a completely different effect. To remove

the lter unscrew the retaining thumb screw and gently pull the lter

out.

4. Fan - Cooling fan. For optimal performance keep this fan grill clean

at all times.

5. Lamp Assembly Retaining Screws - These two screw hold the

lamp assembly in place.

6. Lamp Assembly Cover - This plate accesses the lamp socket

assembly. This cover is held securely in place by a single thumb screw.

The fan is also attached to this cover.

7. Lamp Cover Retaining Screw - This thumb screw holds the lamp

socket assembly cover into place

8. Function Switch - This is a 3-way function switch. This unit can

be operated in three different mode all of which are controlled by this

switch.

9. Microphone - This microphone receives external low frequencies

to trigger the unit.

10. Breaker - A 5A built-in safety breaker to reduce the risk of electrical

shock or re and protect the circuitry. In the case of a internal short or

power surge.

11. Power Cord - Connect only to a matching power outlet. Never

use this xture is the ground prong has been removed or broken off.









Trance Wheel 250™ Breaker & Lamp Replacement

©American DJ® - www.americandj.com - Trance Wheel 250™ Instruction Manual Page 8

Trance Wheel 250™ Operation

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

Trance Wheel 250™ before attempting operation.

General Operation: Just plug this light in, and watch it go. This fix-

ture is designed to operate as a stand alone unit. It has been tested

and the lamp has been installed at the factory there is no assembly

necessary. The Trance Wheel 250™ is ready to be plugged in, out of

the box. There is no power switch, after plugging the unit the unitʼs

internal beveled glass wheel will rotate continuously in a single direc-

tion, while the outside color dish will rotate back and forth to the beat

of music. The unit will create multi-colored patterns that will simulate

the rippling effect of water. If there is no lamp output check the break-

er and bulb. If the breaker and bulb are good, please return the unit

for servicing.

Operating Modes:

This unit comes with a 3-way multi-operating switch located on the

rear of the unit. The switch controls three (3) different operating

modes; Static, Sound Active, and Continuous Rotation.

Switch in the "I" position: Mode 1 - In this mode the internal oil wheel

and the external multi-mirror dish will spin continuously in clockwise

direction, regardless of the presence of sound.

Switch in the “0” position: Mode 2 - In this mode the internal oil wheel

will continuously rotate while the external multi-mirror dish will remain

static. In this mode the unit may be used as a projector.

Switch in the “II” position: Mode 3 - In the this mode the internal oil

wheel will continuously rotate in one direction while the outer multi-

mirror dish will react to sound. Please note that tapping on the unit, or

high pitched sounds may not trigger the unit, the unit is designed to

react to low frequencies (bass). Also note that the music sensitivity is

preset at the factory and may not be changed or adjusted.

Focusing:

The unit has a fully focusing lens. The lens is focused by manually

turning the lens in either a clockwise or counter-clockwise direction.

©American DJ® - www.americandj.com - Trance Wheel 250™ Instruction Manual Page 7

Caution: Always replace with the exact same type lamp, unless oth-

erwise specified by an authorized American DJ® technician. Replace

with anything other than the specified part can damage your unit and

will void your manufactures warranty.

Warning: If after you have replaced the lamp or reset the breaker

and you continue to blow either one, STOP using the unit. Contact

customer support for further instructions, you may have to return the

unit for servicing. Continuing to use the unit may cause serious dam-

age.

Breaker Reset: This unit is equipped with a built-in safety breaker.

This breaker is designed to close the power circuit in the event of an

internal short or power surge. This will reduce the risk of electrical

shock or re and protect the circuitry. To reset the breaker, push the

breaker button in until you hear it “pop” back in to place. If the break-

er continues to pop, stop using the unit and contact our customer

support team, the unit may need to be returned for service.

Lamp Replacement: Caution! Never open the unit when in use.

Always disconnect the main power and allow the fixture ample time

to cool before attempting to replace the lamp. Lamp replacement has

been made simple by incorporating a split dome that is retained by

thumb screws. Again, please remember to always replace with the

exact same type lamp.

1. Be sure to follow the proper procedures when handling halogen

lamps. Never touch the new lamp with your bare fingers.

2. Unscrew the single thumb screw located on the bottom of the

unit. You do not have to remove the four phillips screws, they

secure the fan in place.

3. Once the thumb screw has been removed, pull the lamp assembly

cover plate up to expose the lamp. The fan is attached to the

cover plate.

4. Remove and replace the lamp with an exact match.

5. Reassemble in reverse order.

©American DJ® - www.americandj.com - Trance Wheel 250™ Instruction Manual Page 10

1 YEAR LIMITED WARRANTY

A. American DJ® hereby warrants, to the original purchaser, American DJ® products to be

free of manufacturing defects in material and workmanship for a period of one year (365

days) from the date of purchase. This warranty shall be valid only if the product is purchased

within the United States of America, including possessions and territories. It is the ownerʼs

responsibility to establish the date and place of purchase by acceptable evidence, at the

time service is sought.

B. For warranty service, send the product only to the American DJ® factory. All shipping

charges must be pre-paid. If the requested repairs or service (including parts replacement)

are within the terms of this warranty, American DJ® will pay return shipping charges only

to a designated point within the United States. If the entire instrument is sent, it must be

shipped in its original package. No accessories should be shipped with the product. If any

accessories are shipped with the product, American DJ® shall have no liability whatsoever

for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product

is modied in any manner which American DJ® concludes, after inspection, affects the reli-

ability of the product; if the product has been repaired or serviced by anyone other than the

American DJ® factory unless prior written authorization was issued to purchaser by Ameri-

can DJ®; if the product is damaged because not properly maintained as set forth in the

instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period specied above, American DJ® will replace defec-

tive parts at its expense, and will absorb all expenses for warranty service and repair labor

by reason of defects in material or workmanship. The sole responsibility of American DJ®

under this warranty shall be limited to the repair of the product, or replacement thereof,

including parts, at the sole discretion of American DJ®. All products covered by this warranty

were manufactured after January 1, 1990, and bear identifying marks to that effect.

E. American DJ® reserves the right to make changes in design and/or improvements upon

its products without any obligation to include these changes in any products theretofore

manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any acces-

sory supplied with products described above. Except to the extent prohibited by applicable

law, all implied warranties made by American DJ® in connection with this product, including

warranties of merchantability or tness, are limited in duration to the warranty period set

forth above. And no warranties, whether expressed or implied, including warranties of mer-

chantability or tness, shall apply to this product after said period has expired. The con-

sumerʼs and or Dealerʼs sole remedy shall be such repair or replacement as is expressly

provided above; and under no circumstances shall American DJ® be liable for any loss or

damage, direct or consequential, arising out of the use of, or inability to use, this product.

G. This warranty is the only written warranty applicable to American DJ® Products and

supersedes all prior warranties and written descriptions of warranty terms and conditions

heretofore published.

H. Lamps are not covered under this or any other warranty either written or implied.

Trance Wheel 250™ Warranty

Fixture Cleaning:

Due to fog residue, smoke, and dust cleaning the internal and external

lenses should be carried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the

outside casing.

2. Clean the external optics with glass cleaner and a soft

cloth every 20 days.

4. Clean the internal optics with glass cleaner and a soft cloth

every 30-60 days.

5. Always be sure to dry all parts completely before plugging

the unit back in.

Cleaning frequency depends on the environment in which the fixture

operates (I.e. smoke, fog residue, dust, dew). In heavy use we recom-

mend cleaning on a monthly basis. Periodic cleaning will ensure

longevity, and crisp beam output.

Trance Wheel 250™ Cleaning

Trouble Shooting:

Listed below are a few common problems and solutions you should try

before contacting customer support.

Unit rotates but has no light output from the unit;

1. Be sure you have connected your unit into a matching wall outlet.

2. Remove the lamp cover and be sure the lamp is seated in its

socket properly. Occasionally lamps become loose during shipping

be sure the lamp is push in to its socket all the way.

3. Be sure the lamp is good.

Unit does not rotate and lamp does not turn on;

1. Be sure you have connected your unit into a matching wall outlet.

2. Be sure the external breaker has not blown. The breaker is located

on the rear panel of the unit.

3. Be sure the unit power cord is properly seated in the power outlet

and the outlet has power.

4. Be sure the breaker holder is securely seated in the breaker hold-

er housing.

Trance Wheel 250™ Trouble Shooting

©American DJ®

American DJ World Headquarters:

4295 Charter Street Los Angeles, CA 90058 USA

Tel: 323-582-2650 / Fax: 323-582-2610

Web: www.americandj.com / E-mail: [email protected]

Technical Specifications:

Model: Trance Wheel 250™

Voltage

: 120v~60Hz

Lamp: ZB-ELC 24v/250w

Breaker: 5 Amp

Dimensions: 14.75” H x 5.5” W x 7.25” D

Colors: Multi-Colored Oil Wheel

Lens: Removable Glass Filter

Weight: 6 Lbs.

Duty Cycle: None

Ventilation: Fan Cooled

Warranty: 1 Year (365 Days)

Please Note: Specications and improvements in the design

of this unit and this manual are subject to change without any

prior written notice.

Trance Wheel 250™ Specifications

ADJ Trance Wheel 250 User manual

Brand: ADJ

Model: Trance Wheel 250

Category: DJ controllers

Type: User manual

Download PDF

report

ADJ Trance Wheel 250 User manual

ADJ Trance Wheel 250 User manual

Related papers

Other documents