LG PQRCUDS0.ENCXLEU User manual

Type
User manual
ENGLISH
LG
Deluxe Wired Remote Controller
LG
IMPORTANT
• Please read this installation manual completely
before installing the product.
• Installation work must be performed in
accordance with the national wiring standards
by authorized personnel only.
• Please retain this installation manual for future
reference after reading it thoroughly.
Owner's & Installation Manual
Visit us at : http://www.lgservice.com
Models: PQRCUDS0
PQRCUDS0B
PQRCUDS0S
ITALIANO ESPAÑOL FRANÇAIS DEUTSCH
êìëëäàâ
2 Deluxe Wired Remote Controller
Deluxe Wired Remote Controller Owner’s & Installation Manual
TABLE OF CONTENTS
Safety Precautions............................................................3~4
Part Description.................................................................5~6
Wired remote controller switch information .......................7
Installation Method................................................................8
Necessary functions before using ................................9~11
• Trial Operation........................................................................................9
• Setting the Central Control Address ..................................................10
• ESP Function........................................................................................11
How to use the Mode Selection Button.......................12~16
• Cooling Operation................................................................................12
• Heating Operation ................................................................................13
• Auto-Operation.....................................................................................14
• Dry(Dehumidification) Operation........................................................15
• Fan Operation.......................................................................................15
• Fan Speed Selection ............................................................................16
Sub Function .......................................................................17
• Auto Swing............................................................................................17
• Plasma...................................................................................................18
• Ventilation.............................................................................................19
• Heater ....................................................................................................19
Special Function..................................................................20
• Child Lock.............................................................................................20
• Vane control..........................................................................................21
• Swirl Swing ...........................................................................................22
• Room Temperature Display.................................................................23
• Easy reservation...................................................................................23
• Setting the current time.......................................................................24
• Weekday reservation ...........................................................................25
• Different Mode Operation ....................................................................26
Note) Please, refer to indoor's manual for product's detail information of subfunction
Safety Precautions
Owner’s & Installation Manual 3
ENGLISH
Installation
Service Center
Original Parts
Safety Precautions
• The installation requires expert skills, and it should be installed by the service center or other shops specialized
in the installation and recognized by our company.
• For all the problems arising after installation by someone who has no relevant qualifications, LG will not provide
free service.
• The following safety cautions are provided to prevent unexpected dangers or losses.
: If the user does not follow the mandatory items, it may result in serious injury or death.
: If the user does not follow the mandatory items, it may cause personal injury or property
damage.
: Warning and Caution are to call the user’s attention to the possible danger. Read and follow
them carefully in order to prevent a safety accident.
: Warning and Caution are indicated in this guide and the product itself to help protect the users
from danger.
WARNING
CAUTION
WARNING
Entrust installation of the
product to the service center
because improper installation
may cause fire, an electric
shock, explosion, and physical
injury.
Use the original parts in
order to prevent fire, an
electric shock, explosion,
and product breakdown.
Keep combustible and/or
inflammable materials away
from the product in order to
prevent fire or product
breakdown.
Do not disassemble, repair, or
modify the product at your
discretion in order to prevent fire
or an electric shock.
Do not install the product in wet
and humid areas in order to
prevent product breakdown.
Do not expose the product to the
sun in order to prevent product
breakdown.
Safety Precautions
4 Deluxe Wired Remote Controller
Do not modify or lengthen the
power cable at your discretion.
It may cause fire or an electric
shock.
Do not place a heating device
near the product. It may cause
fire.
Do not drop water on to the
product. It may cause an electric
shock or product breakdown.
Do not place something heavy on
the power cable. It may cause fire
or an electric shock.
Do not place a heavy thing on the
product. It may cause product
breakdown.
If the product was submerged
under water, ask the service
center for instruction. It may
cause fire or an electric shock
unless you do that.
In-use
In-use
Service Center
Make sure children or senor
citizens use the product under
proper observation in order to
prevent safety accident.
Do not subject the product to
shock. It will cause product
breakdown.
Do not pick the product with a
sharp tool. It may cause
product breakdown with the
damage to its parts.
Do not clean the product with strong cleanser such
as solvent. Use soft clothes in order to prevent fire
or product deformation.
Do not touch the product with a wet hand. Do not
pull the lead cable. It may cause product breakdown
or an electric shock.
CAUTION
Part Description
Owner’s & Installation Manual 5
ENGLISH
1. Wired Remote Controller
2. LCD Screen
3. Connecting Cable and Connector
Part Description
Accessory
Connecting Cable
(1EA)
Fixing Screw (2EA) User / Installation
Manual
Installation Paper
Part Description
6 Deluxe Wired Remote Controller
Deluxe Wired Remote Controller
1
2
3
4
6
5
7
8
9
10
15
14
12
20
11
19
16
17
18
13
Each function will be shown on the display panel for three second or so when the initial power is on.
The analog panel enables you to use the remote controller with a touch of your own finger without pressing any
extra button.
However, if you press more than one button at the same time, it may cause malfunction.
1. Operation Display Panel
2. Room Temperature Button
3. Fan Speed Button
4. Fan / Plasma / Swirl Swing Button
5. Automatic / Vane Control Button
6. Timer Mode Button
7. Date Selection Button
8. Hour / Minute Button
9. Mode Selection Button
10. On / Off Button for reservation
11. Temperature Control Button
12. On / Off Button
13. Special Function Button
14. Dehumidification / Heater Button
15. Sub Function Button
16. Easy Reservation Button
17. Cancel Button
18. Heating / Ventilation Button
19. Setting Button
20. Cooling / Auto Swing / Child
Lock Button
Wired remote controller switch information
Owner’s & Installation Manual 7
ENGLISH
Group control
S/W 2
S/W GR
S/W 1
S/W
Ceiling height selection
Indoor temperature sensor selection
Product selection
1
2
1 2
1
2
3
123
Product selection switch
1. Cooling ONLY product
2. HEAT PUMP product
Indoor temperature sensor
selection switch
1. Use the temperature sensor on the
remote controller
2. Use the temperature sensor on the
product.
3. Use the sensor with the lower
temperature between the remote
controller and the product
Ceiling height selection
switch
1. Low ceiling
2. Standard ceiling
3. High ceiling
Group control switch
1. For individual control use
2. For group control use
Wired remote controller switch information
* When changing the product selection switch and group control switch, the power must be reconnected to reflect
the changes.
8 Deluxe Wired Remote Controller
Installation Method
The position of the fixing screws
Side of
remote Controller
Side of
Indoor Unit
Fixing the
remote controller
Fixing the
connecting cable
Main frame
CN-REMO
LO2K
J15
LO1K
LO1D
C07D
C01K
J14
CN-DISP
CN-M CN-ZONEC
IC01A
Be careful not to alter the colors
of the remote controller
connection cables.
Brown
Red Yellow
Yellow
Yellow
1
Put the installation paper on the place and determine the
position and height of the fixing screws of the wired remote
controller.
Refer to the printed side of the installation paper.
2
Plug the connecting cable into
the indoor unit.
The product is being shipped
with the cable connected only
to the remote controller. Put
each cable to the remote
controller according to the
color match
3
Remove the installation paper before installing
the remote controller so that it can fit into the
right place.
* When installing the wired remote controller, do not install it so that it is buried to the wall. (This can
cause error in the temperature sensor)
* When installing multiple wired remote controllers horizontally in one location, leave a minimum distance
apart (2cm). (This can cause error in the temperature sensor)
* Do not install the cable with a distance of 50 m or longer. (This can cause communication error.)
* When installing the cable, check whether the connector between the remote controller and the product is
installed properly. The connector will not be connected when installed in opposite sides.
Supply the power after connecting wired remote controller.
When you need to change wired remote controller, switch off the main power and change it Before switch off
the main power if changed the wired remote controller , you can't use the option function of the indoor unit.
Installation Method
Owner’s & Installation Manual 9
ENGLISH
Necessary function before using
Necessary functions before using
The trial operation is to check the installation status of the product. The temperature will not be controlled during
trial operation. Instead the product will operate in several modes such as cooling, strong wind, comp-on.
* This function might not be available for Multi Product like Multi V system.
1
The trial operation is to check the installation status of
the product. The temperature will not be controlled.
Instead the product will operate in several modes such
as cooling, strong wind, comp-on.
2
If you wan to do the trial operation, press the Special
Function button and then select the trial operation
mode.
3
Then the product will begin the trial operation and the
display will be like the following picture.
4
The trial operation will continue for 18 minute or so
and the product will go into standby mode.
4
If you wan to cancel the trial operation during the
process, press the On/Off button.
Trial Operation
10 Deluxe Wired Remote Controller
Note : The remote controller displays 'HL' if central controller has locked the remote controller .
Necessary function before using
1
Press the Special Function button.
2
Press the address setting button. Press the
temperature-increasing button to change the group
number. Press the temperature-decreasing button to
change the indoor unit number. The number of the
central control address group is "2." And the number of
the indoor unit is "5."
3
If you press the address setting button, the addressing
setting mode will be unset.
* If you connect the indoor unit to the central controller,
you should set the network address of the indoor unit
so that the central controller could recognize it.
* The central control address is composed of the group
number and the indoor-unit number.
Setting the Central-Control Address
Owner’s & Installation Manual 11
ENGLISH
Necessary function before using
100 unit 10 unit
1
Press the Special Function button.
2
Press the E.S.P button.
3
Set the volume of each air flow (Low, Medium, Hi) by
using the temperature control button. Press the air flow
button to select the air flow.
(The value of E.S.P could be adjusted from 1 to 225.)
(The figure on the left shows when the strong winds
ESP value has been set to 212.)
4
If you press the E.S.P button one more time, the E.S.P
value will be set and the setting mode will be unset.
E.S.P function is setting the volume of each air flow. It is for the convenience of installation. It is recommended
that you should not use this function whild using the remote controller.
* The E.S.P value is set at the proper value at the factory. So it is highly recommended that you should do not
change the E.S.P value at your discretion.
ESP Function
12 Deluxe Wired Remote Controller
What is the three-minute delay function?
The function to protect the compressor delays the output of cool air when operating instantly after
interrupting the cooling operation.
Cooling operation restarts after 3 minutes when the compressor starts to operate.
How to use the Mode Selection Button
A click of the button will increase the expected temperature by 1°C
A click of the button will decrease the expected temperature by 1°C.
1
Cooling operation will begin if you press the On/Off
button.
3
Press the operation selection button and choose one of
the functions among blowing, automation, heating, and
dehumidification if you want another operation mode
during the operation.
4
If you press the On/Off button, the cooling operation
will stop.
2
Press the temperature button and set the expected
temperature lower than the current room temperature.
(18~30°C)
If the expected temperature is set higher than the current
room temperature, the cooling function will not begin and
just the blowing operation will continue.
Cooling Operation
How to use the Mode Selection Button
You can choose the expected temperature from 18(C to 30(C.
It is recommended that the ideal difference of the temperature between indoors and outdoors should be
less than 5°C.
Owner’s & Installation Manual 13
ENGLISH
How to use the Mode Selection Button
A click of the button will increase the desired temperature by 1°C.
A click of the button will decrease the desired temperature by 1°C.
What is the three-minute delay function?
It will take a time for the product to blow warm air. The delay is just to protect the compressor.
The room will be heated with warm air after three minutes when the compressor begins operation.
The cooling-only model will not do heating function.
Heating Operation
1
Press the heating button after pressing the On/Off
button of the remote controller.
2
Set the expected room temperature higher than the
current room temperature. (16~30°C)
3
Press the operation selection button and choose one of
the functions among blowing, automation, heating, and
dehumidification if you want another operation mode
during the operation.
4
If you press the On/Off button, the heating operation
will stop.
* If the expected temperature is set lower than the current
room temperature, the heating operation will not begin
and just the blowing operation will continue.
14 Deluxe Wired Remote Controller
How to use the Mode Selection Button
1
Press the On/Off button and then press the Automatic
Operation button.
2
When the room temperature is lower than the
expected temperature: Heating Operation.
When the room temperature is higher than the
expected temperature: Cooling temperature.
3
Press the operation selection button and choose one
of the functions among blowing, automation, heating,
and dehumidification if you want another operation
mode during the operation.
4
If you press the On/Off button, the cooling operation
will stop.
Auto-Operation
The cooling-only model will show AI on the temperature display.
AI could be adjusted by five levels (-2, -1, 0, +1, +2).
This auto-operation is not related to "Auto Change Over" function.
Owner’s & Installation Manual 15
ENGLISH
How to use the Mode Selection Button
1
Press the On/Off button on the remote controller.
2
Select the dehumidification function by pressing the
Mode selection button.
3
When the dehumidification is being done, dh will be
shown on the display panel
4
Press the operation selection button and choose one
of the functions among blowing, automation, heating,
and dehumidification if you want another operation
mode during the operation.
1
Press the On/Off button on the remote controller.
2
Select the Fan function by pressing the Mode selection
button.
3
When the Fan is being done, "fn" will be displayed on
the display panel.
4
Press the operation selection button and choose one
of the functions among heating, automation, cooling
and dehumidification if you want another operation
mode during the operation.
Dehumidification Operation: Dehumidification by lowering temperature slightly
If used during the rainy season or high humidity, you can have both of effective dehumidifying
and air conditioning effect.
Temperature control is not available in the Dehumidification Operation.
Temperature control is not available in the air fan operation.
Fan operation does not output cool air, but just the fan air.
By giving out air that has no difference of temperature with the indoors, it allows ventilation of
the room.
Dehumidification Operation
Fan Operation
16 Deluxe Wired Remote Controller
How to use the Mode Selection Button
Po
Hi
Med
Fan Speed Selection in Cooling Operation
Lo
Fan Speed Selection in Heating, Dry, Fan,
Auto-Operation
Hi
Med
Lo
1
Select the proper fan speed which you want by
pressing the fan speed button on the remote controller.
If you press the fan speed button, the strength of the
fan speed will change in the order of Low Medium
Hi Power.
If the product is not compatible with the fan speed
control, it will not function as your selection.
If the indoor unit is compatible with the slo fan speed, you
can adjust the air flow slow level.
You can easily control the fan speed.
Fan Speed Selection
Owner’s & Installation Manual 17
ENGLISH
Sub Function
Sub Function
Auto Swing
You can control the wind direction easily.
1
Press the Sub function button on the remote controller.
2
Press the automatic Auto Swing button.
3
A click of Auto Swing button will turn on/off the
indicator.
* If the product is not compatible with the automatic wind direction mode, it will not operate
automatically.
18 Deluxe Wired Remote Controller
Ventilation
You can use the ventilation function.
1
Press the Sub function button of the remote controller.
2
Press the ventilation button.
A click of the ventilation button will turn on/off the
indicator.
However, even when the remote controller that does not
have the ventilation function displays ventilation, the
actual product does not operate for ventilation.
Sub Function
Plasma
You can use the plasma function.
1
Press the Sub function button.
2
Press the Plasma button.
A click of the Plasma button will turn on/off the indicator.
If the product is not compatible with the Plasma function,
it will not do the Plasma function even though the
indicator is turned on.
Plasma Function is possible when only product is
operating.
Please press the Plasma button in Fan Mode, If you want
to operate only plasma function.
Owner’s & Installation Manual 19
ENGLISH
Sub Function
Heater
You can use the heater function.
1
Press the Sub function button.
2
Press the heater button.
A click of the heater button will turn on/off the indicator.
If the product is not compatible with the heating function,
it will not do the heating function.
Special Function
20 Deluxe Wired Remote Controller
Special Function
This is a function to prevent tampering of settings by children or others.
You can use the child lock function.
Child Lock
1
Press the Special Function button of the remote
controller.
2
Press the child lock button.
A click of the child lock button will turn on/off the indicator.
If you press another button while adjusting child lock
function, the temperature display will show CL for three
seconds and then the operation will come back to the
original mode.
If you want use the child lock function in standby mode,
select child lock and press the On/Off button within three
seconds. Then the standby mode will change into the
child lock mode.
If you want to cancel the child lock function in the standby
mode, just press the child lock button.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27

LG PQRCUDS0.ENCXLEU User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI