AEG Electrolux esa185bgmb-i User manual

Brand: AEG Electrolux

Model: esa185bgmb-i

Type: User manual

This manual is also suitable for

ESA185BGMB/E

AEG Electrolux esa185bgmb-i is a powerful air conditioning unit with a variety of features to keep you comfortable all year round. It has a cooling capacity of 18000 BTU/h and a heating capacity of 15000 BTU/h, making it ideal for medium to large rooms. The unit also features an energy-saving mode, a sleep mode, and a turbo mode for quick cooling or heating.

The AEG Electrolux esa185bgmb-i is easy to use, with a remote control and a clear LED display. It also has a built-in timer, so you can set it to turn on or off automatically. The unit is also relatively quiet, with a noise level of only 48 dB(A) in cooling mode and 50 dB(A) in heating mode.

AIR CONDITIONER

(SPLIT TYPE)

Thank you very much for choosing our product.

Please read this owner's manual carefully before using your air conditioner.

OWNER'S MANUAL'

MAINTENANCE

ER S

ALE

SERVI

NOT

ICE

LOC

ATIO

tio

Periodically check the air inlet and outlet on both the indoor and outdoor unit for blockages.

If they are blocked, clear them.

If you plan to idle the unit for a long time.

1. Operate the fan for about half a day to dry the inside of the unit.

2. Stop the air conditioner and disconnect the power source. Remove the batteries from

the remote controller.

3. The outdoor unit requires periodic maintenance and cleanin

g. Do not attempt to do this

yourself. Please contact your dealer or servicer.

5. Install the air freshening filter back into position.

6. Insert the upper portion of air filter back into the unit taking care that the left and right edges

line up correctly and place filter into position.

Be sure your power supply meets the specifications on the nameplate.

An earth leakage circuit breaker or air-breaker shoul

d be installed in the power wiring system.

The capacity of the breaker should be 1.5 times of the maximum ampere rating of the unit.

To avoid electric shock, please ground the unit.

The air conditioner MUST be used on dedicated circuit.

If need be, use the power fuse or the circuit breaker specified in INSTALLA

TION MANUAL.

Never pull on any of the wiring . T

o change the wiring ,please call a professional electrician or

servicer.

If the supply cord is damaged, please call a professional electricia

n or servicer for repairs.

Please mount the unit in a stable location to avoid the noise or vibration.

Find a location for the outdoor unit where noise and hot air emitted by the unit will be of the

least inconvenience to your neighbour

If the air conditioner sounds abnormal during oper

ation, contact the dealer where you

purchased the air conditioner.

If you move out or if it is desired to relocate the air conditioner, consult your dealer.

See

INSTALLATION MANUAL.

Should you need servicing on your air conditioner, please shut the unit off and contact your

dealer or servicer.

INSTALLATION

CONTENTS

PARTS NAMES AND THEIR FUNCTIONS.................................................................

AIR CONDITIONER OPERATION AND PERFORMANCE.........................................

AIR CONDITIONER OPERATING CONDITIONS

REMOTE CONTROLLER

TEMPORARY OPERATION

ADJUSTING AIR FLOW DIRECTION

PRECAUTION.............................................................................................................

CHECKS BEFORE OPERATION

HINTS FOR ECONOMICAL OPERATION

SAFETY INFORMATION

CARE AND MAINTENANCE......................................................................................

TROUBLESHOOTING THE AIR CONDITIONER

NONPROBLEMATIC OPERATIONS

CLEANING

MAINTENANCE

AFTER SALES SERVICE

INSTALLATION...........................................................................................................

NOTICE

LOCATION

CAUTION

10. Heating operation

During the HEATING operation, the air

conditioner absorbs the heat outside the room and

brings it into the room. If the outdoor temperature drops too low

, the air temperature at the

indoor outlet will co

rrespondingly be reduced. A

decrease in outdoor temperatures will result

in a decrease in heat output.

11.

Warm air

control (heat/ cool units only)

Under the HEAT mode (including

heat under

AUTO mode), the indoor fan speed is automatic-

ally reduced or stopped to prevent a cold

draft and the DEF

./PRE-DEF light will be

on if the

set temperature has not been reached. Under the following three situations:

Heating just starts

Defrosting has just finished

Outdoor temperature is

extremely low.

12. Three-minute protection

feature

After shutting the unit off ,there is a built in 3 minute protecti

on feature which will

not allow the

unit to restart unt

il the 3 minutes is reached.

1. Use a dry cloth to wipe the indoor unit and remote controlle

2. A cloth dam

pened with cold water ma

y be used on the in

door unit if it is very d

irty.

3. The indoor pa

nel can be rem

oved and cleaned with wa

ter. Wipe dry before reinstalli

ng on unit.

A clogged air filter redu

ces the cooli

ng efficiency of this unit. Plea

se clean the fil

ter once every

2 weeks.

1. T

o clean the air filt

er , lift the panel up to a fixed position

. It will click into position. Firm

ly grasp

the mid

dle of the filter an

d pull it downwards.

2. Remove the air freshening filter fro

m the mesh cle

aning filte

3. Use a vacuum cleaner to remove the du

st or wash the air fi

lter.

4. Clean the ai

r freshenin

g filter

ACTIVE CAR

BON FILTER/EL

ECTROSTA

TIC FILTER

clean the Carbon/Ele

ctrostatic filter, immerse in wa

ter with a MILD d

etergent for 20 minute

Wash the filter GENTLY(do not rub it clean) and place the filter under a la

mp for 3-4 hours to

dry. Replace the filter after cleaning it 4-5 times.

CLEANING

CLEANING THE AIR FILTER

CLEANING THE INDOOR UNIT

WARNING It is necessary to stop the air conditioner and disconnect the power supply

plug before cleaning.

CAUTION:

Do not use a chemically treated cloth or duster to clean the unit.

Do not use benzine, thinner, polishing powder, or similar solvents for cleaning. These may

cause the plastic surface to crack or deform.

£¡

Filter Handle

Panel

Air freshening filter

CLEANING

PARTS NAMES AND THEIR FUNCTIONS

INDOOR UNIT

OUTDOOR UNIT

Air outlet

Air-out

Air inlet

Air-in

OUTDOOR UNIT

NOTICE:

DISPLAY PANEL

INDOOR UNIT

Room temperature sensor (Inside front panel)

Front panel

Air inlet

Air filter (Inside the air inlet)

Horizontal air flow grille

Vertical air flow lever(Internal)

Display panel

Infrared signal receiver

Toggle type switch (Inside front panel)

Remote controller

Drain hose, refrigerant connecting pipe

Electric wiring

Stop valve

Air outlet

1. OPERATION indicator

This indicator flashes once every second after

power is on and illuminates when the air

conditioner is in operation.

2. ECONO. indicator

This indicator illuminates while the air

conditioner is in economic operation.

3. TIMER indicator

This indicator illuminates when TIMER is

set ON.

4. PRE-DEF indicator(cooling/heating only)

The air conditioner starts defrosting

automatically if outdoor unit frosts in heating

operation. At this time, PRE-DEF indicator

illuminates.

The indicator lights flash rapidly (five times per

second)when safety protection features come

into operation.

1. Your air conditioner may be

slightly different from the

above picture.

2. Cooling only type is without

PRE.-DEF indicator.

TIMER

OPERATION

ECONO.

PRE.-DEF.

NONPROBLEMATIC OPERATIONS

The following occurences do not mean the unit is malfunctioning.

1. Non- operation

The unit does

not work immediately after

the ON/OFF button is pushed.

The OPERA

TION light indicating normal

performance is on. However

, there is a compressor

protection built into the unit which does not

allow the unit to

start until the pressures have

equalized within the system.

This is approximately

a 3 minute delay

In Heat/Cool units only

, both the OPERATION light and PRE-DEF light is on at

the same

time and the unit is in the HEATING mode. The low ambient temperature will activate the

WARM

AIR CONTROL.

2. A white mist of chilled air is generated from

the indoor unit

Cooling in a room

with a high relative humidity ,especially combined with

the presence of high

levels of dust or

oil, causes an unstable room temperature. This is due to a build up of dirt

or dust

in the indoor unit .The unit should be cleaned by a qualified

servicer as soon as

possible.

3. Noise

hissing sound can be heard

during the defrost cycle or immediately after the cycle stops.

This is due to a change in

refrigerant flow between the indoor and outdoor units.

Due to the extreme

temperature fluctuations during operation

causing expansion or contraction

of the plastic parts

within the indoor unit, you may hear an

occasional squeaking noise.

4. Dust is blown out of the indoor unit.

This will occur

after an extended period of non-operation.

5. Bad odor is

coming out from the indoor unit.

This is because the indoor unit gives

off the smell impregnated from the wall,

furniture, or

smoking.

6. Turning to FAN

ONLY

while COOLING

To defrost the coil, the unit will switch to FAN ONLY mode automatically from time to time.

As the

coil defrosts, the unit will return to COOLING mode.

When the set room

temperature is reached, the

compressor will shut off and the unit will switch

into the F

AN ONLY mode. The compressor will restart and cooling will begin again

when the

room temperature increases.

7. Turn

to FAN

ONLY

while HEA

TING.

When the set room temperature is reached, the

compressor will shut of

f and the unit

will switch

into the F

AN ONLY mode. The compressor will restart and heating will begin again

when the

room temperature decreases.

8. During high humidity

conditions( 85% relative humidity or greater), the surface of the indoor unit

may sweat.

9. Defrosting operation (Cooling/Heating type only)

If the outdoor unit

is frosted during heating

operation, the heating output will be reduced.

this point ,the sensor

will sense the frost built up and the

control will shut of

f the fans. Heating

will resume after defrosting is finished.

HIGH

MODE

ING

TIMER

ECON

RES

LOC

LOW

AIR CONDITIONER OPERATION AND PERFORMANCE

AIR CONDITIONER OPERATING CONDITIONS

REMOTE CONTROLLER

Mode

Cooling operation

Heating operation

Drying operation

Temperature

1. If the air conditioner is used outside of the above conditions, certain safety protection

features may come into operation and cause the unit to function abnormally.

2. Room relative humidity less than 80%. If the air conditioner operates in excess of this

figure, the surface of the air conditioner may attract condensation. Please set the vertical

air flow louver to its maximum angle (vertically to the floor), and set HIGH fan mode.

Room temperature

Outdoor temperaure

Refer to REMOTE CONTROLLER MANUAL.

17 C o r m ore

18 C 43 C

30 C o r le ss

-7 C 24 C

17 C 32 C

11C 43C

CAUTION:

TEMPORARY OPERATION

Temporary switch

This function is used to operate the unit temporarily in case you misplace the remote

controller or its batteries are exhausted.

Open the panel and lift it up to a position angle

where it remains fixed. It will stop with a clicking

sound. Do not force the panel up any further.

Turn the switch to AUTO position and the air

conditioner will run under AUTO mode.

Close the panel firmly to its original position.

Remote control function can't be used while the

Indoor unit is in AUTO operation.

If you want to use remote control function, please

press AUTO switch on Indoor Unit Control Panel

again.

COOL switch on the Control Panel is only used in

Test Operation.

CAUTION:

NORMAL OPERATION

COOL

AUTO

CARE AND MAINTENANCE

TROUBLESHOOTING THE AIR CONDITIONER

If any of the following conditions occur, stop the air conditioner immediately, turn off the power

switch, and contact your dealer or servicer.

The indicator lights flash rapidly (five times per second). After disconnecting the

unit with the power source and after 3 minutes re-connecting to the power source,

the lights continue to flash.

The batteried in the remote controller

are exhausted.

The temperature setting is too high

or too low.

Does not

cool or

heat well

Does not

cool or

heat at all

The air filter is clogged with dust

Doors or windows are open

The air inlet or outlet of the outdoor

unit is blocked

The air inlet or outlet of the outdoor

unit is blocked

Clear up the block first, then begin to

operate.

Close the doors or windows

Clear up the block

Clean the filter

Set at a more comfortable temperature.

Wait or cancel timer setting

Change the batteries

Solutions

Cause

Problems

Inoperative

The timer is set.

Category

Problems

The fuse is blown frequently or the circuit breaker is tripped frequently.

Foreign matter or water has fallen inside the air conditioner.

Infrared signal receiver misfunctions or switch operations are erratic.

Any other unusual condition is observed.

Power failure

The power supply is disconnected.

The power fuse is blown.

Three-minute protection feature

Inappropriate temperature setting

Wait for a while

Set the temperature properly

Wait for restoring of power

Re-connect the power supply plug

Change the fuse

If a problem still exists, please contact your dealer. Make sure you provide the model and

serial number of the unit and a detailed description of the problem.

£¡

CAUTION:

To avoid personal injury, do not attempt to change the power wiring or service

the unit yourself.

Please move the vertical lever to adjust the

air-flow direction as required manually.

When the unit is operating and the horizontal louvers

are in a set position, to adjust the airflow simply take

hold of the left or right lever on the horizontal louvers

and re-adjust the louvers as required.

Please use the remote controller to adjust horizontal louvers so as to adjust the vertical

air flow direction.

Lever

The opening controlled by the horizontal louver should not be too narrow as this will

affect both cooling and heating efficiency.

Do not manually adjust the vertical louver or it may malfunction during operation.

lf the louver malfunctions, turn the unit off immediately and unplug it for several minutes.

Unit should function normally when re-energized.

Do not operate the air conditioner for long periods with the airflow direction set downward

during the cooling or drying operation as this may result in condensation forming on the

surface of the vertical louver and water dripping into the room.

When the air conditioner restarts, the vertical louver may remain in a set position for a short

period of time. This is normal.

During the initial unit break-in period, you may experience some noise when the horizontal

louver is turning. This is normal.

Please read this Owner s Manual carefully before operating the unit and strictly follow the

suggested operation methods. Failure to do so may result in serious damage to the unit and could

also cause personal injury or property damage.

Check that the ground wire is not broken off and that it is well secured.

Check that the air filter is installed correctly.

After a long period of non-use,make sure that the air filter is checked and cleaned. Refer to the

CARE AND MAINTENANCE section for details.

Be sure that air inlet and air outlet of the indoor and outdoor units are not blocked.

The following should be noted to ensure an economical operation. (Refer to corresponding

chapter for details)

Adjust the airflow direction away from your body.

Adjust the thermostat to a comfortable temperature range. Do not over cool or over heat the room.

ADJUSTING THE AIR FLOW DIRECTION

CHECKS BEFORE OPERATION

HINTS FOR ECONOMICAL OPERATION

Adjusting the Horizontal Air Flow

Adjusting the Vertical Air Flow

CAUTION:

PRECAUTION

£¡

While in the cooling mode, close the curtains to avoid direct sunlight entering and warming the room.

To keep cool or warm air in the room, avoid the unnecessary opening of doors and windows.

Set the timer for the desired operating time.

Never put obstructions near the air outlet or the air inlet as it will cause lower efficiency and may

even cause the unit to cease functioning.

To ensure heating and cooling efficiency, please clean the air filter once every two weeks.

Do not attempt to install this unit yourself. This unit requires installation by qualified persons.

For proper performance, always operate the unit under the usable operating temperature and

humidity conditions indicated in this Owner s Manual. Operating the unit beyond these conditions

could cause malfunctions such as condensation dripping from the indoor section.

Always maintain the room temperature at a comfortable level especially if there are children, elderly

people, or infirm people in the room.

In rare cases, the unit may temporarily experience erratic behaviour due to factors such as lightning

storms, running automobiles , or mobile phone use.

In the case of an interruption of power, please cut off the power supply to the unit, wait a few minutes,

and connect with the power supply again.

Please keep all electrical switches out of the reach of children.

If you plan to be away for an extended period of time, please disconnect the unit with the power

supply.

To prevent accident, turn off the power or disconnect the power supply plug before beginning

any cleaning or other routine maintenance.

When cleaning the unit use a soft, dry cloth. Do not use liquid cleaners or aerosol cleaners as

these might mar the finish. NEVER SPRINKLE WATER ON THE UNIT AS THIS MAY RESULT IN

ELECTRICAL SHOCK.

Never put hands or objects into the air outlet of indoor and outdoor units. These units contain

a fan running at high speed. Touching the moving fan will cause serious injury.

To avoid injury, never touch the grille while the airflow louver is running.

Do not remove the fan cover from the outdoor unit.

To avoid the risk of serious electrical shock, never sprinkle or spill water or liquid on either the

indoor unit or the remote controller.

To avoid the risk of fire, please keep inflammables such as hairspray, spray lacquer and

gasoline away from the air conditioner.

NEVER SERVICE THE UNIT YOURSELF. In case of any malfunction of the unit such as abnormal

noises or sounds, abnormal smells, fog in the room, high temperatures, water dripping, etc.,please

turn off the power and contact your dealer or servicer.

Do not allow young children to operate this unit.

SAFETY INFORMATION

CAUTION

WARNING

DANGER

£¡

R51/E-30

REMOTE CONTROLLER

OWNERSM ANUAL

CONTENTS

Remote Controller Specifications---------------------------------------

Performance Features-----------------------------------------------------

Introduction of Function Buttons on the Remote Controller---

Names and Functions of indicators on Remote Controller----

Operating the Remote Controller---------------------------------------

Warning--------------------------------------------------------------------------

1. Be sure there are no barriers between the remote controller and

the receiver of indoor unit otherwise the air conditioner will not

work.

2. Keep the Remote Controller away from all liquids.

3. Protect the Remote Controller from high temperatures and exposure

to radiation.

4. Keep the indoor receiver out of direct sunlight or the Air Conditioner

may malfunction.

5. Keep controller away from EMI (Electro-Magnetic Interference)

supplied by other household appliances.

Warning

2. To set the STOPPING time.

3. Set the STARTING & STOPPING time

Model

R51, R51/BG,R51/E,R51/CE,R51/BGE,R51/CBGE

Environment

Temperature Range

Reaching Distance

Lowest Voltage of CPU

Emitting Signal

Rated Voltage

-5 C 60 C

8m (when using 3.0 voltage, it Gets 11m)

3.0V

2.0V

Remote Controller Specifications

Performance Features

Introduction of Function Buttons on the Remote Controller

1. Operating Mode: COOL HEAT DRY FAN and AUTO .

2. Timer Setting Function in 24 hours.

3. Indoor Setting Temperature Range : 17 C~30 C.

4. LCD (Liquid Crystal Display) of all functions.

5. Night Light Function (only R51/BG model available)

6. Compatible with the former R11.

2.1 Please press the CANCEL button to cancel any former settings.

2.3 Push the TEMP button to cancel the TIMER ON setting. The

digital area will show "00".

2.6 After setting the TIMER there will be a one-half second delay before

the remote controller transmits the signals to the Air Conditioner.

Then after approximately another 2 seconds, the set temperature

will re-appear on the digital display.

3.1 Please press the CANCEL button to cancel any former settings.

3.2 Push the TIMER button and the remote controller will show the

last set time for START operation and the signal "h" will

be shown on the display panel. You are now ready to readjust

the TIMER ON to start the operation.

3.3 Push the TEMP button ( or ) to set the time you want to

start the operation.

3.4 Push the TIMER button and the remote controller will show

the last set time for STOP operation and the signal "h" will be

shown on the display panel. You are now ready to reset the

time of the STOP operation.

3.5 Push the TEMP button ( or ) to set the time you want to

stop the operation.

3.6 After setting the TIMER there will be a one-half second delay

before the remote controller transmits the signal to the Air

Conditioner. Then, after approximately another 2 seconds ,the

set temperature will re-appear on the digital display.

2.5 Push the TEMP button ( or ) to set the time you want to

stop the operation.

2.4 Push the TIMER button and the remote controller will show the last

set time for the STOP operation and the signal "h" will be shown

on the display panel. You are now ready to reset the time of the

STOP operation.

2.2 Push the TIMER button and the remote controller will show the

last set time for the START operation and the signal "h"

will be shown on the display panel. You are now ready to re-

adjust the TIMER OFF to stop the operation.

NOTE

1. Please reset the TIMER after cancelling the former time

settings.

2. The setting time is relative time. That is the time set is based on

the delay of the current time.

CANCEL

LOCK

Fig. 1

SET TEMPERATURE

AUTO

COOL

DRY

HEAT

FAN

HIGH

MED

LOW

TEMP

MODE

SWING

TIMER

RESET

ON/OFF

FAN SPEED

ECONOMIC RUNNING

VENT

1. If the AUTO mode is not comfortable , you may manually override

the settings by using COOL, DRY, HEAT( HEAT PUMP units only),

or FAN ONLY modes.

2. Push the TEMP button to set the desired room temperature.

When in COOLING mode, the most comfortable settings are 21 C

or above. When in HEATING mode, the most comfortable settings

are 28 C or b elow.

3. Push the FAN SPEED to select the FAN mode of AUTO, HIGH,

MED or LOW.

4. Push the ON/OFF button. The operation lamp lights and the air

conditioner starts to operate per your settings. Push the ON/OFF

button again to stop this unit operation.

The FAN ONLY mode cannot be used to control the temperature. While

in this mode, only steps 1 3 and 4 may be performed.

COOL , HEAT, and FAN ONLY Operation

NOTE

Due to the difference of the set temperature of the unit and the

actual indoor temperature, the Air Conditioner when in DRY mode

will automatically operate many times without running the COOL

and FAN mode.

1. Push the MODE button to select DRY.

2. Push the TEMP button to set the desired temperature from

21 C to 2 8 C.

3. Push the ON/OFF button. The operation lamp lights and the air

conditioner starts to operate in the DRY mode. Push the ON/OFF

button again to stop this unit operation.

DRY OPERATION

NOTE

PUSH TIMER button to set the on and off times of the unit.

1.1 Please push the CANCEL button to cancel any former settings.

1.2 Push the TIMER button. The remote controller will show the

TIMER and the signal "h" is shown on the display panel. The

control is now ready to reset the TIMER ON to start the operation.

1.3 Push the TEMP button ( or ) to set desired unit START

time .

1.4 After setting the TIMER there will be a one-half second delay

before the remote controller transmits the signal to the Air

Conditioner. Then, after approximately another 2 seconds ,the

set temperature will re-appear on the digital display.

TIMER OPERATION

1. To set the STARTING time.

TEMP Button : Push the TEMP button to decrease the indoor

temperature setting or to adjust the TIMER in a counter-clockwise

direction.

MODE Select Button: Each time you push the button, a mode is

selected in a sequence that goes from AUTO COOL DRY

HEAT and FAN as the following figure indicates:

SWING Button: Push this switch button to change the louver

angle .

RESET Button: When the RESET button is pushed, all of the current

settings are cancelled and the control will return to the initial settings.

NOTE: HEAT only for Heat Pump

AUTO

COOL

DRY

HEAT FAN

LOCK Button: Push this button to lock in all the current settings. To

release settings, push again.

CANCEL Button: Push this button to cancel the TIMER settings.

TIMER Button: This button is used to preset the time ON (start

to operate) and the time OFF (turn off the operation).

ON/OFF Button: Push this button to start the unit operation. Push

the button again to stop the unit operation.

FAN SPEED Button: This button is used for setting Fan Speed in

the sequence that goes from AUTO LOW MED to HIGH, then

back to Auto.

TEMP Button : Push the button to increase the indoor temperature

setting or to adjust the TIMER in a clockwise direction.

VENT Button : Push this button to set the ventilating mode. The

ventilating mode will operate in the following sequence :

Auto Off

Continuous

Ventilation Function is available for the Fresh Star Series.

ECONOMIC RUNNING Button: Push this button to go into the

Energy-Saving operation mode.

Names and Functions of indicators on Remote Controller

TRANSMISSION Indicator: This indicator lights when remote

controller transmits signals to indoor unit.

MODE Display: Shows the current operation modes-- AUTO,

COOL, DRY and HEAT. HEAT only available for heat pump model.

HEAT PUMP ONLY - LOCK display is displayed by pushing the LOCK

button. Push the LOCK button again to clear display.

TIMER Display: This display area shows the settings of TIMER.

That is, if only the starting time of operation is set, it will display the

TIMER ON. If only the turning off time of operation is set, it will display

the TIMER OFF. If both operations are set, it will show TIMER ON OFF

which indicates you have chosen to set both the starting time and off

time.

FAN Display: When the FAN button is pushed, this signal indicator lights.

Digital Display Area: This area will show the temperature and, if in the

TIMER mode, will show the ON and OFF settings of the TIMER.

NOTE: All items are shown in the Fig.2 for the purpose of clear

presentation But during the actual operation only the re-

lative functional items are shown on the display panel.

Display Panel

Fig. 2

AUTO

COOL

DRY

HEAT

3 4

FAN

HIGH

MED

LOW

Operating the Remote Controller

The Remote Controller uses two alkaline dry batteries(R03/Ir03X2).

When the Air Conditioner is ready for use, switch on the power

and the OPERATION indicator lamp on the display panel of the

indoor unit starts flashing.

1. Use the MODE select button to select AUTO.

2. Push the TEMP button to set the desired room temperature.

The most comfortable temperature settings are between 21 C

to 28 C.

3. Push the ON/OFF button to start the air conditioner. The OPE-

RATION lamp on the display panel of the indoor unit lights. The

operating mode of AUTO FAN SPEED is automatically set and

there are no indicators shown on the display panel of the remote

controller.

4. Push the ON/OFF button again to stop the unit operation.

1. To install batteries, slide back the cover of the battery compartment

and install the batteries according to the directions (+and -) shown

on the Remote Controller.

2. To replace the old batteries , use the same method as mentioned

above.

1. When replacing batteries, do not use old batteries or a different

type battery. This may cause the remote controller to

malfunction.

2. If you do not use the remote controller for several weeks

remove the batteries. Otherwise battery leakage may damage

the remote controller.

3. The average battery life under normal use is about 6 months.

4. Replace the batteries when there is no answering beep from the

indoor unit or if the Transmission Indicator light fails to appear.

1. In the AUTO mode, the air conditioner can logically choose

the mode of COOL, FAN, HEAT and DRY by sensing the dif-

ference between the actual ambient room temperature and

the set temperature on the remote controller..

2. If the AUTO mode is not comfortable for you , the desired mode

can be selected manually.

Install / Replace Batteries

AUTOMATIC OPERATION

NOTE

AEG Electrolux esa185bgmb-i User manual

Brand: AEG Electrolux

Model: esa185bgmb-i

Type: User manual

This manual is also suitable for

ESA185BGMB/E

Download PDF

report

AEG Electrolux esa185bgmb-i User manual

This manual is also suitable for

AEG Electrolux esa185bgmb-i User manual

Related papers

Other documents