Electrolux EWF10190W User manual

Category
Washing machines
Type
User manual
user manual
Washing Machine
EWF 10190 W
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Contents
Safety information 2
Product description 4
Control panel 5
First use 6
Daily use 7
Washing programmes 9
Helpful hints and tips 12
Care and cleaning 13
What to do if… 17
Technical data 19
Consumption values 19
Installation 20
Electrical connection 23
Environment concerns 23
Subject to change without notice
Safety information
Important! Read carefully & keep for future
reference.
The safety of Your appliance complies with
the industry standards and with legal re-
quirements on the safety of appliances.
However, as manufacturers, we feel it is
our duty to provide the following safety
notes.
It is most important that this instruction
book should be retained with the appli-
ance for future reference. Should the ap-
pliance be sold or transferred to another
owner, or should you move house and
leave the appliance, always ensure that the
book is supplied with the appliance in or-
der that the new owner can get to know
the functioning of the appliance and the
relevant warnings.
You MUST read them carefully before in-
stalling or using the appliance.
Before first starting up, check the appli-
ance for any damage incurred during
transport. Never connect up a damaged
appliance . If parts are damaged, contact
your supplier.
If the appliance is delivered in the winter
months when there are minus tempera-
tures. Store it at room temperature for 24
hours before using for the first time.
General safety
It is dangerous to alter the specifications or
attempt to modify this product in any way.
During high temperature wash pro-
grammes the door glass may get hot. Do
not touch it!
Make sure that small pets do not climb into
the drum. To avoid this, please check into
the drum before using.
Any objects such as coins, safety pins,
nails, screws, stones or any other hard,
sharp material can cause extensive dam-
age and must not be placed into the ma-
chine.
Only use the advised quantities of fabric
softener and detergent. Damage to the
fabric can ensue if you over-fill. Refer to the
manufacturer’s recommendations of
quantities.
Wash small items such as socks, laces,
washable belts etc in a washing bag or pil-
low case as it is possible for such items to
slip down between the tub and the inner
drum.
Do not use your washing machine to wash
articles with whalebones, material without
hems or torn material.
Always unplug the appliance and turn off
the water supply after use, cleaning and
maintenance.
Under no circumstances should you at-
tempt to repair the machine yourself. Re-
pairs carried out by inexperienced people
may cause injury or serious malfunction-
ing. Contact your local Service Centre. Al-
ways insist on genuine spare parts.
Installation
This appliance is heavy. Care should be
taken when moving it.
When unpacking the appliance, check that
it is not damaged. If in doubt, do not use it
and contact the Service Centre.
2 electrolux
All packing and transit bolts must be re-
moved before use. Serious damage can
occur to the product and to property if this
is not adhered to. See relevant section in
the user manual.
After having installed the appliance, check
that it is not standing on the inlet and drain
hose and the worktop is not pressing the
electrical supply cable against the wall.
If the machine is situated on a carpeted
floor, please adjust the feet in order to al-
low air to circulate freely under the appli-
ance.
Always be sure, that there is no water leak-
age from hoses and their connections after
the installation.
If the appliance is installed in a location
subject to frost, please read the “dangers
of freezing” chapter.
Any plumbing work required to install this
appliance should be carried out by a quali-
fied plumber or competent person.
Any electrical work required to install this
appliance should be carried out by a quali-
fied electrician or competent person.
Use
This appliance is designed for domestic
use. It must not be used for purposes other
than those for which it was designed.
Only wash fabrics which are designed to
be machine washed. Follow the instruc-
tions on each garment label.
Do not overload the appliance. See the
Washing Programme Table.
Before washing, ensure that all pockets
are empty and buttons and zips are fas-
tened. Avoid washing frayed or torn arti-
cles and treat stains such as paint, ink,
rust, and grass before washing. Under-
wired bras must NOT be machine washed.
Garments which have been in contact with
volatile petroleum products should not be
machine washed. If volatile cleaning fluids
are used, care should be taken to ensure
that the fluid is removed from the garment
before placing in the machine.
Never pull the power supply cable to re-
move the plug from the socket; always
take hold of the plug itself.
Never use the appliance if the power sup-
ply cable, the control panel, the working
surface or the base are damaged so that
the inside of the washing machine is ac-
cessible.
Child safety
This appliance is not intended for use by
person (including children) with reduced
physical sensory or mental capabilities or
lack of experience and knowledge unless
they have been given supervision or in-
struction concerning use of the appliance
by a person responsible for their safety.
The packaging components (e.g. plastic
film, polystyrene) can be dangerous to chil-
dren - danger of suffocation! Keep them
out of children’s reach.
Keep all detergents in a safe place out of
children’s reach.
Make sure that children or pets do not
climb into the drum. To prevent children
and pets becoming trapped inside the
drum the machine incorporates a special
feature. To activate this device, rotate the
button (without pressing it) inside the door
clockwise until the groove is horizontal. If
necessary use a coin.
To disable this device and restore the pos-
sibility of closing the door, rotate the but-
ton counterclockwise until the groove is
vertical.
electrolux 3
Product description
Your new appliance meets all modern requirements for effective treatment of laundry
with low water, energy and detergent consumption. Its new washing system allows total
use of detergent and reduces water consumption so saving energy.
1 2
3
4
5
6
1 Detergent dispenser drawer
2 Control panel
3 Door opening handle
4 Rating Plate
5 Drain pump
6 Adjustable feet
Detergent dispenser drawer
Compartment for detergent used for pre-
wash and soak phase or for stain remover
used during the stain action phase (if availa-
ble). The prewash and soak detergent is
added at the beginning of the wash pro-
gramme. The stain remover is added during
the stain action phase.
Compartment for powder or liquid deter-
gent used for main wash. If using liquid de-
tergent pour it just before starting the pro-
gramme.
Compartment for liquid additives (fabric
softener, starch).
Follow the product manufacturer’s recom-
mendations on quantities to use and do not
exceed the «MAX» mark in the detergent
dispenser drawer. Any fabric softener or
starching additives must be poured into the
compartment before starting the wash pro-
gramme.
4 electrolux
Control panel
Below is a picture of the control panel. It shows the programme selector dial as well as
the temperature selector dial, the buttons and the pilot lights. These are presented by
relevant numbers on the following pages.
1 2 3 4 5 6 7 8
1 Programme selector dial
2
Temperature selector dial (TEMPER-
ATURA)
3 Spin reduction button (CENTRIFU-
GADO)
4 Options button (OPCIONES)
5 Extra Rinse button (AQUACARE)
6
Start/Pause button (INICIO/PAUSA)
7 Delay Start button (INICIO DIFERIDO)
8 Indicator Pilot Lights
Table of Symbols
= Aqua en cuba = Prewash
= Sin centrifugado = Económico
= Cold = Rapido
Pilotos indicadores
= Washing
= Door locked
= End of Cycle
Programme Selector Dial
It allows you to switch the appliance on/off
and/or to select a programme.
Temperature selector dial
This dial allows you to select the temperature
more suitable to the laundry to be washed.
By selecting the position
the machine will
wash with cold water.
electrolux 5
CENTRIFUGADO
By pressing this button you can reduce the
maximum spin speed allowed for the selec-
ted programme or to select the available op-
tion(s).
SIN CENTRIFUGADO
By selecting this option, all spinning phases
are suppressed and replaced by a drain, so
as not to wrinkle the laundry. Recommended
for extremely delicate fabrics. On some pro-
grammes the rinses will be performed with
more water.
AGUA EN CUBA
By selecting this function the water of the last
rinse is not emptied out to prevent the fabrics
from creasing. Before opening the door it will
be necessary to empty out the water. To
empty out the water, please read the para-
graph «At the end of the programme».
PRELAVADO
By selecting this option the machine per-
forms a prewash cycle before the main wash
phase. The washing time will be prolonged.
This option is recommended for heavily
soiled laundry.
ECONÓMICO
Only for cottons and synthetic items lightly or
normally soiled at a temperature of 40°C or
higher. The washing time will be prolonged
and the washing temperature will be re-
duced. You can use this option if you want
to wash normally soiled laundry and at the
same time save energy.
RAPIDO
Short cycle for lightly soiled items or for laun-
dry which needs only freshening up. We rec-
ommend you to reduce the fabrics loading.
AQUACARE
This appliance is designed for saving energy.
If it necessary to rinse the laundry using an
extra quantity of water select this option.
Some additional rinses will be performed.
This option is recommended for people who
are allergic to detergents, and in areas where
the water is very soft.
INICIO DIFERIDO
The start of the programme can be delayed
by 2, 4 or 8 hours by means of this button.
INICIO/PAUSA
This button allows you to start or to interrupt
the selected programme.
Indicator pilot lights
8.1
8.2
8.3
After having pressed the button 6 , the pilot
light 8.1 (Washing) illuminates. When the pilot
light 8.1 (Washing) comes on this means that
the machine is operating.
The pilot light 8.2 (Door locked) illuminates
when the programme starts and indicates if
the door can be opened.
- light on: the door cannot be opened;
- light off: the door can be opened;
- light flashing: the door is opening.
When the programme has finished the pilot
light 8.3 (End) comes on.
First use
Ensure that the electrical and water
connections comply with the installa-
tion instructions.
Remove the polystyrene block and
any material from the drum.
Pour 2 liters of water into the main
wash compartment
of the deter-
gent drawer in order to activate the
ECO valve. Then run a cotton cycle at
the highest temperature without any
laundry in the machine, to remove any
6 electrolux
manufacturing residue from the drum
and tub. Pour 1/2 a measure of de-
tergent into the main wash compart-
ment and start the machine.
Daily use
Load the laundry
Open the door by carefully pulling the door
handle outwards. Place the laundry in the
drum, one item at a time, shaking them out
as much as possible. Close the door.
Measure out the detergent and the fab-
ric softener
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent re-
quired, pour it into the main wash compart-
ment
or in the appropriate compartment
if the selected programme/option it requires
(see more details in «Detergent dispenser
drawer»).
If required, pour fabric softener into the com-
partment marked
(the amount used must
not exceed the «MAX» mark in the drawer).
Close the drawer gently.
Select the required programme by
turning the programme selector dial (1)
Turn the programme selector dial to the re-
quired programme. The washing machine
will automatically select the maximum spin
value provided for the programme you have
chosen. You can change this value by press-
ing the corresponding button. The green pi-
lot light of the button 6 starts to flash.
electrolux 7
The selector dial can be turned either clock-
wise or counterclockwise. Turn to position
« O » to reset programme/Switching the ma-
chine off.
At the end of the programme the selec-
tor dial must be turned to position O, to
switch the machine off.
Caution! If you turn the programme
selector dial to another programme
when the machine is working, the red
pilot light of button 6 will blink 3 times to
indicate a wrong selection. The machine
will not perform the new selected
programme.
Select the required temperature by
turning the temperature selector dial (2)
Turn clockwise this dial to select the more
convenient to your laundry washing temper-
ature.
Reduce the spin speed by pressing
button 3
By selecting a programme, the appliance
proposes automatically the maximum spin
speed provided for that programme.
Press button 3 repeatedly to change the spin
speed, if you want your laundry to be spun at
a different speed. The relevant light illumi-
nates.
Select the available options by pressing
buttons 3, 4 and 5
Depending on the programme, different
functions can be combined. These must be
selected after choosing the desired pro-
gramme and before starting the programme.
When these buttons are pressed, the corre-
sponding pilot lights illuminate. When they
are pressed again, the pilot lights go out. If
an incorrect option is selected, the integrated
red pilot light of the button 6 flashes for 3
times.
For the compatibility among the washing
programmes and the options see chap-
ter «Washing Programmes».
Select the Delay Start by pressing
button 7
Before you start the programme, if you wish
to delay the start, press the button 7 repeat-
edly, to select the desired delay. The relevant
light illuminates.
You must select this option after you have set
the programme and before you start the pro-
gramme.
You can cancel or modify the delay time at
any moment, before you press button 6 .
Selecting the delayed start:
1. Select the programme and the required
options.
2. Select the delay start by pressing the but-
ton 7 .
3.
Press button 6 :
the machine starts its hourly count-
down.
The programme will start after the se-
lected delay has expired.
Cancelling the delayed start after having star-
ted the programme:
1. Set the washing machine to PAUSE by
pressing button 6 .
2.
Press button 7 once, the light relevant to
the selected delay goes off
3. Press button 6 again to start the pro-
gramme.
The Delay Start can not be selected with
DRAIN programme.
Important! The selected delay can be
changed only after selecting the washing
programme again.
The door will be locked throughout the delay
time. If you need to open the door, you must
set the machine to PAUSE (by pressing the
button 6 ) and then wait a few minutes. After
you have closed the door, press the button
6 again.
Start the programme by pressing button
6
To start the selected programme, press the
button 6 , the corresponding green pilot light
stops blinking. The pilot lights 8.1 and 8.2
illuminate to indicate that the appliance starts
operating and the door is locked.
To interrupt a programme which is running,
press the button 6 : the corresponding green
pilot light starts blinking.
To restart the programme from the point at
which it was interrupted, press the button 6
again . If you have chosen a delayed start,
the machine will begin the countdown.
If an incorrect option is selected, the red pilot
light of the button 6 blinks for 3 times.
8 electrolux
Altering an option or a running
programme
It is possible to change some options before
the programme carries them out.
Before you make any change, you must
PAUSE the appliance by pressing the button
6 .
Changing a running programme is possible
only by resetting it. Turn the programme se-
lector dial to O and then to the new pro-
gramme position. Start the new programme
by pressing the button 6 again. The washing
water in the tub will be not emptied out.
Interrupting a programme
Press the button 6 to interrupt a programme
which is running, the corresponding green
pilot light starts blinking.
Press the button again to restart the pro-
gramme.
Cancelling a programme
Turn the selector dial to
to cancel a pro-
gramme which is running.
You can select now a new programme.
Opening the door
After the programme has started (or during
the delay time) the door is locked, if you need
to open it, set first the machine to PAUSE by
pressing the button 6 . After a few minutes
the light 8.2 goes out and it is possible to
open the door.
If this light remains lit and the door is locked,
this means that the machine is already heat-
ing or that the water level is too high. In any
case, do not try to force the door!
If you cannot open the door but you need to
open it you have to switch the machine off by
turning the selector dial to O . After a few mi-
nutes the door can be opened (pay atten-
tion to the water level and tempera-
ture!) .
After closing the door, it is necessary to se-
lect the programme and options again and to
press button 6 .
At the end of the programme
The machine stops automatically. The pilot
light of button 6 , the pilot lights 8.1 and
8.2 go off. The light 8.3 illuminates.
If a programme or an option that ends with
water left in the tub has been selected, the
pilot light 8.2 remains on and the door is
locked to indicate that the water must be
emptied out before opening the door.
Follow the below instructions to empty out
the water:
1.
Turn the programme selector dial to O .
2. Select the draining or spinning pro-
gramme.
3. Reduce the spin speed if needed, by
pressing the relevant button.
4. Press button 6 .
At the end of the programme, the light 8.2
goes off to indicate that the door can be now
opened. Turn the programme selector dial to
O to switch the machine off.
Remove the laundry from the drum and care-
fully check that the drum is empty. If you do
not intend to carry out another wash, close
the water tap. Leave the door open to pre-
vent the formation of mildew and unpleasant
smells.
Washing programmes
Programme - Maximum and Minimum Tempera-
ture - Cycle Description - Maximum Spin Speed -
Maximum Fabrics Load - Type of Laundry
Options
Detergent
Compartment
ALGODÓN
90° - Cold
1)
Main wash - Rinses
Maximum spin speed 1000 rpm
Max. load 8 kg - Red. load 4 kg
2)
White and coloured cotton (heavily or normally soiled
items).
SPIN REDUCTION
SIN CENTRIFUGADO
AQUA EN CUBA
PREWASH
3)
ECONÓMICO
RAPIDO
AQUACARE
electrolux 9
Programme - Maximum and Minimum Tempera-
ture - Cycle Description - Maximum Spin Speed -
Maximum Fabrics Load - Type of Laundry
Options
Detergent
Compartment
SINTÉTICOS
60° - Cold
Main wash - Rinses
Maximum spin speed 900 rpm
Max. load 4 kg - Red. load 2 kg
2)
Synthetic or mixed fabrics (normally soiled items)
SPIN REDUCTION
SIN CENTRIFUGADO
AQUA EN CUBA
PREWASH
3)
ECONÓMICO
RAPIDO
AQUACARE
PLANCHA FÁCIL
60° - Cold
Main wash - Rinses
Maximum spin speed 900 rpm
Max. load 1 kg
This programme can be selected for synthetic items
and mixed fabrics to be ironed. The laundry can be
gently washed and spun to avoid any creasing. In this
way ironing is easier. Furthermore the machine will per-
form additional rinses.
SPIN REDUCTION
SIN CENTRIFUGADO
AQUA EN CUBA
PREWASH
3)
AQUACARE
DELICADOS
40° - Cold
Main wash - Rinses
Maximum spin speed 700 rpm
Max. load kg 4 - Red. load kg 2
2)
Delicate fabrics: acrylics, viscose, polyester.
SIN CENTRIFUGADO
AQUA EN CUBA
PREWASH
3)
RAPIDO
AQUACARE
LANA
40° - Cold
Main wash - Rinses
Maximum spin speed 1000 rpm
Max. load 2 kg
Washing programme for machine washable wool as
well as for hand washable woollens and delicate fab-
rics. Note : A single or bulky item may cause imbalance.
If the appliance doesn’t perform the final spin phase,
add more items, redistribute the load manually and then
select the spinning programme.
SPIN REDUCTION
SIN CENTRIFUGADO
AQUA EN CUBA
A MANO
40° - Cold
Main wash - Rinses
Maximum spin speed 1000 rpm
Max. load 2 kg
Special programme for delicate fabrics with "hand
washing" care symbol.
SPIN REDUCTION
SIN CENTRIFUGADO
AQUA EN CUBA
SEDA
30°
Main wash - Rinses
Maximum spin speed 700 rpm
Max. load 1 kg
Delicate washing programme suitable for silk and
mixed synthetic items.
SIN CENTRIFUGADO
AQUA EN CUBA
10 electrolux
Programme - Maximum and Minimum Tempera-
ture - Cycle Description - Maximum Spin Speed -
Maximum Fabrics Load - Type of Laundry
Options
Detergent
Compartment
REMOJO
30°
Prewash - Soak for about 40 minutes - Stop with water
in the tub
Max. load 8 kg
Special programme for heavily soiled laundry. The ma-
chine performs a soak at 30°C. At the end of this time
the machine will stop automatically with water left in the
tub.
Before starting a new washing phase, it is necessary to
empty out the water by:
Draining only : turn the programme selector dial to
draining programme (press then the button 6 ).
Draining and spinning : turn the programme se-
lector dial to the spinning programme, reduce the
spin speed by pressing the relevant button, and then
press button 6 .
Important! This programme cannot be used for very
delicate fabrics as silk or wool. Pour the detergent for
the soak programme into the appropriate compart-
ment. At the end of the soak (after having emptied out
the water) you can select the washing programme (first-
ly turn the programme selector dial to O , then to the
programme and press the button 6 ).
MINI
30°
Main wash - Rinses
Maximum spin speed 700 rpm
Max. load 2 kg
Complete programme for slightly soiled items which
need to be freshened up.
SIN CENTRIFUGADO
ACLARADOS
Rinses with fabric softener if needed
Maximum spin speed 1000 rpm
Max. load 8 kg
With this programme it is possible to rinse and spin
cotton garments which have been washed by hand.
The machine performs 3 rinses, followed by a final long
spin. The spin speed can be reduced by pressing the
relevant button.
SPIN REDUCTION
SIN CENTRIFUGADO
AQUA EN CUBA
AQUACARE
ACLARADO DELICADO
Rinse with fabric softener if needed
Maximum spin speed 700 rpm
Max. load 4 kg
With this programme it is possible to rinse and spin
garments which have been washed by hand. The ma-
chine performs a rinse, followed by a final short spin.
SPIN REDUCTION
SIN CENTRIFUGADO
AQUA EN CUBA
AQUACARE
DESCARGA
Draining of water
Max. load 8 kg
For emptying out the water of the last rinse in pro-
grammes/option selected which end with water left in
the tub or at the end of the Soak programme.
electrolux 11
Programme - Maximum and Minimum Tempera-
ture - Cycle Description - Maximum Spin Speed -
Maximum Fabrics Load - Type of Laundry
Options
Detergent
Compartment
CENTRIFUGADO
Drain and long spin
Maximum spin speed 1000 rpm
Max. load 8 kg
Separate spin for hand washed garments and after
programmes with option selected which ends with wa-
ter left in the tub. You can choose the spin speed by
pressing the relevant button to adapt it to the fabrics to
be spun.
SPIN REDUCTION
CENTRIFUGADO DELICADO
Drain and short spin
Maximum spin speed 700 rpm
Max. load 4 kg
Separate spin for hand washed garments and after
programmes with option selected which ends with wa-
ter left in the tub.
O = OFF
For cancelling the programme which is running or to
switch the machine off .
1) This programme at the temperature of 60° with the option ECONÓMICO selected, is the reference
programme for the data entered in the energy label, in compliance with EEC 92/75 standards. It can
be selected for slightly or normally soiled cotton items. The temperature will decrease and the washing
time will be extended. This allows to obtain a good washing efficiency so saving energy.
2) If you select the RAPIDO option by pressing button 4 , we recommend that you reduce the maximum
load as indicated. (Red. load = reduced load). Full loading is possible however with somewhat reduced
cleaning results.
3) If using liquid detergents, a programme without PREWASH must be selected.
Helpful hints and tips
Sorting out the laundry
Follow the wash code symbols on each gar-
ment label and the manufacturer’s washing
instructions. Sort the laundry as follows:
whites, coloureds, synthetics, delicates,
woollens.
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the
wash.
New coloured items may run in the first wash;
they should therefore be washed separately
the first time.
Button up pillowcases, close zip fasteners,
hooks and poppers. Tie any belts or long
tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special
detergent or detergent paste.
Treat curtains with special care. Remove
hooks or tie them up in a bag or net.
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable
to treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
special detergent then rub in the soap and
water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with turpen-
tine, lay the garment on a soft surface and
dab the stain with the fingertips and a cotton
cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
12 electrolux
cellulose structure will already have been
damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with ace-
tone
1)
, lay the garment on a soft cloth and
dab the stain.
Lipstick: moisten with acetone as above,
then treat stains with methylated spirits.
Treat any residual marks with bleach.
Red wine: soak in water and detergent,
rinse and treat with acetic or citric acid, then
rinse. Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten
the fabric first with acetone
1)
, then with acetic
acid; treat any residual marks on white fab-
rics with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, me-
thylated spirits or benzine, then rub with de-
tergent paste.
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the en-
vironment.
Although biodegradable, detergents contain
substances which, in large quantities, can
upset the delicate balance of nature.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
etc.), the colour, washing temperature and
degree of soiling.
All commonly available washing machine de-
tergents may be used in this appliance:
powder detergents for all types of fabric
powder detergents for delicate fabrics
(60°C max) and woollens
liquid detergents, preferably for low tem-
perature wash programmes (60°C max)
for all types of fabric, or special for wool-
lens only.
The detergent and any additives must be
placed in the appropriate compartments of
the dispenser drawer before starting the
wash programme.
If using liquid detergents, a programme
without prewash must be selected.
Your appliance incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Follow the product manufacturer’s recom-
mendations on quantities to use and do not
exceed the «MAX» mark in the detergent
dispenser drawer .
Quantity of detergent to be used
The type and quantity of detergent will de-
pend on the type of fabric, load size, degree
of soiling and hardness of the water used.
Follow the product manufacturers’ instruc-
tions on quantities to use.
Use less detergent if:
you are washing a small load
the laundry is lightly soiled
large amounts of foam form during wash-
ing.
Degrees of water hardness
Water hardness is classified in so-called “de-
grees” of hardness. Information on hardness
of the water in your area can be obtained
from the relevant water supply company, or
from your local authority. If the water hard-
ness degree is medium or high we suggest
you to add a water softener following always
the manufacturer’s instructions. When the
degree of hardness is soft, readjust the quan-
tity of the detergent.
Care and cleaning
Warning! You must disconnect the
appliance from the electricity supply,
before you can carry out any cleaning or
maintenance work.
Descaling
The water we use normally contains lime. It
is a good idea to periodically use a water
softening powder in the machine. Do this
separately from any laundry washing, and
according to the softening powder manufac-
1) do not use acetone on artificial silk
electrolux 13
turer's instructions. This will help to prevent
the formation of lime deposits.
After each wash
Leave the door open for a while. This helps
to prevent mould and stagnant smells form-
ing inside the appliance. Keeping the door
open after a wash will also help to preserve
the door seal.
Maintenance wash
With the use of low temperature washes it is
possible to get a build up of residues inside
the drum.
We recommend that a maintenance wash be
performed on a regular basis.
To run a maintenance wash:
The drum should be empty of laundry.
Select the hottest cotton wash pro-
gramme.
Use a normal measure of detergent, must
be a powder with biological properties.
External cleaning
Clean the exterior cabinet of the appliance
with soap and water only, and then dry thor-
oughly.
Important! Do not use methylated spirits,
solvents or similar products to clean the
cabinet.
Cleaning the dispenser drawer
The detergent dispenser drawer should be
cleaned regularly.
1. Remove the detergent dispenser drawer
by pulling it firmly. Remove any traces of
accumulated powder. To aid cleaning,
the top part of the additive compartment
should be removed.
2. Remove the conditioner insert from the
appropriate compartment.
3. Clean all parts with water.
4. Put the conditioner insert in as far as it will
go, so that it is firmly in place
5. Clean all parts of the machine, especially
the nozzles in the top of the washing-in
chamber, with a brush.
14 electrolux
6. Insert the detergent dispenser drawer in
the guide rails and push it in.
Washing drum
Rust deposits in the drum may occur due to
rusting foreign bodies in the washing or tap
water containing iron.
Important! Do not clean the drum with
acidic descaling agents, scouring agents
containing chlorine or iron or steel wool.
1. Remove any rust deposits on the drum
with a cleaning agent for stainless steel.
2. Run a washing cycle without any washing
to clean off any cleaning agent residues.
Programme: Short Cotton Programme at
maximum temperature and add approx.
1/4 measuring cup of detergent.
Door seal
Check from time to time the door seal and
eliminate eventual possible objects that
could be trapped in the fold.
Drain pump
The pump should be inspected regularly and
particularly if:
the machine does not empty and/or spin
the machine makes an unusual noise dur-
ing draining due to objects such as safety
pins, coins etc. blocking the pump.
Proceed as follows:
1. Disconnect the appliance.
2. If necessary wait until the water has
cooled down.
3. Open the pump door.
4. Place a container close to the pump to
collect any spillage.
5. Release the emergency emptying hose,
place it in the container and remove its
cap cover.
6. When no more water comes out, un-
screw the pump and remove it. Always
electrolux 15
keep a rag nearby to dry up spillage of
water when removing the pump.
7. Remove any objects from the pump im-
peller by rotating it.
8. Refit the cap on the emergency empty-
ing hose and place the latter back in its
seat.
9. Screw the pump fully in.
10. Close the pump door.
Warning!
When the appliance is in use and depending
on the programme selected there can be hot
water in the pump. Never remove the pump
cover during a wash cycle, always wait until
the appliance has finished the cycle, and is
empty. When replacing the cover, ensure it
is securely retightened so as to stop leaks
and young children being able to remove it.
Cleaning the water inlet filter
If you notice that the machine is taking longer
to fill, check that the filter in the water inlet
hose is not blocked.
1. Turn off the water tap.
2. Unscrew the hose from the tap.
3. Clean the filter in the hose with a stiff
brush.
4. Screw the hose back onto the tap.
Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the machine:
1. pull out the plug from the power socket;
2. close the water tap;
3. if necessary, wait until the water has
cooled down;
4. open the pump door;
5. place a bowl on the floor and place the
end of the emergency emptying hose into
the bowl. Remove its cap. The water
should drain by gravity into the bowl.
When the bowl is full, put the cap back
on the hose. Empty the bowl. Repeat the
procedure until water stops flowing out;
6. clean the pump if necessary as previously
described;
7. replace the emergency emptying hose in
its seat after having plugged it;
8. screw the pump again and close the
door.
Frost precautions
If the machine is installed in a place where the
temperature could drop below 0°C, proceed
as follows:
16 electrolux
1. close the water tap and unscrew the wa-
ter inlet hose from the tap;
2. place the end of the emergency emptying
hose and that of the inlet hose in a bowl
placed on the floor and let water drain
out;
3. screw the water inlet hose back on and
reposition the emergency emptying hose
after having put the cap on again.
By doing this, any water remaining in the ma-
chine is removed, avoiding ice forming and
consequently damage to the appliance.
When you use the machine again, make sure
that the ambient temperature is above 0°C.
Important! Every time you drain the water
through the emergency emptying hose you
must pour 2 litres of water into the main wash
compartment of the detergent drawer and
then run the drain programme. This will
activate the ECO Valve device avoiding that
part of the detergent remains unused at next
washing.
What to do if…
Certain problems are due to lack of simple
maintenance or oversights, which can be
solved easily without calling out an engineer.
Before contacting your local Service Centre,
please carry out the checks listed below.
During machine operation it is possible that
the red pilot light of button 6 blinks to indi-
cate that the machine is not working.
Once the problem has been eliminated,
press the button 6 to restart the programme.
If after all checks, the problem persists, con-
tact your local Service Centre.
Problem Possible cause/Solution
The washing machine does
not start:
The door has not been closed (the button 6 red light blinks).
•Close the door firmly.
The plug is not properly inserted in the power socket.
Insert the plug into the power socket.
There is no power at the socket.
Please check your domestic electrical installation.
The main fuse has blown.
Replace the fuse.
The programme selector dial is not correctly positioned and the but-
ton 6 has not been pressed.
Please turn the selector dial and press the button 6 again.
The delay start has been selected.
If the laundry are to be washed immediately, cancel the delay start.
The machine does not fill:
The water tap is closed (the button 6 red light blinks).
•Open the water tap.
The inlet hose is squashed or kinked (the button 6 red light blinks).
Check the inlet hose connection.
The filter in the inlet hose is blocked (the button 6 red light blinks).
Clean the water inlet hose filter.
The door is not properly closed (the button 6 red light blinks).
•Close the door firmly.
The machine fills then emp-
ties immediately:
The end of the drain hose is too low.
Refer to relevant paragraph in «water drainage» section.
electrolux 17
Problem Possible cause/Solution
The machine does not emp-
ty and/or does not spin:
The drain hose is squashed or kinked (the button 6 red light blinks).
Check the drain hose connection.
The drain filter is clogged (the button 6 red light blinks).
Clean the drain filter.
An option or a programme that ends with the water still in the tub or
a that eliminates all the spinning phases has been selected.
Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
Redistribute the laundry.
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much
foam) has been used.
Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings.
It is not always easy to see this as the water runs down the hose;
check to see if it is damp.
Check the water inlet hose connection.
The drain or inlet hose is damaged.
Replace it with a new one.
The cap on the emergency emptying hose has not been replaced
or the filter has not been properly screwed in after cleaning action.
Refit the cap on the emergency emptying hose or screw the filter
fully in.
Unsatisfactory washing re-
sults:
Too little detergent or unsuitable detergent has been used.
Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
Check if you have selected the correct temperature.
Excessive laundry load.
Reduce the laundry load.
The door will not open:
The programme is still running.
Wait the end of washing cycle.
The door lock has not been released.
Wait until the light 8.2 has gone out.
There is water in the drum.
Select drain or spin programme to empty out the water.
The machine vibrates is
noisy:
The transit bolts and packing have not been removed.
Check the correct installation of the appliance.
The support feet have not been adjusted
Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
Redistribute the laundry.
Maybe there is very little laundry in the drum.
Load more laundry.
Spinning starts late or the
machine does not spin:
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is redis-
tributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can re-
sume. If, after 10 minutes, the laundry is still not evenly distributed
in the drum, the machine will not spin. In this case, redistribute the
load manually and select the spin programme.
Redistribute the laundry.
The load is too small.
Add more items, redistribute the load manually and then select
the spinning programme.
18 electrolux
Problem Possible cause/Solution
The machine makes an un-
usual noise:
The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor en-
sures a softer start and more even distribution of the laundry in the
drum when spinning, as well as increased stability of the machine.
No water is visible in the
drum:
Machines based on modern technology operate very economically
using very little water without affecting performance.
If you are unable to identify or solve the prob-
lem, contact our service centre. Before tele-
phoning, make a note of the model, serial
number and purchase date of your machine:
the Service Centre will require this informa-
tion.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
M
o
d
.
.
.
. .
..
..
.
P
r
o
d
.
N
o
.
.
.
.
...
..
S
e
r.
N
o
.
.
..
...
..
.
Technical data
Dimensions Width
Height
Depth
60 cm
85 cm
63 cm
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate,
on the inner edge of the appliance door.
Water supply pressure Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load Cotton 8 kg
Spin Speed Maximum 1000 rpm
Consumption values
Programme Energy consumption
(KWh)
Water consumption
(litres)
Programme duration
(Minutes)
Algodón 90° 2.7 66 165
Algodón 60° 1.6 63 140
Algodón + ECONÓMI-
CO option 60°
1)
1.36 59 160
Algodón 40° 0.95 63 140
Sintéticos 40° 0.6 58 90
electrolux 19
Programme Energy consumption
(KWh)
Water consumption
(litres)
Programme duration
(Minutes)
Delicados 40° 0.7 70 70
Lana / A mano 30 0.4 65 55
1) «This programme at 60°C with a load of 8 kg is the reference programme for the data entered in the
energy label, in compliance with EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely indicative, as it
may vary depending on the quantity and type of laundry, on the inlet water temperature
and on the ambient temperature.
Installation
Unpacking
All transit bolts and packing must be re-
moved before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging, carefully
lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable and the
draining and inlet hose from the hose
holders on the rear of the appliance.
3. Unscrew the three bolts.
4. Slide out the relevant plastic spacers.
20 electrolux
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Electrolux EWF10190W User manual

Category
Washing machines
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI