H3C LSW1XGT2P0 User manual
- Category
- Network switches
- Type
- User manual
This manual is also suitable for
H3C LSW1XGT2P0 & LSW1XGT4P0
Interface Cards
User Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 5PW100-20130116
Copyright © 2013, Hangzhou H3C Technologies Co., Ltd. and
its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or
by any means without prior written consent of Hangzhou H3C
Technologies Co., Ltd.
Trademarks
H3C, , H3CS, H3CIE, H3CNE, Aolynk, ,
H3Care, , IRF, NetPilot, Netflow, SecEngine, SecPath,
SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks
of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the
property of their respective owners
Notice
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to
ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any
kind, express or implied.
Environmental protection
This product has been designed to comply with the environmental
protection requirements. The storage, use, and disposal of this product
must meet the applicable national laws and regulations.
Obtaining documentation
You can access the most up-to-date H3C product documentation on the
World Wide Web at http://www.h3c.com
.
Click the links on the top navigation bar to obtain different categories of
product documentation:
[Technical Support & Documents > Technical Documents]
– Provides
hardware installation, software upgrading, and software feature
configuration and maintenance documentation.
[Products & Solutions]
– Provides information about products and
technologies, as well as solutions.
[Technical Support & Documents > Software Download]
– Provides the
documentation released with the software version.
Technical support
service@h3c.com
http://www.h3c.com
Documentation feedback
You can e-mail your comments about product documentation to
We appreciate your comments.
i
Contents
Interface cards ·························································································· 1
Introduction to interface cards ··························································· 1
Front panel ·························································································· 1
1/10GBase-T autosensing Ethernet port description ······················ 2
LED description ··················································································· 3
Installing and removing an interface card ············································· 5
Installing an interface card ································································ 5
Removing an interface card ······························································ 8
Verifying the installation ······································································· 10
1
Interface cards
Introduction to interface cards
This manual introduces the following 10-Gigabit interface cards:
• LSW1XGT4P0—Provides four 1/10GBase-T autosensing Ethernet
ports.
• LSW1XGT2P0—Provides two 1/10GBase-T autosensing Ethernet
ports.
NOTE:
The interface cards described in this document are applicable to
multiple models of H3C switches, and the switch models that it
applies to may update with time. For the latest information, consult
H3C marketing staff or technical support.
Front panel
Figure 1 LSW1XGT4P0 front panel
(1) 1/10GBase-T
autosensing Ethernet port
(2) 1/10GBase-T autosensing
Ethernet port LED
2
Figure 2 LSW1XGT2P0 front panel
(1) 1/10GBase-T
autosensing Ethernet port
(2) 1/10GBase-T autosensing
Ethernet port LED
1/10GBase-T autosensing Ethernet port
description
Table 1 1/10GBase-T autosensing Ethernet port specifications
Item Specification
Connector type RJ-45
Port standard
• 10 Gbps, full duplex
• 1 Gbps, full duplex
• MDI/MDI-X, auto-sensing
3
Item Specification
Max transmission
distance
• Category-6 unshielded twisted pair cable:
55 m (180.45 ft)
• Category-6 shielded twisted pair cable:
100 m (328.08 ft)
• Category-6A or higher twisted pair cable:
100 m (328.08 ft)
Transmission
medium
Category-6 or higher twisted pair cable
Compliance
standard
IEEE 802.3an and 802.3ab
LED description
Every LSW1XGT4P0 and LSW1XGT2P0 interface card provides a port
status LED for each port on the panel. It indicates the operating status of
a port together with the port mode LED on the switch.
Table 2 LED description
Port mode
LED on the
switch
Port status LED
on the interface
card
Description
Steady
green (rate
mode)
Steady green
The port is operating at a rate of
10 Gbps. The LED is fast flashing
when data is being sent and/or
received on the port.
4
Port mode
LED on the
switch
Port status LED
on the interface
card
Description
Steady yellow
The port is operating at a rate of 1
Gbps only. The LED is fast flashing
when data is being sent and/or
received on the port.
Flashing yellow
(3 Hz)
Power-on self test (POST) has
failed on the port.
Off No link is present on the port.
Steady
yellow
(duplex
mode)
Steady green
The port is operating in full-duplex
mode only. The LED is fast
flashing when data is being sent
and/or received on the port.
Flashing yellow
(3 Hz)
POST has failed on the port.
Off No link is present on the port.
NOTE:
Port status LED of the interface card is affected by the port mode
switching button on your switch. For more information about the
port mode switching button, see the installation guide of the switch.
5
Installing and removing an interface
card
This section takes the LSW1XGT4P0 interface card and the H3C
S5820X-28C switch to illustrate the installation and removal procedures.
The methods for installing and removing the LSW1XGT2P0 are similar.
The following tools are needed for installation and removal:
• Phillips screwdriver
• ESD-preventive wrist strap
NOTE:
The installation tools are not shipped together with H3C's Ethernet
switches. Prepare them yourself.
When you install or remove an interface card, follow these guidelines:
• Avoid touching the surface-mounted components directly with your
hands.
• Avoid using excessive force in the operation.
• If you remove an interface card and do not install a new one, install a
filler panel as soon as possible to prevent dust and ensure the normal
ventilation in the switch.
Installing an interface card
1. Put on an ESD-preventive wrist strap and make sure the strap is in
good contact with your skin and is properly grounded.
6
2. Use a Phillips screwdriver to loosen the mounting screws of the
filler panel on the expansion slot of the switch's front panel and
remove the filler panel, as shown in Figure 3.
Keep the
removed filler panel properly for future use.
Figure 3 Removing a filler panel
(1) Phillips screwdriver (2) Switch's front panel
(3) Filler panels
3. Unpack the interface card.
7
Figure 4 Interface card appearance
(1) Captive screw (2) Ejector lever
4. Gently push the interface card in along the guide rails until the
interface card is in close contact with the switch. (See callout 1
in Figure 5.) Th
en push the ejector levers at both sides inward.
(See callout 2 in Figure 5.)
5. Fasten the
captive screws with a Phillips screwdriver to secure the
interface card. (See callout 3 in Figure 5.)
8
Figure 5 Installing an interface card
NOTE:
W
hen tightening the captive screws at both sides of the interface
card with a screwdriver or an electric screwdriver, make sure the
torque is not bigger than 0.4 N-m.
Removing an interface card
1. Put on an ESD-preventive wrist strap and make sure the strap is in
good contact with your skin and is properly grounded.
2. Use a Phillips screwdriver to loosen the captive screws at both
sides of the interface card until all spring pressure is released. (See
callout 1 in Figure 6.)
3. Hold the ejector l
evers at both sides of the interface card and push
them outward. (See callout 2 in Figure 6.) P
ull the interface card
along the guide rails until it completely comes out of the switch
chassis. (See callout 3 in Figure 6.)
1
2
3
3
2
9
Figure 6 Removing an interface card
3
1
2
1
2
10
Verifying the installation
When the switch operates properly, verify that the interface card is
operating properly according to the port status LED.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
H3C LSW1XGT2P0 User manual
- Category
- Network switches
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
H3C s5820x series Installation guide
-
H3C S5800-56C-PWR Installation guide
-
-
-
-
-
-
-
-