WARRIOR Item 57174 Owner's manual

Brand: WARRIOR

Model: Item 57174

Category: Power universal cutters

Type: Owner's manual

!"#"$%&'(%)*+#"$*%,$-%.$$/-00)))1.,(+&(2(*"3.$14&5

65,"7%&'(%$*4.8"4,7%#'//&($%,$-%/(&9'4$#'//&($:.,(+&(2(*"3.$14&5

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the

back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference. 20e

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

2020 by Harbor Freight Tools

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly an d se rv ic e may n ot b e in cl uded.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Page 2 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 57174

EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ

G,+7*%&2%O&8$*8$#

Safety ........................................................................2

Specifications ............................................................7

Setup .........................................................................8

Operation ..................................................................11

Maintenance .............................................................15

Parts List and Diagram .............................................18

Warranty ...................................................................20

QFKMLMR%EHNSITE%FMU%U6;LMLGLIME

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that

follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

LNJIKGFMG%EF;6GH%LM;IKNFGLIM

R*8*(,7%J&)*(%G&&7%E,2*$V%Q,(8"83#

K*,9%,77%#,2*$V%),(8"83#=%"8#$('4$"&8#=%"77'#$(,$"&8#%,89%#/*4"2"4,$"&8#%/(&W"9*9%)"$.%$."#%/&)*(%$&&71%

Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

E,W*%,77%),(8"83#%,89%"8#$('4$"&8#%2&(%2'$'(*%(*2*(*84*1

The term “power tool” in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

1. Q&(X%,(*,%#,2*$V

a. Y**/%)&(X%,(*,%47*,8%,89%)*77%7"$1%

Cluttered or dark areas invite accidents.

b. U&%8&$%&/*(,$*%/&)*(%$&&7#%"8%*Z/7&#"W*%

,$5&#/.*(*#=%#'4.%,#%"8%$.*%/(*#*84*%&2%

27,55,+7*%7"<'"9#=%3,#*#%&(%9'#$1%Power tools

create sparks which may ignite the dust or fumes.

c. Y**/%4."79(*8%,89%+V#$,89*(#%,),V%

)."7*%&/*(,$"83%,%/&)*(%$&&71%Distractions

can cause you to lose control.

2. 67*4$("4,7%#,2*$V

a. J&)*(%$&&7%/7'3#%5'#$%5,$4.%$.*%&'$7*$1%

M*W*(%5&9"2V%$.*%/7'3%"8%,8V%),V1%U&%8&$%'#*%

,8V%,9,/$*(%/7'3#%)"$.%*,($.*9%[3(&'89*9\%

/&)*(%$&&7#1%Unmodified plugs and matching

outlets will reduce risk of electric shock.

Page 3;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 57174

EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ

b. FW&"9%+&9V%4&8$,4$%)"$.%*,($.*9%&(%

3(&'89*9%#'(2,4*#=%#'4.%,#%/"/*#=%

(,9",$&(#=%(,83*#%,89%(*2("3*(,$&(#1%

There is an increased risk of electric shock

if your body is earthed or grounded.

c. U&%8&$%*Z/&#*%/&)*(%$&&7#%$&%(,"8%&(%)*$%

4&89"$"&8#1%Water entering a power tool

will increase the risk of electric shock.

d. U&%8&$%,+'#*%$.*%4&(91%M*W*(%'#*%$.*%4&(9%

2&(%4,((V"83=%/'77"83%&(%'8/7'33"83%$.*%/&)*(%

$&&71%Y**/%4&(9%,),V%2(&5%.*,$=%&"7=%#.,(/%

*93*#%&(%5&W"83%/,($#1%Damaged or entangled

cords increase the risk of electric shock.

e. Q.*8%&/*(,$"83%,%/&)*(%$&&7%&'$9&&(#=%

'#*%,8%*Z$*8#"&8%4&(9%#'"$,+7*%2&(%&'$9&&(%

'#*1%Use of a cord suitable for outdoor

use reduces the risk of electric shock.

f. L2%&/*(,$"83%,%/&)*(%$&&7%"8%,%9,5/%7&4,$"&8%

"#%'8,W&"9,+7*=%'#*%,%3(&'89%2,'7$%4"(4'"$%

"8$*(('/$*(%[R;OL\%/(&$*4$*9%#'//7V1%Use of

a GFCI reduces the risk of electric shock.

3. J*(#&8,7%#,2*$V

a. E$,V%,7*($=%),$4.%).,$%V&'%,(*%9&"83%,89%

'#*%4&55&8%#*8#*%).*8%&/*(,$"83%,%

/&)*(%$&&71%U&%8&$%'#*%,%/&)*(%$&&7%)."7*%

V&'%,(*%$"(*9%&(%'89*(%$.*%"827'*84*%&2%

9('3#=%,74&.&7%&(%5*9"4,$"&81%%A moment

of inattention while operating power tools

may result in serious personal injury.

b. P#*%/*(#&8,7%/(&$*4$"W*%*<'"/5*8$1%F7),V#%

)*,(%*V*%/(&$*4$"&81%%Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

c. J(*W*8$%'8"8$*8$"&8,7%#$,($"831%68#'(*%$.*%

#)"$4.%"#%"8%$.*%&22?/&#"$"&8%+*2&(*%4&88*4$"83%

$&%/&)*(%#&'(4*%,890&(%+,$$*(V%/,4X=%/"4X"83%

'/%&(%4,((V"83%$.*%$&&71%Carrying power tools

with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d. K*5&W*%,8V%,9]'#$"83%X*V%&(%)(*84.%

+*2&(*%$'(8"83%$.*%/&)*(%$&&7%&81%%A wrench

or a key left attached to a rotating part of the

power tool may result in personal injury.

e. U&%8&$%&W*((*,4.1%Y**/%/(&/*(%2&&$"83%,89%

+,7,84*%,$%,77%$"5*#1 This enables better control

of the power tool in unexpected situations.

f. U(*##%/(&/*(7V1%U&%8&$%)*,(%7&&#*%47&$."83%

&(%]*)*7(V1%Y**/%V&'(%.,"(=%47&$."83%

,89%37&W*#%,),V%2(&5%5&W"83%/,($#1%%

Loose clothes, jewelry or long hair

can be caught in moving parts.

g. L2%9*W"4*#%,(*%/(&W"9*9%2&(%$.*%4&88*4$"&8%

&2%9'#$%*Z$(,4$"&8%,89%4&77*4$"&8%

2,4"7"$"*#=%*8#'(*%$.*#*%,(*%4&88*4$*9%

,89%/(&/*(7V%'#*91%%Use of dust collection

can reduce dust-related hazards.

h. U&%8&$%7*$%2,5"7",("$V%3,"8*9%2(&5%2(*<'*8$%

'#*%&2%$&&7#%,77&)%V&'%$&%+*4&5*%

4&5/7,4*8$%,89%"38&(*%$&&7%#,2*$V%

/("84"/7*#1%%A careless action can cause

severe injury within a fraction of a second.

i. Only use safety equipment that has been

approved by an appropriate standards agency.

Unapproved safety equipment may not provide

adequate protection. Eye protection must be

ANSI-approved and breathing protection

must be NIOSH-approved for the

specific hazards in the work area.

j. Avoid unintentional starting.

Prepare to begin work before turning on the tool.

k. Do not leave the tool unattended when

it is plugged into an electrical outlet.

Turn off the tool, and unplug it from its

electrical outlet before leaving.

l. This product is not a toy.

Keep it out of reach of children.

m. People with pacemakers should consult their

physician(s) before use. Electromagnetic fields

in close proximity to heart pacemaker could

cause pacemaker interference or pacemaker

failure. In addition, people with pacemakers

should:

• Avoid operating alone.

• Do not use with Trigger locked on.

• Properly maintain and inspect to avoid

electrical shock.

• Properly ground power cord.

Ground Fault Circuit Interrupter (GFCI)

should also be implemented – it prevents

sustained electrical shock.

n. The warnings, precautions, and instructions

discussed in this instruction manual cannot

cover all possible conditions and situations

that may occur. It must be understood by the

operator that common sense and caution are

factors which cannot be built into this product,

but must be supplied by the operator.

4. J&)*(%$&&7%'#*%,89%4,(*

a. U&%8&$%2&(4*%$.*%/&)*(%$&&71%P#*%$.*%4&((*4$%

/&)*(%$&&7%2&(%V&'(%,//7"4,$"&81%%The correct

power tool will do the job better and safer

at the rate for which it was designed.

b. U&%8&$%'#*%$.*%/&)*(%$&&7%"2%$.*%#)"$4.%

9&*#%8&$%$'(8%"$%&8%,89%&221%%Any power

tool that cannot be controlled with the switch

is dangerous and must be repaired.

c. U"#4&88*4$%$.*%/7'3%2(&5%$.*%/&)*(%

#&'(4*%,890&(%(*5&W*%$.*%+,$$*(V%/,4X=%

"2%9*$,4.,+7*=%2(&5%$.*%/&)*(%$&&7%+*2&(*%

5,X"83%,8V%,9]'#$5*8$#=%4.,83"83%

,44*##&("*#=%&(%#$&("83%/&)*(%$&&7#1%%

Such preventive safety measures reduce the

risk of starting the power tool accidentally.

Page 4 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 57174

EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ

d. E$&(*%"97*%/&)*(%$&&7#%&'$%&2%$.*%(*,4.%&2%

4."79(*8%,89%9&%8&$%,77&)%/*(#&8#%'82,5"7",(%

)"$.%$.*%/&)*(%$&&7%&(%$.*#*%"8#$('4$"&8#%

$&%&/*(,$*%$.*%/&)*(%$&&71%%Power tools are

dangerous in the hands of untrained users.

e. N,"8$,"8%/&)*(%$&&7#%,89%,44*##&("*#1%

O.*4X%2&(%5"#,7"385*8$%&(%+"89"83%&2%5&W"83%

/,($#=%+(*,X,3*%&2%/,($#%,89%,8V%&$.*(%

4&89"$"&8%$.,$%5,V%,22*4$%$.*%/&)*(%$&&7^#%

&/*(,$"&81%L2%9,5,3*9=%.,W*%$.*%/&)*(%$&&7%

(*/,"(*9%+*2&(*%'#*1%%Many accidents are

caused by poorly maintained power tools.

f. Y**/%4'$$"83%$&&7#%#.,(/%,89%47*,81%%Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g. P#*%$.*%/&)*(%$&&7=%,44*##&("*#%,89%$&&7%+"$#%

*$41%"8%,44&(9,84*%)"$.%$.*#*%"8#$('4$"&8#=%

$,X"83%"8$&%,44&'8$%$.*%)&(X"83%4&89"$"&8#%

,89%$.*%)&(X%$&%+*%/*(2&(5*91%%Use of the

power tool for operations different from those

intended could result in a hazardous situation.

h. Y**/%.,897*#%,89%3(,#/"83%#'(2,4*#%

9(V=%47*,8%,89%2(**%2(&5%&"7%,89%3(*,#*1%%

Slippery handles and grasping surfaces

do not allow for safe handling and control

of the tool in unexpected situations.

5. E*(W"4*

a. _,W*%V&'(%/&)*(%$&&7%#*(W"4*9%+V%,%

<',7"2"*9%(*/,"(%/*(#&8%'#"83%&87V%"9*8$"4,7%

(*/7,4*5*8$%/,($#1%%This will ensure that

the safety of the power tool is maintained.

b. Maintain labels and nameplates on the tool.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

6. E,2*$V%"8#$('4$"&8#%2&(%5"$(*%#,)#

a. N"$(*%#,)#%,(*%"8$*89*9%$&%4'$%)&&9%&(%

)&&9?7"X*%/(&9'4$#=%$.*V%4,88&$%+*%'#*9%

)"$.%,+(,#"W*%4'$?&22%).**7#%2&(%4'$$"83%

2*((&'#%5,$*(",7%#'4.%,#%+,(#=%(&9#=%#$'9#=%

*$41%Abrasive dust causes moving parts

such as the lower guard to jam. Sparks from

abrasive cutting will burn the lower guard,

the kerf insert and other plastic parts.

b. P#*%47,5/#%$&%#'//&($%$.*%)&(X/"*4*%

).*8*W*(%/&##"+7*1%L2%#'//&($"83%$.*%

)&(X/"*4*%+V%.,89=%V&'%5'#$%,7),V#%X**/%

V&'(%.,89%,$%7*,#$%>``%55%2(&5%*"$.*(%#"9*%

&2%$.*%#,)%+7,9*1%U&%8&$%'#*%$."#%#,)%$&%

4'$%/"*4*#%$.,$%,(*%$&&%#5,77%$&%+*%#*4'(*7V%

47,5/*9%&(%.*79%+V%.,891 If your hand is

placed too close to the saw blade, there is an

increased risk of injury from blade contact.

c. G.*%)&(X/"*4*%5'#$%+*%#$,$"&8,(V%,89%

47,5/*9%&(%.*79%,3,"8#$%+&$.%$.*%2*84*%

,89%$.*%$,+7*1%U&%8&$%2**9%$.*%)&(X/"*4*%

into the blade or cut ″freehand″ in any way.

Unrestrained or moving workpieces could

be thrown at high speeds, causing injury.

d. J'#.%$.*%#,)%$.(&'3.%$.*%)&(X/"*4*1%U&%

8&$%/'77%$.*%#,)%$.(&'3.%$.*%)&(X/"*4*1%G&%

5,X*%,%4'$=%(,"#*%$.*%#,)%.*,9%,89%/'77%"$%&'$%

&W*(%$.*%)&(X/"*4*%)"$.&'$%4'$$"83=%#$,($%$.*%

5&$&(=%/(*##%$.*%#,)%.*,9%9&)8%,89%/'#.%

$.*%#,)%$.(&'3.%$.*%)&(X/"*4*1 Cutting on

the pull stroke is likely to cause the saw blade

to climb on top of the workpiece and violently

throw the blade assembly towards the operator.

e. M*W*(%4(&##%V&'(%.,89%&W*(%$.*%"8$*89*9%

7"8*%&2%4'$$"83%*"$.*(%"8%2(&8$%&(%+*."89%

$.*%#,)%+7,9*1%Supporting the workpiece

″cross handed″ i.e. holding the workpiece

to the right of the saw blade with your left

hand or vice versa is very dangerous.

f. U&%8&$%(*,4.%+*."89%$.*%2*84*%)"$.%*"$.*(%

.,89%47&#*(%$.,8%>``%55%2(&5%*"$.*(%

#"9*%&2%$.*%#,)%+7,9*=%$&%(*5&W*%)&&9%

#4(,/#=%&(%2&(%,8V%&$.*(%(*,#&8%)."7*%

$.*%+7,9*%"#%#/"88"831%The proximity of the

spinning saw blade to your hand may not be

obvious and you may be seriously injured.

g. L8#/*4$%V&'(%)&(X/"*4*%+*2&(*%4'$$"831%L2%$.*%

)&(X/"*4*%"#%+&)*9%&(%),(/*9=%47,5/%"$%)"$.%

$.*%&'$#"9*%+&)*9%2,4*%$&),(9%$.*%2*84*1%

F7),V#%5,X*%4*($,"8%$.,$%$.*(*%"#%8&%3,/%

+*$)**8%$.*%)&(X/"*4*=%2*84*%,89%$,+7*%,7&83%

$.*%7"8*%&2%$.*%4'$1%Bent or warped workpieces

can twist or shift and may cause binding on the

spinning saw blade while cutting. There should

be no nails or foreign objects in the workpiece.

h. U&%8&$%'#*%$.*%#,)%'8$"7%$.*%$,+7*%"#%47*,(%

&2%,77%$&&7#=%)&&9%#4(,/#=%*$41=%*Z4*/$%2&(%

$.*%)&(X/"*4*1%Small debris or loose pieces

of wood or other objects that contact the

revolving blade can be thrown with high speed.

i. O'$%&87V%&8*%)&(X/"*4*%,$%,%$"5*1%

Stacked multiple workpieces cannot be

adequately clamped or braced and may

bind on the blade or shift during cutting.

j. 68#'(*%$.*%5"$(*%#,)%"#%5&'8$*9%&(%/7,4*9%

&8%,%7*W*7=%2"(5%)&(X%#'(2,4*%+*2&(*%'#*1%

A level and firm work surface reduces the

risk of the mitre saw becoming unstable.

k. J7,8%V&'(%)&(X1%6W*(V%$"5*%V&'%4.,83*%$.*%

+*W*7%&(%5"$(*%,837*%#*$$"83=%5,X*%#'(*%$.*%

,9]'#$,+7*%2*84*%"#%#*$%4&((*4$7V%$&%#'//&($%

$.*%)&(X/"*4*%,89%)"77%8&$%"8$*(2*(*%)"$.%

$.*%+7,9*%&(%$.*%3',(9"83%#V#$*51%Without

turning the tool ″ON″ and with no workpiece

on the table, move the saw blade through a

complete simulated cut to assure there will be

no interference or danger of cutting the fence.

Page 5;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 57174

EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ

l. J(&W"9*%,9*<',$*%#'//&($%#'4.%,#%$,+7*%

*Z$*8#"&8#=%#,)%.&(#*#=%*$41%2&(%,%)&(X/"*4*%

$.,$%"#%)"9*(%&(%7&83*(%$.,8%$.*%$,+7*%$&/1%

Workpieces longer or wider than the mitre saw

table can tip if not securely supported. If the

cut-off piece or workpiece tips, it can lift the

lower guard or be thrown by the spinning blade.

m. U&%8&$%'#*%,8&$.*(%/*(#&8%,#%,%#'+#$"$'$*%

2&(%,%$,+7*%*Z$*8#"&8%&(%,#%,99"$"&8,7%

#'//&($1%Unstable support for the workpiece

can cause the blade to bind or the workpiece

to shift during the cutting operation pulling

you and the helper into the spinning blade.

n. G.*%4'$?&22%/"*4*%5'#$%8&$%+*%],55*9%&(%

/(*##*9%+V%,8V%5*,8#%,3,"8#$%$.*%#/"88"83%

#,)%+7,9*1%If confined, i.e. using length

stops, the cut-off piece could get wedged

against them blade and thrown violently.

o. F7),V#%'#*%,%47,5/%&(%,%2"Z$'(*%9*#"38*9%

$&%/(&/*(7V%#'//&($%(&'89%5,$*(",7%#'4.%,#%

(&9#%&(%$'+"831%Rods have a tendency to roll

while being cut, causing the blade to ″bite″ and

pull the work with your hand into the blade.

p. T*$%$.*%+7,9*%(*,4.%2'77%#/**9%+*2&(*%

4&8$,4$"83%$.*%)&(X/"*4*1%This will reduce

the risk of the workpiece being thrown.

q. L2%$.*%)&(X/"*4*%&(%+7,9*%+*4&5*#%],55*9=%

$'(8%$.*%5"$(*%#,)%&221%Q,"$%2&(%,77%5&W"83%

/,($#%$&%#$&/%,89%9"#4&88*4$%$.*%/7'3%

2(&5%$.*%/&)*(%#&'(4*%,890&(%(*5&W*%

$.*%+,$$*(V%/,4X1%G.*8%)&(X%$&%2(**%$.*%

],55*9%5,$*(",71%Continued sawing with

a jammed workpiece could cause loss of

control or damage to the .mitre saw.

r. F2$*(%2"8"#."83%$.*%4'$=%(*7*,#*%$.*%#)"$4.=%

.&79%$.*%#,)%.*,9%9&)8%,89%),"$%2&(%

$.*%+7,9*%$&%#$&/%+*2&(*%(*5&W"83%$.*%

4'$?&22%/"*4*1%Reaching with your hand

near the coasting blade is dangerous.

s. _&79%$.*%.,897*%2"(57V%).*8%5,X"83%,8%

"84&5/7*$*%4'$%&(%).*8%(*7*,#"83%$.*%#)"$4.%

+*2&(*%$.*%#,)%.*,9%"#%4&5/7*$*7V%"8%$.*%

9&)8%/&#"$"&81%The braking action of the

saw may cause the saw head to be suddenly

pulled downward, causing a risk of injury.

7. !"+(,$"&8%E,2*$V

This tool vibrates during use.

Repeated or long-term exposure to vibration may

cause temporary or permanent physical injury,

particularly to the hands, arms and shoulders.

To reduce the risk of vibration-related injury:

a. Anyone using vibrating tools regularly or for

an extended period should first be examined

by a doctor and then have regular medical

check-ups to ensure medical problems are not

being caused or worsened from use. Pregnant

women or people who have impaired blood

circulation to the hand, past hand injuries,

nervous system disorders, diabetes, or

Raynaud’s Disease should not use this tool.

If you feel any symptoms related to

vibration (such as tingling, numbness,

and white or blue fingers), seek medical

advice as soon as possible.

b. Do not smoke during use. Nicotine reduces

the blood supply to the hands and fingers,

increasing the risk of vibration-related injury.

c. Wear suitable gloves to reduce the

vibration effects on the user.

d. Use tools with the lowest vibration

when there is a choice.

e. Include vibration-free periods each day of work.

f. Grip tool as lightly as possible (while still keeping

safe control of it). Let the tool do the work.

g. To reduce vibration, maintain the tool as

explained in this manual. If any abnormal

vibration occurs, stop use immediately.

Page 6 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 57174

EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ

R(&'89"83

GI%JK6!6MG%6T6OGKLO%E_IOY%FMU%U6FG_%;KIN%

LMOIKK6OG%RKIPMULMR%QLK6%OIMM6OGLIM-%

O.*4X%)"$.%,%<',7"2"*9%*7*4$("4",8%"2%V&'%,(*%"8%9&'+$%,#%$&%).*$.*(%$.*%&'$7*$%"#%/(&/*(7V%

3(&'89*91%%U&%8&$%5&9"2V%$.*%/&)*(%4&(9%/7'3%/(&W"9*9%)"$.%$.*%$&&71%%M*W*(%(*5&W*%$.*%

3(&'89"83%/(&83%2(&5%$.*%/7'31%%U&%8&$%'#*%$.*%$&&7%"2%$.*%/&)*(%4&(9%&(%/7'3%"#%9,5,3*91%%L2%9,5,3*9=%.,W*%

"$%(*/,"(*9%+V%,%#*(W"4*%2,4"7"$V%+*2&(*%'#*1%%L2%$.*%/7'3%)"77%8&$%2"$%$.*%&'$7*$=%.,W*%,%/(&/*(%&'$7*$%"8#$,77*9%+V%

,%<',7"2"*9%*7*4$("4",81

R(&'89*9%G&&7#-%G&&7#%)"$.%G.(**%J(&83%J7'3#

a?J(&83%J7'3%,89%I'$7*$

1. Tools marked with “Grounding Required” have

a three wire cord and three prong grounding

plug. The plug must be connected to a properly

grounded outlet. If the tool should electrically

malfunction or break down, grounding provides

a low resistance path to carry electricity away

from the user, reducing the risk of electric shock.

[E**%a?J(&83%J7'3%,89%I'$7*$1\

2. The grounding prong in the plug is connected

through the green wire inside the cord to the

grounding system in the tool. The green wire

in the cord must be the only wire connected to

the tool’s grounding system and must never

be attached to an electrically “live” terminal.

[E**%a?J(&83%J7'3%,89%I'$7*$1\

3. The tool must be plugged into an appropriate outlet,

properly installed and grounded in accordance

with all codes and ordinances. The plug and outlet

should look like those in the preceding illustration.

[E**%a?J(&83%J7'3%,89%I'$7*$1\

U&'+7*%L8#'7,$*9%G&&7#-%G&&7#%)"$.%G)&%J(&83%J7'3#

I'$7*$#%2&(%b?J(&83%J7'3

1. Tools marked “Double Insulated” do not

require grounding. They have a special

double insulation system which satisfies

OSHA requirements and complies with

the applicable standards of Underwriters

Laboratories, Inc., the Canadian Standard

Association, and the National Electrical Code.

2. Double insulated tools may be used in either of the

120 volt outlets shown in the preceding illustration.%%%

[E**%I'$7*$#%2&(%b?J(&83%J7'31\

6Z$*8#"&8%O&(9#

1. Grounded tools require a three wire extension cord.

Double Insulated tools can use either

a two or three wire extension cord.

2. As the distance from the supply outlet increases,

you must use a heavier gauge extension cord.

Using extension cords with inadequately sized wire

causes a serious drop in voltage, resulting in loss of

power and possible tool damage. [E**%G,+7*%F1\

3. The smaller the gauge number of the wire, the

greater the capacity of the cord. For example,

a 14 gauge cord can carry a higher current

than a 16 gauge cord. [E**%G,+7*%F1\

4. When using more than one extension cord

to make up the total length, make sure

each cord contains at least the minimum

wire size required. [E**%G,+7*%F1\

Page 7;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 57174

EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ

5. If you are using one extension cord for more

than one tool, add the nameplate%amperes

and use the sum to determine the required

minimum cord size. [E**%G,+7*%F1\

6. If you are using an extension cord outdoors, make

sure it is marked with the suffix “W-A” (“W” in

Canada) to indicate it is acceptable for outdoor use.

7. Make sure the extension cord is properly wired

and in good electrical condition. Always replace

a damaged extension cord or have it repaired

by a qualified electrician before using it.

8. Protect the extension cords from sharp objects,

excessive heat, and damp or wet areas.

GFST6%F-%%K6OINN6MU6U%NLMLNPN%QLK6%

RFPR6%;IK%6cG6MELIM%OIKUEd%[>b`0be`%!ITG\

MFN6JTFG6

FNJ6K6E

[,$%2'77%7&,9\

6cG6MELIM%OIKU%

T6MRG_

bBf B`f CBf >``f >B`f

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

d%S,#*9%&8%7"5"$"83%$.*%7"8*%W&7$,3*%9(&/%$&%2"W*%W&7$#%,$%

>B`g%&2%$.*%(,$*9%,5/*(*#1

EV5+&7&3V

Double Insulated

Volts

Alternating Current

Amperes

xxxx/min.

No Load Revolutions per Minute (RPM)

WARNING marking concerning Risk

of Eye Injury. Wear ANSI-approved

safety goggles with side shields.

Read the manual before

set-up and/or use.

WARNING marking

concerning Risk of Fire.

Do not cover ventilation ducts.

Keep flammable objects away.

WARNING marking concerning

Risk of Electric Shock.

Properly connect power cord

to appropriate outlet.

E/*4"2"4,$"&8#

Electrical Rating 120 VAC / 60 Hz / 9.5 A

Rated No Load Speed 5200 RPM

Cutting Capacity at 0° 2" x 4-5/16"

Cutting Capacity at 45° 2" x 3-1/8"

Maximum Bevel 45° Left

Maximum Miter 47° Left and Right

Saw Blade

7-1/4" Diameter

5/8" Round Arbor

5200 Minimum RPM Rating

Page 8 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 57174

EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ

E*$'/%?%S*2&(*%P#*-

%K*,9%$.*%6MGLK6%LNJIKGFMG%EF;6GH%LM;IKNFGLIM%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%

5,8',7%"847'9"83%,77%$*Z$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1

M&$*- For additional information regarding the parts listed in the

following pages, refer to Parts List and Diagram on page 18.

N&'8$"83

1. Use the four bolt holes provided in the Base

to mount the Miter Saw to a stable support

before use. Mounting hardware not included.

2. Ensure that the miter saw is always stable

and secure (e.g. fixed to a bench).

F##*5+7V

1. Squeeze the Spring Clip on the Dust Bag to open

the mouth of the Bag. Slip the Bag over the

Dust Outlet at the rear of the Saw Head Assembly

and release the Clip to secure the Bag to the Outlet.

2. If adjustable and/or removable workpiece

support extension(s) are provided, always fix

and use these extension(s) during operation.

;'84$"&8#

S*W*7%F837*%

L89"4,$&(

;*84*

E7"9"83%

;*84*

G("33*(%

T&4X

G("33*(

_,897*

O7,5/

N"$*(%E4,7*

S,#*

Y*(2%S&,(9

N"$*(%F837*%

L89"4,$&(

Page 9;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 57174

EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ

S*W*7%

T&4X%

T*W*(

_*,9%

T&4X9&)8%

J"8

U'#$%S,3

U'#$%I'$7*$

S7,9*

S7,9*%R',(9

G,+7*

;*84*%

T&4X%

Y8&+

G,+7*%

T&4X%

Y8&+

U*#4("/$"&8%&2%E*7*4$*9%;'84$"&8#

S7,9*%R',(9%&/*(,$"&8-%

When the cutting head is lowered, the Blade Guard

raises automatically. When the cutting head is raised the

Blade Guard returns to its safety position. Keep hands

clear of the Blade when the Handle is lowered. Do not

interfere with the proper movement of the Blade Guard.

M&$*- Additional functions are explained

elsewhere in the manual.

Page 10 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 57174

EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ

Q&(X%F(*,

1. Designate a work area that is clean and well lit.

The work area must not allow access by children

or pets to prevent distraction and injury.

2. There must not be objects, such as utility lines,

nearby that will present a hazard while working.

3. Route the power cord along a safe route to reach

the work area without creating a tripping hazard or

exposing the power cord to possible damage. The

power cord must reach the work area with enough

extra length to allow free movement while working.

E,)%S7,9*%E*7*4$"&8

1. Any saw blade that will be used must be

marked as suitable for the material to be cut.

2. Use only a saw blade diameter in

accordance with the markings on the saw.

See specification table for the bore diameter

and the maximum kerf of the saw blade.

3. Use only saw blades that are marked with a speed

equal or higher than the speed marked on the tool.

R',(9%E*$'/

Check that the Lower Blade Guard is in place,

moves freely, and closes instantly.

U'#$%6Z$(,4$"&8%E*$'/

To use the Dust Collection Bag, slide the Bag

over the Dust Outlet at the rear of the Saw Head

Assembly. Refer to Assembly on page 8.

Page 11;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 57174

EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ

I/*(,$"83%L8#$('4$"&8#

%K*,9%$.*%6MGLK6%LNJIKGFMG%EF;6GH%LM;IKNFGLIM%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%

5,8',7%"847'9"83%,77%$*Z$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1

G&&7%O.,83"83

M&$*- Replacement blade sold separately.

1. Unplug the tool from its power source.

2. Raise the Lower Blade Guard out

of the way and hold it up.

3. Loosen the Guard Plate Bolt until it

disengages the Guard Plate.

4. Swing the Guard Plate up and out of the way.

T&)*(%S7,9*%

R',(9

R',(9%R',(9%

J7,$*J7,$*

F(+&(%F(+&(%

S&7$S&7$

I'$*(%I'$*(%

;7,83*;7,83*

_*Z%_*Z%

Y*VY*V

;7,83*%;7,83*%

Q(*84.%Q(*84.%

R',(9%R',(9%

J7,$*%S&7$J7,$*%S&7$

;"3'(*%F

5. Insert the two prongs of the supplied Flange Wrench

into the two holes in the Outer Flange. Hold the

Outer Flange in place and use the supplied Hex Key

to loosen the Arbor Bolt by turning OTIOYQLE6.

LNJIKGFMG-%G.*%F(+&(%S&7$%.,#%,%7*2$?.,89*9%

$.(*,9%,89%(*5&W*#%+V%$'(8"83%OTIOYQLE61

6. Remove the Arbor Bolt and

Outer Flange. Refer to Figure B.

M&$*- Make sure the Inner Flange

stays in place on the Spindle.

I'$*(%

;7,83*

L88*(%

;7,83*

E/"897*

S7,9*

F(+&(%

S&7$

;"3'(*%S

7. Remove the used blade. Install the new Blade.

Make sure that the Blade′s rotation arrow

/&"8$#%"8%$.*%#,5*%9"(*4$"&8%,#%$.*%(&$,$"&8%

,((&)%&8%$.*%P//*(%S7,9*%R',(91

8. Replace the Outer Flange and Arbor Bolt.

Position the cupped side of the Flange against

the Blade. Hold the Outer Flange with the Flange

Wrench and tighten the Arbor Bolt with the Hex

Key by turning it OIPMG6KOTIOYQLE6.

9. Rotate the Guard Plate back into place and

secure it with the Guard Plate Bolt.

10. Move the Lower Blade Guard back into place.

11. QFKMLMRi%%GI%JK6!6MG%E6KLIPE%

LMjPKH-%%N,X*%#'(*%$.*%T&)*(%S7,9*%R',(9%

&/*(,$*#%#5&&$.7V%,89%/(&/*(7V%/(&$*4$#%

2(&5%$.*%S7,9*%+*2&(*%'#"83%$.*%E,)1

Page 12 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 57174

EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ

E*$$"83%,89%G*#$"83

GI%JK6!6MG%E6KLIPE%LMjPKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%

N,X*%#'(*%$.,$%$.*%G("33*(%"#%"8%$.*%&22?/&#"$"&8%,89%'8/7'3%$.*%$&&7%2(&5%"$#%

*7*4$("4,7%&'$7*$%+*2&(*%/*(2&(5"83%,8V%/(&4*9'(*%"8%$."#%#*4$"&81

F9]'#$"83%$.*%N"$*(%F837*

A miter cut is one that is at an angle across the horizontal surface of the material. 45º miter cuts to join two

pieces in a right angle corner are common. A 30º cut is often used for a scarf joint or to make a chamfered end.

1. Loosen the Table Lock Knob by

turning it counterclockwise.

2. Lower the Saw Head Assembly and lock it

down with the Head Lockdown Pin. Using the

Handle, move the Table to the desired angle.

3. The Miter Angle Indicator will indicate the

selected angle. The Miter Scale displays

often used miter angles, including 15º, 22.5º,

30º, and 45º on both left and right sides.

4. Tighten the Table Lock Knob after adjusting

the miter angle. Release the Head Lockdown

Pin and raise the Saw Head Assembly.

5. With the Table adjusted to the desired angle,

place the workpiece flush against the Fence,

secure it with the Clamp and make the cut.

F9]'#$"83%$.*%S*W*7%F837*

A bevel cut is one that is at an angle vertically. Bevel cuts can be used to cut a miter in relatively wide

and thin material. Bevel cuts can be used in combination with a miter cut to form a compound angle.

Compound angle cuts are often used in crown moldings, picture frames and similar trim materials.

1. Loosen the Bevel Lock Knob

at the rear of the saw.

2. Move the Saw Head Assembly to the desired angle.

Read the angle on the Bevel Angle Indicator.

3. Lock the Saw Head Assembly into position

by rotating the Bevel Lock Knob clockwise.

Tighten firmly but do not over-tighten.

4. Make a sample cut in a piece of scrap to

confirm that the bevel angle is correct.

If it is not, correct the angle before cutting.

S*W*7%T&4X%

Y8&+

S*W*7%

F837*%

L89"4,$&(

;"3'(*%O

F7"38"83%$.*%;*84*

1. After adjusting the miter or bevel setting, check and

adjust the Sliding Fence.

2. Loosen the Fence Lock Knob, and move the

Sliding Fence to be within 1/8" of the blade.

3. Tighten the Fence Lock Knob. Make sure that the

Sliding Fence still does not contact the Blade.

;*84*%T&4X%

Y8&+

E7"9"83%E7"9"83%

;*84*;*84*

;"3'(*%U%

Page 13;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 57174

EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ

Kerf Board Replacement / Adjustment

If the Kerf Board becomes damaged it must be replaced.

1. Remove the four screws holding

the Kerf Board in place.

2. Install a new Kerf Board. Replace the

four screws and tighten them slightly.

G&%,9]'#$%$.*%Y*(2%S&,(9-

1. Lower the blade assembly and lock it

down with the Head Lockdown Pin.

2. Adjust the Kerf Board so the right side of the

Blade slightly clears the edge of the Kerf Board.

3. Check for blade clearance by moving the Saw

Head through its full range of motion with the bevel

angle set at 0 º and at maximum left bevel angle.

Refer to Adjusting the Bevel Angle on page 12.

4. If the Saw Blade hits the Kerf Board, loosen

the four screws and adjust. Tighten the screws

and check again for blade clearance.

5. After verifying blade clearance, tighten the four

screws holding the Kerf Board in place.

Q&(X/"*4*%,89%Q&(X%F(*,%E*$%P/

1. Secure loose workpieces using a vise or clamps

(not included) to prevent movement while working.

2. Cut only the following materials:

Dimensional lumber, plywood, particle board, plastic.

M&$*- Use caution to avoid overheating the cutting tips.

If cutting plastic, cut at an even pace to avoid melting it.

3. Refer to cutting capacities in the Specifications Table

on page 7 for limitations on workpiece size.

4. Allow room on both left and right sides

of saw for extended workpieces.

5. Use additional supports if needed to ensure

the stability of the workpiece. Mount the Saw

so that the surface is level to the ground, and

additional supports to provide a surface on the

same level as the saw table. If the work surface

and any workpiece supports are not level, and

on the same level, unwanted bevel angles will

appear in the cuts resulting in poor joinery.

6. Secure workpieces to the saw table using the Clamp

or other clamping devices (not included). Securing

the workpiece will provide safety by preventing kick

back and by removing the need to hold workpieces

near the blade by hand. Clamping the workpiece

will also improve cutting accuracy by preventing the

workpiece from moving during the cutting operation.

Q&(X/"*4*%E'//&($

1. Support the workpiece to be level with the table,

and so that after the cut is made the cut off pieces

will not fall. Use sawhorses or other supports

(not included) to support longer workpieces.

2. If the workpiece is not level, you will make

an unintentional bevel cut in the material.

If the workpiece is not supported, it will bind

the blade and may cause the material to

kick back, potentially causing injury.

Page 14 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 57174

EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ

R*8*(,7%L8#$('4$"&8#%2&(%P#*

1. Make sure that the Trigger is in the

off-position, then plug in the tool.

N"$*(%E,)%O'$$"83%J(&4*9'(*

2. Unlock the Head Lock-Down Pin.

3. Check that all adjustment knobs are tight (Table

Lock Knob, Bevel Lock Knob, Fence Lock Knob).

4. Blow any sawdust or debris away from the Fence.

Place the work material against the Fence.

5. Align the marked location of the cut on the

work material with the Saw Blade.

M&$*- To prevent your workpiece from being

cut too short, align the edge of the blade

with the measured mark, keeping the rest of

the blade on the waste side of the cut.

6. Hold the work material in place using the Clamp.

Ensure that the work material is level and supported

securely. Use saw horses or supports if necessary.

UFMR6Ki%E,)#%4,8%<'"4X7V%

,5/'$,$*%2"83*(#%"2%5"#'#*91%%%

Y**/%.,89#%)*77%47*,(%&2%4'$$"83%,(*,1

7. Grip the Saw Handle, press the Trigger

Lock with your thumb, and squeeze

the Trigger to start the Saw.

8. Use two hands and hold workpiece securely

against table and fence at all times.

9. Press down lightly to cut the workpiece.

Press straight down, “chopping” the material.

Do not bear down on the material — use

light downward pressure. If the material

binds the blade, release the Trigger.

10. When the cut is completed, raise the Saw

Head, release the Trigger, wait for the Blade

to stop turning, release the Clamp and

remove the workpiece from the Saw.

11. To prevent accidents, turn off the tool and

unplug it after use. Clean, then store the

tool indoors out of children’s reach.

12. Lock the Saw Head down and lock all other

adjustments before moving the Saw. Use the

handle cut outs on each side of the Base to

lift and support the Saw while moving it.

Page 15;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 57174

EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ

N,"8$*8,84*%,89%E*(W"4"83%L8#$('4$"&8#

%J(&4*9'(*#%8&$%#/*4"2"4,77V%*Z/7,"8*9%"8%$."#%5,8',7%5'#$%

+*%/*(2&(5*9%&87V%+V%,%<',7"2"*9%$*4.8"4",81

GI%JK6!6MG%E6KLIPE%LMjPKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%

N,X*%#'(*%$.,$%$.*%G("33*(%"#%"8%$.*%&22?/&#"$"&8%,89%'8/7'3%$.*%$&&7%2(&5%"$#%

*7*4$("4,7%&'$7*$%+*2&(*%/*(2&(5"83%,8V%/(&4*9'(*%"8%$."#%#*4$"&81

GI%JK6!6MG%E6KLIPE%LMjPKH%;KIN%GIIT%;FLTPK6-%

U&%8&$%'#*%9,5,3*9%*<'"/5*8$1%%L2%,+8&(5,7%8&"#*%&(%W"+(,$"&8%

&44'(#=%.,W*%$.*%/(&+7*5%4&((*4$*9%+*2&(*%2'($.*(%'#*1

O7*,8"83=%N,"8$*8,84*=%,89%T'+("4,$"&8

1. S6;IK6%6FO_%PE6= inspect the general

condition of the tool. Check for:

• loose hardware

• misalignment or binding of moving parts

• damaged cord/electrical wiring

• cracked or broken parts

• any other condition that may

affect its safe operation.

2. F;G6K%PE6= wipe external surfaces of the tool with

clean cloth. Carefully clean the dust collection chute

and the area around the Lower Blade Guard. Check

that the Lower Blade Guard moves smoothly through

its entire range of movement, without sticking.

3. Periodically, wear ANSI-approved

safety goggles and NIOSH-approved

breathing protection and blow dust out of

the motor vents using dry compressed air.

4. %QFKMLMRi%GI%JK6!6MG%E6KLIPE%

LMjPKH-%%L2%$.*%/7'3%&(%$.*%#'//7V%4&(9%&2%$."#%

/&)*(%$&&7%"#%9,5,3*9=%"$%5'#$%+*%(*/7,4*9%

&87V%+V%,%<',7"2"*9%#*(W"4*%$*4.8"4",81

O.*4X"83%,89%O,7"+(,$"83%$.*%;*84*

The Fence holds the workpiece in a fixed position

while the Table and/or the blade assembly

are adjusted in a miter or bevel angle.

To make accurate cuts, the Fence must be

perpendicular (at a 90º angle) to the Saw Blade.

1. Before beginning work, make a test cut on

scrap material with the Table set at 0º.

2. Check the cut with an accurate square.

You can also reverse the two pieces, hold

the cut ends together, and hold a good

straight edge along the side of the pieces.

3. If either test reveals that the cut is not a true 90º

angle, adjust the Fence before beginning work.

L2%;*84*%8**9#%,9]'#$5*8$-

1. First unplug the tool.

2. Lower the blade assembly and lock it in

place using the Head Lockdown Pin.

3. Lay a carpenter’s square on the Table with one

edge along the Blade and the other along the

Fence. Any inaccuracy should be visible.

MIG6- The square must contact the surface of the

Blade, not the teeth, for an accurate reading.

4. The Fence is held in place with bolts at each

end. Loosen the bolts slightly, and gently tap the

Fence into position using a soft mallet. Retighten

the bolts and make another test cut. Repeat the

process until the Fence is adjusted accurately.

5. Once the Fence is accurately adjusted,

tighten the bolts firmly in place. Recheck

one last time, then proceed to work.

Page 16 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 57174

EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ

O,7"+(,$"83%$.*%N"$*(%F837*%L89"4,$&(

After checking or adjusting the Fence to

confirm that it is at 90º to the Blade, check

the accuracy of the Miter Angle Indicator.

1. Loosen the screw holding the

Angle Indicator in place.

2. Rotate it until the pointer is exactly on 90º.

3. Retighten the screw.

O,7"+(,$"83%$.*%S*W*7%F837*

For making accurate cuts, the Saw Blade must

be adjusted to be exactly vertical to the Table.

1. To check the angle, have the blade assembly

in its normal upright position. Make a cut on a

piece of flat sided, fairly thick scrap material.

2. Check the cut with an accurate square.

The cut should be at exactly 90º.

3. Angle can also be checked by rotating one cut-off

piece 180º and holding the cut ends together.

If the cut is not exactly vertical, the two

pieces will form a slight angle.

4. If necessary, the bevel angle can be corrected

by adjusting the adjustment screw on the

right side near the Bevel Lock Knob.

5. Once the bevel angle is adjusted, adjust the Bevel

Angle Indicator to read 0º when the Saw Blade is

in the vertical position. Loosen the screw holding

the Indicator in place, adjust it to be exactly

over the 0º mark, then retighten the screw.

G(&'+7*#.&&$"83

J(&+7*5 J&##"+7*%O,'#*# T"X*7V%E&7'$"&8#

Tool will not start. 1. Cord not connected.

2. No power at outlet.

3. Tool’s thermal reset breaker

tripped (if equipped).

4. Internal damage or wear.

(Carbon brushes or

Trigger, for example.)

1. Check that cord is plugged in.

2. Check power at outlet. If outlet is unpowered,

turn off tool and check circuit breaker.

If breaker is tripped, make sure circuit is right

capacity for tool and circuit has no other loads.

3. Turn off tool and allow to cool.

Press reset button on tool.

4. Have technician service tool.

Tool operates slowly. 1. Forcing tool to work too fast.

2. Extension cord too long or cord

diameter too small.

1. Allow tool to work at its own rate.

2. Eliminate use of extension cord. If an extension

cord is needed, use one with the proper diameter

for its length and load. See Extension Cords

in Grounding section on page 6.

Performance

decreases over time.

Carbon brushes worn

or damaged.

Have qualified technician replace brushes.

Excessive noise

or rattling.

Internal damage or wear. (Carbon

brushes or bearings, for example.)

Have technician service tool.

Overheating. 1. Forcing tool to work too fast.

2. Blocked motor housing vents.

3. Motor being strained by long or

small diameter extension cord.

1. Allow tool to work at its own rate.

2. Wear ANSI-approved safety goggles and

NIOSH-approved dust mask/respirator while

blowing dust out of motor using compressed air.

3. Eliminate use of extension cord. If an extension

cord is needed, use one with the proper diameter

for its length and load. See Extension Cords

in Grounding section on page 6.

% ;&77&)%,77%#,2*$V%/(*4,'$"&8#%).*8*W*(%9",38&#"83%&(%#*(W"4"83%$.*%$&&71%%%

U"#4&88*4$%/&)*(%#'//7V%+*2&(*%#*(W"4*1

Page 17;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 57174

EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ

JT6FE6%K6FU%G_6%;ITTIQLMR%OFK6;PTTH

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

K*4&(9%J(&9'4$^#%E*(",7%M'5+*(%_*(*-%

M&$*-%L2%/(&9'4$%.,#%8&%#*(",7%8'5+*(=%(*4&(9%5&8$.%,89%V*,(%&2%/'(4.,#*%"8#$*,91

M&$*- Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Page 18 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 57174

EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ

J,($#%T"#$%,89%U",3(,5

J,($#%T"#$

J,($ U*#4("/$"&8

1 Washer

2 Shield Roller

3 Connecting Rod Screw

4 Connecting Rod

5 Nut M5

6 Lower Blade Guard

7 Plum Screw

8 Shield Coil Spring

9 Guard Plate

10 M5 x 12 Screw

11 M5 x 10 Screw

12 Power Cord

13 Power Cord Sheath

14 St4.2 x 14 Screw

15 M5 x 40 Screw

16 Upper Handle

17 Trigger

18 Self-Locking Spring

19 Microswitch Spring

20 Trigger Lock

21 Microswitch

24 Power Cord Clamp

25 Lower Handle

26 Roller Bearing Hk081210

27 Large Gear

28 Elastic Retainer Type A 32

29 Bearing 6002

30 Front Cover

31 Spindle

32 M5 x 16 Screw Set

33 Inner Flange

34 Blade

35 Outer Flange

36 Arbor Bolt

37 Cross Pin

38 Torsion Spring

39 Dusting Collection

40 Upper Blade Guard

41 Windshield

42 Bearing 609

43 Rotor Assembly

44 Bolt 4.2 x 50

45 Stator Assembly

46 Motor Housing

47 Carbon Brush Cover

48 Carbon Brush

J,($ U*#4("/$"&8

49 Carbon Brush Holder

50 M5 x 45 Bolt Set

51 Clamp Knob Assembly

52 Clamp Rod

53 Knob

54 Clamp Bracket

55 Clamping Plate

56 Split Washer 5

57 Fence

58 Disc Lock Friction Pad

59 M6 x 25 Screw Set

60 M6 x 12 Screw

61 Fence Knob

62 Sllding Fence

63 Steel Ball 8

64 Spring

65 M10 x 20 Screw

66 Base

67 Rubber Foot

68 M8 x 30 Screw

69 M6 x 16 Screw

70 Friction Pad

71 Table

72 Miter Angle Indicator

73 M4 x 10 Screw Set

74 Kerf Board

75 M4 x 8 Screw

76 Nut M8

77 Washer 8 x 22 x 2

78 Bevel Scale

79 Shaft

80 Bevel Angle Indicator

81 M6 x 10 Screw

82 Pivot

83 Washer 10

84 Nut M10

85 Bevel Lock Knob

86 Screw

87 Nut M6

88 O-Ring Φ5 x Ø1.8

89 M6 x 35 Screw

90 Pin

91 M6 x 25 Bolt

92 Dust Bag

93 Hex Key

94 Flange Wrench

Page 19;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 57174

EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ

F##*5+7V%U",3(,5

bABe>%F3&'(,%K&,9%%k%%O,7,+,#,#=%OF%D>a`b%%k%%>?@@@?@AA?BCDC

T"5"$*9%D`%U,V%Q,((,8$V

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

WARRIOR Item 57174 Owner's manual

Brand: WARRIOR

Model: Item 57174

Category: Power universal cutters

Type: Owner's manual

Download PDF

report

WARRIOR Item 57174 Owner's manual

WARRIOR Item 57174 Owner's manual

Related papers

Other documents