Lenoxx TT600 is a versatile audio system that combines a turntable, cassette player, radio, and digital encoder. It allows you to play and encode vinyl records, cassette tapes, and external audio sources onto USB drives or SD cards. The system features a 33/45/78 RPM belt-driven turntable with auto-stop and a slot-in cassette player. It also has an AUX input for connecting external devices, such as CD players or MP3 players. Additionally, the TT600 includes a built-in AM/FM radio with digital readout and a headphone jack for private listening.
Lenoxx TT600 is a versatile audio system that combines a turntable, cassette player, radio, and digital encoder. It allows you to play and encode vinyl records, cassette tapes, and external audio sources onto USB drives or SD cards. The system features a 33/45/78 RPM belt-driven turntable with auto-stop and a slot-in cassette player. It also has an AUX input for connecting external devices, such as CD players or MP3 players. Additionally, the TT600 includes a built-in AM/FM radio with digital readout and a headphone jack for private listening.
1
TT-600
TURNTABLE WITH CASSETTE PLAYER, RADIO, AUX IN AND
USB/SD ENCODING
INSTRUCTION MANUAL
READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USE
2
PRODUCT FEATURES
- 33/45/78 RPM SELECTABLE TURNTABLE
- AUTOMATIC / MANUAL STOP TURNTABLE
- BELT DRIVEN SYSTEM
- SLOT-IN CASSETTE PLAYER
- DIRECT USB/SD ENCODING FOR TURNTABLE, CASSETTE & AUX IN
- AUX IN FOR CONNECTION OF OTHER DEVICE (EG. CD & MP3 PLAYER)
- USB/SD SLOT FOR MP3 PLAYBACK
- COPYING FILE FROM USB TO SD
- DELETING FILE IN USB AND SD
- DIGITAL READ-OUT ANALOGUE AM/FM RADIO
- 45RPM ADAPTOR INCLUDED
- LCD DISPLAY WITH BLUE BACKLIGHT
- RCA LINE-OUT
- BUILT-IN SPEAKER WITH 2 x 1.5W OUTPUT
LOCATION OF CONTROL
1) DUST COVER
2) MODE (USB/SD)
3) RECORD
BUTTON
4) AM/FM/FM STEREO SELECTOR
5) FUNCTIONS SELECTOR
6) AUX IN JACK
7) DELETE BUTTON
8) 3.5 MM HEADPHONE JACK
9) PROG BUTTON
10) USB SOCKET
11) LCD DISPLAY
12) POWER LED INDICATOR
13) PLAY/PAUSE
BUTTON
14) STOP
BUTTON
15) VOLUME KNOB
16) TUNING KNOB
17) SKIP UP
BUTTON
18) SKIP DOWN
BUTTON
19) SD/MMC CARD SOLT
20) RIGHT SPEAKER
21) 45RPM ADAPTOR
22) LIFT LEVER (FOR RECORD PLAY / PUASE)
23) AUTO STOP ON/OFF SWITCH
24) 33/45/78 RPM SPEED SELECTOR
25) TONE ARM
26) CASSETTE PLAYER
27) LINE OUT SOCKET
28) FM WIRE ANTENNA
29) AC POWER CORD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
3
CAUTION:
USAGE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULTE IN HAZARDOUS RADIATION EXPOSURE.
THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE
PERSONNEL.
PRECAUTIONS FOR USE
INSTALLATION
UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL.
DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAINS VOLTAGE AND BEFORE
ALL OTHER CONNECTIONS HAVE BEEN MADE.
DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL CENTIMETERS
AROUND THE UNIT FOR VENTILATION.
CONNECTION
1. CONNECT THE POWER CORD (29) TO AC OUTLET
2. SWITCH THE FUNCTION SELECTOR (5). IF THE BACKLIGHT ON THE LCD DISPLAY LIGHTS UP, IT MEANS
THE POWER SUPPLY IS NORMAL, NOW YOUR SYSTEM IS READY FOR USE.
LISTENING TO RADIO
RADIO TUNING
1. TURN FUNCTION SELECTOR (5) TO SELECT “TUNER” MODE.
2. SELECT THE DESIRED BAND BY RADIO BAND SELECTOR (4) (AM, FM OR FM-STEREO).
3. TUNE TO THE REQUIRED STATION BY TUNING AND HOLDING THE TUNING KNOB (16) LEFT OR RIGHT
FOR 1-2 SECOND, AND THEN RELEASE.
4. THE UNIT WILL START SEEKING AUTOMATICALLY AND STOP WHEN A RADIO STATION IS FOUND.
5. REPEAT STEP 3 & 4 UNTIL THE REQUIRED STATION IS FOUND.
6. ADJUST VOLUME KNOB (18) TO THE DESIRED VOLUME LEVEL..
7. AM : THERE IS A BUILT-IN AM BAR ANTENNA. IF AM RECECPTION IS WEAK, SLIGHTLY ROTATING OR
RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION.
8. FM : THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA HANGING AT THE REAR CABINET. THIS WIRE
SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION.
FM & FM-STEREO RECEPTION
SET THE RADIO BAND SELECTOR (4) AT “ FM ” POSITION. PROGRAMS ARE RECEIVED IN MONO MODE.
IN PARTICULAR WHEN STEREO SIGNAL ARE WEAK. IT IS PREFERABLE TO RECEIVE THE PROGRAM IN
MONO.
SET THE RADIO BAND SELECTOR (4) AT “FM-ST” POSITION FOR RECEIVING STEREO PROGRAMS. THE
“ST” ICON WILL LIGHT UP ON THE DISPLAY TO SHOW FM STEREO PROGRAM IS RECEIVING.
PHONO & ENCODING
NOTED:
- REMOVE THE STYLUS PROTECTOR.
- BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM
REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.
1. SELECT TO “ PHONO ” FUNCTION FROM FUNCTION SELECTOR (5)
2. SET THE SPEED SELECTOR TO THE PROPER POSITION DEPENDING ON THE RECORD TO BE PLAYED.
3. PLACE THE RECORD ON THE PLATTER (USE THE 45 RPM ADAPTOR IF REQUIRED).
4. PUSH THE LIFT LEVER (22) UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK,
AND THEN SLOWLY MOVE IT TO THE RECORD SIDE. THE PLATTER WILL START TO
ROTATE.
5. PUT DOWN THE LIFT LEVER (22) TO DROP THE TONE ARM AND TOUCH THE RECORD
GENTLY. PHONO PLAYING STARTS NOW.
6. PUSH THE LIFT LEVER (22) UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK,
NOW PLATTER WILL STILL BE ROTATING BUT PHONO PLAYING WILL STOP. TO CONTINUE THE PLAYING,
THE USER NEEDS TO PUT DOWN THE LIFT LEVER (22).
7. ADJUST THE VOLUME TO THE DESIRED LEVEL.
4
8. AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING. PUSH THE LIFT LEVER
(22) UPWARD TO RAISE THE TONE ARM AND MOVE IT TO THE ARM PARK, AND THEN PUT DOWN THE
LIFT LEVER (22).
9. TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE ARM PARK.
REMARK : AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT SETTING, SO IT WILL
STOP BEFORE THE LAST TRACK FINISHES. IN THIS CASE, SELECT THE AUTO-STOP SWITCH (23) TO “ OFF
“ POSITION, THEN IT WILL RUN TO THE END OF THE RECORD BUT WILL NOT STOP AUTOMATICALLY (TURN
OFF THE UNIT BY POWER BUTTON OR SWITCH BACK THE AUTO-STOP SWITCH (28) TO “ ON “ POSITION TO
STOP THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE ARM PARK.
PHONO ENCODING
1.SET THE FUNCTION BUTTON TO “PHONO” MODE AND THEN INSERT MEMORY DEVICE (USB DRIVE, SD OR
MMC CARD)
2.PRESS THE “REC” BUTTON (3), IT WILL TAKE 3-4 SECOND TO READ MEMORY DEVICE. THEN USB OR SD
ICON WILL BE FLASHING.
3.PRESS SKIP UP BUTTON (17) OR SKIP DOWN BUTTON (18) TO SELECT DESIRED MODE
(USB OR SD) FOR ENCODING. THEN PRESS THE “REC” BUTTON (3) AGAIN TO CONFIRM. AND THE
SYSTEM IS STARTING THE ENCODING MODE AFTER FEW SECONDS.
4.THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY DURNIG ENCODING.
5.TO FINISH ENCODING, PRESS STOP BUTTON (14) AND DISPLAY WILL SHOW “END” AND RETURN TO
“ PHONO” MODE.
6.IF ONLY USB DRIVE OR SD/MMC CARD IS INSERTED, STEP 3 CAN BE SKIPPED.
REMARK:-
- THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLYING TIME OF THE PHONO
- THE RECORDING FORMAT IS PRESET AT – MP3
BIT RATE : 128 KBPS
CASSETTE TAPE & ENCODING
1. SELECT TO “ TAPE/AUX ” FUNCTION FROM FUNCTION SELECTOR (5).
2. AFTER INSERTING THE CASSETTE TAPE, THE SYSTEM WILL START PLAYING AUTOMATICALLY.
3. ADJUST THE VOLUME TO THE DESIRED LEVEL.
4. PRESS THE “TAPE FAST FORWARD / EJECT” BUTTON HALF WAY DURING PLAYING, THE TAPE WILL BE
ADVANCED FORWARD RAPIDLY.
5. SLIGHTLY PRESS THE “TAPE FAST FORWARD / EJECT “ BUTTON AGAIN TO RESUME NORMAL PLAYING,
THE BUTTON WILL RESUME TO THE OUTERMOST POSITION.
6. PRESS THE “TAPE FAST FORWARD / EJECT” BUTTON COMPLETELY, THEN THE PLAYING WILL BE
STOPPED AND THE CASSETTE TAPE WILL BE EJECTED.
5
REMARK : MAKE SURE THE DIRECTION IS CORRECT WHEN INSERTING
THE TAPE. TO AVOID DAMAGING THE TAPE, IT IS HIGHLY RECOMMENDED
TO TAKE OUT THE TAPE AFTER LISTENING.
CASSETTE TAPE ENCODING
1.SET THE FUNCTION BUTTON TO “TAPE/AUX” MODE AND THEN INSERT MEMORY DEVICE (USB DRIVE, SD
OR MMC CARD)
2.PRESS THE “REC” BUTTON (3), IT WILL TAKE 3-4 SECOND TO READ MEMORY DEVICE. THEN USB OR SD
ICON WILL BE FLASHING.
3.PRESS SKIP UP BUTTON (17) OR SKIP DOWN BUTTON (18) TO SELECT DESIRED MODE
(USB OR SD) FOR ENCODING. THEN PRESS THE “REC” BUTTON (3) AGAIN TO CONFIRM. AND THE
SYSTEM IS STARTING THE ENCODING MODE AFTER FEW SECONDS.
4.THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY DURNIG ENCODING.
5.TO FINISH ENCODING, PRESS STOP BUTTON (14) AND DISPLAY WILL SHOW “END” AND RETURN TO
“TAPE/AUX” MODE.
6.IF ONLY USB DRIVE OR SD/MMC CARD IS INSERTED, STEP 3 CAN BE SKIPPED.
REMARK:-
- THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLYING TIME OF THE TAPE.
- THE RECORDING FORMAT IS PRESET AT – MP3
BIT RATE : 128 KBPS
AUX IN JACK & ENCODING
1. SELECT TO “TAPE / AUX” FUNCTION FROM FUNCTION SELECTOR (5), THEN CONNECT THE EXTERNAL
AUDIO DEVICE (SUCH AS CD PLAYER) THROUGH THE “AUX IN JACK” (6). AUDIO SIGNAL FROM THE
EXTERNAL AUDIO DEVICE CAN BE PLAYED THROUGH THE SYSTEM.
2. PLAYING OF AUX IN IS PRIOR TO CASSETTE TAPE IF “AUX IN JACK” (6) IS CONNECTED WITH OTHER
EXTERNAL AUDIO DEVICE.
AUX IN ENCODING
1.SET THE FUNCTION BUTTON TO “TAPE/AUX” MODE AND THEN INSERT MEMORY DEVICE (USB DRIVE, SD
OR MMC CARD)
2.PRESS THE “REC” BUTTON (3), IT WILL TAKE 3-4 SECOND TO READ MEMORY DEVICE. THEN USB OR SD
ICON WILL BE FLASHING.
3.PRESS
SKIP UP BUTTON (17) OR SKIP DOWN BUTTON (18) TO SELECT DESIRED MODE
(USB OR SD) FOR ENCODING. THEN PRESS THE “REC” BUTTON (3) AGAIN TO CONFIRM.
AND THE
SYSTEM IS STARTING THE ENCODING MODE AFTER FEW SECONDS.
4.THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY DURNIG ENCODING.
5.TO FINISH ENCODING, PRESS STOP BUTTON (14) AND DISPLAY WILL SHOW “END” AND RETURN TO
“TAPE/AUX” MODE.
6.IF ONLY USB DRIVE OR SD/MMC CARD IS INSERTED, STEP 3 CAN BE SKIPPED.
REMARK:-
- THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLYING TIME OF THE TAPE.
- THE RECORDING FORMAT IS PRESET AT – MP3 BIT RATE : 128 KBPS
6
HEADPHONE JACK & LINE OUT SOCKET
- THIS SYSTEM CAN BE CONNECTED WITH HEADPHONE OR EXTERNAL AMPLIFIER /
SPEAKER BY 3.5MM HEADPHONE JACK (8).
- THIS SYSTEM CAN BE CONNECTED WITH EXTERNAL DEVICE (EG. AMPLIFIER AND
SPEAKER) BY LINE OUT SOCKET (27) AT REAR CABINET.
PLAYBACK OF MP3/WMA SONG VIA USB STORAGE MEDIA OR MEMORY CARD
CONNECTING
THE SYSTEM IS ABLE TO DECODE AND PLAYBACK ALL MP3 / WMA FILE WHICH STORED IN THE MEMORY
MEDIA WITH USB CONNECTING PORT OR SD/MMC MEMORY CARD.
1. PLUG-IN THE USB PLUG WITH THE FACE UP & MAKE SURE IT GOING INTO COMPLETELY OR INSERT
THE MEMORY CARD IN THE DIRECTION OF THE ARROW AS SHOWN IN THE LABEL ON THE UNDERSIDE
OF THE MEMORY CARD SLOT COVER. INSERT STRAIGHT WITHOUT BENDING.
2. CONNECTING THE USB UPSIDE DOWN OR BACKWARDS COULD DAMAGE THE AUDIO SYSTEM OR THE
STORAGE MEDIA (USB THUMB DRIVE / SD/MMC CARD). CHECK TO BE SURE THE DIRECTION IS
CORRECT BEFORE CONNECTION.
3. SET FUNCTION SELECTOR (5) AT USB/SD MODE AND THEN PRESS MODE BUTTON (2) TO SELECT “USB
OR CARD” MODE.
4. THE SYSTEM WILL START READING THE STORAGE MEDIA AUTOMATICALLY AFTER MODE SELECTION,
AND DISPLAY WILL SHOW THE TOTAL NUMBER OF FOLDER (EG. F08) AND MP3/WMA FILES (EG. 016).
5. THEN THE SYSTEM WILL START AUDIO PLAYBACK FROM DESRIED DEVICE (USB OR SD/MMC)
AUTOMATICALLY.
PLAY / PAUSE BUTTON
- PRESS THE “PLAY/PAUSE” BUTTON (13) ONCE TO HALT PLAYING, PRESS IT AGAIN TO
CONTINUE.
STOP BUTTON
-
PRESS THE “STOP” BUTTON (14) TO END UP AUDIO PLAYBACK, THEN DISPLAY WILL SHOW
THE TOTAL NUMBER OF MP3/WMA FILES. AND THEN USER CAN PRESS “SKIP UP”
(17)
OR “SKIP DOWN”
(18) BUTTON TO SELECT FILE FORWARD OR BACKWARD.
SKIP UP
/ SKIP DOWN BUTTON
- DURING MP3/WMA PLAYBACK, PRESS “SKIP UP” (17) BUTTON ONCE TO PLAY THE NEXT
FILE. PRESS AND HOLD “SKIP UP” (17) BUTTON CONTINUOUSLY TO SPEED UP
SELECTING FORWARD.
- DURING MP3/WMA PLAYBACK, PRESS
“SKIP DOWN” (18) BUTTON ONCE TO PLAY THE
PREVIOUS FILE.
PRESS AND HOLD “SKIP DOWN” (18) BUTTON CONTINUOUSLY TO
SPEED UP SELECTING BACKWARD.
FOLDER SEARCHING
- TUNING THE TUNING KNOB (16) LEFT AND RIGHT TO SEARCH FOLDER BACKWARD OR FORWARD
REMARK
- THE SYSTEM CAN DETECT AND READ THE FILE UNDER MP3 AND WMA FORMAT ONLY THOUGH THE
USB PORT OR SD CARD SLOT
- IF CONNECT THE SYSTEM TO MP3 PLAYER VIA THE USB SOCKET, DUE TO VARIANCES IN MP3
7
ENCODING FORMAT, SOME MP3 PLAYER MAY NOT BE ABLE TO PLAY VIA THE USB SOCKET. THIS IS
NOT A MALFUNCTION OF THE SYSTEM.
- THERE ARE NUMEROUS USB AND SD DEVICE PRODUCERS ARE. SOLUTION AND FORMAT ARE
VARIABLE BETEEN EACH OTHER. THEREFORE, WE DO NOT GARANTTEE THIS UNIT CAN SUPPORT ALL
USB AND SD DEVICE FROM EVERY BRAND.
- SD CARD CAN BE SUPPORED UP TO 8GB
MP3/WMA TRACK FORMAT REQUIREMENT:
- MP3 BIT RATE : 32 KBPS~256 KBPS AND WMA BIT RATE : 32 KBPS ~ 320 KBPS
TRACKS PROGRAMMING
UP TO 64 TRACKS CAN BE PROGRAMMED FOR MP3/WMA FILE AND PLAY IN ANY ORDER. BEFORE USE, BE
SURE THE SYSTEM IS AT STOP MODE BEFORE PROGRAMMING:-
1. SET IN USB/SD MODE & SET AT STOP MODE.
2. PRESS THE “PROG” (9) BUTTON, “MEM” WILL BE FLASHING ON LCD DISPLAY. MOREOVER, IT WILL
INDICATE PROGRAM NO. AND DIGITS FOR TRACK NO. TO BE PROGRAMMED.
3. SELECT A DESIRED TRACK BY PRESSING “
SKIP UP” (17) OR “SKIP DOWN” (18) BUTTON.
4. PRESS THE “ PROG” (9) BUTTON TO STORE THE TRACK INTO MEMORY.
5. REPEAT STEPS 3 AND 4 TO ENTER ADDITIONAL TRACKS INTO THE MEMORY IF NECESSARY.
6. WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS “PLAY/PAUSE” BUTTON
(13) TO PLAY THE TRACKS IN ASSIGNED ORDER.
7. SET FUNCTION SELECTOR (5) TO OTHER MODE (EG. PHONO, TUNER AND ETC) TO CANCEL
PROGRAMMING.
COPYING OF MP3/WMA FILE
THE SYSTEM ALLOWS YOU TO COPY THE FILE FROM USB TO SD OR SD TO USB BY 1 FILE, 1 FOLDER OR
ALL FILES.
I) COPY 1 TRACK
1. INSERT THE USB STORAGE MEDIA OR SD/MMC CARD, SET IN USB/SD MODE.
2. PRESS “
REC” BUTTON (3) DURING THE PLAYBACK OF THE COPYING TRACK, THEN “ONE” WILL BE
FLASHING ON THE DISPLAY. PRESS “REC” BUTTON (3) AGAIN TO CONFIRM.
3. THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY. COPYING IS PERFORMING NOW.
4. AFTER COMPLETING OF COPY, UNIT WILL STOP PLAYBACK AUTOMATICALLY.
5. DISPLAY WILL SHOW “END” AND BACK TO USB OR SD MODE.
II) COPY 1 FOLDER
1. INSERT THE USB STORAGE MEDIA OR SD/MMC CARD, SET IN USB/SD MODE & SET AT STOP MODE
AFTER UNIT READING.
2. TUNE THE TUNING KNOB (16) TO SELECT THE DESIRED FOLDER FOR COPYING.
3. PRESS “REC” BUTTON (3), THEN “ONE” WLL BE FLASHING ON THE DISPLAY. PRESS SKIP UP (17) /
SKIP DOWN
(18) BUTTON TO SELECT “FOL” ON THE DISPLAY. PRESS “REC” BUTTON (3) AGAIN TO
CONFIRM.
4. USB OR SD ICON WILL BE FLASHING ON THE DISPLAY. COPYING IS PERFORMING NOW.
5. WHEN THE USB OR SD ICON STOPS FLASHING, IT MEANS THAT THE FOLDER COPYING IS COMPLETED.
III) COPY ALL TRACK
1.INSERT THE USB STORAGE MEDIA OR SD/MMC CARD, SET IN USB/SD MODE & SET AT STOP MODE AFTER
UNIT READING.
2. PRESS “REC”
BUTTON (3), THEN “ONE” WLL BE FLASHING ON THE DISPLAY. PRESS SKIP UP (17) /
SKIP DOWN
(18) BUTTON TO SELECT “ALL” ON THE DISPLAY. PRESS “REC” BUTTON (3) AGAIN TO
CONFIRM.
4. USB OR SD ICON WILL BE FLASHING ON THE DISPLAY. COPYING IS PERFORMING NOW.
5. WHEN THE USB OR SD ICON WILL STOP FLASHING, IT MEANS THAT ALL TRACK COPYING IS COMPLETED.
REMARK:
- IF PRESS THE “
REC” BUTTON (3) DURING PLAYBACK OF USB OR SD MODE, THE FILE WILL COPY
FROM USB TO SD OR SD TO USB.
8
FILE DELETE FROM USB / SD CARD
THE SYSTEM IS ABLE TO ERASE THE FILE STORED INSIDE THE USB DRIVE OR SD CARD BY FOLLOWING:-
I) DELETE 1 TRACK
1. PRESS “DEL
” BUTTON (7) DURING THE PLAYBACK OF THE DESIRED TRACK, THEN “ONE” WILL BE
FLASHING ON THE DISPLAY. PRESS “DEL
” BUTTON (7) AGAIN TO CONFIRM.
2. “DEL” WILL BE SHOWN ON THE DISPLAY.
3. “DEL” WILL DISAPPEAR ON THE DISPLAY, IT MEANS THE TRACK IS DELETED.
II) DELETE 1 FOLDER
1. INSERT THE USB STORAGE MEDIA OR SD/MMC CARD, SET IN USB/SD MODE & SET AT STOP MODE
AFTER UNIT READING.
2. TUNE THE TUNING KNOB (16) TO SELECT THE DESIRED FOLDER FOR DELETING.
3. PRESS “DEL
” BUTTON (7), THEN “ONE” WLL BE FLASHING ON THE DISPLAY. PRESS SKIP UP (17) /
SKIP DOWN (18) BUTTON TO SELECT “DIR” ON THE DISPLAY. PRESS “DEL” BUTTON (7) AGAIN TO
CONFIRM.
4. “DEL” WILL BE SHOWN ON THE DISPLAY. AFTER “DEL” DISAPPEARS IT MEANS THE DESIRED FOLDER IS
DELETED.
II) DELETE ALL TRACK
1. INSERT THE USB STORAGE MEDIA OR SD/MMC CARD, SET IN USB/SD MODE & SET AT STOP MODE
AFTER UNIT READING.
2. PRESS “DEL
” BUTTON (7), THEN “ONE” WLL BE FLASHING ON THE DISPLAY. PRESS SKIP UP (17) /
SKIP DOWN (18) BUTTON TO SELECT “ALL” ON THE DISPLAY. PRESS “DEL” BUTTON (7) AGAIN TO
CONFIRM.
3. USB OR SD ICON WILL BE FLASHING ON THE DISPLAY. COPYING IS PERFORMING NOW.
4. WHEN THE USB OR SD ICON STOPS FLASHING, IT MEANS THAT ALL TRACK COPYING IS COMPLETED.
REMARK : ALL THE FILES INSIDE THE USB STORAGE MEDIA OR SD CARD WILL BE DELETED COMPLETELY
AFTER CONFIRMING TO “DEL” BUTTON.
REMOVING OF USB / MEMORY CARD
TO REMOVE THE USB / MEMORY CARD, TURN OFF THE POWER OR SWITCH THE FUNCTION MODE TO
EITHER CD, AUX OR TUNER FIRST. FOR USB PORT – UN-PLUG IT BY PULLING OUT THE USB SOCKET
DIRECTLY, FOR MEMORY CARD – PRESS THE MEMORY CARD INWARD & THEN RELEASE, NOW THE CARD
BEING PARTIALLY EJECTED AND YOU CAN REMOVE IT BY HAND.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Lenoxx TT600 is a versatile audio system that combines a turntable, cassette player, radio, and digital encoder. It allows you to play and encode vinyl records, cassette tapes, and external audio sources onto USB drives or SD cards. The system features a 33/45/78 RPM belt-driven turntable with auto-stop and a slot-in cassette player. It also has an AUX input for connecting external devices, such as CD players or MP3 players. Additionally, the TT600 includes a built-in AM/FM radio with digital readout and a headphone jack for private listening.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Soundmaster MCD 4500 USB Datasheet
-
Dosound Electronics TR-18CD User manual
-
Dosound Electronics TR-18CD-SP User manual
-
PyleHome PTT25UBT Owner's manual
-
AWA 2528 User manual
-
Boytone BT-25MB User manual
-
iTrak BT9682GB User manual
-
Crosley Radio CR2404A User manual
-
Pyle Vintage PTTCSM70BT User manual
-
