5
ENGLISH
X Charge until the green battery status LED (3) lights
(approximately 13-14 hours).
Make sure that the dc source, ie jump-starter, battery pack,
vehicle accessory outlet, etc., is 12 Vdc and is able to supply
at least 0.5 amps at 12 Vdc for eight hours. This means that
a battery pack should be charged with at least a 4 amp/hour
capacity.
Note: When using a vehicle's 12 Vdc accessory outlet as a
charging source, it may be necessary to turn on the vehicles
ignition to power the accessory outlet.
USE
Operating the spotlight (fig. B)
X Move the trigger lock (4) down to the off position.
X Press the trigger (10) to turn the spotlight on.
X Press the trigger (10) repeatedly at one second intervals to
advance the brightness level from dim to bright.
X To lock the trigger (10) in the on position, press the trigger
until the desired level of brightness is achieved, then move
the trigger lock (4) up to the on position.
X To shut the spotlight off, move the trigger lock (4) down to
the off position.
Using the built-in carry lanyard
X The carry lanyard (6) may be used to store or carry the
spotlight. Adjust the slide on the cords to keep the lanyard
secure around the supporting object.
MAINTENANCE
Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
X From time to time wipe the appliance with a damp cloth. Do
not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water.
Replacing the bulb (fig. D & E)
To replace the bulb (1), you will need a small cross-head
screwdriver and a replacement bulb as per the technical
data.
Warning! Do not touch the glass part of the bulb. Bulb life may
be shortened by installing a bulb with dirt or fingerprints on it.
The bulb (1) can be wiped clean with a cloth moistened with
alcohol based cleaner.
X Disconnect the spotlight from any charging adapters.
X Lift and push the rubber ring guard (2) forward toward the
front of the spotlight to reveal two small cross-head screws
(12) in the retaining ring(13).
X Remove and retain the two screws (12).
X Lift off the retaining ring (13), the glass lens (12) and the
rubber "O" ring (15) and set them aside.
X Carefully remove the reflector (16) and the bulb assembly.
X Disconnect the bulb wire (17) from the power wire.
X Unclip the retaining clip (18) from the flange of the
reflector (fig E).
X Remove the screw (19) and detach the wire.
X Remove the bulb (1) and detach the wire.
X Insert the replacement bulb (1) into the flange of the
reflector (16).
X Install the retaining clip (18) into the flange of the
reflector (16).
X Install the wire with the screw (19).
X Connect the bulb wire (17) to the power wire.
X Place the reflector (16) in position in the body of the
spotlight.
X Install the rubber "O" ring (15) in the groove around the
perimeter of the reflector (16).
X Install the glass lens (12) and the retaining ring (13) so that
the screw holes are aligned.
X Secure the retaining ring (13) with the two screws (12).
X Install the rubber ring guard (2).
Replacing the fuse in the vehicle dc power cord
X Remove the gold cap by turning it counter clockwise.
X Remove the rubber washer, centre pin and the spring.
X Remove the fuse.
X Fit a new fuse of the same type and size (0.5 A).
X Install the centre pin, spring and rubber washer.
X Install the gold cap by turning clockwise onto the plug.
Protecting the environment
Should you find one day that your appliance needs
replacement, or if it is of no further use to you,
think of the protection of the environment. Black &
Decker repair agents will accept old Black &
Decker tools and ensure that they are disposed of
in an environmentally safe way.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this