Hinge Pin
and Hitch Pin
Qty: 2
Qty: 2
Qty:2
Qty: 2
463831703
Items to Assemble:
2 Wheel Assemblies
2 Hitch Pins
2 Leg Extenders
Items to Assemble:
2 Leg Assemblies
1 Bottom Shelf
6 carriage Bolts
6 Wing Nuts
Qty: 6
Qty: 6
Place Bottom Shelf and Legs as shown.
After assembling tighten all Wing Nuts.
Right Side:
Attach 2 Carriage Bolts and Wing Nuts in
front and back.
Left Side:
Place 1 Carriage Bolt
and Wing Nut in upper hole only
Items to Assemble:
1 Grill Bottom
1 Heat Shield
4 Carriage Bolts
4 Wing Nuts
Items to Assemble:
2 Shelves
8 Wing Screws
Qty: 8
Items to Assemble:
1 Grill Lid
2 Hinge Pins
2 Hitch Pins
1 Handle
2 Wing Nuts
1 Logo Plate
Item to Assemble:
1 Wire Shelf
1 Panel
2 Push Pins
Qty: 2
placing tabs into slots on Bottom Shelf.
Attach with push pins.
A
B
Assemble front panel first by
Place Wire Shelf in 3rd hole from top.
A
B
Grate rest
Qty. 4
Qty.4
Attach Wheel Assembly with Hitch Pins
Items to Assemble:
1 Vaporiser Bar
1 Grate
1 Charcoal Pan or Grate holder
Push Vaporiser Bar down onto rest in
Grill Bottom
A Insert leg on warming
rack into grill bottom
D Flex leg wire down and
forward to secure on
hook of warming rack.
D
B Place U-shaped wires on back of
warming rack over straight wire.
B
Item to Assemble:
1 Warming Rack
1 Leg Wire
C
C
Place leg wire into U-shaped
wire on front of warming rack.
Straight Wire
Items to Assemble:
1 Straight Wire
2 Clips
2 Warming Rack Handles
To use the Charcoal Pan
remove the Vaporiser Bar and Grate
Attach handles between second and third wire from ends.
Hook end of handlve over back and pull to hook over front wire.
Attach clips on straight wire. Place
wire into lower hole on lid. Slide
clips to lid sides.
Items to Assemble:
2 Charcoal Channels
1 Charcoal Pan
A
B Rotate grate support wires up and insert into
holes on charcoal pan
Insert Charcoal Channels on rests in grill bottom
B
D Rotate warming rack
leg wire to back of grill
bottom
C Place warming rack
in upper position
on the wire grate
supports and the tray
onto tent frames in
grill bottom.
See pages 24 and 25 in the Use & Care Manual for Charcoal/Gas use.See pages 24 and 25 in the Use & Care Manual for Charcoal/Gas use.
A
Items to Assemble:
1 Grease Clip
1 Grease Cup
1 Tank Wire Support Bracket
Correct position of LP tank
and tank wire support
bracket after grill assembly
LP tank is sold separately. Fill and leak check
before attaching to grill and regulator.
See Use & Care to perform the “Burner Flame Check”
and important safety instructions before using.
• Failure to install can in clip will cause hot
grease to drop from bottom of grill with
risk of fire or property damage.
•Tank collar opening must face to front of
cart once tank is attached.
• Failure to install tank correctly may allow
gas hose to be damaged in operation,
resulting in the risk of fire.
Back of GrillBack
of
Grill
Hang grease clip from center of grill bottom.
Use the grease cup to hang from grease clip.
Grease Clip
Grease Cup
1
9
12
11
10
9
8
4
5
6
7
1
2
3
/
