Surround
Left
Surround
Back
Left
Surround
Back
Right
Surround
Right
Listener
TV
Sub
woofer
Front
Left
Surround
Left
Surround
Back
Left
Surround
Back
Right
Surround
Right
Listener
Front
Right
Center
Front
Wide Left
Front
Wide Right
Sub
woofer
TV
Front
High
Left
Front
High
Right
Speaker Layout (Main Room)
1/2''-5/8''
(12-15mm)
*1
Powered
subwoofer
Front
left
speaker
Front
wide left
speaker
Front
high left
speaker
Front
right
speaker
Front
wide right
speaker
Front
high right
speaker
Center
speaker
Surround back
right speaker
Surround
left speaker
Surround
right speaker
Surround back
left speaker
SN 29400040(C) Copyright 2009 ONKYO CORPORATION Japan. All rights reserved.
See the other side of this sheet for the AV component hookup.
Speaker Hookup
Thank you for purchasing this product.
This quick setup sheet shows the typical hookup method
for connecting speakers and AV components (DVD/BD player,
TV, cable/satellite receiver).
For more detailed hookup information and operating
instructions, please see the Instruction Manual.
QUICK SETUP
Model : DTR-50.1
* 2 9 4 0 0 0 4 0 *
*1 The same signal is output from each jack.
TV
HDMI
IN
TV
VIDEO 1
IN
HDMI
OUT
Antenna input
(e.g., RF IN)
Cable/
satellite
Cable/satellite
VIDEO
OUT
AUDIO
OUT
L
R
DIGITAL
OUT
COAXIAL
Antenna input
(e.g..RF IN)
DVD player
VIDEO
OUT
AUDIO
OUT
DIGITAL
OUT
COAXIAL
L
R
HDMI
OUT
DVD/BD player
AV Component Hookup
IF NO HDMI
See the other side of this sheet for the speaker hookup.
With an HDMI cable you can send both audio and video with a single cable,
making connecting simple and keeping wires neat.
If you have an HDMI-compatible TV and players, you can connect them
to the AV receiver with HDMI cables. Digital audio signals received
at HDMI IN input are output to the speakers and headphones connected
to the AV receiver.
If your TV or player doesn’t support HDMI, use the analog or digital
connections shown below.
Please ensure the monitor input
(VIDEO 1, VIDEO 2, VIDEO 3, etc.)
selected corresponds to actual
connection used.
Coaxial feed from
TV antenna
If you are not using
cable/satellite box,
please refer to the
instruction manual.
Coaxial feed from
TV antenna
If you are not using
cable/satellite box,
please refer to the
instruction manual.
Using the Digital Inputs
If there’s no sound, you’ll need to assign the
digital inputs as necessary.
If you connect your DVD player to the AV
receiver’s DIGITAL COAXIAL IN 1, and connect
your cable/satellite receiver to the DIGITAL
COAXIAL IN 3, as shown, it’s not necessary to
change the default assignments.
If there’s no picture on your TV, set the
“Monitor Out” setting to “Analog” by pressing
the [Monitor Out] button first.
Using the HDMI Inputs
If there’s no picture on your TV, you’ll need to
assign the HDMI inputs as necessary using the
onscreen setup menus.
If you connect your DVD/BD player to the AV
receiver’s HDMI IN 1, and connect your cable
or satellite receiver to HDMI IN 3, as shown,
it’s not necessary to change the default
assignments.
On the front panel
On the front panel
1. Input/Output Assign
1. Input/Output Assign
2. Speaker Setup
3. Audio Adjust
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Remote Controller Setup
9. Lock Setup
Menu
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
1–4. Digital Audio Input
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX
COAX 1
COAX 2
COAX 3
OPT 1
FRONT
1–2. HDMI Input
HDMI1
HDMI2
HDMI3
HDMI4
FRONT
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
1. Input/Output Assign
2. Speaker Setup
3. Audio Adjust
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Remote Controller Setup
9. Lock Setup
Menu
/