BLACK DECKER ORB72 Owner's manual

Page is loading ...

4

ENGLISH

(Original instructions)

Intended use

Your Black & Decker orb-it

TM

handheld vacuum cleaner

has been designed for light dry vacuum cleaning pur-

poses. This appliance is intended for household use only.

Safety instructions

@

Warning! Read all safety warnings and all

instructions. Failure to follow the warnings

and instructions listed below may result in

electric shock, re and/or serious injury.

@

Warning! When using battery-powered ap-

pliances, basic safety precautions, including

the following, should always be followed

to reduce the risk of re, leaking batteries,

personal injury and material damage.

u Read all of this manual carefully before using the

appliance.

u The intended use is described in this manual. The use

of any accessory or attachment or the performance

of any operation with this appliance other than those

recommended in this instruction manual may present

a risk of personal injury.

u Retain this manual for future reference.

Using your appliance

u Do not use the appliance to pick up liquids.

u Do not use the appliance to pick up any materials that

could catch re.

u Do not use the appliance near water.

u Do not immerse the appliance in water.

u Never pull the charger lead to disconnect the charger

from the socket. Keep the charger lead away from

heat, oil and sharp edges.

u This appliance is not intended for use by young or

inrm persons without supervision. Children must be

supervised to ensure they do not play with the appli-

ance.

After use

u Unplug the charger before cleaning the charger or

charging base.

u When not in use, the appliance should be stored in a

dry place.

u Children should not have access to stored appliances.

Inspection and repairs

u Before use, check the appliance for damaged or

defective parts. Check for breakage of parts, damage

to switches and any other conditions that may affect

its operation.

u Do not use the appliance if any part is damaged or

defective.

u Have any damaged or defective parts repaired or

replaced by an authorized repair agent.

u Regularly check the charger lead for damage. Replace

the charger if the lead is damaged or defective.

u Never attempt to remove or replace any parts other

than those specied in this manual.

5

ENGLISH

(Original instructions)

Additional safety instructions - batteries and

chargers

Batteries

u Never attempt to open for any reason.

u Do not expose the battery to water.

u Do not expose the battery to heat.

u Do not store in locations where the temperature may

exceed 40°C.

u Charge only at ambient temperatures between 10°C

and 40°C.

u Charge only using the charger provided with the appli-

ance/tool. Using the wrong charger could result in an

electric shock or overheating of the battery.

u When disposing of batteries, follow the instructions

given in the section "Protecting the environment".

u Do not damage/deform the battery pack either by

puncture or impact, as this may create a risk of injury

and re.

u Do not charge damaged batteries.

u Under extreme conditions, battery leakage may occur.

When you notice liquid on the batteries carefully wipe

the liquid off using a cloth. Avoid skin contact.

u In case of skin or eye contact, follow the instructions

below.

Warning! The battery uid may cause personal injury or

damage to property. In case of skin contact, immediately

rinse with water. If redness, pain or irritation occurs seek

medical attention. In case of eye contact, rinse immedi-

ately with clean water and seek medical attention.

Chargers

Your charger has been designed for a specic voltage.

Always check that the mains voltage corresponds to the

voltage on the rating plate.

Warning! Never attempt to replace the charger unit with a

regular mains plug.

u Use your Black & Decker charger only to charge the

battery in the appliance/tool with which it was sup-

plied. Other batteries could burst, causing personal

injury and damage.

u Never attempt to charge non-rechargeable batteries.

u If the supply cord is damaged, it must be replaced by

the manufacturer or an authorised Black & Decker

Service Centre in order to avoid a hazard.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

u The appliance/tool/battery must be placed in a well

ventilated area when charging.

Safety of others

u This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning the use of the appliance by a

person responsible for their safety.

u Children should be supervised to ensure that they do

not play with the appliance.

6

ENGLISH

(Original instructions)

Residual risks.

Additional residual risks may arise when using the tool

which may not be included in the enclosed safety warn-

ings. These risks can arise from misuse, prolonged use

etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When

using any tool for prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Electrical safety

Your charger has been designed for a specic voltage.

Always check that the mains voltage corresponds to the

voltage on the rating plate. Never attempt to replace the

charger unit with a regular mains plug.

Symbols on the charger

Warning! Read all of this manual carefully

before using the appliance.

#

This charger is double insulated; therefore no

earth wire is required. Always check that the

power supply corresponds to the voltage on

the rating plate.

$

The charging base is intended for indoor

use only.

Features

This tool includes some or all of the following features.

1. Power button

2. Handle

3. Handle reset button

4. Nozzle

5. Charging indicator

6. Dust collector cover

7. Cover release button

8. Charging base

9. Accessory caddy

10. Crevice tool

11. Brush tool

7

ENGLISH

(Original instructions)

Assembly

Accessories (g. A & B)

These models may be supplied with some of the following

accessories:

u An accessory caddy for storing your accessories.

u A crevice tool (10) for conned spaces.

u Brush tool (11) for furniture and stairs.

Fitting the accessory caddy (Fig. A)

u Place the edge of the charger base (8) on to the edge

of the accessory caddy (9).

u Insert the brush tool (11) onto the front of the crevice

tool (10) then push the crevice tool into the accessory

caddy.

Fitting the accessories (Fig. B)

u Lift the handle (2) until it clicks into place. The nozzle

(4) will automatically lift at the same time.

u Insert the crevice tool (10) into the front of the nozzle

(4). Make sure that it is pushed fully in. If the brush

tool (11) is required then insert the brush tool (11) into

the front of the crevice tool (10).

Use

u Before rst use, the battery must be charged for at

least 4 hours.

u Place the appliance on the charging base whenever it

is not in use.

Charging the battery (Fig. C)

u Place the appliance on the charging base (8)

u Plug in the charger. Switch on at the mains. The

charging indicator (5) will ash continuously (slowly)

u Leave the appliance to charge for at least $$ hours.

While charging, the charger may become warm. This is

normal and does not indicate a problem. The appliance

can be left connected to the charger indenitely. The

charging indicator (5) will be lit as long as the appliance is

connected to the plugged-in charger.

Warning! Do not charge the battery at ambient tempera-

tures below 10 °C or above 40 °C.

The charge is complete when the charging indicator (9)

lights continuously. The charger and the battery can be

left connected indenitely with the LED illuminated. The

LED will change to ashing (charging) state as the charger

occasionally tops off the battery charge. The charging

indicator (5) will be lit as long as the battery is connected

to the plugged-in charger.

u Charge discharged batteries within 1 week. Battery

life will be greatly diminished if stored in a discharged

state.

Note: The charger will not charge a battery if the cell

temperature is below approximately 0 °C or above

40 °C.

The battery should be left in the charger and the

charger will begin to charge automatically when the

cell temperature warms up or cools down.

8

ENGLISH

(Original instructions)

Battery diagnostics

If the appliance detects a weak battery, the charging

indicator (5) will ash at a fast rate when the power button

(1) is pressed. Proceed as follows:

u Place the appliance on the charging base (8)

u Plug in the charger. Switch on at the mains.

u Leave the appliance to charge for at least 4 hours.

If the appliance detects a damaged battery, the charging

indicator (5) will ash at a fast rate when the appliance is

on the charger base. Proceed as follows:

u Take the appliance and the charger to be tested at an

authorised services centre.

Note: It may take as long as 60 minutes to determine

that the battery is defective. If the battery is too hot

or too cold, the LED will alternately blink red, fast and

slow, one ash at each speed and repeat.

To open the appliance (g. D)

u Lift the handle (2) until it clicks into place.

The nozzle (4) will automatically lift at the same time.

To close the appliance (Reset the handle and

nozzle) (g. D)

u Press the handle release button (3).

The nozzle (4) and the handle (2) will fall together.

Switching on and off (g. E)

u To switch the appliance on, press and hold the power

button (1).

u To switch the appliance off, release the power button

(1).

Note: The handle must be in the open position or the

appliance will not turn on.

Optimising the suction force

In order to keep the suction force optimised, the lters

must be cleared regularly during use.

Emptying the appliance (g. F)

u Hold the appliance so that the dust collector cover (6)

is facing upwards.

u Press the cover release button (7) the dust collector

cover (6) will open.

u While holding the appliance over a bin or sink, lift out

the lter (12) and empty the contents of the appliance.

u Replace the lter.

u Close the dust collector cover (6).

Note: The lters are re-usable and should be cleaned

regularly.

Warning! Never use the appliance without the lters.

Optimum dust collection will only be achieved with clean

lters.

Maintenance and cleaning

Your Black & Decker cordless appliance has been

designed to operate over a long period of time with a mini-

mum of maintenance. Continuous satisfactory operation

depends upon proper appliance care and regular cleaning.

9

ENGLISH

(Original instructions)

Warning! Before performing any maintenance on cordless

appliances:

u Switch off and unplug the appliance.

u Or switch off and remove the battery from the appli-

ance if the appliance has a separate battery pack.

u Or run the battery down completely if it is integral and

then switch off.

u Unplug the charger before cleaning it. Your charger

does not require any maintenance apart from regular

cleaning.

Cleaning the appliance

u Regularly clean the ventilation slots in your appliance

using a soft brush or dry cloth.

u Regularly clean the outside of your appliance using a

damp cloth. Do not use any abrasive or solvent-based

cleaner.

u The inside of the dust bowl can be cleaned using a

soft brush or dry cloth.

Cleaning the lters

u The lters can cleaned using a soft brush or dry cloth.

u The lters can be washed in warm soapy water.

u Make sure that the lters are dry before re-tting.

Replacing the lters

The lters should be replaced every 6 to 9 months and

whenever worn or damaged.

Replacement lters are available from your Black &

Decker dealer: Filter part number VFORB10-XJ

Protecting the environment

Z

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do

not dispose of it with household waste. Make this product

available for separate collection.

z

Separate collection of used products and

packaging allows materials to be recycled

and used again. Re-use of recycled materials

helps prevent environmental pollution and

reduces the demand for raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have

reached the end of their working life. To take advantage of

this service please return your product to any authorised

repair agent who will collect them on our behalf.

You can check the location of your nearest authorised

repair agent by contacting your local Black & Decker ofce

at the address indicated in this manual. Alternatively, a list

of authorised Black & Decker repair agents and full details

of our after-sales service and contacts are available on the

Internet at: www.2helpU.com

10

ENGLISH

(Original instructions)

Battery (Fig. G)

Z

If you want to dispose of the product

yourself, the battery must be removed as

described below and disposed of in accord-

ance with local regulations.

u Discharge the battery by operating the appliance until

the motor stops.

u Using a screwdriver, carefully remove the decorative

facia (13) by inserting it into the recess (14) and lifting.

u Remove the four screws (15) holding the body of the

appliance together.

u Lift the housing cover away from the assembly.

u Lift out the battery pack / motor assembly.

u Detach all lead connections from the battery pack /

motor assembly.

u Remove battery pack / motor assembly.

u Place the battery pack in a suitable package to ensure

that the terminals can not be short-circuited.

u Take the battery to your service agent or to a local

recycling station.

Once removed, the battery can not be retted.

Technical data

ORB72 (H1)

Voltage V

dc

7.2

Battery

Type

Li-Ion

Weight kg

0.72

Charger

S010QV1400040

Input voltage V

ac

100-240

Output voltage V

ac

14

Current mA

400

Approximate

charge time

h

4

Weight kg 0.13

11

ENGLISH

(Original instructions)

Guarantee

Black & Decker is condent of the quality of its products

and offers an outstanding guarantee. This guarantee

statement is in addition to and in no way prejudices your

statutory rights. The guarantee is valid within the territories

of the Member States of the European Union and the

European Free Trade Area.

If a Black & Decker product becomes defective due to

faulty materials, workmanship or lack of conformity, within

24 months from the date of purchase, Black & Decker

guarantees to replace defective parts, repair products

subjected to fair wear and tear or replace such products to

ensure minimum inconvenience to the customer unless:

u The product has been used for trade, professional or

hire purposes;

u The product has been subjected to misuse or neglect;

u The product has sustained damage through foreign

objects, substances or accidents;

u Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service

staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You

can check the location of your nearest authorised repair

agent by contacting your local Black & Decker ofce at

the address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of

our after-sales service and contacts are available on the

Internet at: www.2helpU.com

Please visit our website www.blackanddecker.co.uk to

register your new Black & Decker product and to be kept

up to date on new products and special offers. Further

information on the Black & Decker brand and our range of

products is available at www.blackanddecker.co.uk

Page is loading ...

ENGLISH

Do not forget to register your product!

www.blackanddecker.co.uk/productregistration

Register your product online at www.blackanddecker.co.uk/

productregistration or send your name, surname and product

code to Black & Decker in your country

.

DEUTSCH

Vergessen Sie nicht, Ihr Produkt registrieren zu lassen!

www.blackanddecker.de/productregistration

Lassen Sie Ihr Produkt unter www.blackanddecker.de/pro-

ductregistration online registrieren oder schicken Sie Ihren

Nachnamen, Vornamen und den Produktcode an Black & Decker

in Ihrem Land.

FRANÇAIS

N’oubliez pas d’enregistrer votre produit !

www.blackanddecker.fr/productregistration

Enregistrez votre produit en ligne sur www.blackanddecker.fr/

productregistration ou envoyez vos nom, prénom et code produit

à Black & Decker dans votre pays.

ITALIANO

Non dimenticate di registrare il prodotto!

www.blackanddecker.it/productregistration

Registrate il prodotto online su www.blackanddecker.it/produc-

tregistration o inviate nome, cognome e codice del prodotto al

centro Black & Decker del vostro paese.

NEDERLANDS

Vergeet niet uw product te registreren!

www.blackanddecker.nl/productregistration

U kunt uw product online registreren op www.blackanddecker.

nl/productregistration of u kunt uw voornaam, achternaam en

productcode opsturen naar Black & Decker in uw land.

ESPAÑOL

¡No olvide registrar su producto!

www.blackanddecker.es/productregistration

Registre su producto on-line en www.blackanddecker.es/produc-

tregistration o envíe su nombre, apellidos y código de producto a

Black & Decker en su país.

PORTUGUÊS

Não se esqueça de registar o seu produto!

www.blackanddecker.pt/productregistration

Registe o seu produto online em www.blackanddecker.pt/

productregistration ou envie o seu nome, apelido e código do

produto para a Black & Decker no seu país.

SVENSKA

Glöm inte att registrera produkten!

www.blackanddecker.se/productregistration

Registrera produkten online på www.blackanddecker.se/

productregistration eller skicka namn och produktkod till

Black & Decker i landet du bor i.

Page is loading ...

90614303 REV-0 07/2014

Nederland Black & Decker Benelux Tel. +31 164 283 065

Joulehof 12, 4622 RG Bergen op Zoom Fax. +31 164 283 200

Norge Black&Decker Tlf. 45 25 13 00

Postboks 4613, Nydalen Fax. 45 25 08 00

0405 Oslo www.blackanddecker.no

Österreich Black & Decker Vertriebsges.m.b.H Tel. 01 66116-0

Oberlaaerstraße 248, A-1230 Wien Fax. 01 66116-614

Portugal Black & Decker Tel. 214667500

Centro de Escritórios de Sintra Avenida Fax. 214667580

Almirante Gago Coutinho, 132/134,

Edifício 142710-418 Sintra

2710-418 Lisboa

Suomi Black & Decker Oy Puh. 010 400 430

Tekniikantie 12, 02150 Espoo Faksi. 0800 411 340

Almirante Gago Coutinho, 132/134,

Edifício 142710-418 Sintra

Sverige Black & Decker AB Tel. 031-68 60 60

Box 94, 431 22 Mölndal Fax. 031-68 60 80

Türkiye KALE Hırdavat ve Makina A.Ş. Tel. 0212 533 52 55

Defterdar Mah. Savaklar Cad. No:15 Fax. 0212 533 10 05

Edirnekapı / Eyüp / İstanbul 34050

United Kingdom Black & Decker Tel. 01753 511234

210 Bath Road Fax. 01753 551155

Slough, Berkshire SL1 3YD

Middle East & Africa Black & Decker Tel. +971 4 8863030

P.O.Box - 17164 Fax. +971 4 8863333

Jebel Ali (South Zone), Dubai,

UAE

BLACK DECKER ORB72 Owner's manual

BLACK DECKER ORB72 Owner's manual

in other languages

Related papers

Other documents