DeWalt DWE4205 User manual

Page is loading ...

B

Copyright

DeWALT

English (original instructions) 3

Français (traduction de la notice d’instructions originale) 15

(



    : 29

Page is loading ...

ENGLISH

3

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work area safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personalinjuries.

Congratulations!

You have chosen a

DeWALT

tool. Years of experience, thorough

product development and innovation make

DeWALT

one of the

most reliable partners for professional power toolusers.

Technical Data

DWE4205 DWE4215

Voltage V

AC

220/240

127

220/240

127

Type 3 3

Power input W 1010 1200

No-load/rated speed min

-1

11500 11500

Wheel diameter mm 125 125

Wheel thickness (max) mm 6.0 6.0

Spindle diameter M14 M14

Spindle length mm 18.5 18.5

Weight kg 1.85 1.85

* weight includes side handle and guard

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.



CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.



Denotes risk of electricshock.



Denotes risk offire.

WARNING: To reduce the risk of injury, read the

instruction manual.

General Power Tool Safety Warnings



WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

English (original instructions)

SMALL ANGLE GRINDERS

DWE4205, DWE4215

4

ENGLISH

c ) Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-relatedhazards.

4) Power tool use and care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the

risk of starting the power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

5) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

ADDITIONAL SPECIFIC SAFETY RULES

Safety Instructions for All Operations

a ) This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool. Read

all safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure

to follow all instructions listed below may result in electric

shock, fire and/or seriousinjury.

b ) Operations such as polishing are not recommended

to be performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personalinjury.

c ) Do not use accessories which are not specifically

designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safeoperation.

d ) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed can

break and flyapart.

e ) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can not be

adequately guarded orcontrolled.

f ) Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted by

flanges, the arbour hole of the accessory must fit the

locating diameter of the flange. Accessories that do

not match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may cause loss

ofcontrol.

g ) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheel for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of

the rotating accessory and run the power tool at

maximum no-load speed for one minute. Damaged

accessories will normally break apart during this testtime.

h ) Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

5

ENGLISH

stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping flying

debris generated by various operations. The dust mask or

respirator must be capable of filtrating particles generated

by your operation. Prolonged exposure to high intensity

noise may cause hearingloss.

i ) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may fly away and

cause injury beyond immediate area ofoperation.

j ) Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or its

own cord. Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live" and

could give the operator an electricalshock.

k ) Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinningaccessory.

l ) Never lay the power tool down until the accessory

has come to a complete stop. The spinning accessory

may grab the surface and pull the power tool out of

yourcontrol.

m ) Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

yourbody.

n ) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electricalhazards.

o ) Do not operate the power tool near flammable

materials. Sparks could ignite thesematerials.

p ) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution orshock.

q ) Do not use Type 11 (flaring cup) wheels on this tool.

Using inappropriate accessories can result ininjury.

r ) Always use side handle. Tighten the handle securely.

The side handle should always be used to maintain control

of the tool at alltimes.

FURTHER SAFETY INSTRUCTIONS FOR ALL

OPERATIONS

Causes and Operator Prevention

of Kickback

Kickback is a sudden reaction to a pinched or snagged rotating

wheel, backing pad, brush or any other accessory. Pinching or

snagging causes rapid stalling of the rotating accessory which

in turn causes the uncontrolled power tool to be forced in the

direction opposite of the accessory’s rotation at the point of

thebinding.

For example, if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch

point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels may also

break under theseconditions.

Kickback is the result of tool misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below:

a ) Maintain a firm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start up. The operator can control torque reaction

or kickback forces, if proper precautions aretaken.

b ) Never place your hand near the rotating accessory.

Accessory may kickback over yourhand.

c ) Do not position your body in the area where power

tool will move if kickback occurs. Kickback will propel

the tool in direction opposite to the wheel’s movement at

the point ofsnagging.

d ) Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control

orkickback.

e ) Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent kickback

and loss ofcontrol.

Safety Warnings Specific for Grinding and

Abrasive Cutting-Off Operations

a ) Use only wheel types that are recommended for your

power tool and the specific guard designed for the

selected wheel. Wheels for which the power tool was not

designed cannot be adequately guarded and areunsafe.

b ) The grinding surface of centre depressed wheels

must be mounted below the plane of the guard lip.

An improperly mounted wheel that projects through the

plane of the guard lip cannot be adequatelyprotected.

c ) The guard must be securely attached to the power

tool and positioned for maximum safety, so the least

amount of wheel is exposed towards the operator.

The guard helps to protect the operator from broken wheel

fragments, accidental contact with wheel and sparks that

could igniteclothing.

d ) Wheels must be used only for recommended

applications. For example: do not grind with the side

of cut-off wheel. Abrasive cut-off wheels are intended

for peripheral grinding, side forces applied to these wheels

may cause them toshatter.

e ) Always use undamaged wheel flanges that are

of correct size and shape for your selected wheel.

Proper wheel flanges support the wheel thus

reducing the possibility of wheel breakage. Flanges

6

ENGLISH

for cut-off wheels may be different from grinding

wheelflanges.

f ) Do not use worn down wheels from larger power

tools. Wheel intended for larger power tool is not suitable

for the higher speed of a smaller tool and mayburst.

Additional Safety Warnings Specific for

Abrasive Cutting-Off Operations

a ) Do not "jam" the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive depth

of cut. Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheelbreakage.

b ) Do not position your body in line with and behind

the rotating wheel. When the wheel, at the point of

operations, is moving away from your body, the possible

kickback may propel the spinning wheel and the power

tool directly atyou.

c ) When wheel is binding or when interrupting a cut

for any reason, switch off the power tool and hold

the power tool motionless until the wheel comes to

a complete stop. Never attempt to remove the cut-

off wheel from the cut while the wheel is in motion

otherwise kickback may occur. Investigate and take

corrective action to eliminate the cause of wheelbinding.

d ) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind, walk up

or kickback if the power tool is restarted in theworkpiece.

e ) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own

weight. Supports must be placed under the workpiece

near the line of cut and near the edge of the workpiece on

both sides of thewheel.

f ) Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can causekickback.

Safety Warnings Specific for Sanding

Operations

a ) Do not use excessively oversized sanding disc

paper. Follow manufacturer’s recommendations,

when selecting sanding paper. Larger sanding paper

extending beyond the sanding pad presents a laceration

hazard and may cause snagging, tearing of the disc

orkickback.

Safety Warnings Specific for Wire Brushing

Operations

a ) Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress

the wires by applying excessive load to the brush.

The wire bristles can easily penetrate llight clothing and/

orskin.

b ) If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel

or brush may expand in diameter due to work and

centrifugalforces.

Additional Safety Rules for Grinders

• Threaded mounting of accessories must match the grinder

spindle thread. For accessories mounted by flanges, the arbor

hole of the accessory must fit the locating diameter of the

flange. Accessories that do not match the mounting hardware

of the power tool will run out of balance, vibrate excessively

and may cause loss ofcontrol.

• The grinding surface of the centre depressed wheels must

be mounted below the plane of the guard lip. An improperly

mounted wheel that projects through the plane of the guard

lip cannot be adequatelyprotected.



WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA or less.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the power supply corresponds to the voltage

on the rating plate.

Your

DeWALT

tool is double insulated in accordance

with EN60745; therefore no earth wire is required.



WARNING: 127 V units have to be operated via a fail-safe

isolating transformer with an earth screen between the

primary and secondary winding.

If the supply cord is damaged, it must be replaced by a

specially prepared cord available through the

DeWALT

serviceorganisation.

Mains Plug Replacement

(Middle East and Africa)

If a new mains plug needs to be fitted:

• Safely dispose of the oldplug.

• Connect the brown lead to the live terminal in theplug.

• Connect the blue lead to the neutralterminal.



WARNING: No connection is to be made to the

earthterminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 13A.

7

ENGLISH

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1.5 mm

2

; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

Package Contents

The package contains:

1 Angle grinder

1 Guard

1 Side handle

1 Backing flange

1 Threaded clamp nut

1 Hex key

1 Instruction manual

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

Date Code Position (Fig. A)

The date code

10

, which also includes the year of manufacture,

is printed into thehousing.

Example:

2017 XX XX

Year of Manufacture

Description (Fig. A, B)



WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

1

Spindle lock button

2

Spindle

3

Side handle

4

Backing flange

5

Clamp nut

6

Guard

7

Slider switch

8

Dust ejection system

Intended Use

Your heavy-duty small angle grinder has been designed

for professional grinding, sanding, wire brushing and

cuttingapplications.

DO NOT use grinding wheels other than centre depressed

wheels and flapdiscs.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

Your heavy-duty angle grinders is a professional power tool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

Anti-vibration Side Handle

The anti-vibration side handle offers added comfort by

absorbing the vibrations caused by thetool.

Dust Ejection System (Fig.A)

The dust ejection system

8

prevents dust pile-up around the

guard and motor inlet, and minimises the amount of dust

entering the motorhousing.

Soft Start Feature

DWE4205

The soft start feature allows a slow speed build-up to avoid an

initial jerk when starting. This feature is particularly useful when

working in confinedspaces.

No-Volt

DWE4205

The No-volt function stops the grinder restarting without the

switch being cycled if there is a break in the powersupply.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Be sure the

trigger switch is in the OFF position. An accidental start-up

can cause injury.

Attaching Side Handle (Fig.B)



WARNING: Before using the tool, check that the handle is

tightenedsecurely.

Screw the side handle

3

tightly into one of the holes on either

side of the gear case. The side handle should always be used to

maintain control of the tool at alltimes.

Accessories and Attachments

It is important to choose the correct guards, backing pads

and flanges to use with grinder accessories. Refer to chart

8

ENGLISH

at the end of this section for information on choosing the

correctaccessories.

NOTE: Edge grinding can be performed with Type27 wheels

designed and specified for thispurpose.



WARNING: Accessories must be rated for at least the

speed recom mended on the tool warning label. Wheels

and other accessories running over rated accessory speed

may burst and cause injury. Threaded accessories must

have a M14 hub. Every unthreaded accessory must have

a 22 mm arbor hole. If it does not, it may have been

designed for a circular saw and should not be used. Use

only the accessories shown in the chart at the end of this

section. Accessory ratings must be above listed minimum

wheel speed as shown on toolnameplate.

Mounting Guards



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Before

reconnecting the tool, depress and release the

trigger switch to ensure that the tool isoff.



CAUTION: Guards must be used with thisgrinder.

When using the DWE4205, DWE4215 grinder for cutting metal

or masonry, a Type 1 guard MUST be used. Type1 guards are

available at extra cost from

DeWALT

distributors.

NOTE: Please refer to the Grinding and Cutting Accessory

Chart at the end of this section to see other accessories that can

be used with thesegrinders.

Mounting and removing a fixed screw

guard (Fig. D)

1. Place the angle grinder on a table, spindle

2

up.

2. Align the lugs

12

with the slots

13

.

3. Press the guard

6

down and rotate it to the

requiredposition.

4. Securely tighten the screw

14

.

5. To remove the guard, slacken thescrew.



CAUTION: If the guard cannot be tightened by the

adjusting screw, do not use the tool. To reduce the risk of

personal injury, take the tool and guard to a service centre

to repair or replace theguard.

Mounting Closed (Type 1) guard.

1. Open the guard latch. Align the lugs

12

on the guard with

the slots

13

on the gearcase.

2. Push the guard down until the guard lug engages and

rotates freely in the groove on the gear casehub.

3. Rotate guard into desired working position. The guard body

should be positioned between the spindle and the operator

to provide maximum operatorprotection.

4. Close the guard latch to secure the guard on the gear case

cover. You should be unable to rotate the guard by hand

when the latch is in closed position. If rotation is possible,

tighten the adjusting screw with the clamp lever in the

closed position. Do not operate grinder with a loose guard

or clamp lever in openposition.

5. To remove the guard, open the guard latch, rotate the guard

so that the arrows are aligned and pull up on theguard.

NOTE: If, after a period of time the closed (Type 1) guard

becomes loose, tighten the adjusting screw with the clamp

lever in the closedposition.



CAUTION: If the guard cannot be tightened by the

adjusting screw, do not use the tool. To reduce the risk

of personal injury, take the tool and guard to authorized

repair agent to repair or replace theguard.

NOTICE: Do not tighten adjusting screw with clamp

lever in open position. Undetectable damage to guard or

mounting hub mayresult.

Flanges and Wheels

Mounting Non-Hubbed Wheels (Fig. E)



WARNING: Failure to properly seat the flange/ clamp nut/

wheel could result in serious injury (or damage to the tool

or wheel).



CAUTION: Included flanges must be used with depressed

centre Type 27 and Type 42 grinding wheels and Type41

cutting wheels. See the Accessories Chart for more

information.



WARNING: A closed, two-sided cutting wheel guard is

re quired when using cutting wheels.



WARNING: Use of a damaged flange or guard or fail ure

to use proper flange and guard can re sult in injury due to

wheel breakage and wheel contact. See the Accessories

Chart for more information.

1. Place the tool on a table, guard up.

2. Install the unthreaded backing flange

4

on spindle

2

with

the raised centre (pilot) facing the wheel.

3. Place wheel

16

against the backing flange, centreing the

wheel on the raised centre (pilot) of the backing flange.

4. While depressing the spindle lock button and with the

hex depressions facing away from the wheel, thread the

clampnut

5

on spindle so that the lugs engage the two

slots in the spindle.

5. While depressing the spindle lock button, tighten the

locking flange with a wrench

20

.

6. To remove the wheel, depress the spindle lock button and

loosen the threaded locking flange with a wrench.

Mounting Sanding Backing Pads (Fig. B, F)

NOTE: Use of a guard with sanding discs that use backing pads,

often called fiber resin discs, is not required. Since a guard is

not required for these accessories, the guard may or may not fit

correctly if used.



WARNING: Failure to properly seat the flange/ clamp nut/

wheel could result in serious injury (or damage to the tool

or wheel).



WARNING: Proper guard must be reinstalled for grinding

wheel, cutting wheel, sanding flap disc, wire brush or

9

ENGLISH

wire wheel applications after sanding applications are

complete.

1. Place or appropriately thread backing pad

17

on

thespindle.

2. Place the sanding disc

18

on the backing pad

17

.

3. While depressing spindle lock

1

, thread clamp nut

19

on

spindle, piloting the raised hub on the clamp nut into the

centre of san ding disc and backingpad.

4. Tighten the clamp nut by hand. Then depress the spindle

lock button while turning the sanding disc until the sanding

disc and clamp nut are snug.

5. To remove the wheel, grasp and turn the backing pad and

sanding pad while depressing the spindle lock button.

Mounting and Removing Hubbed Wheels

(Fig. A, B)

Hubbed wheels install directly on the M14 threaded spindle.

Thread of accessory must match thread of spindle.

1. Remove backing flange by pulling away from tool.

2. Thread the wheel on the spindle

2

by hand.

3. Depress the spindle lock button

1

and use a wrench to

tighten the hub of the wheel.

4. Reverse the above procedure to remove the wheel.

NOTICE: Failure to properly seat the wheel before turning

the tool on may result in damage to the tool or the wheel.

Mounting Wire Cup Brushes and

Wire Wheels (Fig. A)



WARNING: Failure to properly seat the flange/ clamp nut/

wheel could result in serious injury (or damage to the tool

or wheel).



CAUTION: To reduce the risk of personal injury,

wear work gloves when handling wire brushes and

wheels. They can become sharp.



CAUTION: To reduce the risk of damage to the tool,

wheel or brush must not touch guard when mounted

or while in use. Undetectable damage could occur to

the accessory, causing wires to fragment from accessory

wheel or cup.

Wire cup brushes or wire wheels install directly on the threaded

spindle without the use of flanges. Use only wire brushes or

wheels provided with a M14 threaded hub. These accessories

are available at extra cost from your local dealer or authorised

service centre.

1. Place the tool on a table, guard up.

2. Thread the wheel on the spindle by hand.

3. Depress spindle lock button

1

and use a wrench on the

hub of the wire wheel or brush to tighten the wheel.

4. To remove the wheel, reverse the above procedure.

NOTICE: To reduce the risk of damage to the tool, properly

seat the wheel hub before turning the tool on.

Prior to Operation

• Install the guard and appropriate disc or wheel. Do not use

excessively worn discs orwheels.

• Be sure the inner and outer flange are mounted correctly.

Follow the instructions given in the Grinding and Cutting

AccessoryChart.

• Make sure the disc or wheel rotates in the direction of the

arrows on the accessory and thetool.

• Do not use a damaged accessory. Before each use inspect

the accessory such as abrasive wheels for chips and cracks,

backing pad for cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or accessory is dropped,

inspect for damage or install an undamaged accessory. After

inspecting and installing an accessory, position yourself and

bystanders away from the plane of the rotating accessory

and run the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break apart

during this testtime.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Be sure the

trigger switch is in the OFF position. An accidental start-up

can cause injury.



WARNING:

• Ensure all materials to be ground or cut are secured

inplace.

• Secure and support the workpiece. Use clamps or a

vice to hold and support the workpiece to a stable

platform. It is important to clamp and support the

workpiece securely to prevent movement of the

workpiece and loss of control. Movement of the

workpiece or loss of control may create a hazard and

cause personalinjury.

• Support panels or any oversized workpiece

to minimize the risk of wheel pinching and

kickback. Large workpieces tend to sag under their

own weight. Supports must be placed under the

workpiece near the line of cut and near the edge of the

workpiece on both sides of thewheel.

• Always wear regular working gloves while operating

thistool.

• The gear becomes very hot duringuse.

• Apply only a gentle pressure to the tool. Do not exert

side pressure on thedisc.

• Always install the guard and appropriate disc or

wheel. Do not use excessively worn disc or wheel.

• Be sure the inner and outer flange are

mountedcorrectly.

• Make sure the disc or wheel rotates in the direction of

the arrows on the accessory and thetool.

• Avoid overloading. Should the tool become hot, let it

run a few minutes under no load condition to cool the

10

ENGLISH

accessory. Do not touch accessories before they have

cooled. The discs become very hot duringuse.

• Never work with the grinding cup without a suitable

protection guard inplace.

• Do not use the power tool with a cut-offstand.

• Never use blotters together with bonded

abrasiveproducts.

• Be aware, the wheel continues to rotate after the tools

is switchedoff.

Proper Hand Position (Fig.C)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the side handle

3

,

with the other hand on the body of the tool, as shown in

FigureC.

Slider Switch (Fig.A)



CAUTION: Hold the side handle and body of the tool

firmly to maintain control of the tool at start up and

during use and until the wheel or accessory stops rotating.

Make sure the wheel has come to a complete stop be fore

laying the tooldown.

NOTE: To reduce unexpected tool movement, do not switch

the tool on or off while under load conditions. Allow the grinder

to run up to full speed before touching the work surface. Lift the

tool from the surface before turning the tool off. Allow the tool

to stop rotating before putting itdown.



WARNING: Before connecting the tool to a power supply,

be sure the slider switch is in the off position by pressing

the rear part of the switch and releasing. Ensure the slider

switch is in the off position as described above after any

interruption in power supply to the tool, such as the

activation of a ground fault interrupter, throwing of a

circuit breaker, accidental unplugging, or power failure. If

the slider switch is locked on when the power is connected,

the tool will startunexpectedly.

To start the tool, slide the ON/OFF slider switch

7

toward

the front of the tool. To stop the tool, release the ON/OFF

sliderswitch.

For continuous operation, slide the switch toward the front of

the tool and press the forward part of the switch inward. To stop

the tool while operating in continuous mode, press the rear part

of the slider switch andrelease.

Spindle Lock (Fig.B)

The spindle lock

1

is provided to prevent the spindle from

rotating when installing or removing wheels. Operate the

spindle lock only when the tool is turned off, unplugged from

the power supply, and has come to a completestop.

NOTICE: To reduce the risk of damage to the tool, do

not engage the spindle lock while the tool is operating.

Damage to the tool will result and attached accessory

may spin off possibly resulting ininjury.

To engage the lock, depress the spindle lock button and rotate

the spindle until you are unable to rotate the spindlefurther.

Surface Grinding, Sanding and Wire

Brushing



CAUTION: Always use the correct guard per the

instructions in this manual.



WARNING: Metal dust build-up. Extensive use of flap

discs in metal applications can result in the increased

potential for electric shock. To reduce this risk, insert an

RCD before use and clean the ventilation slots daily by

blowing dry compressed air into the ventilation slots

inaccordance with the below maintenanceinstructions.

To perform work on a the surface of a workpiece:

1. Allow the tool to reach full speed before touching the tool

to the work surface.

2. Apply minimum pressure to the work surface, allowing

the tool to operate at high speed. Material removal rate is

greatest when the tool operates at high speed.

Angle

3. Maintain an appropriate angle between the tool and work

surface. Refer to the chart according to particularfunction.

Function Angle

Grinding 20˚-30˚

Sanding with Flap Disc 5˚-10˚

Sanding with Backing Pad 5˚-15˚

Wire Brushing 5˚-10˚

4. Maintain contact between the edge of the wheel and the

work surface.

- If grinding, sanding with flap discs or wire brushing

move the tool continuously in a forward and back

motion to avoid creating gouges in the worksurface.

- If sanding with a backing pad, move the tool constantly

in a straight line to prevent burning and swirling of

worksurface.

NOTE: Allowing the tool to rest on the work surface without

moving will damage the work piece.

5. Remove the tool from work surface before turning tool off.

Allow the tool to stop rotating before laying it down.



CAUTION: Use extra care when working over an edge, as

a sudden sharp movement of grinder may be experienced.

Precautions To Take When Working on a

Painted Workpiece

1. Sanding or wire brushing of lead based paint is NOT

RECOMMENDED due to the difficulty of controlling the

11

ENGLISH

contaminated dust. The greatest danger of lead poisoning is

to children and pregnant women.

2. Since it is difficult to identify whether or not a paint contains

lead without a chemical analysis, we recommend the

following precautions when sanding any paint:

Personal Safety

1. No children or pregnant women should enter the work area

where the paint sanding or wire brushing is being done

until all clean up is completed.

2. A dust mask or respirator should be worn by all persons

entering the work area. The filter should be replaced daily or

whenever the wearer has difficulty breathing.

NOTE: Only those dust masks suitable for working with lead

paint dust and fumes should be used. Ordinary painting

masks do not offer this protection. See your local hardware

dealer for the proper N.I.O.S.H. approved mask.

3. NO EATING, DRINKING or SMOKING should be done in the

work area to prevent ingesting contaminated paint particles.

Workers should wash and clean up BEFORE eating, drinking

or smoking. Articles of food, drink, or smoking should not be

left in the work area where dust would settle on them.

Environmental Safety

1. Paint should be removed in such a manner as to minimize

the amount of dust generated.

2. Areas where paint removal is occurring should be sealed

with plastic sheeting of 4 mils thickness.

3. Sanding should be done in a manner to reduce tracking of

paint dust outside the work area.

Cleaning and Disposal

1. All surfaces in the work area should be vacuumed and

thoroughly cleaned daily for the duration of the sanding

project. Vacuum filter bags should be changedfrequently.

2. Plastic drop cloths should be gathered up and disposed

of along with any dust chips or other removal debris. They

should be placed in sealed refuse receptacles and disposed

of through regular trash pick-up procedures.

During clean up, children and pregnant women should be

kept away from the immediate work area.

3. All toys, washable furniture and utensils used by children

should be washed thoroughly before being used again.

Edge Grinding and Cutting



WARNING: Do not use edge grinding/cutting wheels for

surface grinding applications because these wheels are

not designed for side pressures encountered with surface

grinding. Wheel breakage and injury may result.



CAUTION: Wheels used for edge grinding and cutting

may break or kick back if they bend or twist while the tool

is being used. In all edge grinding/cutting operations, the

open side of the guard must be positioned away from

theoperator.

NOTICE: Edge grinding/cutting with a Type27 wheel

must be limited to shallow cutting and notching—less

than 13mm in depth when the wheel is new. Reduce the

depth of cutting/notching equal to the reduction of the

wheel radius as it wears down. Refer to the Accessories

Chart for more information. Edge grinding/cutting with a

Type 41 wheel requires usage of a Type 1 guard.

1. Allow the tool to reach full speed before touching the tool

to the work surface.

2. Apply minimum pressure to the work surface, allowing

the tool to operate at high speed. Grinding/cutting rate is

greatest when the tool operates at high speed.

3. Position yourself so that the open-underside of the wheel is

facing away from you.

4. Once a cut is begun and a notch is established in the

workpiece, do not change the angle of the cut. Changing

the angle will cause the wheel to bend and may cause

wheel breakage. Edge grinding wheels are not designed to

withstand side pressures caused bybending.

5. Remove the tool from the work surface before turning

the tool off. Allow the tool to stop rotating before laying

itdown.

Metal Applications

When using the tool in metal applications, make sure that a

residual current device (RCD) has been inserted to avoid residual

risks caused by metal swarf.

If the power supply is shut off by the RCD, take the tool to an

authorised D

e

WALT repair agent.



WARNING: In extreme working conditions, conductive

dust can accumulate inside the machine housing when

working with metal. This can result in the protective

insulation in the machine becoming degraded with a

potential risk of an electrical shock.

To avoid build-up of metal swarf inside the machine, we

recommend to clear the ventilation slots on a daily basis. Refer

to Maintenance.

Cutting Metal

For cutting with bonded abrasives, always use the

guardtype 1.

When cutting, work with moderate feed, adapted to the

material being cut. Do not exert pressure onto the cutting disc,

tilt or oscillate the machine.

Do not reduce the speed of running down cutting discs by

applying sideward pressure.

The machine must always work in an upgrinding motion.

Otherwise, the danger exists of it being pushed uncontrolled

out of the cut.

When cutting profiles and square bar, it is best to start at the

smallest cross section.

Rough Grinding

Never use a cutting disc for roughing.

Always use the guard type 27.

The best roughing results are achieved when setting the

machine at an angle of 30° to 40°. Move the machine back and

forth with moderate pressure. In this manner, the workpiece

will not become too hot, does not discolour and no grooves

areformed.

12

ENGLISH

Cutting Stone

The machine shall be used only for dry cutting.

For cutting stone, it is best to use a diamond cutting disc.

Operate the machine only with additional dust protection mask.

Working Advice

Exercise caution when cutting slots in structural walls.

Slots in structural walls are subject to the country-specific

regulations. These regulations are to be observed under all

circumstances.Before beginning work, consult the responsible

structural engineer, architect or the construction supervisor.

MAINTENANCE

Your

DeWALT

power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Be sure the

trigger switch is in the OFF position. An accidental start-up

can cause injury.

Pop-off Brushes

The motor will be automatically shut off indicating that the

carbon brushes are nearly worn out and that the tool needs

servicing. The carbon brushes are not user-serviceable. Take the

tool to an authorised D

e

WALT repairagent.

Lubrication

Your power tool requires no additionallubrication.

Cleaning



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Optional Accessories



WARNING: Since accessories, other than those offered

by

DeWALT

, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only

DeWALT

recommended

accessories should be used with thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Max.

[mm]

Min.

Rotation

[min.

–1

]

Periphical

speed

[m/s]

Threaded

hole

length

[mm]

D b d

d

D

b

115 6 22,23 11 500 80 –

125 6 22,23 11 500 80 –

150 6 22,23 9 300 80 –

D

115 – – 11 500 80 –

125 – – 11 500 80 –

D

d

b

75 30 M14 11 500 45 20.0

D

115 12 M14 11 500 80 20.0

125 12 M14 11 500 80 20.0

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

household waste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

13

ENGLISH

Grinding and Cutting Accessory Chart

Guard Type Accessory Description How to Fit Grinder

Type 27

Guard

Depressed centre

grinding disc

Type 27 guard

Backing flange

Type 27 depressed

centre wheel

Threaded clamp nut

Flap wheel

Wire wheels

Wire wheels with

threaded nut

Type 27 guard

Wire wheel

Wire cup with

threaded nut

Type 27 guard

Wire brush

Backing pad/

sanding sheet

Type 27 guard

Rubber backing pad

Sanding disc

Threaded clamp nut

14

ENGLISH

Grinding and Cutting Accessory Chart (cont.)

Guard Type Accessory Description How to Fit Grinder

Type 1

Guard

Masonry cutting

disc, bonded

Type 1 guard

Backing flange

Cutting wheel

Threaded clamp nut

Metal

cutting disc,

bonded

Type 1

Guard

OR

Type 27

Guard

Diamond cutting

wheels

Page is loading ...

Afghanistan Ariana Hafiz Zabi Co. Ltd.

Dahan Bagh Squire Karte Ariana, Kabul, Afghanistan

[email protected] Tel: 93-0-799331079

Fax: 93-0-700007576 / 93-0-799331079

Algeria Sarl Outillage Corporation

08, Rue Med Boudiaf (ex TELLA Achen)

Cheraga, Alger

[email protected]

[email protected];

[email protected]

Tel: 213-0-21375130

213-0-21375131

Fax: 213-0-21369667

Angola Angoferraria, Lda.

Rua Robert Shields, nº 61, Luanda, Angola

[email protected]

Tel: 244-222-395837 / 244-222-395034

Fax: 244-222-394790

Azerbaijan Royalton Holdings Ltd.

41 Khagani St. Apt. 47 AZ1001 Baku- Azerbaijan

[email protected]

Tel: 994-12-4935544

Fax: 994-12-5980378

Egypt ElFarab S.A.E.

15-Nabil El Wakkad Street, Dokki,

Giza, Egypt

[email protected]

Tel: 202-37603946

Fax: 202-33352796

Ethiopia Seif Tewfik Sherif

Arada Sub City, Kebele 01/02, Global Insurance Bldg.,

2nd Flr., Room 43, P.O. Box 2525, Addis Ababa

[email protected]

Tel: 251-11-1563968

251-11-1563969

Fax: 251-11-1558009

Iraq Al-Sard Co. for General Trading Ltd

Jbara Bldg. 3Flr. Al Rasheed St., Baghdad, Iraq

[email protected] Tel: 964-18184102

Jordan Amman West Stores-Bashiti

210 Garden St. Tla’a Ali, P.O. Box 1564

Tla Ali Amman 11953, Jordan

[email protected]

Tel: 962-6-5350009

Fax: 962-6-5350012

Kenya Dextron Tools Ltd.

P.O. Box 20121-00200, Shariff House,

Kimathi Street, Nairobi

[email protected]

Tel: 254-20-6905000

254-20-2358021

Fax: 254-20-6905111 / 254-20-6905112

Lebanon Est. Shaya & Azar S.A.R.L.

Boulvard Jdeideh - Mar Takla - Bouchrieh .

P.O. Box 90545, Jdeideh. Beirut – Lebanon

[email protected] Tel: 961 1 872305

961 1 872306

Fax: 961 1 872303

Libya North Africa Trading ( El Ghoul Brothers)

P.O. Box 348, 7 October Street 11

Benghazi

[email protected]

Tel: 218-061-3383994

Fax: 218-092-7640688

North Africa Trading ( El Ghoul Brothers)

AlBarniq DeWALT Center,

Mokhazin-elsukar St. ElFallah, Tripoli

[email protected] Tel: 218-021-3606430

Fax: 218-092-6514813

North Africa Trading ( El Ghoul Brothers)

AlHilal Service Center Tawergha St., Misurata

Tel: 218-091-3221408

Mauritius Robert Le Marie Limited

Old Moka Road, Bell Village, P.O. Box 161,

Port Louis

[email protected]

Tel: 230-212 1865

230-212 2847

Fax: 230-2080843

Morocco Ets Louis Guillaud & Cie

31, Rue Pierre Parent,

Casablanca – 21000

[email protected]

Tel: 522-301446 / 305971 / 317815 / 315576

Fax: 522-444518 / 317888

Nigeria Meridian Power Tools Ltd.

Gr. Floor, #1 Alhaji Masha Rd, Next toTeslim Balogun

Stadium, Near National Stadium Surulere, Lagos, Nigeria

[email protected] Tel: 234-1-7740431

234-1-7740410

Fax: 234-1-7913798

Pakistan Northern Toolings (Pvt) Ltd.-Lahore

86- Railway Road, Lahore – 7

Pakistan

[email protected]

Tel: 92-423-7651220

92-423-7641675

Fax: 92-423-7641674

Northern Toolings (Pvt) Ltd.-Karachi

224-231 Industrial Town Plaza, Shahrah-e-Liaqat,

Karachi, Pakistan

[email protected] Tel: 92-213-2465305

92-213-2465307

Fax: 92-213-2465301

Northern Toolings (Pvt) Ltd.-Taxila

Al-Rehman Plaza, Opposite Tehsil Court,

Faisal Shaheed Road, Taxila

[email protected] Tel: 92-51-4545811

Fax: 92-51-4544194

South Africa Benray Tool Wholesalers C.C.

91 Turffontein Road, Stafford, Johannesburg, 2001 P.O.

Box 260037 EXCOM 2023, South Africa

[email protected]

Tel: 27-11-6838350

Fax: 27-11-6837456

Tanzania General Motors Investment Ltd.

14 Vingunguti-Nyerere Road, P.O.Box 16541,

Dar es Salaam, Tanzania

[email protected]

Tel: 255-22-2865022 / 2862661 / 2862671 /

2862659

Fax: 255-22-2862667

Tunisia Ets. Mohamed Ghorbel

03 Rue 8603 Charguia I Tunis.

Postal Code 2035

[email protected]

Tel: 216-71794248

216-71793848

Fax: 216-71770759

Uganda The Building Center ( 21 ) Ltd.

52 Station Road, Kitgum House,

P.O. Box 7436 Kampala, Uganda

[email protected]

Tel: 256-041-4234567

256-041-4259754

Fax: 256-041-4236413

Yemen Middle East Trading Co. (METCO)

5th Flr.Hayel Saeed Anam Bldg.

Al-Mugamma St. Taiz,

Yemen

[email protected]

Tel: 967-4-213455

Fax: 967-4-219869

Middle East Trading Co. (METCO)

Mualla Dakka,

Aden

[email protected]

Tel: 967-2-222670

Fax: 967-2-222670

Middle East Trading Co. (METCO)

Hayel st., Sana'a,

Yemen

[email protected]

Tel: 967-1-204201

Fax: 967-1-204204

UAE Black & Decker (Overseas) GmbH

P.O. Box 5420, Dubai

[email protected] Tel: 971-4 8127400 / 8127406

Fax: 971-4 2822765

Ideal Star Workshop Eqpt. Trading LLC

P.O. Box 37116, Al Quoz, Dubai

[email protected] Tel: 971-4 3474160

Fax: 971-4 3474157

Alebrah Engineering Service

P.O. Box 78954, Al Qusais, Dubai

[email protected] Tel: 971-4 2850044

Fax: 971-4 2844802

Burj Al Madeena

Industrial Area No. 1, opp. Pakistani Masjid

P.O. Box 37635, Sharjah

[email protected] Tel: 971-6 5337747

Fax: 971-6 5337719

McCoy Middle East LLC

P.O. Box 25793, Sharjah

[email protected] Tel: 971-6 5395931

Fax: 971-6 5395932

McCoy Middle East LLC

P.O. Box 10584, Ras Al Khaimah

[email protected] Tel: 971-7 2277095

Fax: 971-7 2277096

Al Sukoon Gen. Trdg. Co. LLC

P.O. Box 2975, Ajman

[email protected] Tel: 971-6 7435725 / 7438317

Fax: 971-6 7437350

Zillion Equipment and Spare Parts Trading LLC

P.O. Box 19740, opp. Bin Sadal / Trimix Redymix Sanaiya, Al Ain

[email protected] Tel: 971-3 7216690

Fax: 971-3 7216103

Light House Electrical, Abu Dhabi Branch

P.O. Box 120, Abu Dhabi

[email protected] Tel: 971-2 6726131

Fax: 971-2 6720667

Light House Electrical, Musaffah Branch

P.O. Box 120, Abu Dhabi

[email protected] Tel: 971-2 5548315

Fax: 971-2 5540461

Bahrain Alfouz Services Co. WLL

P.O. Box 26562, Tubli, Manama

[email protected] Tel: 973 17783562 / 17879987

Fax: 973 17783479

Kavalani & Sons W.L.L.

P.O. Box 71, Sitra, Manama

[email protected]

Tel: 973 17732888

Fax: 973 17737379

Kuwait Al Omar Technical Co.

P.O. Box 4062, Safat 13041, Kuwait

[email protected] Tel: 965 24848595 / 24840039

Fax: 965 24845652

Fawaz Al Zayani Establishment

P.O. Box 42426, Shop No.18,

Al Humaizi Commercial Complex, Khalifa Al Jassim, Shuwaikh

[email protected] Tel: 965 24828710

Fax: 965 24828716

Fawaz Al Zayani Establishment

Fahaheel Industrial Area, Main St., Sanaya

[email protected] Tel: 965 23925830

Fax: 965 24828716

Oman Al Jizzi Company LLC

P.O. Box 1704, P.C. 112, Ruwi

[email protected]

Tel: 968 24832618 / 24835153

Fax: 968 24831334 / 24836460

Al Hassan Technical & Construction Supplies Co. LLC

P.O. Box 1948, P.C. 112, Ruwi

[email protected]

Tel: 968 24810575 / 24837054

Fax: 968 24810287 / 24833080

Oman Hardware Co. LLC

P.O. Box 635, Ruwi Postal Code 112

[email protected] Tel: 968 24815131

Fax: 968 24816491

Khimji Ramdas

P.O. Box 19, Post Code 100, Ghala, Muscat

[email protected] Tel: 968 24595906/ 907

Fax: 968 24852752

Qatar Teyseer Industrial Supplies & Services Co. WLL

55, Al Wakalat St. (Between St. 18 & 19)

Salwa Industrial Area, P.O. Box 40523 Doha

[email protected]

Tel: 974 4581536

Fax: 974 4682024

Shaheen Electrical Works & Trading Co. WLL

Gate 34, St. 44 Industrial Area P.O. Box 9756, Doha

[email protected] Tel: 974 460 02 30 / 460 05 25

Fax: 974 460 13 38

KSA Industrial Material Organization (IMO)

P.O. Box 623, Rail Street, Riyadh

[email protected] Tel: 966-1 4028010 Ext. 26

Tel: 966-1 8001245757

Fax: 966-1 4037970

Fawaz Ebrahim Al Zayani Trading Est.

P.O. Box 76026, Al Raka : 31952

[email protected] Tel: 966-3 8140914

Fax: 966-3 8140824

MSS (Al-Mojil Supply & Services)

P.O. Box 450, Jubail 31951

Opp-Gulf Bridge Library & Riyadh House

[email protected]

Tel: 966-3 3612850 / 3624487

Tel: 966-3 3621729

Fax: 966-3 3623589 / 3620783

EAC (Al Yousef Contg. & Trdg. Est.)

P.O. Box 30377, Jeddah -21477

[email protected] Tel: 966-2 6519912

Fax: 966-2 6511153

Mohamed Ahmed Bin Afif Est.

P.O. Box 530, Yanbu, Al Bahr

[email protected] Tel: 966-4 3222626 / 3228867

Fax: 966-4 3222210

Garziz Trading for Bldg Mat & Decoration

P.O. Box 3364, Madina

[email protected] Tel: 966-4 826 14 90 / 822 76 36

Fax: 966-4 826 57 41

Sultan Garment Factory (RSC)

P.O. Box 29912, Riyadh 11467

[email protected] Tel: 966-1 4055148 / 4042889

Fax: 966-1 4055148

Al Bawardi Tools & Hardware

P.O. Box 112, Dammam 31411

[email protected]

Tel: 966-3 8330780 Ext. 24

Tel: 966-3 8348585 Ext. 24

Fax: 966-3 8336303

Al Bawardi Tools & Hardware

P.O. Box 68, Riyadh 11411

[email protected]

Tel: 966-1 4484999

Fax: 966-3 4487877

Al Bawardi Tools & Hardware

P.O. Box 16905, Jeddah 21474

[email protected]

Tel: 966-2 6444547 / 6439035

Tel: 966-2 6456095

Fax: 966-2 6439024

N521980 03/17

DeWalt DWE4205 User manual

This manual is also suitable for

DeWalt DWE4205 User manual

in other languages

Related papers

Other documents