Boston Loft Furnishings MS1071T0TX Installation guide

MS1071T0TX-ESPRESSO FINISH

MS1072T0TX-WHITE FINISH

MS1068T0TX-BLACK

SLIDING-DOOR WINDOW-PANE

MEDIA CABINET

Assembly Instruction

For assistance with assembly contact:

Southern Enterprises Inc.

Customer Service 1-800-633-5096

[email protected]

www.seidal.com

MS1071T0TX-ESPRESSO FINISH/MS1072T0TX-WHITE FINISH

MS1068T0TX-BLACK

SLIDING-DOOR WINDOW-PANE MEDIA CABINET

Please review all parts and hardware before disposing of any packaging. Call Customer Service if missing

hardware. Do not return to store/retailer. Using a screw that is too long will cause damage. Before beginning

assembly, separate each type of screw. Carefully study the screw diagrams below.You may receive extra

hardware with your unit.

A

TOP PANEL

B

LEFT SIDE PANEL

C

RIGHT SIDE PANEL

D

BASE

E

FIXED SHELVES

F

ADJUSTABLE SHELVES

G

RIGHT BACK PANEL

H

LEFT BACK PANEL

I

LEFT DOOR

J

RIGHT DOOR

1

CAM LOCK

2

COTTON MAT

3

CAM BOLT

4

BOLT

5

BARREL NUT

6

SHELF SUPPORTS

7

SCREW 1/8”x1/2”

8

DOWEL

9

SCREW5/32”x1-3/4”

10

PLASTIC ANCHOR

Care and Cleaning Instructions:

Before using, wipe with a clean, dry cloth.

Periodically apply furniture wax to renew the finish

on wood part. Avoid rubbing or Scratching the

surface with rough or abrasive objects.

For replacement parts or questions, please

call Customer Service at 1-800-633-5096.

Do not return product to store. Please call

manufacturer for assistance, questions or

parts.

Assembly Tool Required

No.2 Phillips Screw driver

Quantity

Of 1

Quantity

Of 1

Quantity

Of 1

Quantity

Of 1

Quantity

Of 2

Quantity

Of 3

Quantity

Of 4

Quantity

Of 1

Quantity

Of 1

Quantity

Of 1

Quantity

Of 1

Quantity

Of 10

Quantity

Of 10

Quantity

Of 10

Quantity

Of 4

Quantity

Of 4

Quantity

Of16

Quantity

Of 32

Quantity

Of 2

Quantity

Of 10

Quantity

Of 2

MS1071T

0

TX

-

ESPRESSO FINISH

MS1072T0TX-WHITE FINISH

MS1068T0TX-BLACK

SLIDING-DOOR WINDOW-PANE MEDIA CABINET

Assembly Instruction

FIGURE 1

Step 1:

PLEASE DO NOT OVER-TIGHTEN CAMBOLTS. PLEASE STOP

WHEN YOU FEEL TIGHT

PUT ALL PARTS ON A SOFT SURFACE TO PREVENT

SCRATCHES.

PLACE LEFT SIDE PANEL (B) SMOOTH SIDE ON FLAT SURFACE,

THEN SCREW 2 CAM-BOLTS (3) INTO PRETHREADED INSERT

HOLES ON SIDE PANEL (B) UNTIL STOP. (PLEASE DO NOT

OVERTIGHTEN CAM-BOLTS). ALSO PUSH 2 WOOD DOWELS (8)

INTO LARGE OPENING HOLES INTO LEFT SIDE PANEL (B).

REPEAT SAME PROCEDURE FOR RIGHT SIDE PANEL (C).

INSERT CAM-BOLTS (3), WOOD DOWELS (8) INTO PREDRILLED

HOLES ON ENDS OF FIXED SHELVES (E) AND FIT INTO

CORRESPONDING HOLES ON INSIDE OF LEFT AND RIGHT SIDE

PANELS (B, C). INSERT CAM-LOCKS (1) INTO BIG HOLES ON

INSIDE OF LEFT AND RIGHT SIDE PANELS (B, C) WITH SLOT

FOR SCREWDRIVER FACING OUTWARD. ROTATE CAM-LOCKS

(1) CLOCKWISE TO SECURE CAM-BOLTS (3). PUSH COVERS (2)

INTO CAM-LOCKS (1).

INSERT WOOD DOWELS (8) INTO PREDRILLED HOLES ON BASE

(D) AND FIT INTO CORRESPONDING HOLES ON BOTTOM

EDGES OF SIDE PANELS (B, C). INSERT BARREL NUTS (5) INTO

PREDRILLED HOLES ON INSIDE OF LEFT AND RIGHT SIDE

PANELS (B, C). INSERT MACHINE SCREWS (4) THROUGH

PREDRILLED HOLES ON UNDERSIDE OF BASE (D) AND

TIGHTEN INTO BARREL NUTS (5). PLEASE NOTE THAT IF

SCREWS DO NOT TIGHTEN, ROTATE BARREL NUTS (5) SO THAT

THREADS OF BARREL NUTS (5) FACING MACHINE SCREWS (4).

INSERT CAM-BOLTS (3), WOOD DOWELS (8) INTO PREDRILLED

HOLES ON UNDERSIDE OF TOP PANEL (A) AND FIT INTO

CORRESPONDING HOLES ON TOP EDGES OF LEFT AND RIGHT

SIDE PANELS (B, C). INSERT CAM-LOCKS (1) INTO BIG HOLES

ON INSIDE OF LEFT AND RIGHT SIDE PANELS (B, C) WITH SLOT

FOR SCREWDRIVER FACING OUTWARD. ROTATE CAM-LOCKS

(1) CLOCKWISE TO SECURE CAM-BOLTS (3). PUSH COVERS (2)

INTO CAM-LOCKS (1). AS SHOWN IN FIGURE 1.

FIGURE 2-

BACK VIEW SHOWN FOR ASSEMBLY PURPOSES.

FIGURE 3

Step 2:

ATTACH LEFT AND RIGHT BACK PANELS (H,

G) INTO SLOTS OF PARTS (A, B, C, D).

INSERT PAN HEAD WOOD SCREWS (7)

THROUGH PREDRILLED HOLES ON LEFT

AND RIGHT BACK PANELS (G, H) AND

TIGHTEN INTO REAR EDGES OF PARTS (A,

B, C, D, E). AS SHOWN IN FIGURE 2.

Step 3:

IN ORDER TO STAND STURDILY. DRILL TWO

3/16”DIAMETER HOLES ON WALL, THE

DISTANCE BETWEEN TWO HOLES TO BE 14”

AND SHOULD MATCH TO THE HANGING

HOLES ON BACK OF BACK PANELS (G, H).

FIT PLASTIC ANCHORS (10) INTO THE

HOLES ON WALL. USE SCREWDRIVER TO

FIT FLAT HEAD WOOD SCREWS (9)

THROUGH THE HANGING HOLES ON BACK

PANELS (G, H) INTO PLASTIC ANCHORS (10).

AS SHOWN IN FIGURE 3.

"Please mount at least 1 screw into a

wall stud. Wall anchor is not needed

when screwing directly into a wall

stud".

FIT SHELF SUPPORTS (6) INTO PREDRILLED

HOLES ON INSIDE OF LEFT AND RIGHT SIDE

PANELS (B, C). PUT ADJUSTABLE SHELVES

(F) ON EACH SHELF SUPPORTS (6)

MATCHING THE POSITION OF GROOVES ON

ADJUSTABLE SHELVES (F). AS SHOWN IN

FIGURE 3.

E

F

B

C

( 9)

WALL

( 10)

( 6)

( 10)

G

H

14" W

E

Step 4:

FIT LEFT AND RIGHT DOORS (I, J) INTO GROOVES ON TOP PANEL AND BASE (A, D). AS SHOWN IN FIGURE 4.

AFTER LOCKING THE DOORS,IF THE GAP BETWEEN SIDE PANEL(S) AND DOOR IS UNEVEN,YOU CAN ADJUST

THE SCREWS ON TWO CASTERS ON THE BOTTOM OF DOORS TO GET EVEN GAP.

FIGURE 4

( I )

We'd love to hear from you! Email us photos of our products in your home at [email protected]om and we might

feature it on our site or use it to model one of our inspirational photos.

“PARTS WILL BE SENT IF AVAILABLE FROM SEI” “THIS IS NOT A WARRANTY”

Parts Replacement Form

Customer Information

Name

Address

City/State/Zip Code

Phone Number

Please indicate where you purchased this item: Store/ Website/ Catalog

Please indicate color/size/style number:

Style No Parts Letter Parts Description Quantity Needed

Please count, identify and compare parts and hardware list to be sure all parts are present. It may help to divide

parts and label them to correspond with part list. Extra hardware may be included. If any items are missing, please

contact Southern Enterprises at 800-633-5096 or in Dallas (972) 869-0111/ 9am – 4pm Mon-Fri Central time if you

have product issues with your purchase. Please ask for a customer service representative for issues involving

damages or replacement parts. Please ask for a technical assistance representative for any issues with product

assembly and product construction. Please contact the retailer that you purchased from for returns.

Missing or damaged hardware and/ or parts will be replaced free of charge. We do not sell parts. We do not

recommend modifying product(s) and we are not responsible for any damages due to product modification(s).

I

f this product has not been purchased from our retail affiliates (within 9 months), we are under no obligation to

Customer Service 1-800-633-5096

[email protected]

Southern Enterprises, Inc.

600 Freeport Parkway, Suite 200

Coppell, Texas 75019

Boston Loft Furnishings MS1071T0TX Installation guide

This manual is also suitable for

Boston Loft Furnishings MS1071T0TX Installation guide

Related papers

Other documents