Luxor MSP130 User manual

JIGSAW SSG450

INSTRUCTION MANUAL

SVENSKA / ENGLISH

Page is loading ...

INNEHÅLLSFÖRTECKNING / TABLE OF CONTENT

SVENSKA

Säkerhetsföreskrifter .................................. 5-9

Delar ...................................................... 10

Användning ..........................................11-12

Skötsel och underhåll ................................. 13

Speciﬁkationer .......................................... 14

Information .............................................. 15

ENGLISH

Safety Instructions .................................. 16-20

Parts ....................................................... 21

Operation ........................................... 22-23

Maintenance ........................................... 24

Speciﬁcations ........................................... 25

Information .............................................. 26

Page is loading ...

16 | ENGLISH

GENERAL POWER TOOL SAFETY

WARNINGS

WARNING: Read all safety warnings

and all instructions. Failure to follow the

warnings and instructions may result

in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive

atmospheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause you

to loose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

• If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

SAFETY INSRTUCTIONS

ENGLISH | 17

protected supply. Use of an RCD reduces the risk of

electric shock.

NOTE: The term residual current device (RCD)

may be replaced by the term ground fault circuit

Interrupter (GFCI) or earth leakage circuit breaker

(ELCB).

PERSONAL SAFETY

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inuence of drugs, alcohol or medication.

A moment of inattention while operating power

tools may result in serious personal injury.

• Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will

reduce personal injuries.

• Prevent unintentional starting. Ensure the switch

is in the OFF-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your ﬁnger on

the switch or energizing power tools that have the

switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-related hazards.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which

it was designed.

• Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

• Disconnect the plug from the power source and/

18 | ENGLISH

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool

accidentally.

• Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users.

• Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tools operation. If damaged, have the power tool

repaired before use. Many accidents are caused by

poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

SERVICE

• Have your power tool serviced by a qualied

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

SAFETY INSTRUCTIONS

Risk of injury

Do not rivet or screw any nameplates or

signs onto the power tool. The protective

insulation can thereby be rendered

ineffective. Adhesive labels are

recommended. Only use an undamaged

plug and cable. Do not treat any materials

that produce any particles that are

detrimental to health (e.g. asbestos).

Damage to property/material

Mains voltage must correspond with the

voltage speciﬁcations on the power tool.

Only use original accessories.

PERSONAL PROTECTIVE EQUIPMENT

• When using this power tool, wear the following

protective items: Protective glasses, ear protection,

breathing mask.

ENGLISH | 19

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush, saw

blade or any other accessory. Pinching or snagging

causes rapid stalling of the rotating accessory which

in turn causes the uncontrolled power tool to be

forced in the direction opposite of the accessory’s

rotation at the point of the binding. For example, if

an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the

material causing the wheel to climb out or kick out.

The wheel may either jump toward or away from

the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels

may also break under these conditions. Kickback

is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be

avoided by taking proper precautions as given

below.

• Maintain a ﬁrm grip on the power tool and

position your body and arm to allow you to resist

kickback forces. Always use auxiliary handle, if

provided, for maximum control over kickback or

torque reaction during start-up. The operator can

control torque reactions or kickback forces,

if proper precautions are taken.

• Never place your hand near the rotating

accessory. Accessory may kickback over

your hand.

• Do not position your body in the area

where power tool will move if kickback

occurs. Kickback will propel the tool in direction

opposite to the wheel’s movement at the point

of snagging.

• Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

• Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create

frequent kickback and loss of control.

SAFETY WARNINGS SPECIFIC FOR JIGSAW

OPERATIONS

• Do not use for cutting pipes or cables.

• Do not use cracked, blunt or damaged blades.

• Do not start the saw if no blade is ﬁtted.

• Check there are no obstructions in/on the surface

under the item to be cut.

20 | ENGLISH

• Do not attempt to cut items thicker than the

maximum cutting depth of the blade, or where

there is insufﬁcient space for the blade under the

item.

• The saw’s metal parts may become conductive

if the saw comes into contact with a live wire.

Therefore only hold the saw by its insulated

handle.

• Check that the ventilation slots are not blocked.

• Always use a face mask if excessive amounts of

dust are generated or cutting harmful materials.

• Never remove dust, obstructions or the like from

the work area while the blade is operating.

• Never stop the saw blade by applying pressure

to the saw or to the side of the blade.

• Do not lift the saw from the item being cut if the

blade is still running.

• Never place the saw on a table or workbench

if it has not stopped completely. The saw blade

will continue to run a short time after the machine

has been switched off.

• Do not touch the blade or metal ﬁlings until they

have cooled.

• Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a “live” wire

may make exposed metal parts of the power

tool “live” and could give the operator an electric

shock.

EXPLANATION OF SYMBOLS

To reduce the risk of injury, user must

read the instruction manual.

Always use protective glasses.

Always use ear protection.

Always use protective mask.

Double insulation.

ENGLISH | 21

PARTS

1. ON/OFF switch

2. Lock-on button

3. Dust extraction outlet

4. Soleplate

5. Safety guard

6. Saw blade holder

7. Guide roller

8. Clamping screw for

blade holder

9. Saw blade

10. Clamping screw for

soleplate

1 2

3

4

5

6

4 9 10

8

6 7

Figure 1 Figure 2 Figure 3

22 | ENGLISH

OPERATION

REPLACING SAW BLADES (SEE FIGURE 1)

• Disconnect the saw from the mains.

• Loose the saw blade clamping screws (8) through

the slot on the safety guard (5) by the aid of

hexagon key supplied with the tool.

• Remove the blade from the holder, insert a

replacement and retighten the screws.

• Pull the saw blade to check that it is correctly

positioned and locked in place. Make sure that

the back of the saw blade engages in the slot of

the guide roller (7).

• Connect the saw to the mains.

• Retain hexagon key in holder on saw to avoid

losing it.

ADJUSTING THE SOLEPLATE

• The soleplate (4) can be adjusted 45° (left or

right) in relation to the saw direction to facilitate

contour sawing. (See Fig. 2). Loosen the two

screws (10) under the soleplate, adjust the plate

to the desired angle and retighten the screws.

Angle setting can be seen on scale on top of the

soleplate.

SWITCH ON AND OFF

• Connect the plug to the power supply.

• To start the tool, depress the ON/OFF switch

trigger (1).

• When you release the switch trigger, the tool

turns off.

Note: For continuous operation, the switch button can

be locked by pressing the lock-on button (2) at the

same time as the switch trigger. The lock-on button

can be release by pressing the ON/OFF switch

trigger again.

GENERAL

• Never use a blade unsuitable for the task and

item to be cut.

• Hold the saw in front of you with a ﬁrm grip on

the handle.

• Ensure that the saw blade is not touching

anything and that the power cable is not in the

way when starting the saw.

• Make sure that the item is clamped tight, and that

the saw line is clearly marked.

ENGLISH | 23

• Connect the vacuum extractor nozzle to an

extractor system where possible.

• Start the saw. Place the soleplate on the item,

and let the saw blade touch the saw line.

• Saw, but do not place more pressure on the

blade than is necessary. Avoid lateral pressure

on the blade.

SPECIAL NOTES ON JIG SAWING

• Place the soleplate on the item so the saw blade

is vertical and correctly positioned in relation to

the saw line without touching it.

• Start the saw and tilt it carefully while supporting

it using the soleplate until the blade touches the

item at the saw line.

• Let the blade work through the item, continuing

to tip the saw downwards until the sole is ﬂush to

the item and the blade is perpendicular to it. If

necessary, drill a hole of suitable diameter in the

item for use as starting point.

SAWING WOOD

• Check that the item does not contain nails or

other metal objects. Always wear a mask.

SAWING METAL

• We recommend lubricating the material and

saw blade with cutting oil to protect the tool

and avoid overheating. Support the item with

wooden blocks on either side.

SAWING PLASTIC

• Make a test cut ﬁrst to check if the material can

tolerate the heat generated by sawing.

IMPORTANT!

Check all screws on the saw regularly, particularly

those that hold the blade. Tighten if required. Check

regularly that the carbon brushes are in a good

condition. If the carbon brushes are worn, they

should be replaced.

LUBRICATION (FIG. 1)

• Regularly apply a drop of oil to lubricate the

guide roller (7).

OPERATION

24 | ENGLISH

Caution: Always be sure that the tool is switched

off and unplugged before attempting to perform

inspection for maintenance. In order to maintain

product reliability and safety, repairs, replacement, any

other maintenance or adjustment, and carbon brush

inspection and replacement should be performed by

qualiﬁed service personnel.

• Wipe the saw using a well-wrung cloth after use,

and always keep the surface and ventilation holes

free of dirt. Keep the soleplate free of dirt to avoid

the saw cutting incorrectly.

• Never use corrosive or abrasive cleaning agents,

as they may attack the plastic parts of the saw.

• When the carbon brushes wear out the tool will

spark and/or stop. The brushes are a wearing

component of the tool and should be replaced

prior to the carbon wearing out fully. Always

replace both brushes at the same time.

• CAUTION: The carbon brushes must be replaced

by a pair similar carbon brush available through

the after-sales service organization or qualiﬁed

professional person.

• CAUTION: Always disconnect the machine from

the power supply before removing any electrical

covers.

• CAUTION: Do not use cleaning agents to clean

the plastic parts of the tool. A mild detergent on a

damp cloth is recommended. Water must never

come into contact with the tool.

CLEANING AND MAINTENANCE

ENGLISH | 25

Voltage AC 230V, 50Hz

Power rating 450W

No-load speed 2800 rpm

Max. cutting depth in Wood: 55 mm

Steel: 6 mm

Mitre angle 0-45°

• Jigsaw

• Saw blade (for wood)

• Wrench

• Instruction manual

TECHNICAL SPECIFICATIONS BOX CONTENT

26 | ENGLISH

ENVIRONMENT

Waste of Electrical and Electronic Equipment (WEEE) - WEEE Directive 2012/19/EU

This symbol on the product or in the instructions means that the electrical and electronic

equipment must be disposed of separately from other household waste when it does not

work anymore. The EU has separate waste collection systems, contact your local dealer

or authority for more information.

Batteries must be disposed of in special containers for battery disposal. They must not be

disposed of as household waste.

LAW AND SAFETY

This product has been manufactured according to current regulations for electromagnetic

ﬁelds (EMF), which means that it is safe to use if used according to safety instructions.

The product is manufactured according to current regulations within the EU legislation,

limiting the use of hazardous substances in electrical and electronic equipment (RoHS

Directive 2011/65/EU).

RESERVATIONS

We reserve the right to correct any typographical errors, and reserve the right to make

ongoing changes and improvements to the product and related materials.

Page is loading ...

Luxor MSP130 User manual

This manual is also suitable for

Luxor MSP130 User manual

in other languages

Other documents