Ci Mounting system
System overview
(1.1EN)
No. Description Code Load rating
(SWL)
[1]
Ci Mounting frame Z5145.000 240 kg (530 lb)
[2a]
2 x Ci Mounting brackets, 0° to 15° Z5146.015 160 kg (350 lb)
[2b]
2 x Ci Mounting brackets, 12° to 30° Z5146.030 160 kg (350 lb)
[2c]
2 x Ci Mounting brackets, 28° to 45° Z5146.045 160 kg (350 lb)
[3]
Rota Clamp Z5147.001 500 kg (1100 lb)
System overview (1.1EN)
Ci Mounting system
[1][1]→
←[3a]
[3a]
←[2 (a, b, c)][2 (a, b, c)]
←[3b][3b]
Z5145 Ci Mounting frame suspended with Z5147 Rota
clamp for attaching to overhead bars or truss
with a tube diameter up to 51 mm (2”) [3a].
Z5145 Ci Mounting frame suspended at the
outer plates using shackles and steel wire ropes
[3b].
Ci Mounting system
Description
The d&b Ci Mounting system is specially designed for
use with the d&b installation loudspeakers Ci3, Ci4-
TOP, Ci7-TOP and Ci-SUB.
A pair of mounting brackets [2] enable two cabinets
to be vertically arrayed with a defined range of
angles between them. There are three sets [2(a,b,c)],
each set enabling a different range of angle settings
between the cabinets, Z5146.015: 0°-15°, Z5146.030:
12°-30°, and Z5146.045: 28°- 45°.
The Z5145 Ci Mounting frame [1] is used to suspend
the cabinets either at the centre plate or left and
right using the outer plates. The entire cluster can be
vertically aligned, depending on which of the locating
holes of the mounting frame is used. The Z5147 Rota
clamp [3a] enables the horizontal alignment of the
cluster by suspending it from a single flying point
using the centre plate of the mounting frame. The
Rota clamp can be attached to overhead bars or
truss with a tube diameter up to 51 mm (2”).
Alternatively the Z5145 Ci Mounting frame can be
suspended at the outer plates using shackles and steel
wire ropes [3b].
The Ci Mounting system is constructed from powder
coated steel. Special colours (RAL paint finish) and a
weather resistant option are available on request.
System components and load ratings
The d&b Ci Mounting system is designed to comply
with BGV C1 Rule for the Prevention of Accidents.
Ci Mounting system
Z5146.015, Ci Mounting brackets
for vertical splay 0° to 15° [2a]
Z5146.030, Ci Mounting brackets
for vertical splay 12° to 30° [2b]
Z5146.045, Ci Mounting brackets
for vertical splay 28° to 45° [2c]
Vertical splay
Ci cabinet construction
The Ci3, Ci4-TOP, Ci7-TOP and Ci-SUB cabinets are
equipped with four M12 [4] threaded inserts for
attaching the Z5146.xxx Ci Mounting brackets, or the
Z5148 Ci Mounting bracket.
Another four M16 [5] threaded inserts are provide at
the side panels, top and the bottom panels of the
cabinet for attaching the Z5091 Ci Flying bracket.
Ci cabinet construction
[4]
[5]
D1503.E.01 (11/2006) © d&b audiotechnik AG
d&b audiotechnik AG, Eugen-Adolff-Str. 134, D-71522 Backnang, Germany, Phone +49-7191-9669-0, Fax +49-7191-95 00 00
/
