Bellini BDG301G-F Installation and User Manual

Brand: Bellini

Model: BDG301G-F

Type: Installation and User Manual

啊哈

Installation and User manual

Content

Safety instructions---------------------------------- 2

Product description--------------------------------- 4

Installation---------------------------------------------6

Start using your appliance--------------------------10

Maintenance and troubleshooting----------------12

Warranty------------------------------------------------ 14

20130114 issue 2

Black Glass Top-surface

Built-in Gas Cooktop

BDG604G, BDG604G-F, BDG604GA, BDG604GA-F

BDG302WG, BDG302WG-F, BDG302WGA, BDG302WGA-F

BDG302RG, BDG302RG-F, BDG302RGA, BDG302RGA-F

BDG301G, BDG301G-F, BDG301GA, BDG301GA-F

For warranty service call 1300 373 199(Australia)

or 0508 123108(New Zealand) to connect you to

the nearest authorised service centre

Safety Instructions

This manual explains the proper installation and use of your appliance, please read it

carefully before using even if you are familiar with the product. The manual should be kept

in a safe place for future reference. In case of failure, only the Authorized Technical

Service may repair this hob. Otherwise the guarantee will be null and void.

Warning

General Safety

The appliance may only be installed and connected

by licensed gasfitters / authorized persons.

z Built-in appliances may only be used after they have

built in to suitable built-in units and work surfaces

that meet local authority standards.

z In the event of faults with the appliance or damage

to the glass ceramic(cracks, scratches or splits), the

appliance must be switched off and disconnected

from the electrical supply, to prevent the possibility

of an electric shock.

z Repairs to the appliance must only be carried out by

trained registered authorized service persons /

engineers.

z The technical and identification data for the hob is

located on the reference data plate fixed to the

underside of the appliance.

z This reference data plate must be consulted before

making the electrical connections.

z The electrical connections must be made by

specialist installers to the legal and regulatory,

requirements in each country.

z If the cable is damaged in any way it must be

replaced by the manufacturer or after sale service

or by authorized technical staff, to avoid hazard.

Correct Use

z People (including children) who, because of their

physical, sensory or mental capabilities or their

inexperience or ignorance are not able to use the

device safely, should not use this device without

supervision or instruction by a responsible person.

z This appliance should be used only for normal

domestic cooking and frying of food.

z The appliance must not be used as a work surface

or as a storage surface.

z Additions or modifications to the appliance are not

permitted.

z Do not place or store flammable liquids,

highly inflammable materials or fusible

objects (e.g. plastic film, plastic, aluminum) on

or near the appliance.

z Do not heat an empty pan on the appliance.

Children’s Safety

z The cooking zones will become hot when you

cook. Therefore, always keep small children

away from the appliance.

z The appliance is not intended for use by

young children or infirm persons without

supervision.

z Young children should be supervised to

ensure that they do not play with the

appliance.

Safety During Use

z Remove stickers and film from the glass

surface.

z There is the risk of burns from the appliance if

used carelessly.

z Cables from electrical appliances must not

touch the hot surface of the appliance or hot

cookware.

z Overheated fats and oils can ignite very

quickly. Warning! Fire hazard!

z Switch the cooking zones off after each use.

z Users with implanted pacemakers should

keep their upper body at least 30 cm from

cooking zones that are switched on.

z Risk of burns! Do not place objects made of

metal, such as knives, forks, spoons and

saucepan lids on the cooking surface, as they

can get hot.

Safety Instructions

Safety When Installation

z Do not use or store flammable materials in the

appliance storage drawer or near this appliance.

z Do not spray aerosols in the vicinity of this

appliance while it is in operation.

z For Universal LPG appliance:- Where this

appliance is installed in marine craft or caravans,

it shall not be used as a space heater.

z This hotplate must be installed in accordance

with:

AS 5601 - Gas Installations (for Australia) –

current edition

NZS 5261 – Code of Practice for the Installation

of Gas Burning Appliances and Equipment (for

New Zealand) This standard may not be now

current!!

Local gas fitting regulations

AS/NZS 3000 – Electrical Installations (Wiring

Rules)

Building codes

Any other relevant statutory regulations.

z Check the gas type label on the underside of the

hotplate, adjacent to the gas connection to

ensure it corresponds to the installation gas

supply. If in doubt contact the supply authority.

z The power supply cord (supplied) must not touch

against any hot surfaces and must be placed so

that its temperature does not exceed 75 degrees

at any point along its length.

z After connecting to gas, check for leaks using

soapy solution, never a naked flame.

z Where a flexible hose assembly is used, ensure

it is approved to AS/NZS 1869, Class B 10mm

diameter and no more than 1.0metre in length.

Any hose assembly used must be restrained

from accidental contact with the flue outlet of an

under bench oven.

How To Avoid Damage To The Appliance

z The glass surface can be damaged by objects

falling onto it.

z The edge of the glass ceramic can be damaged

by being knocked by the cookware.

z Cookware made of cast iron, cast aluminum or

with damaged bottoms can scratch the glass

surface if pushed across the surface.

z Objects that melt and things that boil over can

burn onto the glass surface and should be

removed straightaway.

z Do not use the cooking zones with empty

cookware or without cookware.

z To avoid damaging cookware and glass

ceramics, do not allow empty saucepans or

frying pans to keep heating by the hob.

z The ventilation gap of 5mm between the worktop

and front of the unit underneath it must not be

covered.

z Do not modify this appliance.

Safety When Cleaning

z For cleaning, the appliance must be switched off

and cooled down.

z For safety reasons, the cleaning of the appliance

with steam jet or high pressure cleaning

equipment is not permitted.

Disposing Of The Device

When disposing of the device, do not bring it to regular municipal waste containers. Instead, bring

it to electrical and electronic waste recycling and reuse center. A relevant label has been put on the

device, its instructions manual, or the package. The device has been manufactured of recyclable

material. By bringing old device to recycling collection center, you show that you care about nature.

Ask your local environmental care authority for information on location of such facilities.

Product Description

BDG302W/RGA, BDG302W/RGA-F

*BDG302W/RG, *BDG302W/RG-F,

* have no aluminum trim

BDG604GA,

BDG604GA-F

*BDG604G,

*BDG604G-F

* have no aluminum trim

Trivet

Aluminum trim

Control knobs

Burner

Trivet

Aluminum trim

Control knobs

BDG301GA,BDG301GA-F

*BDG301G,*BDG301G-F,

* have no aluminum trim

Accessory

Name

Picture

( for reference only, physical unit maybe different)

Quantity

User Manual 1

Sealing tape 1 roll

Additional

labels

You have additional rating label in accessory bag, suggest

attach it onto a surface where it can be read e.g. inside

surface of adjacent cupboard

1 set

Installation

clip

4 sets

Screws

ST4.2x24

4 for BDG604G/A(-F), 3 for

BDG302*G/A(-F)&BDG301G/A(-F)

BDG604G/A(-F)

0.55mmx1, 0.7mmx2,

0.98mmx1

BDG302WG/A(-F)

0.7mmx1, 0.98mmx1

BDG302RG/A(-F)

0.7mmx1, 0.9mmx1

LPG Injectors

BDG301G/A(-F)

0.98mmx1

Elbow

&Washers

1 Elbow, 3 washers

Natural gas

regulator

Test point

adapter

Technical Specifications

Model

Product

Dimensions

(h x w x d) mm

Cut-out

Size

( w x d)mm

App’x net

weight

Electrical

Connection

Rated

Input

Power

BDG604G/A(-F) 105x584x510 552 x 470 12.7Kgs 220-240V/50Hz 0.5W

BDG302*G/A(-F) 100x300x510 266 x 478 7 Kgs 220-240V/50Hz 0.5W

BDG301G/A(-F) 100x300x510 266 x 478 6 Kgs 220-240V/50Hz 0.5W

Installation

Before Installation:

z Before cutting into any bench tops, ensure the minimum clearances to walls, adjacent surfaces and

overhead surfaces required by the relevant gas appliance installation code (see above) will comply.

Dimensions are specified in millimeters (mm)

Overhead cupboards and range hood = 650 mm.

Side and rear clearance = 200 mm to any burner edge.

Overhead exhaust/ceiling fan = 750 mm

Horizontal surfaces adjacent the hob = less than or equal to the hob height.

Ensure there is sufficient clearance to fit the regulator and/or flexible hose connection with the hotplate in

the installed position.

When you have installed the hob, make sure that

z The GPO(general purpose outlet) must always be in an accessible position.

z The supply connection point, test point and natural gas regulator adjustment screw (for Natural gas

installation) are accessible for testing and/or adjustment with the hotplate in the installed position.

1. Cupboard Cutting

Bench top thickness, 30– 40 mm (3 – 4 cm).

BDG604G(A)/BDG604G(A)-F

BDG302WG(A)/BDG302WG(A)-F/BDG302RG(A)

BDG302RG(A)-F/ BDG301G(A)/ BDG301G(A)-F

TO BE INSTALLED ONLY BY AN AUTHORIZED PERSON.

2. Place Burner Box

Apply the adhesive sealing tape to the underside lip of the burner box. Shown at G opposite.

Place burner box into cutout hole and fit clamping brackets to clamp the hotplate to the bench.

3. Fit Burners And Trivet.

Replace burners and ensure they are correctly repositioned over the ignitor (S) and thermocouple (T). The ignitor

(S) must be clean for trouble free sparking. Test burner ignition and burner flame for correct operation, If burner

is placed correctly it will not rotate on its supports

The Triple Ring (Wok) burner (diagrams below) does not fit over the igniter or thermocouple but must be placed

on its supports. Make sure trivet is fitted onto its locator on burners and can’t rotate after assembled.

3. Electrical Connection

Install a 10 amp general purpose outlet (GPO) in accordance with relevant electrical standards and/or codes of

practice applicable.

The power supply cord (supplied) must not touch against any hot surfaces and must be placed so that its

temperature does not exceed 75oC at any point along its length.

After having installed the hotplate, the GPO must always be in an accessible position.

Wiring diagram for

BDG604G/A(-F) Wiring diagram for BDG302*G/A(-F)

Wiring diagram for BDG301G/A(-F)

4. Gas Connection

Install in accordance with relevant gas standards and/or codes of practice

applicable.

Connect the elbow fitting to the appliance gas manifold connection, and check

that seals between the elbow and manifold connection are in place and in good

condition.

z For Natural gas: connect the natural gas appliance regulator (pictured

opposite) with integral test point using approved gas thread tape or

compound to the elbow fitting.

z For Universal LPG: connect the brass test point adaptor (pictured opposite)

using approved gas thread tape or compound to the elbow fitting.

Ensure the supply connection point, test point and natural gas regulator

adjustment screw (for Natural gas installation) are accessible for testing and/or

adjustment with the hotplate in the installed position.

Where a flexible hose assembly is used, ensure it is approved to

AS/NZS 1869, Class B. Any hose assembly used must be restrained

from accidental contact with the flue outlet of an under bench oven.

This hose assembly shall be suitable for connection to a fixed

consumer piping outlet located as follows:

Hotplates at a point 800 mm to 850 mm above the floor and in the

region outside the width of the appliance to a distance of 250 mm.

After connecting to gas, check for leaks using soapy solution, never a

naked flame.

Inlet connection region for flexible hose

Fit the duplicate data plate (supplied in separate bag) on a surface adjacent to the hotplate, for example, the

inside of the cupboard door so it is clearly visible for any service technician.

SETTING THE GAS PRESSURE:

Fit a manometer with a 6 mm rubber hose to the test point on the regulator (for natural gas).

For the Model BG604G/A(-F), light Triple Ring and Auxiliary burner on and adjust test point pressure to 1.00 kPa. Turn the two burners off

and on again and recheck the pressure is same as set previously or adjust as required.

For all the other models, light all burners on and adjust test point pressure to 1.00 kPa. Turn burners off and on again and recheck the

pressure is same as set previously or adjust as required.

TEST FOR CORRECT OPERATION:

After installation and adjusting burner pressure using test point, each burner ignition and operation must be

tested individually and with all burners operating. This testing must be done by the installer before leaving.

ADJUSTING THE BURNER MINIMUM FLAME HEIGHT:

NOTE: This adjustment can only be performed by the installer or an authorised service personnel.

The minimum burner flame is factory adjusted for the gas type stated on the gas type label adjacent to the gas

connection and should not require adjustment. Adjustment may be required if the hotplate has been converted

from Natural gas to Universal LPG or vice versa.

GAS CONVERSION INSTRUCTIONS:

The manufacturers servicing instructions detail how authorised personnel may convert the hotplate from Natural

gas to Universal LPG or from Universal LPG to Natural gas. Contact the manufacturer or agent as required.

NATURAL GAS UNIVERSAL LPG

Model

BDG604G/A(-F)

Injector Dia(mm) MJ/h Test point kPa Injector Dia(mm) MJ/h Test point kPa

Auxiliary 0.9 4 1 0.55 3.2 2.75

Semi rapid x2 1.1 6 1 0.7 5.5 2.75

Wok 1.7 12.5 1 0.98 10.8 2.75

TOTAL NHGC 28.5 25

NATURAL GAS UNIVERSAL LPG Model

BDG302WG/A(-F)

Injector Dia(mm) MJ/h Test point kPa Injector Dia(mm) MJ/h Test point kPa

Semi rapid 1.1 6 1 0.7 5.5 2.75

Wok 1.7 12.5 1 0.98 10.8 2.75

TOTAL NHGC 18.5 16.3

NATURAL GAS UNIVERSAL LPG Model

BDG302RG/A(-F)

Injector Dia(mm) MJ/h Test point kPa Injector Dia(mm) MJ/h Test point kPa

Semi rapid 1.1 6 1 0.7 5.5 2.75

Rapid 1.35 9 1 0.9 9 2.75

TOTAL NHGC 15 14.5

NATURAL GAS UNIVERSAL LPG Model

BDG301G/A(-F)

Injector Dia(mm) MJ/h Test point kPa Injector Dia(mm) MJ/h Test point kPa

Wok 1.7 12.5 1 0.98 10.8 2.75

TOTAL NHGC 12.5 10.8

Start Using Your Appliance

Description Explanation

Zone indicators

These show which zone is under control.

Flame power

Flame power of the zones, is the lowest and is the

highest.

The hotplates are fitted with mains powered electronic spark ignitors, so must be connected to mains power

supply (i.e. nominal 230 V ac) to operate. If power is not available, the hotplate will still work but the burners will

have to be lit with a match or similar.

Depressing the gas control knob of any burner will activate the spark ignition for all burners. To light the burner,

turn the gas control knob to the High Flame setting of the burner to be lit, while at the same time depressing the

gas control knob to activate the spark ignition.

Once the burner is alight continue to depress the gas control knob for 5 – 10 seconds to allow the flame

safeguard to activate. If when you release the gas control knob, the burner flame goes out the flame safeguard

has not heated up enough so repeat the ignition procedure after waiting 1 minute for gas to disperse. If problems

with burner lighting persist, refer to the TROUBLESHOOTING section of these instructions.

If power is not available, light a match or similar, then turn the gas control knob for the burner to be lit, to the

High Flame setting. Once again if problems with burner lighting persist, refer to the TROUBLESHOOTING

section of these instructions.

When burner lights, adjust desired flame height. On finishing, turn control knob to off position marked with a

black DOT.

BURNER AND UTENSIL CHOICE

Depending on the hotplate model, the burner choices are:

BDG604G/A(-F): Auxiliary (small), Semi-Rapid x2 (medium), and Wok (triple ring) burners.

BDG302WG/A(-F): Semi-Rapid (medium), Wok (triple ring)

BDG302RG/A(-F): Semi-Rapid (medium), Rapid (large)

BDG301G/A(-F): Wok (triple ring)

The maximum utensil (pan) diameters in millimetres

(mm) for each burner are:

1. For Natural Gas hotplates

Auxiliary (small) and Semi-Rapid (medium) =

195 mm

Rapid (large) = 230 mm

Triple ring (wok) = 270 mm

2. For Universal LPG hotplates

Auxiliary (small), Semi-Rapid (medium) and

Rapid (large) = 195 mm

Triple ring (wok) = 230 mm

The minimum utensil (pan) diameters in millimetres

(mm) for each burner are:

Auxiliary (small) = 80 mm

and Semi-Rapid (medium) = 140 mm

Rapid (large) and Triple ring (wok) = 195 mm

For best efficiency and to ensure utensil handle does

not overheat, place the utensil centrally on the burner

and adjust the flame height so all the flame remains

under the utensil.

NOTE: Enclosure may be circular or square

Do not place anything, eg. flame tamer, asbestos mat, between pan and

pan support as serious damage to the appliance may result.

Do not remove the pan support and enclose the burner with a wok stand

as this will concentrate and deflect heat onto the hotplate.

Do not use large pots or heavy weights which can bend the pan support

or deflect flame onto the hotplate.

Locate pan centrally over the burner so that it is stable and does not

overhang the appliance.

Use only a wok support supplied or recommended by the manufacturer of

the appliance.

Maintenance & Troubleshooting

Cleaning and maintenance should be carried out with

the appliance cold especially when cleaning the

enameled parts. Avoid leaving alkaline or acid

substances(lemon juice, vinegar etc.) on the surfaces.

STAINLESS STEEL

The stainless steel hob of the hotplate must be

cleaned regularly (e.g. weekly) to ensure long

life expectancy of the hotplate.

Ensure hotplate has cooled. Wash down with warm

soapy water and rinse with clean water.

Dry with a clean soft cloth. A specialized stainless

steel cleaning fluid may be used.

NOTE: Ensure that wiping is done along with the

grain of the stainless steel to prevent any unsightly

crisscross scratching patterns from appearing.

TRIVETS (UTENSIL SUPPORTS)

Enameled parts must only be washed with a sponge

and soapy water or with non-abrasive products. Rinse

with clean water. Dry with a clean soft cloth.

BURNERS

Remove trivets from

hob. Ensure burners

are cool. Remove the

burners enameled

cap (C) and aluminum

burner crown (F).

Wash down with

warm soapy water

and rinse with clean

water. Dry with a

clean soft cloth.

Use a cotton bud, tooth brush, or some other item to

clean out any incrustations or dirt from the four holes

marked(H)

Replace burners and ensure they are correctly

repositioned over the igniter (S) and thermocouple (T).

The igniter (S) must be clean for trouble free sparking.

Test burner ignition and burner flame for correct

operation.

The Triple Ring (Wok) burner (diagrams below) does

not fit over the igniter or thermocouple but must be

placed on its supports. If burner is placed correctly it

will not rotate on its supports.

TROUBLESHOOTING

Servicing of the hotplates must only be done by an authorised service representative (see back of this booklet) and the

hotplate must not be modified. Power must be disconnected before any servicing or maintenance is conducted.

It is recommended the hotplate serviced by an authorized person at least every 2 years. This service is not covered by

warranty.

Abnormal conditions include:

z Excessively yellow or sooting flame type.

z Flame lifting off the burner ports.

z Flame lighting back into the burner (normally associated with a popping sound).

z Objectionable odour of the flames combustion products.

Should a faulty condition develop in the hotplate that is not described above, refer to the following table first for possible

causes and remedies prior to contacting an authorised service representative. Servicing beyond the remedies listed

shall only be undertaken by an authorised service representative.

FAULT POSSIBLE CAUSE REMEDY

No power.

Check plugged in and switched on.

Check mains circuit breaker.

Loose sparker cable. Call authorised representative.

No spark when gas control

knob depressed.

Burner not aligned properly. Remove and re-fit burner.

Gas supply off. Check gas supply valve on.

Burner not aligned properly. Remove and re-fit burner.

Burner not lighting when

spark ignition working.

Burner ports blocked. Remove, clean and replace burner.

Flame safeguard not activated.

Re-light, allow more time for flame safeguard

to activate.

Burner goes out when

control knob released.

Flame safeguard faulty connection or

broken.

Call authorised representative.

Uneven flame pattern or

slight flame lifting.

Burner ports blocked. Remove, clean and replace burner.

At minimum flame setting

the flame is too high.

Turndown control setting incorrect. Call authorised representative.

Regulator faulty. Call authorised representative.

Gas supply pressure low. Call authorised representative.

Incorrect injector fitted. Call authorised representative.

Blocked injector or gas supply tube. Call authorised representative.

Small flame on High

setting.

Incorrect utensil size. Refer to operating instructions utensil choice.

Regulator faulty. Call authorised representative.

Incorrect injector fitted. Call authorised representative.

Flame too high on High

setting.

Incorrect utensil size. Refer to operating instructions utensil choice.

WARRANTY

1.1 In this warranty:

1.1.1 Australian Consumer Law means the law as set out in Schedule 2 of the Competition and

Consumer Act 2010;

1.1.2 Company means GSM Sales Pty Ltd ABN 53 007 682 475 of 142-144 Fullarton Road, Rose

Park SA 5067. Telephone 08 8122 2390. Email [email protected]

;

1.1.3 Consumer means a “consumer” as that term is defined in Section 3 of the Australian Consumer

Law as the original purchaser of a Bellini product;

1.1.4 Consumer Guarantees means the guarantees under the Australian Consumer Law;

1.1.5 You means the Consumer.

1.2 Nothing in this warranty affects any person’s rights under the Australian Consumer Law. The benefits to

any Consumer under this warranty are in addition to the rights and remedies available under any

Consumer Guarantees.

1.3 Subject to the other clauses of this warranty, the Company warrants to the Consumer that the Bellini

product will be free of manufacturing defects and will perform to the Company’s specifications.

1.4 The benefit of this warranty extends only to the Consumer as original purchaser of a Bellini product which

is installed in a residential property.

1.5 This warranty commences on the date of purchase of the Bellini product by the Consumer and continues

for the benefit only of the Consumer until the expiry of one (1) year (Warranty Period).

1.6 If within the Warranty Period a manufacturing defect is discovered in the Bellini product or it fails to perform

to the Company’s specifications as a result of some defect in materials, components or workmanship

(Defect) then the Company will, at its option, repair the Bellini product or supply a replacement Bellini

product free of charge. A replacement Bellini product may differ from the original product purchased by the

Consumer.

1.7 This warranty will not apply to any Bellini product:

1.7.1 Installed by any person other than a qualified tradesperson; or

1.7.2 Subjected to misuse, neglect, negligence or accidental damage; or

1.7.3 Operated in any way contrary to any operating or maintenance instructions; or

1.7.4 Improperly handled, installed or maintained; or

1.7.5 Altered or modified prior to or after installation; or

1.7.6 Damaged directly or indirectly by power surges, electrical storm damage or connection to incorrect

power supply

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY THE

CONSUMER MUST CALL 1300 373 199 (AUSTRALIA) OR 0508 123 108

(NEW ZEALAND) TO CONNECT TO THE NEAREST AUTHORISED CENTRE

TheAustralianConsumerLawrequirestheinclusionofthefollowingstatement

withthiswarranty:

Our goods come with guaranteed that cannot be excluded under the Australian Consumer Law. You are

entitled to a replacement or refund for a major failure and for compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods

fail to be of acceptable quality and the failure does not amount to a major failure.

1.8 You must provide proof of your purchase of the Bellini product and the date of purchase in order to obtain

the benefit of this warranty.

1.9 If you live outside the service area of the Company or one of its service agents, this warranty does not

cover the cost of transport of the Bellini product for service nor the service agent’s traveling costs to and

from your home.

1.10 If you are required to transport the Bellini product to the Company or its service agent, you must ensure it is

safely disconnected by a qualified tradesman and securely packed and insured. The Company does not

accept any responsibility for loss or damage of the Bellini product prior to it being received by the Company

or its service agent.

1.11 You will be responsible for all costs of returning a Bellini product to the Company and for redelivery of the

Bellini product by the Company (whether it is the original or a repaired and/or a replacement Bellini product)

and for any other expenses you incur in claiming under this warranty.

1.12 The Company or its service agent will examine any Bellini product and if the Company determines that it is

defective through no fault of the Owner and is otherwise undamaged, the Company will repair or replace

the Bellini product in accordance with this warranty.

DO NOT SEND IN THIS WARRANTY

Fill out the following details and file with your purchase invoice.

RETAIN & FILE WITH YOUR RECEIPT

Your Purchase Receipt/Invoice is proof of date of purchase. If you are unable to establish the date of purchase,

or if the fault is not covered by this warranty, or if the product is found to be in working order, you will be required

to bear all service call charges.

GSM Sales Pty Ltd reserves the right to discontinue items, modify designs and change specifications without

incurring obligation.

Whilst every effort is made to ensure that descriptions, specifications and other information in this publication is

correct, no warranty is given in respect thereof and the company shall not be liable for any errors therein.

Purchased from:

Co. Name:

Address:

Date of Purchase:

Serial number:

NOTE: Consistent with our continuing product development policy, improvements may have been made

which render the contents of this packaging slightly different to that shown.

FOR WARRANTY SERVICE CALL 1300 373 199 (AUSTRALIA)

OR 0508 123 108 (NEW ZEALAND) TO CONNECT YOU TO THE NEAREST

AUTHORISED SERVICE CENTRE

Bellini BDG301G-F Installation and User Manual

Bellini BDG301G-F Installation and User Manual

Bellini BDG301G-F Installation and User Manual

Related papers

Other documents