T 3DP -R adio F M 27 MH z. pmd PAG E 1 2005-11-12
T3DPS-FM
T3DPS-FM
FM 3CH DIGITAL PROPORTIONALR/C SYSTEM FOR
MODEL AIRPLANES
USER MANUAL
Made In China
T 3DP -R adio F M 27 MH z. pmd PAG E 2 2005-11-12
For your safety using, please read this
manual thoroughly.
TECHNICAL SPECIFICATIONS:
WARNING AND PRECAUTIONS
Type:----------------------------------------------------- T3DPS-FM27
Channel:------------------------------------------------- 3CH
Modulation:---------------------------------------------- FM
Frequency:---------------------------------------------- 27MHz
Working Voltage:-------------------------------------- 12V
Working Current:---------------------------------------120mA
* Read user manual carefully before putting the R/C into use.
* Do not oprate the system in open crowd.
* Do not oprate this system when models of the same
frequency are in use.
* Fully extend the antennas before operating.
* Remove batteries after use.
* Do not mix with old and new batteries.
* Do not mix different brands of batteries.
T 3DP -R adio F M 27 MH z. pmd PAG E 3 2005-11-12
For your safety using, please read this
manual thoroughly.
SYSTEM CONTENTS:
Items Unit
Piece
Transmitter
T3DPS-FM27
S-17(standard)
FM27-3CH
Servo Horn
Servo Horn Retention Screw
Servo Retention Screws
1
1
2
2
2
4
Receiver
Servo
Parts
Check if you have the above items, otherwise, please contact your local
distributor for assistance.
ANTENNA
BATTERY LEVEL INDICATOR
CH1 & CH2
CH1 SUB-TRIM
CH2 SUB-TRIM
CH3
CRYSTAL
REVERSING SWITCH
POWER SWITCH
Use for controlling the
speed of the motor of
the model.
Use for small
adjustments so that
model travels in
striaight line.
Use for small adjustments
to ensure model travel in
a level course
Use for controlling
directions of traveling
(left or right and up or
down).
Two LED display to indicate battery
voltage level. If the red led flashes
and beeping sound given out, replace
batteries.
Use for changing control
arm control direction.
1. TRANSMITTER
T3DP-Radio FM 27 MHz.pmd PAGE4 2005-11-12
BATTERIES INSTALLATION
Battery Cover
Receiving Antenna
Connecting To Receiver
Servo Horn
Servo Horn Retention Screw
* Remove battery cover at the
back of transmitter.
* Check carefully the polarity
markings before inserting
the 8 AA alkali or rechargeable
battery(not provided).
* Put back the battery cover.
BATT. Connect battery(4.8~6V)
CH.1 Connect a servo to
control the direction
of model.
CH.2 Connect a servo to
control the direction
of model.
CH.3 Connect to a speed
controller or servo.
CH.3
CH.2
CH.1
BATT.
X'TAL
2.RECEIVER
OUTPUT CONNECTOR
3. SERVO
Receiver FM27-3CH
T3DP-Radio FM 27 MHz.pmd
PAGE 5 2005-11-12
STORAGE
ASSEMBLY
1.Servo/Receiver Installation Diagram
2.Servo Horn Installation
CH.3
CH.2
CH.1
BATT.
X'TAL
Power Supply
(Input 4.8V-6V)
Connect to a Speed
Controller or servo
90
0
* After connecting servo to receiver,
turn on the power switch of the
transmitter and receiver.
* Ensure the trims on transmitter are
at neutral position.
* Install the servo horn according to
drawing.
* Store the R/C system in optimal conditions, keep away from
extreme hot or cold conditions.
* Keep away from dust or filthy environments.
* Do not drop or tamp the system.
Receiver FM27-3CH
T3DP-Radio FM 27 MHz.pmd
PA GE 6 2005-11-12
NOTE:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
"Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment."
/