GE JKD910SBSS Specification

GE
Brand
GE
Model
JKD910SBSS
Category
Warming drawers
Type
Specification

GE JKD910SBSS is a 27" warming drawer with a 1.67 cu. ft. capacity. It has variable temperature and humidity controls and comes with a half rack and a removable stainless steel pan. The full extension ball bearing glides make it easy to access your food, and the hidden controls provide a flush installation appearance. This warming drawer is a great way to keep your food warm and moist until you're ready to serve it.

GE JKD910SBSS is a 27" warming drawer with a 1.67 cu. ft. capacity. It has variable temperature and humidity controls and comes with a half rack and a removable stainless steel pan. The full extension ball bearing glides make it easy to access your food, and the hidden controls provide a flush installation appearance. This warming drawer is a great way to keep your food warm and moist until you're ready to serve it.

JKD910SBSS - GE Profile Performance
™
27” Warming Drawer
R
Listed by
Underwriters
Laboratories
25-1/2"
9-1/4"
Locate
electrical
outlet in
Adjacent
Cabinet
16" From
Left Side
or 42"
From Right
Side.
26-3/4"
10-1/2"
24"
Recommended
From Floor
For Under
Countertop
Installation
23"
23-1/2" Min.
Inside
9-1/4"
Locate Electrical
Outlet in Adjacent
Cabinet no Further
Than 16" From
Left Side or 42"
From Right Side.
10-1/2"
23"
23-1/2" Min.
Inside
1" Min.
Above
Toekick
or Adjust
to Oven
Installation
Height
2" Min.
Between
Cutouts
25-1/2"
26-3/4"
Electrical
Outlet 16" Max.
From Left Side.
23-1/2"
Min.
25"
1-1/2" Cabinet Top
36"
Countertop
Height
2" Min.
25-1/2"
9-1/4"
Electrical Outlet 42" Max.
From Right Side.
Electrical Outlet
Flush with Side
of Cabinet.
7" Max.
Specification Revised 8/99
Optional Accessories:
JXPN1–Optional Pan Set Accessory for
Warming Drawer.
Five commercial pans with lids (4” deep)
• One large pan (14 quarts)
• Two medium pans (6 quarts each)
• Two small pans (3 quarts each)
ZXD27B–1/4” wood panel trim kit
Important Installation Note:
Must provide anti-tip brace at the back of
the cabinet and the top of the cutout.
Note: When installing warming drawer
with a cooktop, allow a 2” minimum
from cooktop burner box bottom to top
of cut-out.
2x4 or 2x2
runners or Solid
Bottom
Install
2x4 or 2x2
Anti-Tip
Block 9"
From Floor
to Bottom
of Block
9
For answers to your Monogram,
®
GE Profile Performance Series,
™
GE Profile
™
or GE appliance questions, call
GE Answer Center
®
service, 800.626.2000.
Warming Drawer Dimensions (in inches)
Under Oven Installation (in inches)
Undercounter Installation (in inches)
Specification Revised 8/99
JKD910SBSS - GE Profile Performance
™
27” Warming Drawer
Features and Benefits
• 1.67 cu. ft Capacity
• Variable Temperature Control - Proof(80) / Low(140) / Med(170) / High(210)
• Variable Humidity Control - Crisp to Moist
• Half Rack
• "On" Signal Light
• On/Off Rocker Switch
• Removable Stainless Steel Pan
• Full Extension Ball Bearing Glides
• Hidden Controls Provide Flush Installation Appearance
• Variable Installation Options
• Model JKD910WBWW - White on white
• Model JKD910BBBB - Black on black
• Model JKD910ABAA - Almond on almond
• Model JKD910SBSS - Stainless steel
• Model JKD910CBCC - Bisque
  • Page 1 1
  • Page 2 2

GE JKD910SBSS Specification

GE
Brand
GE
Model
JKD910SBSS
Category
Warming drawers
Type
Specification

GE JKD910SBSS is a 27" warming drawer with a 1.67 cu. ft. capacity. It has variable temperature and humidity controls and comes with a half rack and a removable stainless steel pan. The full extension ball bearing glides make it easy to access your food, and the hidden controls provide a flush installation appearance. This warming drawer is a great way to keep your food warm and moist until you're ready to serve it.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers