Wacker Neuson G150 User manual

Category
Power generators
Type
User manual

This manual is also suitable for

Operator’s Manual
Notice d'emploi
Mobile Generator
Groupe électrogène mobile
G70, G100
G130, G150
Type G70, G100, G130, G150
Document
5100027140
Date 0217
Revision 02
Language
EN
-FR
5100027140
Copyright notice
© Copyright 2017 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the
machine. Any other type of reproduction is prohibited without express
written permission from Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker
Neuson Production Americas LLC represents an infringement of valid
copyrights. Violators will be prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their
respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original instructions
This Operator’s Manual presents the original instructions. The original
language of this Operator’s Manual is American English.
wc_tx004281gb_FM10.fm
3
Machine Identification
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machine
identification
A nameplate listing the model number, item number, revision number, and serial
number is attached to this machine. The location of the nameplate is shown above.
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine Item Number
G70 5200023226, 5200023227, 5200023228, 5200023974, 5100018635,
5100021959
G100 5100033310, 5100033311, 5100033312
G130 5200023232, 5200023233, 5200023234, 5100018637, 5100022091
G150 5200022870, 5200023235, 5200023236, 5200023237, 5100018638,
5100022092
wc_gr013470
R
Serial Number
159047
hz
215429
For electrical
equipment only.
Pour material
electrique
seulement.
amb.temp.
Rev.
Type/Model
Item Number
rpm
lbs
PRIME RATING
kW/
kVA
V
A
kg
MADE
IN USA
Serial Number:
4 wc_tx004282gb_FM10.fm
Mobile Generator
Foreword
Foreword
Machine
documentation
â–  From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
■ Keep a copy of the Operator’s Manual with the machine at all times.
â–  For spare parts information, please see your Wacker Neuson Dealer, or visit the
Wacker Neuson website at http://www.wackerneuson.com/.
â–  When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Expectations
for
information in
this manual
â–  This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
â–  Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
â–  The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change any
portion of this information without notice.
â–  The illustrations, parts, and procedures in this manual refer to Wacker Neuson
factory-installed components. Your machine may vary depending on the
requirements of your specific region.
CALIFORNIA
Proposition
65 Warning
Combustion exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental
discharge of sparks or flames from the engine exhaust. Spark arresters are
qualified and rated by the United States Forest Service for this purpose. In order to
comply with local laws regarding spark arresters, consult the engine distributor or
the local Health and Safety Administrator.
wc_tx004282gb_FM10.fm 5
Mobile Generator
Foreword
Manufacturer’s
approval
This manual contains references to approved parts, attachments, and
modifications. The following definitions apply:
â–  Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
â–  Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
â–  Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following
consequences:
â–  Serious injury hazards to the operator and persons in the work area
â–  Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
6 wc_tx004282gb_FM10.fm
Mobile Generator
Foreword
Notes
Table of Contents
G70 / G100 / G130 / G150
wc_bo5100027027_02_FM10T
7
Foreword 4
1 Safety Information 13
1.1 Signal Words Used in this Manual ..................................................... 13
1.2 Machine Description and Intended Use ............................................. 14
1.3 Safety Guidelines for Operating the Machine ..................................... 15
1.4 Service Safety .................................................................................... 17
1.5 Operator Safety while Using Internal Combustion Engines ............... 19
1.6 Safety Guidelines for Mobile Generators ........................................... 20
1.7 Safety Guidelines for Towing the Machine ......................................... 22
1.8 Safety Guidelines for Lifting the Machine ........................................... 23
1.9 Reporting Safety Defects ................................................................... 23
2 Label Locations 24
3 Label Meanings 26
4 Lifting and Transporting 38
4.1 Lifting the Machine ............................................................................. 38
4.2 Before Towing Checklist ..................................................................... 39
4.3 Towing the Machine ........................................................................... 40
4.4 Preparing the Machine for Transport on a Truck or Trailer ................ 41
4.5 Hazardous Materials Placards ........................................................... 42
4.6 Testing the Breakaway System—Hydraulic Surge Brakes ................. 43
4.7 Testing the Breakaway System—Electric Brakes .............................. 45
5 Machine Setup 47
5.1 Preparing the Machine for First Use ................................................... 47
5.2 Positioning the Machine ..................................................................... 48
5.3 Grounding the Generator ................................................................... 50
5.4 Recommended Fuel ........................................................................... 51
5.5 Refueling the Machine—Basler Controller ......................................... 52
5.6 Refueling the Machine—Deep Sea Controller ................................... 53
6 Operation, Control, and Component Locations 54
6.1 Control and Component Locations ..................................................... 54
6.2 Control Panel Components ................................................................ 55
Table of Contents
G70 / G100 / G130 / G150
wc_bo5100027027_02_FM10TOC.fm
8
7 Operation—Basler Controller 56
7.1 Engine Start Switch .............................................................................56
7.2 Genset Pre-Alarms and Alarms (Shut-Down Conditions) ...................57
7.3 Overcurrent Condition .........................................................................58
7.4 Using the Lugs and the Convenience Receptacles .............................59
7.5 Selecting the Voltage ..........................................................................60
7.6 Before Starting the Machine ................................................................62
7.7 Starting and Running the Machine ......................................................63
7.8 Stopping the Machine ..........................................................................66
7.9 Emergency Stop Switch ......................................................................66
7.10 LCD Panel: Monitoring Machine Operation .........................................67
8 Working with Basler Controller 69
8.1 How to Use the Genset Controller LCD and Keypad ..........................69
8.2 Menu Diagram of the Genset Controller ..............................................70
8.3 Menu Diagram Components ...............................................................71
8.4 Using the Metering and Settings Menus .............................................72
8.5 Logging in to the Genset Controller by Entering the Password ...........73
8.6 Adjusting the LCD Screen Contrast ....................................................76
8.7 Changing the Time/Date Settings .......................................................77
8.8 Changing the Sender Fail Time Delays ...............................................78
8.9 Changing the Units of Measure ...........................................................80
8.10 Changing the Low Fuel Pre-Alarm Setting ..........................................82
8.11 Changing or Disabling the Low Fuel Alarm Setting .............................84
8.12 Changing the Cooldown Time Setting .................................................86
8.13 Changing the Maintenance Interval .....................................................88
8.14 Resetting the Maintenance Interval Pre-Alarm ....................................90
8.15 Resetting a Loss of Voltage Pre-Alarm ...............................................92
8.16 Accessing and Using the Event Log ....................................................93
9 Operation—Deep Sea Controller 95
9.1 Main Circuit Breaker ............................................................................95
9.2 Genset Controller Power Switch .........................................................96
9.3 Selecting the Voltage ..........................................................................97
9.4 Deep Sea Controller Buttons/Functions ..............................................99
9.5 Genset Controller Alarms and Shut-Down Conditions ......................101
9.6 Before Starting the Machine ..............................................................103
9.7 Starting and Running the Generator .................................................104
9.8 Stopping the Generator .....................................................................106
Table of Contents
G70 / G100 / G130 / G150
wc_bo5100027027_02_FM10T
9
9.9 Emergency Stop Switch ................................................................... 107
9.10 Engine and Generator Monitoring .................................................... 108
10 Working with Deep Sea Controller: DSE 7310 109
10.1 Introduction ....................................................................................... 109
10.2 Navigating the Menus ....................................................................... 110
10.3 Adjusting Screen Contrast ................................................................ 112
10.4 How to Reset the Maintenance Timer .............................................. 113
11 How to Connect Loads—480V 114
11.1 Lug Terminal Connection Diagrams ................................................. 114
11.2 Best Practices for Balancing Loads .................................................. 115
11.3 Connecting 480V, 3-Phase and Single-Phase Loads ...................... 118
11.4 Connecting a 240V 3Ø Load and a 240V 1Ø Load .......................... 119
11.5 Connecting 240V and 120V Single-Phase Loads ............................ 120
11.6 Connecting a 208V 3Ø Load and Multiple 120V 1Ø Loads .............. 121
11.7 Connecting a 220–240V 3Ø Load and Multiple 127–133V
1Ø Loads .......................................................................................... 122
12 Using Remote Start Capabilities 123
12.1 Remote Run Terminal Block ............................................................ 123
12.2 Remote Transfer Switch ................................................................... 124
12.3 Preparing for Automatic/Remote Start-Up—Basler .......................... 125
12.4 Preparing for Automatic/Remote Start-Up—Deep Sea .................... 126
13 Diagnostic Trouble Codes (DTC) 128
13.1 Accessing DTCs with the Basler Controller ...................................... 128
13.2 Accessing Engine DTCs using the Deep Sea Controller ................. 129
13.3 List of Engine Diagnostic Trouble Codes (DTCs) ............................. 130
14 Factory-Installed Options 144
14.1 Battery Charger ................................................................................ 144
14.2 Lockable Battery Disconnect ............................................................ 145
14.3 Camlocks .......................................................................................... 146
14.4 Containment System ........................................................................ 147
14.5 Extended Run Tank (ERT) ............................................................... 147
14.6 Engine Block Heater ......................................................................... 148
Table of Contents
G70 / G100 / G130 / G150
wc_bo5100027027_02_FM10TOC.fm
10
14.7 Cold-Weather Thermostat .................................................................149
14.8 Low Coolant Shutdown .....................................................................150
14.9 Temperature-Activated Shutters .......................................................151
14.10 Positive Air Shutoff Valve ..................................................................152
14.11 Connecting an External Fuel Supply .................................................153
14.12 Lube Level Maintainer .......................................................................154
15 Machines with Aftertreatment Exhaust System 155
15.1 How the Aftertreatment Exhaust System Works ...............................155
15.2 Filling the DEF Tank ..........................................................................156
15.3 Shelf Life of Diesel Exhaust Fluid (DEF) ...........................................158
15.4 Monitoring and Control of the DEF Level ..........................................159
15.5 Monitoring DEF Quality .....................................................................160
15.6 Conditioning the Aftertreatment Exhaust System (if equipped) .........161
16 General Maintenance 162
16.1 Periodic Maintenance Schedule ........................................................162
16.2 Maintaining the Emission Control System .........................................163
16.3 Preparing for Maintenance ................................................................163
16.4 Cleaning the Machine ........................................................................163
16.5 Inspecting the Machine .....................................................................164
16.6 Maintaining the Trailer .......................................................................165
16.7 Checking and Draining the Containment System (if equipped) .........166
16.8 Checking the Exhaust System ..........................................................167
16.9 Maintaining the Battery ......................................................................168
16.10 Cleaning the Diesel Particulate Filter (DPF) (if equipped) .................169
16.11 Filling the Radiator ............................................................................170
16.12 Replacing the Aftertreatment DEF Dosing Unit Filter (if equipped) ...172
16.13 Storage ..............................................................................................174
16.14 Machine Disposal and Decommissioning ..........................................175
17 Engine Maintenance: T4F Cummins
QSB5-G10 / QSB5-G11 / QSB5-G12 176
18 Troubleshooting 180
Table of Contents
G70 / G100 / G130 / G150
wc_bo5100027027_02_FM10T
11
19 Technical Data 181
19.1 Engine: G70 / G100 .......................................................................... 181
19.2 Engine: G130 / G150 ........................................................................ 182
19.3 Machine ............................................................................................ 183
19.4 Trailer and Skid ................................................................................ 184
19.5 Dimensions ....................................................................................... 185
Tire Safety Information 187
20 User’s Information for Transport Canada Fuel Tank 199
21 Emission Control Systems Information and Warranty—Diesel 202
21.1 Emission Control System Background Information .......................... 202
21.2 Limited Defect Warranty for Exhaust Emission Control System ....... 203
21.3 Limited Defect Warranty for Wacker Neuson Emission Control
Systems ............................................................................................ 203
22 General Machine Schematics 207
22.1 Fuses ................................................................................................ 207
22.2 Trailer Wiring .................................................................................... 208
22.3 Trailer Wiring Components ............................................................... 209
23 Schematics, Machines with Basler Controller 210
23.1 AC Schematic: G70 / G100 / G130 / G150 ...................................... 210
23.2 AC Schematic Components: G70 / G100 / G130 / G150 ................. 211
23.3 DC Schematic: G70 / G100 / G130 / G150 ...................................... 212
23.4 DC Schematic Components: G70 / G100 / G130 / G150 ................. 213
23.5 Electrical Schematic Section A ......................................................... 214
23.6 Electrical Schematic Components .................................................... 215
23.7 Electrical Schematic Section B ......................................................... 216
23.8 Electrical Schematic Components .................................................... 217
23.9 Electrical Schematic Section C ........................................................ 218
23.10 Electrical Schematic Components .................................................... 219
23.11 Cummins Engine Relays and Fuses ................................................ 220
23.12 Cummins Engine Relays and Fuses ................................................ 221
Table of Contents
G70 / G100 / G130 / G150
wc_bo5100027027_02_FM10TOC.fm
12
24 Schematics, Machines with Deep Sea Controller 222
24.1 AC Schematic: G70 / G100 / G130 / G150 .......................................222
24.2 Electrical Schematic Components: G70 / G100 / G130 / G150 ........223
24.3 DC Schematic: G70 / G100 / G130 / G150 .......................................224
24.4 DC Schematic Components: G70 / G100 / G130 / G150 ..................225
24.5 Electrical Schematic Section A ..........................................................226
24.6 Electrical Schematic Components .....................................................227
24.7 Electrical Schematic Section B ..........................................................228
24.8 Electrical Schematic Components .....................................................229
24.9 Electrical Schematic Section C .........................................................230
24.10 Electrical Schematic Components .....................................................231
24.11 Cummins Engine Relays and Fuses .................................................232
24.12 Cummins Engine Relays and Fuses .................................................233
wc_tx003567gb_FM10.fm
13
Mobile Generator Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
â–º Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
â–º To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
â–º To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
â–º To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_tx003567gb_FM10.fm
14
Safety Information Mobile Generator
1.2 Machine Description and Intended Use
Machine
description
This machine is a mobile electric power source. The Wacker Neuson Mobile
Generator consists of a trailer-mounted cabinet containing an electric alternator, a
fuel tank, and a diesel engine. A control panel, receptacles, and connection lugs
are provided on the side of the cabinet. As the engine runs, the generator converts
mechanical energy into electric power. The operator connects loads to the electric
power receptacles and connection lugs.
Intended use
This machine is intended for the purpose of supplying electrical power to
connected loads. Refer to the product specifications for the output voltage and
frequency of this generator, and for the maximum output power limit of this
generator.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty.
The following are some examples of misuse:
â–  Connecting a load that has voltage and frequency requirements that are
incompatible with the generator output
â–  Overloading the generator with a load that draws excessive power during either
continuous running or start-up
â–  Operating the generator in a manner that is inconsistent with all federal, state
and local codes and regulations
â–  Using the machine as a ladder, support, or work surface
â–  Using the machine to carry or transport passengers or equipment
â–  Using the machine to tow other machines
â–  Operating the machine outside of factory specifications
â–  Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operator’s Manual
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
â–  Heat, noise, exhaust, and carbon monoxide from the engine
â–  Fire hazards from improper refueling techniques
â–  Fuel and its fumes
â–  Electric shock and arc flash
â–  Personal injury from improper lifting the trailer tongue
â–  Typical hazards related to towing a trailer on roads and highways
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.
wc_tx003567gb_FM10.fm
15
Mobile Generator Safety Information
1.3 Safety Guidelines for Operating the Machine
Operator
training
Before operating the machine:
â–  Read and understand the operating instructions contained in all manuals
delivered with the machine.
â–  Familiarize yourself with the location and proper use of all controls and safety
devices.
â–  Contact Wacker Neuson for additional training if necessary.
When operating this machine:
â–  Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
â–  Have received instruction on how to properly use the machine
â–  Are familiar with required safety devices
The machine must not be accessed or operated by:
â–  Children
â–  People impaired by alcohol, drugs or prescription drugs
Application
area
Be aware of the application area.
â–  Keep unauthorized personnel, children, and pets away from the machine.
â–  Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
â–  Identify whether special hazards exist in the application area, such as toxic
gases or unstable ground conditions, and take appropriate action to eliminate
the special hazards before using the machine.
Be aware of the application area.
â–  Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
Safety
devices,
controls, and
attachments
Only operate the machine when:
â–  All safety devices and guards are in place and in working order.
â–  All controls operate correctly.
■ The machine is set up correctly according to the instructions in the Operator’s
Manual.
â–  The machine is clean.
■ The machine’s labels are legible.
To ensure safe operation of the machine:
â–  Do not operate the machine if any safety devices or guards are missing or
inoperative.
â–  Do not modify or defeat the safety devices.
â–  Only use accessories or attachments that are approved by Wacker Neuson.
wc_tx003567gb_FM10.fm
16
Safety Information Mobile Generator
Safe
operating
practices
When operating this machine:
■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
When operating this machine:
â–  Do not operate a machine in need of repair.
â–  Do not consume the operating fluids used in this machine. Depending on your
machine model, these operating fluids may include water, wetting agents, fuel
(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic fluid,
heat transfer fluid (propylene glycol with additives), battery acid, or grease.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while operating this
machine:
â–  Close-fitting work clothes that do not hinder movement
â–  Safety glasses with side shields
â–  Hearing protection
â–  Safety-toed footwear
After use
â–  Stop the engine when the machine is not being operated.
â–  Close the fuel valve on engines equipped with one when the machine is not
being operated.
â–  Ensure that the machine will not tip over, roll, slide, or fall when not being
operated.
â–  Store the machine properly when it is not being used. The machine should be
stored in a clean location out of the reach of children.
wc_tx003567gb_FM10.fm
17
Mobile Generator Safety Information
1.4 Service Safety
Service
training
Before servicing or maintaining the machine:
â–  Read and understand the instructions contained in all manuals delivered with
the machine.
â–  Familiarize yourself with the location and proper use of all controls and
protective devices.
â–  Only trained personnel shall troubleshoot or repair problems occurring with the
machine.
â–  Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
â–  Do not allow untrained or improperly trained people to service or maintain the
machine. Personnel servicing or maintaining the machine must be familiar with
the associated potential risks and hazards.
â–  Maintenance items that can be performed by the operator are listed in this
manual. Other repairs should be performed by a qualified technician. Repairs
can be hazardous if not performed correctly. Contact your Wacker Neuson
dealer service department for additional information or for repairs to your
machine.
Precautions
When servicing or maintaining the machine:
â–  Read and understand the service procedures before performing any service to
the machine.
â–  All adjustments and repairs must be completed before operating the machine.
Do not operate the machine with a known problem or deficiency.
â–  All repairs and adjustments shall be completed by a qualified technician.
â–  Turn off the machine before performing maintenance or making repairs.
■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
â–  Re-install the safety devices and guards after repair and maintenance
procedures are complete.
Machine
modifications
When servicing or maintaining the machine:
â–  Use only accessories/attachments that are approved by Wacker Neuson.
â–  Do not defeat safety devices.
â–  Do not modify the machine without the express written approval of Wacker
Neuson.
Replacing
parts and
labels
â–  Replace worn or damaged components.
â–  Replace all missing and hard-to-read labels.
â–  When replacing electrical components, use components that are identical in
rating and performance to the original components.
â–  When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all types of
specifications, such as physical dimensions, type, strength, and material.
wc_tx003567gb_FM10.fm
18
Safety Information Mobile Generator
Cleaning
When cleaning and servicing the machine:
â–  Keep machine clean and free of debris such as leaves, paper, cartons, etc.
â–  Keep labels legible.
â–  Clean with soapy water only.
When cleaning the machine:
â–  Do not clean the machine while it is running.
â–  Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while servicing or
maintaining this machine:
â–  Close-fitting work clothes that do not hinder movement
â–  Safety glasses with side shields
â–  Hearing protection
â–  Safety-toed footwear
In addition, before servicing or maintaining the machine:
â–  Tie back long hair.
â–  Remove all jewelry (including rings).
Electrical
service safety
â–  Make sure clothing and shoes are dry, stand on a dry wooden platform or rubber
insulating mat, and use tools with insulated handles when servicing the
machine.
â–  Do not allow water to accumulate around the base of the machine. If water is
present, move the machine and allow the machine to dry before servicing.
â–  Do not pressure wash the control panel, generator end, or any other electrical
components when cleaning the machine.
Cooling
system safety
â–  Do not attempt to open the radiator cap while the unit is running or before the
engine has cooled down. Severe burns may result!
â–  Engine coolant is toxic to humans and animals. Clean up spills and dispose of
waste engine coolant in accordance with local environmental regulations.
wc_tx003567gb_FM10.fm
19
Mobile Generator Safety Information
1.5 Operator Safety while Using Internal Combustion Engines
Operating
safety
When running the engine:
â–  Keep the area around the exhaust pipe free of flammable materials.
â–  Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine. Do not run the machine if fuel leaks are present or the fuel lines are
loose.
When running the engine:
â–  Do not smoke while operating the machine.
â–  Do not run the engine near sparks or open flames.
â–  Do not touch the engine or muffler while the engine is running or immediately
after it has been turned off.
â–  Do not operate a machine when its fuel cap is loose or missing.
â–  Do not start the engine if fuel has spilled or a fuel odor is present. Move the
machine away from the spill and wipe the machine dry before starting.
Refueling
safety
When refueling the engine:
â–  Clean up any spilled fuel immediately.
â–  Refill the fuel tank in a well-ventilated area.
â–  Re-install the fuel tank cap after refueling.
â–  Use suitable tools for refueling (for example, a fuel hose or funnel).
When refueling the engine:
â–  Do not smoke.
â–  Do not refuel a hot or running engine.
â–  Do not refuel the engine near sparks or open flames.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
► Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Exhaust gas from the engine contains carbon monoxide, a deadly poison.
Exposure to carbon monoxide can kill you in minutes.
â–º NEVER operate the machine inside an enclosed area, such as a tunnel, unless
adequate ventilation is provided through items such as exhaust fans or hoses.
wc_tx003567gb_FM10.fm
20
Safety Information Mobile Generator
1.6 Safety Guidelines for Mobile Generators
Installing as
backup power
Special hazards exist when installing this machine as a backup power supply.
Improper connection of generator to a building’s electrical system can allow
electrical current from the generator to backfeed into utility lines. This may result in
electrocution of utility workers, fire, or explosion.
If connected to a building’s electrical system, the generator must meet the power,
voltage, and frequency requirements of the equipment in the building. Differences
in power, voltage, and frequency requirements may exist and improper connection
may lead to equipment damage, fire, and personal injury or death.
DANGER
Carbon monoxide. Using a generator indoors CAN KILL YOU IN MINUTES.
Generator exhaust contains carbon monoxide (CO). This is a poison you cannot
see or smell. If you can smell the generator exhaust, you are breathing CO. Even if
you cannot smell the exhaust, you could be breathing CO.
â–º NEVER use a generator inside homes, garages, crawlspaces, or other partly
enclosed areas. Deadly levels of carbon monoxide can build up in these areas.
Using a fan or opening windows and doors does NOT supply enough fresh air.
â–º ONLY use a generator outside and far away from windows, doors, and vents.
These openings can pull in generator exhaust.
â–º Even when you use a generator correctly, CO may leak into the home. ALWAYS
use a battery-powered or battery-backup CO alarm in the home.
â–º If you start to feel sick, dizzy, or weak after the generator has been running,
move to fresh air RIGHT AWAY. See a doctor. You could have carbon monoxide
poisoning.
WARNING
Electrocution hazard. Machines that generate electric power present special
hazards while the engine is running. These include the risk of electrocution or
severe electrical shock.
► Read and follow the instructions in this Operator’s Manual.
WARNING
Backfeed from the generator into the public power distribution system can cause
serious injury or death to utility workers!
► Connections to a building’s electrical system must be made by a qualified
electrician and comply with all applicable laws and electrical codes.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416
  • Page 417 417
  • Page 418 418
  • Page 419 419
  • Page 420 420
  • Page 421 421
  • Page 422 422
  • Page 423 423
  • Page 424 424
  • Page 425 425
  • Page 426 426
  • Page 427 427
  • Page 428 428
  • Page 429 429
  • Page 430 430
  • Page 431 431
  • Page 432 432
  • Page 433 433
  • Page 434 434
  • Page 435 435
  • Page 436 436
  • Page 437 437
  • Page 438 438
  • Page 439 439
  • Page 440 440
  • Page 441 441
  • Page 442 442
  • Page 443 443
  • Page 444 444
  • Page 445 445
  • Page 446 446
  • Page 447 447
  • Page 448 448
  • Page 449 449
  • Page 450 450
  • Page 451 451
  • Page 452 452
  • Page 453 453
  • Page 454 454
  • Page 455 455
  • Page 456 456
  • Page 457 457
  • Page 458 458
  • Page 459 459
  • Page 460 460
  • Page 461 461
  • Page 462 462
  • Page 463 463
  • Page 464 464
  • Page 465 465
  • Page 466 466
  • Page 467 467
  • Page 468 468
  • Page 469 469
  • Page 470 470
  • Page 471 471
  • Page 472 472
  • Page 473 473
  • Page 474 474
  • Page 475 475
  • Page 476 476
  • Page 477 477
  • Page 478 478
  • Page 479 479
  • Page 480 480
  • Page 481 481
  • Page 482 482
  • Page 483 483
  • Page 484 484
  • Page 485 485
  • Page 486 486
  • Page 487 487
  • Page 488 488
  • Page 489 489
  • Page 490 490
  • Page 491 491
  • Page 492 492
  • Page 493 493
  • Page 494 494
  • Page 495 495
  • Page 496 496

Wacker Neuson G150 User manual

Category
Power generators
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages