Best IC34E100SB Installation guide

In USA - BEST Hartford, Wisconsin

In CANADA - BEST Drummondville, QC, Canada

Model IC34

ENGLISH........................................3

FRANÇAIS...................................23

ESPAÑOL.....................................45

REGISTER YOUR PRODUCT ONLINE AT : www.BestRangeHoods.com/register

For additional Information visit www.BestRangeHoods.com

- 3 -

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the

manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel to

prevent power from being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all

applicable codes and standards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney)

of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s

guidelines and safety standards such as those published by the National Fire Protection Associa-

tion (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any separate solid-state speed control device.

8. To reduce the risk of fire, use only steel ductwork.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk

of electrical shock by providing an escape wire for the electric current.

WARNING - Improper grounding can result in a risk of electric shock.

Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt

exists as to whether the appliance is properly grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette,

Cherries Jubilee, Peppercorn Beef Flambe’).

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface element.

!

INTENDED FOR DOMESTIC COOKING ONLY

!

- 4 -

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you already know how to operate it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

!

CAUTION

1. For indoor use only.

2. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust

air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. Take care when using cleaning agents or detergents.

4. Avoid using food products that produce flames under the Range Hood.

5. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and

vapors.

6. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray,

construction dust, etc. off power unit.

7. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes

overheated. The motor will restart when it cools down. If the motor continues to shut off and restart,

have the hood serviced.

8. For best capture of cooking impurities, the bottom of the hood should be a minimum of 24" and a

maximum of 36" above the cooking surface.

9. Two installers are recommended because of the large size and weight of this hood.

10. This product is equipped with a thermostat which may start blower automatically. To reduce the

risk of injury and to prevent power from being switched on accidentally, switch power off at service

panel and lock or tag service panel.

11. Please read specification label on product for further information and requirements.

12. EXTERNAL BLOWER MODELS ONLY: To reduce risk of fire and electric shock, install this range

hood only with Best Exterior Blower Models EB6, EB9, EB12 or EB15 or Best In-Line Blower

Models ILB3, ILB6, ILB9 or ILB11. Other blowers cannot be substituited. (Blower sold separately).

13. This hood is not designed to be used as a shelf.

- 5 -

LED LAMPS

The hood is provided with LED lamps wich require no maintenance.

CLEANING AND MAINTENANCE

Proper maintenance of the Range Hood will assure proper performance of the unit.

Motor

The motor is permanently lubricated and never needs oiling. If the motor bearings make

excessive or unusual noise, replace the motor with the exact service motor. The impeller

should also be replaced.

Grease Filter

The grease filters should be cleaned frequently. Use a warm detergent solution. Grease

filter are dishwasher safe.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration

of the filter may occur if using phosphate detergents, or as a result of local water

conditions - but this will not affect filter performance. This discoloration is not covered by

the warranty. See “INSTALL FILTERS” section for removal and installation instructions.

Non-ducted Recirculation Filter

The non-ducted recirculation filter should be changed every 6 months. Replace more

often if your cooking style generates extra grease, such as frying and wok cooking. See

“INSTALL FILTERS” section for removal and installation instructions.

Stainless Steel Cleaning

DO:

• Regularly wash with clean cloth or rag

soaked with warm water and mild soap or

liquid dish detergent.

• Always clean in the direction of original

polish lines.

• Always rinse well with clear water (2 or 3

times) after cleaning. Wipe dry completely.

• You may also use a specialized

household stainless steel cleaner.

DON’T:

• Use any steel or stainless steel wool or

any other scrapers to remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction

residues reach the hood. During

construction/renovation, cover the range

hood to make sure no dust sticks to the

stainless steel surface.

Avoid: When choosing a detergent

• Any cleaners that contain bleach will attack stainless steel

• Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.

• Any combustible products used for cleaning such as acetone, alcohol, ether, benzol,

etc., are highly explosive and should never be used close to a range.

- 6 -

OPERATION

The hood is operated using the (5) push buttons located on the front edge of the hood. The

Light On/Off buttons turn the lights on and off.

The Blower Off / - button decreases the blower speed each time pressed. Depress and

hold the button for 2 seconds to turn the blower off.

The Blower On /+ button turns the blower on and increases the blower speed each time

pressed. There are four different speed settings: Low, Medium-Low, Medium-High and High.

The Blower LED Indicators illuminate to indicate the selected blower speed.

The Delay button activates the delay-off feature. When the blower in on and the button is

pushed, the blower will continue to operate at the current speed setting for 10-minutes

before automatically turning itself off. The LED (on the right) flashes during operation.

The LED (on the right) is also used as a filter clean reminder. It will flash after 30 hours of

operation - indicating the need to clean the filters.

The Filter Clean Reset button is used to reset the 30-hour filter timer. After filters are

cleaned or replaced, press button once to reset the filter clean alarm.

HEAT SENTRY™

Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a device that

will turn on or speed up the blower if it senses excessive heat above the cooking surface.

1) If blower is OFF - it turns blower ON to HIGH speed.

2) If blower is ON at a lower speed setting - it turns blower up to HIGH speed.

When the temperature level drops to normal, the blower will return to its original setting.

WARNING

The HEAT SENTRY thermostat can start the blower even if the hood is turned OFF.

When this occurs, it is impossible to turn the blower OFF with its switch. If you must

stop the blower, do it from the main electrical panel.

REMOTE CONTROL:

An optional ACR Series remote control (purchase separately) can be used to operated the

range hood.

Controls (Fig.1)

- 7 -

PREPARE THE HOOD

Unpack hood and check contents.

You should receive:

1 - Hood

1 - Decorative Flues

1 - Support Frame

1 - Parts Bag (B080811002) containing:

32 - Mounting Screws (3,9 x 9,5mm Pan Head)

6 - Mounting Lag Screws (6 x 60mm)

10 - Lock Washers ø 4,3

1 - Damper Kit

4 - Mounting Screws (3,9 x 9,5mm Pan Head)

1 - Installation Instructions

DAMPER KIT

DECORATIVE

FLUES

32 MOUNTING

SCREWS (3,9x9,5mm

Pan Head)

6 MOUNTING LAG

SCREWS (6x60mm)

FIG. 3

10 LOCK WASHERS Ø 4.3

SUPPORT

FRAME

4 MOUNTING

SCREWS (3,9x9,5mm

Pan Head)

- 8 -

EXTERIOR AND IN-LINE BLOWER SELECTION IC34E Series

CAUTION: To reduce risk of fire and electric shock, install this range hood only with Best

Exterior Blower Models EB6, EB9, EB12 or EB15, and Best In-Line Blower Models ILB3, ILB6,

ILB9 or ILB11. Other blowers cannot be substituited.

The blower must be UL listed for Canadian and U.S. use, and evaluated for use with solid state

speed control, rated 120V, 60 Hz, 6.0 A max.

INSTALL THE DUCTWORK IC34E Series

NOTE: To reduce the risk of fire, use only metal ductwork.

1. Choose the location where the Exterior Blower or In-Line Blower will be mounted. See

illustrations below for mounting location suggestions and restrictions.

2. A straight, short duct run will allow the hood to perform most efficiently.

3. Long duct runs, elbows and transitions will reduce the performance of the hood. Use as

few of them as possible. Larger ducting may be required for best performance with long

duct runs.

4. After the Exterior or In-Line Blower has been installed, connect round metal ductwork

and work back towards the hood location. Use duct tape to seal joints between ductwork

sections.

10”ROUND

DUCT

24” TO 36” ABOVE

COOKING SURFACE

DECORATIVE

FLUE

10” ROUND

DUCT

EXTERIOR

BLOWER

HOOD

OK

SUGGESTED MOUNTING LOCATIONS

EXTERIOR BLOWER

CAUTION: MAY NOT FIT

UNDER EAVES OF SINGLE

STORY HOMES

FIG. 4

- 9 -

IN-LINE BLOWER

FIG. 5

INSTALL THE DUCTWORK

IC34IQ Series

WARNING: To reduce the risk of fire, use

only metal ductwork.

1. Decide where the ductwork will run

between the hood and the outside.

2. A straight, short duct run will allow the hood

to perform most efficiently.

3. Long duct runs, elbows, and transitions will

reduce the performance of the hood. Use

as few of them as possible.

4. Install a roof or wall cap. Connect 8" round

metal ductwork to cap and work back

towards hood location. Use duct tape to

seal the joints between ductwork sections.

ROOF CAP

8” ROUND

ELBOW

24” TO 36” ABOVE

COOKING SURFACE

8” ROUND

DUCT

DECORATIVE

FLUE

HOOD

- 10 -

Ceiling

Height

Hood Distance Above 36” High Cook Top (in.)

8 Feet

23

3

/8”

10 Feet

(see note c)

11 Feet

(see note c)

9 Feet

22

3

/8”21

3

/8”- - - - - - - - - -

--34

3

/8”33

3

/8”32

3

/8”31

3

/8”30

3

/8”29

3

/8”28

3

/8”27

3

/8”26

3

/8”25

3

/8”24

3

/8”

47

3

/8”46

3

/8”45

3

/8”44

3

/8”43

3

/8”42

3

/8”41

3

/8”40

3

/8”39

3

/8”38

3

/8”37

3

/8”36

3

/8”-

-58

3

/8”57

3

/8”56

3

/8”55

3

/8”54

3

/8”53

3

/8”52

3

/8”51

3

/8”50

3

/8”49

3

/8”48

3

/8”47

3

/8”

24

25 26 28 29 30 31 32 33 34 35 36 27

Assembled Support Frame Height (in.)

INSTALL SUPPORT SYSTEM

1. At hood location, install 2 x 4 or larger

cross framing between ceiling joists

using dimensions shown.

2. Finish the ceiling surface. Be sure to mark

the location of the ceiling joists and cross

framing (Fig. 6).

3. Mount the four 6x60mm screws to ceiling

in the location shown in figure 7. Allow 1/

4” clearance between screw head and

ceiling (screws will be tightened later).

Make sure the screws are driven into the

center of joists and framing for maximum

strength.

TOP VIEW OF SUPPORT FRAME

10

3

/16” (260mm)

11

7

/16”

(290mm)

CEILING

JOISTS

CROSS FRAMING

10

3

/16”

DRYWALL

==

11” (280mm)

FIG. 6

FIG. 7

Notes:

a. “-” = Mounting height is not possible.

b. Minimum hood distance above cook top must not be less than 24”. A maximum of 36”

above cook top is highly recommended for best capture of cooking impurities.

Distances over 36” are at the installer and the users discretion; and if ceiling height

and flue length permit.

c. Requires optional 10 / 11’ flue extension, ducted model AEIC345SB or non-ducted

model AEIC345SBN.

HOOD MOUNTING TABLE

- 11 -

INSTALL THE HOOD

DUCTED AND NON-DUCTED INSTALLATION

1. Remove the electrical system box from

chimney frame by removing (2) 3.9 x 9.5

mm screws (Fig. 8).

2. Attach electrical system box to frame using

(2) 3.9 x 9.5 mm screws removed in Step

1 and (2) 3.9 x 9.5 mm screws and (2) lock

washers from hardware bag (Fig.9)

3. Fix the damper kit onto the hood using 4

screws (3.9x9.5mm) located in the

Damper Package (Fig.10).

4. Adjust the overall height using the chart

shown on page 10 of the support frame.

Loosen and re-tighten the 4 screws in the

height adjustment slots as necessary.

Insert 12 screws (3.9x9.5mm) located in

the Hardware Package (Fig.11) make

sure this a 4” min. overlap between the

upper and lower support legs.

SUPPORT

FRAME

MOUNTING

SCREWS

(6x60mm)

HEIGHT ADJUSTMENT

SLOTS

FIG.11

MOUNTING

SCREWS

3,9x9,5mm

FIG.9

FIG.8

FIG.10

MOUNTING SCREWS

3,9x9,5mm

MOUNTING SCREWS 3,9x9,5mm

- 12 -

5. Adjust the overall height of the support

frame. Loosen and re-tighten the 4 screws

in the height adjustment slots as

necessary. Insert 16 screws (3.9x9.5mm),

and 8 lock washers (D.4.3) located in the

Hardware Package (Fig. 12).

CONNECT DECORATIVE FLUE

DUCTED INSTALLATION ONLY

Note: Rooms with 10 or 11 foot ceilings

require flue extension model AEIC34SB,

available from your local dealer. Discard

the upper flue supplied with the range

hood and replace it with the longer flue

extension.

1. Insert the upper flue and lower flue in the

support frame (Fig.13).

2. Mount the hood to the ceiling using the (4)

previously installed 6x60mm screws.

Tighten these screws. Install (2) additional

6x60mm screws as shown in the

illustration. Make sure all (6) screws are

secure.

3. Use 8" round metal duct to connect the

duct collar on the hood to the ductwork

above (Fig.14).

4. Use duct tape to make all joints secure and

air tight.

FIG.13

FIG.12

INSTALL (16) 3.9 x 9.5 mm SCREWS &

LOCK WASHERS ON (8) SCREWS

FIG.14

10-INCH DIA.

METAL DUCT

- 13 -

NON-DUCTED INSTALLATION ONLY

Note:

a. Purchase Model ANKWC45 Non-ducted

Recirculation Kit from your local dealer.

b. Rooms with 10 or 11 foot ceilings require

flue extension model AEIC34SBN,

available from your local dealer. Discard

the upper flue supplied with the range hood

and replace it with the longer flue extension.

1. Install discharge collar supplied with the

range hood (Fig.15).

2. Attach the 6”-to-8” adapter to blower

discharge and tape joint with aluminum

duct tape (Fig.15).

3. Insert the plenum in the upper support

frame. Make sure that the letter F is

positioned at the front of the support frame

(Fig.16).

4. Install the plenum to the upper decorative

flue using (2) 3.9 x 9.5 mm screws

provided as shown (Fig.17).

5. Attach 6-inch expandable ducting to the

plenum and tape joint with aluminum duct

tape (Fig.18).

MOUNTING SCREWS

(3.9 x 9.5 mm Flat Head)

FIG. 15

FIG. 18

DUCT

CONNECTOR

FIG. 17

FIG. 16

FRONT

EXPANDABLE

DUCT

- 14 -

WIRING (IC34IQ)

Note: This range hood must be properly

grounded. The unit should be installed by a

qualified electrician in accordance with all

applicable national and local electrical

codes.

1. Remove the wiring box cover. Remove a

knockout from the wiring box (Fig.19).

2. Secure the conduit to the wiring box

through a conduit connector.

3. Make electrical connections. Connect white

to white, black to black and green to green.

4. Replace wiring box cover and screws. Make

sure that wires are not pinched between

cover and box.

ADDITIONAL EXTERNAL

BLOWER WIRING (IC34E)

1. Run 2-wire plus ground power cable from

the exterior blower to the hood’s wiring

box marked “motor connection” (Fig.20).

2. Remove the cover from the wiring box and

remove one knockout.

3. Feed 6” of cable through the knockout

opening and secure the cable to the wiring

box with an appropriate connector.

4. Make electrical connections at the hood.

Connect white-to-white, red-to-black and

green-to-ground.

5. Replace the wiring box cover and screws.

Make sure wires are not pinched between

the cover and box.

Exterior blower connection:

1. Make electrical connections at the exterior

blower (see instructions provided with the

exterior blower).

CONNECT DECORATIVE FLUE

1. Attach the upper flue to the upper support

frame with the mounting screws 3.9x9.5

mm (Fig.21).

2. Lower the lower flue in place.

WIRING BOX

COVER

FIG.19

EXTERIOR BLOWER

BLOWER CONNECTION AT HOOD

CONNECT:

WHITE-TO-WHITE,

RED-TO-BLACK,

GREEN-TO-GROUND.

BOX MARKED

“MOTOR

CONNECTION”

FIG.20

FIG. 21

MOUNTING SCREWS

(3.9 x 9.5 mm Flat Head)

- 15 -

FIG. 22

FIG. 23

INSTALL FILTERS

DUCTED AND NON-DUCTED HOODS

NOTE: prior to use, remove protective film

from the filter frame.

1. To remove the GREASE filter, push in

latch tab to disengage the filter from the

hood. Tilt the filter downward and

remove (Fig.22).

2. To install the GREASE filter, align rear filter

tabs with slots in the hood. Push latch tab

in, push filter into position and release.

Make sure the filter is securely engaged

after installation.

NON-DUCTED HOODS ONLY

1. To remove the CHARCOAL filter, grip and

push filter tab toward rear of hood. Pull

the filter down to disengage the rear filter

tabs (Fig.23).

2. To install the CHARCOAL filter, align filter

in rectangular opening. Push filter against

springs in rear of hood and press into

place. Make sure the filter is securely

engaged after assembly.

3. Install GREASE filter after charcoal filter

is installed.

4. The charcoal filter replacement model is

AFCWC345.

- 16 -

CALIBRATION LIGHT

CALIBRATION

BUTTON

CALIBRATE IQ BLOWER SYSTEM

TM

INTERNAL BLOWER DUCTED UNITS ONLY

After the hood is installed and wired, engage the calibration process (our Guaranteed Performance

System Technology to ensure full-rated airflow is being delivered). Prior to calibration, ensure that all

filters, light bulbs and duct system are installed.

CALIBRATION PROCESS

Hold the calibration button for 3 seconds; calibration button will light up and stay on for up to 13 minutes.

The blower will start and begin the calibration process. When calibration is complete, one of two things

will occur:

1. The blower turns off and

calibration button light stays on = Successful calibration. Press the button

to turn off the LED. Note: The LED will also turn off if you select any blower speed on the control.

2. The blower turns off and

calibration button light blinks continuously = Too much restriction in the

ductwork is preventing the IQ Blower System™ from achieving the rated airflow. The blower is

automatically set to maximum intensity.

NOTE: Common items that cause restrictions: restricted damper flap (backdraft damper, wall cap,

roof cap), too many elbows, duct size less than 80% of hood outlet, poor transition, use of flex ducting

and/or crushed ducting.

Three options are available if your hood system has too much restriction:

1. Accept airflow as is.

a. Press the calibration button to accept airflow as is. The IQ Blower System™ is nowconfigured to

the highest possible performance. The blinking calibration light goes out. Note: The LED will also

turn off if you select any blower speed on the control.

2. Correct duct restriction, clear the original calibration data, and repeat the calibration process.

a. Correct the duct restriction.

b. Clear the original calibration data by holding calibration button for 10 seconds. The light will blink

3 times to confirm and the blower configuration will go back to default settings.

c. Repeat calibration process from the beginning.

3. Clear calibration data to reset hood to default factory setting and achieve standard high

pressure blower performance.

a. Clear calibration data and reset hood to factory default setting by holding calibration

button for 10 seconds. The light will blink 3 times to confirm and the blower configuration

will go back to default settings.

- 17 -

IC34E Programming Mode Procedure

FIG. 24

- 18 -

WARRANTY

ONE YEAR LIMITED WARRANTY FOR BEST PRODUCTS

Broan-NuTone LLC (Broan-NuTone) warrants to the original consumer purchaser of Best products that such products will be free

from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANT ABILITY

OR FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found

to be defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDESCENT

BULBS, FUSE, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does

not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence,

accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary to recom-

mended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states do not

allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

BROAN-NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE'S OPTION, SHALL BE THE PURCHASER'S

SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL,

CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion

may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty

supersedes all prior warranties.

To qualify for warranty service, you must (a) notify Broan-NuTone at the address stated below or telephone number stated below,

(b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of

requesting warranty service, you must present evidence of the original purchase date.

In USA - Best®, 926 W. State Street, Hartford, WI 53027 (800-558-1711)

In Canada - Best®, 550 Lemire Blvd., Drummondville, QC J2C 7W9 (866-737-7770)

www.BestRangeHoods.com

- 19 -

KEY NO. PART NO. DESCRIPTION

9 B08087679 Grease Filters

17 BE3351998 Light Diffuser Support

37 B02300804 Heat Sentry

67 B06102619 Wires Assembly

76 B003102891 Glass Front Trim

114 B032904990 Runner Wires

115 BE3350233 Wiring Box

116 BE3334252 Wiring Box Cover

124 B08092904 Telescopic Structure Bottom

125 B08093457 Telescopic Structure Top

130 B08092983 Glass Trim Back

202 B03292290 Wire Clamp

415 B03292596 Fairlead

439 B02320034 Grommet

474 B08093413 Led Lamp

477 BE3352074 Light Diffuser Support Back

485 B08016376 Decorative Flue Assembly

506 97019431 BLDC Driver

507 B06102584 Calibration Button Assembly

AQI B06102594 Switch Box Assembly

ARU B080810849 Duct Connector Assembly 10”

IME B06145225 Electrical Installation Assembly

CAS B06002259 Blower Assembly

* B080811002 Fitting Set

ANKIC34 B08999181 Non-Ducted Kit (Includes Key No. 58, 64, 86, 122, 503)

58 B03294170 Outlet Reduction

64 B08093447 Non-Ducted Filter Frame

86 B03292300 Outlet Flange

122 B08093496 Non-Duct Plenum

503 B02011557 Expandable Duct

AFCWC345 B08999176 Non-Duct Filter

* Not shown assembled.

SERVICE PARTS

MODEL IC34IQ

- 20 -

Page is loading ...

Best IC34E100SB Installation guide

This manual is also suitable for

Best IC34E100SB Installation guide

in other languages

Related papers

Other documents