HOTPOINT/ARISTON TCD G51 B (SK) User guide

Contents

TUMBLE DRYER

TCD G51B

First time you turn on your dryer

you must select your preferred

language see page 6

Instruction booklet

Important information, 2-3

Installation, 4

Where to put your dryer

Ventilation

Door reversal instructions

Water drain

Electrical connection

Before you start using your dryer

Dryer description, 5

To open the door

The features

Control panel

The Display, 6-8

Start and programmes, 8-11

Choosing a programme

Special programmes

Programme option modifiers

Table of programmes

The controls

Laundry, 12-13

Sorting your laundry

Wash care labels

Special clothing items

Drying times

Warnings and Suggestions, 14

General safety

Disposal

Saving energy and respecting the environment

Maintenance and Care, 15

Switching off the electricity

Cleaning the filter after each cycle

Empty the water container after each cycle

Check the drum after each cycle

Cleaning the condenser unit

Cleaning the dryer

Troubleshooting, 16

Service, 17

Spare parts

GB

English, 1

GB

1

! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and

should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the

dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.

! Read these instructions carefully; the following pages contain important information on installation and suggestions

on how the appliance works.

SV

Svenska, 18

SF

Suomi, 52

DK

Dansk, 35

NO

Norsk, 69

Important Information

2

GB

! You MUST clean the fluff filter after EVERY drying

cycle.

Fluff Filter...

! Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine.

- It will take longer to dry and as a result will use more electricity during drying.

! You MUST empty the water container after EVERY

drying cycle.

Water Container...

Priming the Water Collection System

When your dryer is new, the water container will not collect water until the system is primed... this will take 1 or 2 drying

cycles. Once primed it will collect water during every drying cycle.

STEP 1.

Open the door of your

dryer.

STEP 2.

Pull out the filter (using

the two finger grips).

STEP 3.

Clean any fluff deposits

from the filter mesh.

STEP 4.

Refit the filter - NEVER

run the dryer without the

filter in position.

For your Condenser dryer to operate efficiently, you must follow the regular maintenance schedule shown below:

STEP 1.

Pull the water container

towards you and remove

it fully from the dryer.

STEP 2.

Empty all the water

collected in the water

container.

! Failure to empty the water container will result in:

- The machine will stop heating (so the load may still be wet at the end of the drying cycle).

- The ‘Empty Water’ message will tell you that the water container is full.

STEP 3.

Refit the water container,

ensuring that it is pushed

fully back into position.

! The ‘Empty Water’

message reminds you to

empty the water container

at the start and at the

end of each programme.

GB

3

Important Information

Condenser Unit...

! You MUST clean the fluff from the condenser EVERY

month.

! Failure to clean the condenser could cause premature

failure of your dryer.

●

Check that:

- The positioning arrows are pointing upwards.

- The 3 clips are re-secured back into their ‘lock’ position.

STEP 3.

Flush the condenser, from

the rear with water, to

remove any fluff deposits.

STEP 4.

Refit the condenser unit

- ensure that the unit is

pushed in fully, all 3 clips

are re-secured and the

positiong arrows on the

front of the condenser are

pointing upwards.

Rotate 3 clips

STEP 1.

Open the condenser cover

- hold the handle and

pull towards you.

STEP 2.

Remove the condenser by

rotating the 3 clips then

pulling the condenser

towards you.

(There may be some water

in the tubes, this is normal).

4

GB

Installation

Where to put your dryer

●

Place your dryer at a distance from gas ranges,

stoves, heaters, or cook tops because flames can

damage the appliance.

●

If you are going to install

the appliance under a work

counter, be sure to leave a

10mm space between the

top and any other objects

on or above the machine and

a 15mm space between the

sides and lateral furnishings

or walls. This is to ensure

proper air circulation. Make sure that the back vents

are not obstructed.

Ventilation

When the dryer is in use, there has to be adequate

ventilation. Make sure you put your dryer in an

environment that is not damp and has proper air

circulation throughout. Airflow around the dryer is

essential to condense the water produced during the

washing, the dryer will not operate efficiently in an

enclosed space or cupboard.

! We do not recommend that the dryer is installed in a

cupboard but the dryer must never be installed

behind a lockable door, a sliding door or a door with a

hinge on the opposite side to that of the dryer door.

! If using the dryer in a small or cold room some

condensation could be experienced.

Door Reversal Instructions

The door of your dryer is reversible and can easily be

changed. Exchange diagonally hinge brackets and

blanking screws. Exchange door latch and catch with

their opposite blanking plates (see diagram above).

Door catch

Door latch

Hinge

Water drain

If your dryer is installed next to a drain the water can be

plumbed into this drain. This does away with the need to

empty the water container. If the dryer is stacked onto or

installed next to a washing machine it can share the same

drain. The height of the drain must be less than 3' (1m)

from the bottom of the dryer.

Remove the existing clip and hose

from position shown (see diagram).

Fit a suitable length of hose to the

new location shown (see diagram)

and refit clip.

! Make sure that the hose is not squashed or kinked when

the dryer is in its final location.

Electrical connections

Make sure of the following before you insert the plug

into the the electrical socket:

●

The socket must be grounded.

●

The socket must be able to sustain the machines

maximum power, which is indicated on the rating

label (see Dryer Description).

●

Power voltage must be within the values indicated

on the rating label (see Dryer Description).

●

The socket must be compatible with the dryers plug.

Should this not be the case, replace the plug or the

socket.

! The dryer must not be installed outdoors, even if the

space is sheltered. It can be very dangerous if it is

exposed to rain or storms.

! Once installed, the dryers electrical wire and plug

must be within easy reach.

! Do not use extension cords.

! The power cord must not be bent or squashed.

! The power cord supplied should be checked

periodically and replaced by a cord specially prepared

for this dryer and fitted only by authorised technicians

(see Service). New or longer power cords are supplied

at an extra charge by authorised dealers.

! The manufacturer denies any responsibility should any

of these rules not be followed.

! If in doubt about any of the above consult a qualified

electrician.

Before you start using your dryer

Once you have installed your dryer and before you

use it, clean the inside of the drum to remove any dust

that could have accumulated during transport.

Minimum gap 10mm

Minimum gaps

15mm

Remove clip and hose

from here...

...fit new hose and refit

clip here.

GB

5

Dryer Description

Control panel

PROGRAMME

Selection Buttons

Display Unit

START/PAUSE

Button & Light

CHILD LOCK

Button

ON/OFF

Button

OPTION

Buttons

To open the door The features

Water container

Air intake

grille

Rating plate

Filter

Model &

Serial

numbers

Condenser cover handle

(Pull to open)

Condenser cover

Press and release the front

panel in position shown

Condenser Unit

(cover open)

The ON/OFF button/light : If the dryer is running

and this button is pressed, the dryer is turned off.

Press again, the dryer restarts.

The PROGRAMME selection buttons set the programme:

press the button corresponding to the programme you

want to select (see Start and Programmes).

The OPTION buttons/indicators: these buttons select

available options for your selected programme (see

The Controls). The indicators on the display unit next

to the buttons light to show that the option has been

selected.

The START/PAUSE button/light starts a selected

programme. When you press this button there will be

one beep and the display will show PAUSED . When

a programme is running, holding this button in pauses

the programme and stops the dryer.

The light is green when the programme is running,

flashing amber if the programme has been paused or

flashing green if on standby waiting to start a programme

(see Start and Programmes).

The Display Unit gives warnings and information

about the programme (see next page).

The CHILD LOCK button/icon : Press and hold this

button after selecting your programme and any options,

this prevents the programme settings from being

changed, the display will briefly show LOCKED .

When the icon is lit, the other buttons and the

programme knob are disabled. Hold the button to

cancel and the icon will go out, the display will briefly

show UNLOCKED .

6

GB

The Display

Selecting your language

Understanding the display

Programme selection and display

The selected programme is shown on the first line of the display when you select the corresponding button, this

message is shown while the programme is running.

When you select the memory button the Display will show your selected programme with ‘M’ before its name.

ie. M COTTON HIGH HEAT (see Start and Programmes).

Dryness levels

During programme selection for an automatic programme that has different dryness levels available (see

Programmes Table).

The second line of the display shows the dryness level you require, for each press of the Dryness Level button the next

option from the list below is selected and displayed.

COTTON HIGH HEAT

COTTON LOW HEAT

SYNTHETICS

BED & BATH

EASY IRON

AIRING

DELICATES

WOOL

The first time you turn on your dryer you should select your preferred language from the available list.

To change: the language current selection must flash, on

the first line of the display.

- Press and hold all 3 buttons: for 5 seconds.

- Press the Child Lock or the Timed Dry button to

scroll up or down through the list.

- When your required language is flashing on the top line

of the display, pressing the Dryness Level button will

select your choice.

IRON DRY

HANGER DRY

CUPBOARD DRY

Iron Dry: Dries your clothes ready for ironing.

Hanger Dry: Dries your clothes ready for hanging.

Cupboard Dry: Dries your clothes ready for wearing.

The display also shows: one, two or three blocks, depending on your selection.

These are displayed during the programmes progress.

GB

7

The Display

Programme progress

Timed drying

After selecting a programme that has a Timed Dry option, press the Timed button and the display will increment

the selected time, each time you press and release the button (see Start and Programmes).

Delay and Time to End

Some programmes can have a delated start (see Start and Programmes). Press the Delay button and the icon flashes.

The second line of the display shows the status of the programme as it progresses:

(long messages scroll across the line)

If the Mixed Dry option is available and selected this line displays when the different dryness levels have

been reached:

PRE CARE

DRY

COOL TUMBLE

END OF CYCLE, POST CARE PHASE (if option available

and selected).

END OF CYCLE, EMPTY THE WATER BOTTLE

IRON DRY REACHED

HANGER DRY REACHED

Each press advances:

then , and then repeats.

Delicates have a maximum time of:

The bars to the right of the time, light to give an indication of

the time duration selected:

The selected time remains displayed after the programme

starts.

1:40

o:20 0:30 1:00 1:30 2:00 2:40 3:00

OFF

0:20 0:30 1:00 1:30 2:00 2:40 3:00

Each press of the Delay button advances the delay setting

in 1 hour increments, from: to , then and

then after a couple of seconds cancels the delay.

The delay time is shown on the display next to the Delay button.

The display counts down the minutes of the delay period after

the Start/Pause button is pressed.

The second line of the display shows STARTS IN

1h 24h

After the delay period finishes (or for all of the programme if delay not selected): The estimated Time to End of the

programme for automatic programmes or the actual time remaining during the Timed programme is shown in this part of

the display.

(if option available and selected).

8

GB

The Display

Start and Programmes

Warnings

The second line of the display also gives warnings and reminders:

(reminders occur at the end of the programme)

END OF CYCLE, EMPTY THE WATER BOTTLE

●

Reminder that the water container should be

emptied every time you use the dryer (see

Maintenance).

EMPTY WATER BOTTLE

●

Indicates that the water container is full. The

message will take a few seconds to go out after

replacing the empty water container; the dryer

must be running for this to happen (see The

Controls).

Note: If the water container fills and this message

is displayed, the heat is turned off and your

clothes will not dry.

CLEAN CONDENSER

●

This message indicates that you must clean the

Condenser unit (see Maintenance) and will occur

at intervals depending how much you have used

the dryer. When you finish the next programme the

message is cancelled.

CLEAN FILTER

●

Reminds you to clean the Filter every time you use

the dryer (see Maintenance).

Choosing a programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see

Laundry).

3. Open the door and make sure the filter is clean

and in place and the water container is empty and

in place (see Maintenance).

4. Load the machine and make sure items are not

in the way of the door seal. Close the door.

5. If the Display is not lit: Press the ON/OFF button

6. Press the Programmes Selection button that

corresponds with the type of fabric being dried by

checking the Programmes Table (see Programmes)

as well as the indications for each type of fabric (see

Laundry).

- If the button is selected; steps 7, 8 and 9 are not

required (see below).

7. Choose Timed Drying or Dryness Levels option:

- If Timed Drying press and release the Timed

button until the required time is displayed.

or - To change from default dryness setting, press

and release the Dryness Levels button until

required level is indicated.

! See Programmes Table, for more details.

8. Set a delay time and other options if necessary

(see The Display).

9. If you wish the buzzer to sound at the end of the

programme, press the ALARM button .

10. Press the Start/Pause button to begin.

The display will show the estimated time to end.

During the drying programme, you can check on

your laundry and take out items that are dry while

others continue drying. When you close the door

again, press the Start/Pause button in order to

resume drying.

11. During the last few minutes of Drying Programmes,

before the programme is completed, the final COOL

TUMBLE phase is entered (fabrics are cooled),

this phase should always be allowed to complete.

12. The buzzer (if option selected) will warn you when

the programme is complete and the Display

shows END OF CYCLE, POST CARE PHASE .

Open the door, take the laundry out, clean the filter

and replace it. Empty the Water Container and

replace it (see Maintenance).

If the Post Care Option has been selected and

you do not remove the laundry immediately, the

dryer will tumble occasionally for 10 hours or until

you open the door.

13. Unplug the dryer.

Memory button :

First time you press this button the second line of the display will show PRESS AND HOLD TO STORE

After selecting your favorite programme and options you can save these settings by pressing and holding in the

Memory button for at least 5 seconds, the buzzer will then beep and the second line of the display shows MEMORY

The next time you need this programme press the button, then the Start/Pause button and this programme will run.

If you wish, you can change your stored favorite, by selecting a new programme and/or options and press and hold

in the button (as above).

GB

9

Start and Programmes

Special Programmes

Easy Iron Programme

‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which

fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The cycle

relaxes the fibres and makes them easier to iron and fold.

! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.

For best results:

1. Do not load more than the maximum capacity. These numbers refer to the dry weight:

Fabric Maximum load

Cotton and Cotton mixtures 2.5kg

Synthetics 2kg

Denim 2kg

2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put

them away in the closet. Should this not be possible repeat the programme.

The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix,

and less well on acrylic fibres and on materials such as Tencel®.

Wool Programme

●

This is a programme for tumble dryer safe garments marked with the symbol .

●

It can be used for load sizes up to 1kg (approximately 3 sweaters).

●

We recommend that garments are turned inside out before drying.

●

This programme will take about 60 minutes, but may take longer depending on the size and density of the load

and the spin speed used in your washer.

●

Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may

be slightly damp. Allow these to dry naturally as over-drying could damage garments.

! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size

and shape.

! This programme is not suitable for Acrylic garments.

The wool drying cycle of this tumble dryer has been approved by The Woolmark Company for the drying of

Woolmark garments labelled as machine wash and tumble dry, provided that the garments are dried according to

instructions on the garment label and those issued by the manufacturer of this tumble dryer (M0616).

This is the first and only wool drying cycle approved by The Woolmark Company.

Mini Load

Available with Cotton High Heat and Synthetic programmes. Used for loads between 1 and 2kg.

This programme optimises Automatic programme for smaller loads and improves the Time to End estimation.

Programme option modifiers

Mixed Dry

Available with Cotton High Heat and Synthetic programmes.

This option used after selecting either a Cupboard Dry or Hanger Dry dryness level. This allows you to remove

items when they have reached Hanger Dry or Iron Dry.

When the dryer detects that the load has reached Iron Dry, the display shows: IRON DRY REACHED and the

buzzer sounds for 2 minutes, open the door and remove items that you need to iron.

Then close the door and press the Start/Pause button and the programme resumes.

! If you do not open the door during the 2 minute period, the dryer will resume drying without you pressing the

Start/Pause button.

Hanger Dry programme then continues and ends with END OF CYCLE. EMPTY THE WATER BOTTLE

Cupboard Dry programme continues until the dryer detects that the load has reached Hanger Dry, the display

shows: HANGER DRY REACHED and the buzzer sounds for 2 minutes, open the door and remove any items that

you need to hang up to finish drying.

Then close the door and press the Start/Pause button and the programme resumes.

! If you do not open the door during the 2 minute period, the dryer will resume drying without you pressing the

Start/Pause button.

When Cupboard Dry dryness level reached, the dryer completed the cool tumble (and, if selected, Post Care) and

ends with END OF CYCLE. EMPTY WATER BOTTLE

10

GB

Start and Programmes

Programmes Table

Programme

What it does... How to set it... Note:

Cottons

High Heat

Dries your Cotton

clothes on High Heat.

Options available:

Alarm , Time Delay ,

Pre Care , Post Care ,

Mini Load ,

*Mixed Dry

Options available:

Alarm , Time Delay ,

Pre Care , Post Care ,

Mini Load ,

*Mixed Dry

1. Press the Cottons - High Heat button.

2. Choose Timed or Automatic option.

- If Timed Drying , see next page, or...

- To change from default dryness setting

press and release Dryness Levels button

until the required level is displayed.

3. Select any Options if required.

4. Press the Start/Pause button .

Cottons

Low Heat

Dries your Cotton

clothes on Low Heat.

Options available:

See Timed , next page.

1. Press the Cottons - Low Heat button.

2. Select a drying time, see Timed , next

page.

Brief programme

(approximately 10

minutes) that softens

fibres of clothing that is

ready for ironing.

! This is not a drying

programme (see previous

page).

Options available:

Alarm

1. Press the Easy Iron button.

2. Select Alarm option if required.

3. Press the Start/Pause button .

Synthetics

Dries your Synthetic

clothes on High Heat.

1. Press the Synthetics button.

2. Choose Timed or Automatic option.

- If Timed Drying , see next page, or...

- To change from default dryness setting

press and release Dryness Levels button

until the required level is displayed.

3. Select any Options if required.

4. Press the Start/Pause button .

Delicates

(e.g. Acrylics)

Dries your clothes on

Low heat setting, ready

to be worn.

1. Press the Delicates button.

2. If Timed programme required (see

Timed next page).

Otherwise default is Automatic.

3. Select any Options, if required.

4. Press the Start/Pause button .

Wool

Dries your Woollen

clothes, (see previous

page).

Options available:

Alarm

●

An Automatic programme

1. Press the Wool button.

2. Select Alarm option if required.

3. Press the Start button .

Airing

Easy Iron

20-minute programme

that airs your clothes

with cool air. Use also to

cool warm clothes.

1. Press the Airing button.

2. Select Alarm option if required.

3. Press the Start/Pause button .

! If the Display is not lit; Press the ON/OFF button and then select programme.

: default

Options available:

Alarm , Time Delay ,

Pre Care , Post Care .

●

The default is Automatic

Options available:

Alarm

: default

Bed & Bath

Dries your towels and

bedding on High Heat.

Options available:

Alarm , Time Delay ,

Pre Care , Post Care

●

An Automatic programme

1. Press the Bed & Bath button.

2. Select any Options if required.

3. Press the Start/Pause button .

Dryness options: Automatic

IRON DRY

HANGER DRY

CUPBOARD DRY

Dryness options: Automatic

IRON DRY

HANGER DRY

CUPBOARD DRY

Note: *Mixed Dry only available with Cupboard Dry and Hanger Dry (see Programme option modifiers).

GB

11

Start and Programmes

Timed Drying

Timed programmes table: First select a programme (see Programmes Table).

(0:20, 0:30,

1:00, 1:30, 2:00,

2:40 or 3:00

Hours:Minutes)

Always use Timed Drying

for loads less than 1kg, or

if you prefer a different

dryness result.

The heat setting depends

on the programme

(material option) selected.

Consult suggested drying

times (see Laundry).

The last 10 minutes of these

programmes is the Cool

Tumble phase .

1. Press and release the Timed button

until the display shows the required

selection. Each press advances ,

, , , , , then

and then repeats.

●

Delicates have maximum time of .

●

When is displayed, Automatic

option is available if you change your

mind.

2. Select any Options if required.

3. Press the Start button .

Options available:

Alarm , Time Delay ,

Pre Care , Post Care .

! Warning, after pressing the Start/Pause button ,

the programme cannot be changed.

To change a selected programme, press the

Start/Pause button , the light flashes Amber to

indicate the programme is paused. Select the new

programme and any options required, the light will

then flash green. Press the Start/Pause button

again and the new programme will start.

●

Option buttons / icons

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected, by pressing a programme selection

button, before an option can be selected. Not all

options are available for all programmes (see

Programmes Table). If an option is not available and

you press the button, the buzzer will beep 3 times. If

the option is available the indicator, on the display unit

next to the bottom buttons, lights to show that the

option has been selected.

Time Delay

The start of some programmes (see The Display and

Start and Programmes) can be delayed for up to 24

hours. Ensure the water container is emptied before

setting a delayed start.

Pre Care

This option is only available if a delayed start has

been selected. It tumbles the clothes occasionally

during the delayed period to help prevent creases

developing.

Alarm

Available on all programmes and allows the buzzer to

give a signal at the end of the drying cycle, to remind

you that the clothes are ready to be removed.

Post Care

When available and selected, the clothes are

occasionally tumbled after the end of the drying and

cool tumble cycles, to help prevent creases

developing should you not be available to remove the

load immediately the programme is complete.

●

TIME DISPLAY

The display shows either the amount of time delay

remaining or an indication of the amount of time left for

a drying programme (see The Display).

The delay or time to end is displayed in hours and

minutes and counts down each minute.

When timed programmes are selected the time

displayed throughout the cycle is the actual time

The Controls

88:88

remaining.

When an Automatic programme is selected, the time

displayed is an estimate of the time remaining. When

the programme is selected the display shows the time

required to dry a full load, after around 10 minutes the

controller calculates a better estimate of the cycle time.

The colons between the hours and minutes in the

display flash to show that the time is counting down.

The display also shows if there is a problem with your

dryer, if this occurs the display will show F followed by

a fault code number (see Troubleshooting).

●

Empty Water Container

(If you have plumbed your dryer to a drain this icon can

be ignored, as there is no need to empty the water

container).

Messages are displayed to reminds you to empty the

water container.

If the water container fills during a programme, the

heater turns off and the dryer does a period of Cool

Tumble. After this it stops and a message tells you to

EMPTY THE WATER CONTAINER .

You must empty the water container and restart the

dryer or the clothes will not dry. After re-starting the

dryer the message will take a few seconds to go out.

To avoid this always empty the water container each

time you use the dryer (see Maintenance).

●

Door Opening

Opening the door during a programme will stop the

dryer and have the following effects:

●

The display shows PAUSED .

●

During a delay phase the delay will continue to

count down. The Start/Pause button must be

pressed to resume the delay programme.

The display will change to show current status.

●

During the drying part of the programme, the

colons on the display stop flashing to show that

the time has stopped counting down.

The Start/Pause button must be pressed to

resume the programme. The display will change to

show the current status, the colons flash and count

down continues.

●

During the Post Care phase, the programme ends.

Pressing the Start/Pause button will restart a new

programme from the beginning.

●

Note

If you have a power cut, switch off the power or

remove the plug. When power is restored, press the

Start/Pause button and the programme will resume.

0:20

0:30 1:00 1:30

2:00

2:40

3:00

1:40

12

GB

Laundry

Sorting your laundry

●

Check symbols on clothing labels to make sure

that the articles can be tumble dried.

●

Sort laundry by fabric type.

●

Empty pockets and check buttons.

●

Close zippers and hooks and tie loose belts and

strings.

●

Wring out each item in order to eliminate as much

excess water as possible.

! Do not load dripping wet clothes into the dryer.

Maximum load size

Do not load more than maximum capacity.

These numbers refer to dry weight:

Natural fibres: 8kg max (18lb)

Synthetic fibres: 3kg max (6.6lb)

! DO NOT overload the dryer as this could result in

reduced drying performance.

Typical weights

Note: 1kg = 1000g (1lb = 16oz)

Clothes

Blouse Cotton 150g (5oz)

Other 100g (3oz)

Dress Cotton 500g (1lb 2oz)

Other 350g (12oz)

Jeans 700g (1lb 6oz)

10 nappies 1000g (2lb 3oz)

Shirt Cotton 300g (10oz)

Other 200g (7oz)

T-Shirt 125g (4oz)

Household Items

Duvet cover Cotton 1500g (3lb 5oz)

(Double) Other 1000g (2lb 3oz)

Large Tablecloth 700g (1lb 6oz)

Small Tablecloth 250g (9oz)

Tea Towel 100g (3oz)

Bath Towel 700g (1lb 6oz)

Hand Towel 350g (12oz)

Double Sheet 500g (1lb 2oz)

Single Sheet 350g (12oz)

At the end of a drying cycle, cottons could still be

damp if you grouped cottons and synthetics together.

If this happens simply give them an additional short

period of drying.

●

Note: The last 10 minutes of any time set is the

Cool Tumble, so allow for this when setting the time,

as this period will not dry your laundry.

Wash Care Labels

Look at the labels on your garments, especially when

tumble drying for the first time. The following symbols

are the most common:

May be tumble dried

Do not tumble dry

Tumble dry at high heat setting

Tumble dry at low heat setting

Items not suitable for tumble drying

●

Articles that containing rubber or rubber-like

materials or plastic film (pillows, cushions, or PVC

rainwear), any other flammable articles or objects

that contain flammable substances (towels soiled

with hair spray).

●

Glass fibres (certain types of draperies)

●

Items which have been dry cleaned

●

Items with the ITCL Code (see Special

clothing items). These can be cleaned with special

at-home dry cleaning products. Follow instructions

carefully.

●

Large bulky items (quilts, sleeping bags, pillows,

cushions, large bedspreads etc). These expand

when drying and would prevent airflow through

the dryer.

GB

13

Laundry

Special clothing items

Blankets and Bedspreads: acrylic items (Acilan,

Courtelle, Orion, Dralon) must be dried with special

care on LOW heat setting. Avoid drying for a long

period of time.

Pleated or creased garments: read the manufacturer’s

drying instructions on the garment.

Starched articles: do not dry these with non-starched

items. Make sure that as much of the starch solution is

removed from the load as possible before placing it in

the dryer. Do not over-dry: the starch will become

powdery and leave your clothing limp, which defeats

the purpose of starch.

Drying times

Times are approximate and can vary depending

upon:

●

Amount of water retained in clothes after spin

cycle: towels and delicates retain a lot of water.

●

Fabrics: items that are the same type of fabric but

different textures and thicknesses may not have

the same drying time.

●

Quantity of laundry: single items or small loads

may take longer to dry.

●

Dryness: If you are going to iron some of your

clothes, they can be taken out while still a bit

damp. Others can be left longer if you need them

to be completely dry.

●

Heat setting.

●

Room temperature: if the room where the dryer is

located is cold, it will take longer for the dryer to

dry your clothes.

●

Bulk: some bulky items can be tumble dried with

care. We suggest that you remove these items

several times, shake them out, and return them to

the dryer until finished.

! Do not over-dry your clothes.

All fabrics contain a little natural moisture, which

keeps them soft and fluffy.

The table (see below) presents APPROXIMATE drying

times in Hours : Minutes, as you see them on the

display, the times are also shown in Minutes only for

reference.

The times given are for Cupboard Dry Automatic

programmes.

Timed Dry settings are also shown, to help you

choose a suitable time option.

Weights refer to dry garments.

Cottons

High Heat

Synthetics

High Heat

Delicates

(Acrylics)

Low Heat

Drying times 800-1000 rpm in washing machine.

Drying times on reduced spin in washing machine.

Automatic duration

Automatic minutes

Timed Dry setting

Automatic duration

Automatic minutes

Timed Dry setting

Automatic duration

Automatic minutes

Timed Dry setting

Half Load

1 kg

2 kg

4 kg

3 kg

1 kg

2 kg

1 kg

2 kg

3 kg

5 kg

6 kg

7 kg

0:30 - 0:50

0:40 - 0:55

1:10 - 1:20

0:55 - 1:10

1:20 - 1:30

1:40 - 2:20

2:20 - 2:30

30 - 50

50 - 70

80 - 100

70 - 80

100 - 120

120 - 140

140 - 160

0:20 or 0:30 or 1:00

0:30 - 0:40

30 - 40

0:30 or 1:00

0:40 - 1:20

40 - 80

0:40 or 1:00 or 1:20

1:20 - 2:00

80 - 140

1:20 or 1:40

0:40 - 0:50

40 - 50

1:00

1:10 - 1:30

50 - 70

1:00 or 1:30

1:30

1:00 or 1:30

1:30 or 2:00

2:00 or 2:40

8 kg

2:30 - 2:50

150 - 170

2:40 or 3:00

Half Load

Full Load

14

GB

Warnings and Suggestions

! The appliance has been designed and built according

to international safety standards.

These warnings are given for safety reasons and must

be followed carefully.

General safety

●

This tumble dryer is not intended for use by

persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

●

This tumble dryer has been designed for home,

and not professional use.

●

Do not touch the appliance while barefoot or with

wet hands or feet.

●

Unplug the machine by pulling on the plug, not

the cord.

●

Children must not be in proximity of the dryer

when in use. After using the dryer, turn it off and

unplug it. Keep the door closed to make sure that

children do not use it as a toy.

●

Children should be supervised to ensure that they

do not play with the dryer.

●

The appliance must be installed correctly and

have proper ventilation. The air intake at the front

of the dryer and rear vent behind the dryer should

never be obstructed (see Installation).

●

Never use the dryer on carpeting where the pile

height would prevent air from entering the dryer

from the base.

●

Check to see if the dryer is empty before loading it.

●

The back of the dryer could become very

hot. Never touch it while in use.

●

Do not use the dryer unless the filter, water

container and condenser are securely in place

(see Maintenance).

●

Do not use liquid fabric softeners in the dryer, add

it to the final rinse of your wash.

●

Do not overload the dryer (see Laundry for

maximum loads).

●

Do not load items that are dripping wet.

●

Tumble dry items only if they have been washed

with detergent and water, rinsed and been through

the spin cycle. It is a fire hazard to dry items that

HAVE NOT been washed with water.

●

Carefully check all instructions on clothing labels

(see Laundry).

●

Do not dry garments that have been treated with

chemical products.

●

Never dry articles that are contaminated with

flammable substances (cooking oil, acetone, alcohol,

petrol, kerosene, spot removers, turpentine, waxes,

wax removers and hair sprays), unless washed in

hot water with an extra amount of detergent.

●

Do not tumble dry rubber, rubber backed articles and

clothes, pillows fitted with foam rubber pads, foam

(latex foam), rubber, plastic, shower caps, waterproof

textiles, nappy pants or liners, polythene or paper.

●

Do not tumble dry large, very bulky items.

●

Do not tumble dry acrylic fibres at high temperatures.

●

Remove all objects from pockets, especially

lighters (risk of explosion).

●

Complete each programme with its Cool Tumble Phase.

●

Do not turn off the dryer when there are still warm

items inside.

●

Clean the filter after each use (see Maintenance).

●

Empty the water container after each use (see

Maintenance).

●

Clean the condenser unit at regular intervals

(see Maintenance).

●

Do not allow lint to collect around the dryer.

●

Never climb on top of the dryer. It could result in damage.

●

Always follow electrical standards and requirements

(see Installation).

●

Always buy original spare parts and accessories

(see Service).

! WARNING: Never stop the dryer before the end of the

drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated.

Recycling and disposal information

As part of our continued commitment to helping the

environment, we reserve the right to use quality recycled

components to keep down customer costs and minimise

material wastage.

●

Disposing of the packaging material: follow local

regulations, so the packaging can be recycled.

●

To minimise risk of injury to children, remove the

door and plug - then cut off mains cable, flush

with the appliance. Dispose of these parts separately

to ensure that the appliance can no longer be

plugged into a mains socket.

Disposal of old electrical appliances

The European Directive 2002/96/EC on Waste Electrical

and Electronic Equipment (WEEE), requires that old

household electrical appliances must not be disposed

of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to

optimise the recovery and recycling of the materials

they contain and reduce the impact on human health

and the environment.

The crossed out “wheeled bin” symbol on

the product reminds you of your obligation,

that when you dispose of the appliance it

must be separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct disposal

of their old appliance.

Saving energy and respecting the

environment

●

Wring out items to eliminate excess water before

tumble drying (if you use a washing machine first,

select a high spin cycle). Doing this will save time

and energy during drying.

●

Always dry full loads - you save energy: single

items or small loads take longer to dry.

●

Clean the filter after each use to contain energy

consumption costs (see Maintenance).

GB

15

Maintenance and Care

Cleaning the drum

! Do not use abrasives, steel wool or stainless steel

cleaning agents to clean the drum.

A coloured film may start to appear on the stainless

steel drum, this may be caused by a combination of

water and, or cleaning agents such as fabric conditioner

from the wash. This coloured film will not affect the

dryer performance.

Cleaning the condenser unit

Periodically (every month) remove the condenser unit

and clean any build up of fluff from between the plates

by rinsing it under the tap with cold water.

This should be done with cold water from the rear of

the condenser.

Removing the condenser:

1. Unplug the dryer and open the door.

2. Pull open the condenser cover (see diagram).

Release the three catches by turning 90˚ counter-

clockwise then pull on the grip and remove from

the dryer.

3. Clean the surface of the seals and replace, making

sure that the catches have been secured.

Cleaning the dryer

●

External parts in metal or plastic and rubber parts

can be cleaned with a damp cloth.

●

Periodically (every 6 months) vacuum the front air

intake grille and vents at the rear of the dryer, to

remove any build up of fluff, lint or dust. Also to

remove accumulation of fluff from the front of the

condenser and filter areas, clean occasionally with

a vacuum cleaner.

! Do not use solvents or abrasives.

! Your dryer uses special bearing components which

do not need lubrication.

! Have your dryer checked regularly by authorised

technicians to ensure electrical and mechanical safety

(see Service).

Switching off the electricity

! Unplug your dryer when not using it, when cleaning

it and during all maintenance operations.

Clean the filter after each cycle

The filter is an important part of your dryer:

it accumulates lint and fluff that is formed while drying.

When finished drying, clean the filter by rinsing it

under running water or with your vacuum cleaner.

Should the filter become clogged up, the airflow inside

the dryer will be seriously compromised: drying times

lengthen and you will consume more energy. It may

also damage your dryer.

The filter is found in front of the dryer trim (see diagram).

Removing the filter:

1. Pull the plastic grip of the filter upwards (see diagram).

2. Clean the filter and replace it correctly.

Ensure the filter is fully located flush into the tumble

dryer trim.

! Do not use the dryer without replacing the filter.

Empty the water container after each

cycle

Pull the container out of the dryer and empty it into a

sink or other suitable drain.

Replace the water container securely.

Always check and empty the container before you

start a new drying programme.

Check the drum after each cycle

Turn the drum manually in order to remove small items

(handkerchiefs) that could have been left behind.

Water container

Handle

Condenser cover

Catches

Air intake

Filter

Tap

Rear

Front

Condenser unit

16

GB

Troubleshooting

One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the

following troubleshooting suggestions:

Possible causes / Solution:

●

The plug is not plugged into the socket, or not making contact.

●

There has been a power failure.

●

The fuse has blown. Try to plug another appliance into the socket.

●

You are using an extension cord? Try to plug the dryer’s power cord

directly into the socket.

●

The door is not closed securely?

●

The programme has not been set properly (see Start and Programmes).

●

The Start/Pause button has not been pressed (see Start and Programmes).

●

You have set a delayed time (see Start and Programmes).

●

The filter has not been cleaned (see Maintenance).

●

The water container needs emptying? The empty water message is

displayed? (see Maintenance).

●

The condenser needs cleaning? (see Maintenance).

●

The temperature setting is not ideal for the type of fabric you are drying

(see Start and Programmes, and see Laundry).

●

The correct drying time has not been selected for the load (see Laundry).

●

The air intake grille or rear vents are obstructed (see Installation, and see

Maintenance).

●

The items were too wet (see Laundry).

●

The dryer was overloaded (see Laundry).

●

The water container was probably not emptied at the start of the

programme. Do not wait for the empty water signal, always check and

empty the container before starting a new drying programme (see

Maintenance).

●

This is normal, the: END OF CYCLE, EMPTY THE WATER BOTTLE

message is shown as a reminder to empty the container (see The Display

and Start and Programmes).

! For safety the dryer has a maximum programme time of 4 hours. If an

automatic programme has not sensed the required final moisture in this time

the dryer will complete the programme and stop. Check the above points

and run the programme again, if the results are still damp, contact the

Service Centre (see Service).

●

If the display shows F10 or F15:

- Turn off and remove the plug. Clean the filter and the condenser

(see Maintenance). Then replace the plug, turn on and start another

programme. If F10 or F15 is still displayed contact the Service

Centre (see Service).

●

If any other number is shown: Note down the code and contact the

Service Centre (see Service).

●

The dryer is in ‘Demo’ mode. Press and hold both the On/Off and

Start/Pause buttons for 3 seconds. The display will show DEMO OFF for

3 seconds and then the dryer will resume normal operation.

Problem:

The tumble dryer won’t start.

Drying cycle will not begin.

Its taking a long time to dry.

Empty water message is

displayed but the dryer has

only been running for a short

period.

Empty water message is

displayed and the water

container is not full.

Programme finishes and

clothes are damper than

expected.

The display shows a fault

code F followed by one or two

numbers.

The display briefly shows

DEMO ON every 6 seconds.

Service

GB

17

Spare Parts

This dryer is a complex machine. Repairing it yourself

or having a non-authorised person try to repair it could

cause harm to one or more persons, could damage

the machine and could invalidate the spare parts

warranty.

Call an authorised technician if you experience problems

while using the machine.

The spare parts have been designed exclusively for

this appliance and not for other uses.

Before calling the Service Centre:

●

Use the troubleshooting guide to see if you can

solve the problem yourself (see Troubleshooting).

●

If not, turn off the dryer and call the Service Centre

closest to you.

What to tell the Service Centre:

●

name, address and post code.

●

telephone number.

●

the type of problem.

●

the date of purchase.

●

the appliance model (Mod.).

●

the serial number (S/N).

This information can be found on the data label inside

the door of the machine.

Comparative Programmes

●

Programmes recommended for comparative test to EN61121

! Note: This is not a full list of programme options (see Start and Programmes).

This appliance conforms to the following EC Directives:

- 2006/95/EC (Low Voltage Equipment)

- 89/336/EEC, 92/31/EEC and 93/68/EEC (Electromagnetic Compatibility)

Programme Programme to select Load size Dryness Option

(EN61121)

Dry Cotton COTTONS HIGH HEAT 8 kg HANGER DRY

Iron Dry Cotton COTTONS HIGH HEAT 8 kg IRON DRY

Easy-care textile SYNTHETICS 3 kg CUPBOARD DRY

Page is loading ...

195079672.00 W

08/2009 - SIMLEX . Four Ashes, Wolverhampton

88

HOTPOINT/ARISTON TCD G51 B (SK) User guide

HOTPOINT/ARISTON TCD G51 B (SK) User guide

in other languages

Related papers

Other documents