Octane Fitness Q47ce Assembly Manual

Brand: Octane Fitness

Model: Q47ce

Type: Assembly Manual

Q47e/Q47ce

Q47e/Q47ce ASSEMBLY INSTRUCTIONS

PERSONAL RECORD KEEPING

IMPORTANT: Record the serial numbers of your Octane Fitness® elliptical in the spaces below. This will

make it easier for you to obtain accurate and timely response should any service issues occur with your

elliptical machine. Also, don’t forget to register your warranty on the web at www.octanefitness.com.

ATTENTION – All serial numbers begin with a letter.

Base Serial Number – located below front right chrome rail at the power inlet

__ __ __ __ __ __ __ __ __ __ __ __ __ __

Console Serial Number – located on the lower edge of the console

__ __ __ __ __ __ __ __ __ __ __ __ __ __

If you have any additional questions or need additional assistance in assembly, please contact your local service

provider or Octane Fitness Customer Service at 1.888.OCTANE4 ext. 1. You may also visit us on the web at

www.octanefitness.com.

WARNING: Machine contains moving parts. Use caution when assembling and operating this machine.

This product is intended for household use.

Q47e/Q47ce Contents

The Octane Fitness base box contains the following: Tools required:

 A) 1-OctaneFitnesscrosstrainerbase • Phillipsscrewdriver

 B) 1-Consolemast • 17mmwrenchoradjustablewrench

 C) 1-Topcover • 17mmsocketandratchet

D) 1 - Access panel • 6mmhexkeywrench

E) 1 - Detached right pedal lever

F) 1 - Left moving handlebar

G) 1 - Right moving handlebar

H) 2 - Handlebar covers

I) 1 - Mast boot

 J) 1-Hardwarepack(seeoppositepage)

Box Contents

EFG

Hardware Pack (J) includes:

 K) 8-6mmhexkeychamferedbolt(formovinghandlebar)

 L) 2-Phillipsscrews(formountingaccesspanel)

 M) 2-Phillipsscrewswithwashers(formountingtopcover)

 N) 1-Cabletie(forsecuringloosewirestomast)

Moving the Product

It is safest to move the product to its installation location in its shipping carton. It may be easier to move the

productintoyourhome after you remove it from the packaging, but be careful not to hit any walls or doors.

TheQ47e/Q47cefeaturestransportwheelsonthefrontoftheunit.Becarefulwhenmovingfromonesurfaceto

another, such as hardwood floor to carpet.

Note: If you need to pick up your elliptical there are hand placement slots under the front shroud. Please take

caution when lifting. The elliptical weighs 280 lbs. when fully assembled.

Tip: When using the front transport wheels, it is easier to pull the unit rather than push it.

KL M

The Q47/Q47ce console box contains the following:

1) 1 - Deluxe console

 2) 1-Deluxekeypad

 3) 2-Consolebackarcs(leftandright)

 4) 1-Powersupply

5) 1 - Octane Fitness™ wireless heart rate transmitter and elastic strap

 6) 1-Informationpacket

 7) 4-Phillips18mmscrews(notpictured)

 8) 4-Phillips12mmscrews(notpictured)

Q47/Q47e/Q47ce

Beginner

10K PowerWalk Stride Interval Dual Direction Stride Burst

CALORIES STRIDE

Quick

Start

My Qu ic k

Start 1

My Qu ic k

Start 2

ArmBlaster Glute

Kicker

Enter

Cool

Down Pause

Clear

Now-Zone

Time

Program

Stride

Level

Weight

Age

Fan

The Q47ce console box also contains the Contact Heart Rate (ce) kit(notpictured),whichincludes:

a) 1- Cable assembly for heart rate grips

b) 2 - Left side grips

c) 2 - Right side grips

 d) 2-Rubbergaskets

e) 4 - 2mm hex head screws

 f) 1-2mmhexkeywrench

 g) 2-Primary(top)contactplates

 h) 2-Secondary(bottom)contactplates

2. Attach moving handlebars—Moving handlebars are

labeled left and right, be sure to install accordingly.

a. Align the bottom of the handlebar with the four holes in

the pivot shaft and attach with four 6mm hex key bolts

(K)—make sure these bolts are very tight; torque to 30

ft-lbs.

b. Reaching inside from the front of the machine, carefully con-

nectthecablecomingfromthebaseofthehandlebar(For

G) to the cable by the pivot shaft. Gently tug both cables

to ensure the connectors are completely seated.

c. Position the handlebar cover (H) over the handlebar pivot

point and press firmly at top and bottom to attach.

d. Repeat for the other side.

Pivot shaft

Cable from

handlebar

Cable on

frame

1. Attach pedal lever

a. Removeboltfrom3-pivotlink.

b. Placeright pedallever(E)throughleg slotinrearshroudand

attachittothe3-pivotlink.Check to see that the rollers are

seated and properly aligned on the rails before securing

the pedal lever.

c. Tighten the bolt and nut securely using 17mm socket and

wrench.

3. Install access panel

a. Loosen the screws on the left and right sides of the lower

shroudnearthefrontoftheunit.(Thesescrewssecurethe

side of the shroud and the access panel to the frame.)

b. Slidethemetal plate oftheaccess panel (D)behindthe

backshroud.Fitthetabsoneachsideoftheaccesspanel

into the slots between the side of the main shroud and the

frame, over the top of the screws.

c. Tightenthescrewsoneachside,thensecurethebackof

theaccesspanelwith2Phillipsscrews(L).

Tabs Slot for

Tab

Back

Screws

Screw to

loosen on

both sides

4. Install console mast

a. Attachtheconsolemast(B)byplacingthekeyholeslotsinthe

mast plate over the bolts and sliding the console mast toward

the pedals.

b. Tightenthefour6mmhexkeyboltsattachingconsolemastto

frame.

c. Connect the black cable connector coming from the mast

to the black cable connector on the base frame. Tug the

cables gently to ensure the connectors are completely

seated.

d.Usethecabletie(N)tosecureanyloosecabletothebottom

of the mast; cut off any excess cable tie.

5. Mount the keypad to the console mast

If you have the Q47e keypad:

a. Removethetwoscrewssecuringtheconsolebackpiece

to the mast plate.

b. Route the cable from the heart rate board down through

the top of the mast tube and out of the hole beneath the

console plate.

c. Route the red and white fan wires with the white

connector down through the top of the mast tube and out

of the hole beneath the console plate.

d. Attachtheblackribboncableconnectorfromthetopof

theconsolemast tube to itsconnectiononthe back of

the keypad (2). Tug the cables gently to ensure the

connectors are completely seated.

e. Positionthekeypad(2)onthemast(B)andinserteachof

the 4 shorter screws through the mast holes and into the

keypadback.Tightenscrewstosecure.

If you have the Q47ce keypad:

a. Removethetwoscrewssecuringtheconsolebackpiece

to the mast plate.

b. Use a utility knife to cut the rubber grips and remove

them from the stationary handlebars.

c. Leading with the white plastic connector, insert the

contact heart rate cable (a) through the hole in the

“user’s right” side of the mast and feed it up through the

mast tube.

d. Feed the cable for the right grip, labeled “Right Hand

Contact”, up through the right handlebar tube.

e. Feed the cable for the left grip through the hole in the

“user’s right” side of the mast and through the hole on

the “user’s left” side, then feed it up through the left

handlebar tube.

f. Select a ‘left’ side grip (b), differentiated from a right

sidegrip(c)bytwoscrewholes.Placearubbergasket

(d)intothelefthalfofthecontactgrip,andpositionon

the left handlebar.

g. Positionthesmallwhitewireoutintheslotatthetopof

thelefthalfofthehandgrip(thesideclosesttoauser

standingonthepedals).Positionthesmallredwirein

theslotatthebottomofthehandgrip(awayfromthe

user).

h. Selecta‘right’sidegrip(c),fititwiththelefthalfaround

the handlebar, and secure the two halves together using

two2mmscrews(e).Makesurethatthewiresareinthe

slots, not clamped between the grips; tighten the screws

until that the grip is stable.

i. Selectaprimarycontactplate(g)thatmatchesthecontour

ofthetopoftheplasticgrip(closesttoauser).Peelthe

blue protective film off of the tab on the primary contact

plate(g),thenslidethetabintotheconnectorattheend

of the small white wire.

j. Select a secondary contact plate (h) that matches the

contourofthebottom of the plastic grip (awayfromthe

user).Peel the blue protecting film off of the tab on the

secondary contact plate (h) and slide the tab into the

connector at the end of the remaining wire.

k. Repeatsteps(f)through(k)fortherighthandlebar.

l. Pushanyextralengthsofwireintothemasttube.

m. Insert the connector at the end of the heart rate cable into

itsconnectoronthe heart rate board on thebackofthe

keypad.(This is a two-wire cable ending in a single

connector.) Route the contact heart rate cable wires

aroundthepostsonthebackofthekeypad,inthesame

mannerthattheotherheartratecableisrouted(seefigure

at right).

n. Route the cable from the other end of the heart rate board

down through the top of the mast tube and out of the hole

beneath the console plate.

o. Route the red and white fan wires with the white connector

down through the top of the mast tube and out of the hole

beneath the console plate.

p. Attachthe blackribbon cableconnector fromthe keypad

(2) to its cable coming from the top of the mast. Tug

the cables gently to ensure the connectors are

completely seated.

q. Positionthekeypad(2)onthemast(B)andinserteachof

the 4 shorter screws with washers through the mast holes

andintothekeypadback.Tightenscrewstosecure.

r. Remove the film from the adhesives on the primary

contact plates (g) and secondary contact plates (h)

and carefully press the plates onto the grips, pushing

the tabs, connectors, and wires inside the grips.

It is recommended that you wait to adhere the grips

until after you have installed the console and verified

that the contact heart rate grips are transmitting a

reading to the console.

Console/Keypad

Connection

(all models)

Standard

Heart Rate

Connection—

Q47e/Q47ce only

Contact Heart Rate

Connection—

Q47ce only

Fan Wire—

Q47e/Q47ce only

Keypad Ground

Connection

(all models)

Route

Contact Heart Rate Cables

Here

Contact Heart Rate Board

Connector for

Grip Wire

Note: If you are using the optional LCD Mounting Arm,

skip step 6 of these instructions and instead follow the

instructions included with the LCD Mounting Arm. Once

you have completed those instructions, resume assembly

of your Q47e/Q47ce with step 7 of these instructions.

6. Mount the console to the console mast

Note: Record the serial number of your console, located on the lower edge of the console, before

attaching the console to the console mast. (If you have installed the optional LCD Mounting Arm,

and mounted the console to the mast according to those instructions, skip to Step 7.)

If you have the Q47e/Q47ce console:

a. Positiontheconsole(1)ontheplateatthetopofthemast

(B)andplacetheleftbackarc(3)behindit.Holdingboth

in place, insert 2 of the longer (18mm) Phillips screws

partiallythroughthebackarc(3)andthemastplateintothe

consoleback.Repeatontherightside.Tightenallscrews

to secure.

b. Attach the white 12-pin main connector to its connection on

thebackoftheconsole.Tug the cable gently to ensure

the connector is completely seated.

c. Attachtheblackkeypadconnectortoitsconnectiononthe

backoftheconsole.Tug the cable gently to ensure the

connector is completely seated.

d. Attach the metal connector on the green ground wire that

isconnectedtothebackofthemastplatetoitsconnection

onthebackoftheconsole.Tug the ground wire gently

to ensure the connector is completely seated.

e. Attach the white 3-pin heart rate connector to its connection

on the back of the console. Tug the cable gently to

ensure the connector is completely seated.

f. Attach the white 2-pin fan connector to its connection on

thebackoftheconsole.Tug the wires gently to ensure

the connector is completely seated.

g. PlugintheunitandverifythattheconsoleLEDslightand

that the Level and Stride control buttons on the moving

handlebars are working. If you have the Q47ce console,

grasp the contact heart rate handgrips and verify that a

heart rate reading appears on the console. If any issues are

detected,rechecktheconnections,orcontactOctaneFitness

Customer Service for assistance. Once you have verified

these functions, unplug and proceed with remaining steps.

h. Make sure excess cable is pushed into the mast tube.

i. Repositiontheconsolebackpieceandreattachitusingthe

two screws provided.

Keypad

(black)

All models

Heart Rate

(white, 3-pin)

Q47e/Q47ce only

Console to Base

(white, 12-pin)

All models

Fan

(white, 2-pin)

Q47e/Q47ce only

Console Ground

(metal; green wire)

All models

8. Place top cover

a Aligntopcover(C)ontopofmainhousing.Holdthebackedge

(nearthemast)inplaceandshiftthefrontedgeforwarduntil

it settles into position.

b. Whilestillholdingthebackedgeinplace,pressfirmlyonthe

bottom edge of the front of the cover until it snaps into place.

You will feel and hear it snap into place as the plastic

bracket on the inside of the front bottom edge clips

onto the steel tube at the front of the main frame.

c. Securethetopcovertotheframeusing2Phillipsscrewswith

washers(M).

7. Adjust arms (optional)

Note: Before completing this step, plug in and ride your elliptical cross trainer for a few

moments to get a feel for the arm motion. If the reach of the arm motion feels right (as it will for

most users), proceed to step 8. If the reach is too long or too short, carefully follow these steps

to shorten or extend the reach by approximately 1.5 inches:

a. Locatetherodendlinkthatconnectstotheblackbar(pivot)

insidethemachine.Theblackbarhasthreeholesinitwith

therodendlinkattachedthroughthecenterholewitha6mm

hexkeyboltanda13mmnut.Aspacerseparatestheblack

barandtherodendlink.

b. While supporting the arm, remove the 13mm nut from

the6mmhexkeyboltandcarefullyeasetheboltfromthe

centerholeintheblackbar.Toextendthereachofthearm,

re-insert the bolt in the hole closest to the front of your

elliptical trainer. To shorten the reach, re-insert the bolt in the

hole closest to the user end of the machine. Make sure that

the spacer remains in place between the rod end link

and the black bar, with the pocket side of the spacer

toward the rod end link.

c. Replace the nut and tighten. This connection must be

very tight.

d. Repeat for the other arm.

 Shouldyouhaveanyquestionsorconcernsinmakingthisadjustment,pleasecontactyourlocalservice

provider or contact Octane Fitness Customer Service at 1.888.OCTANE4, ext. 1.

Steel tube

Press here

Hold here

Secure with

screws

11. Plug in product

a. First,inserttheplugintotheproduct,locatedjustbelow

therightrollertrack.Next,routethecabletowardthewall

outlet. You can run it under the product to avoid seeing it

or tripping on the cable. Ensure that the cord will not be

pinchedand becomedamaged. Plugthe productintothe

wall.

Note: There is no need to turn off your product—your

Q47e/Q47ce was designed with an intelligent sleep

mode—a virtual off button. This eliminates the

need for an on/off switch. When your product is in

sleep mode, it uses very little power. Unplugging

your elliptical will not harm or erase My QuickStart

profiles.

10. Adjust levelers

a. Adjustallfourlevelerstomakesuretheproductsitsflaton

the floor. For a lower step up height, screw the rear levelers

into the rear stabilizer bracket. Then level the machine

using the front levelers.

b. Tighten the leveler nut against the frame for each

leveler.

Note: If you move your Q47e/Q47ce, you may need

to adjust the levelers to make sure your

product is level with the floor.

CAUTION: If the unit is not level, it may not function

properly.

9. Install mast boot

a. Placetherubbermastboot(I)aroundthemast(B),covering

the open ends of the stationary handlebars.

b. Tucktheendsofthemastboot(I)intothechannelsinthe

accesspanel(D)justbelowthestationaryhandlebars.

NOTES

FUEL YOUR LIFE™

9200 Wyoming Avenue North, Suite 380

BrooklynPark,MN55445

1.888.OCTANE4

www.octanefitness.com

trademarksofOctaneFitness.Anyuseofthesetrademarks,withouttheexpresswrittenconsentofOctaneFitness,isforbidden.

103346-001REVA

Are you passionate about your workout and the results?

Share your story with others on the Octane Fitness web site.

Go to: www.octanefitness.com/testimonials

Then click on “Share My Story” and

show the world how fueled you are.

Octane Fitness Q47ce Assembly Manual

Brand: Octane Fitness

Model: Q47ce

Type: Assembly Manual

Download PDF

report

Octane Fitness Q47ce Assembly Manual

Octane Fitness Q47ce Assembly Manual

Related papers

Other documents