Silicon Labs UG439 User guide

Brand: Silicon Labs

Model: UG439

Type: User guide

UG439: Si3474 Software User's Guide

This software distribution contains demo code to interact with the

Si3474 EVB. The demo code is supplied as Windows executables

and requires no installation. Section 2. Hardware Configuration of

this document describes the hardware setup and Section 3. De-

mos describes the demo code operation.

The demo code is written in Python and built upon a custom Py-

thon package which is included in the distribution. More advanced

users can inspect the code, run the code from Python, or run their

own Python scripts to interact with the Si3474. Section 4. Win-

dows describes the installation process for Windows machines

and Section 5. MacOS

describes the process for MacOS.

RELATED DOCUMENTS

• UG425: Si3474 EVB User's Guide

• Si3474 Data Sheet

SUPPORTED OPERATING SYSTEMS

• Windows 7, 8, 10

• MacOS

silabs.com | Building a more connected world. Rev. 0.1

Table of Contents

1. Package Contents .............................

1.1 Content Tree ..............................3

1.2 Content Description ............................3

2. Hardware Configuration ...........................4

2.1 Configuring for 4P Operations .........................5

2.2 Configuring for 2P Operations .........................6

3. Demos ..................................7

3.1 Auto Mode (4P)..............................7

3.2 Auto Mode (2P)..............................7

3.3 Semi-Auto Mode (4P)............................8

3.4 Semi-Auto Mode (2P)............................10

4. Windows ................................11

4.1 Run Demo Scripts .............................11

4.2 Installation ...............................11

4.2.1 Install Python .............................11

4.2.2 Install silabs_pse Package ........................11

4.3 Run Demo Scripts Manually .........................11

4.4 Write Custom Scripts ............................11

5. MacOS .................................12

5.1 Installation ...............................12

5.1.1 Install Python .............................12

5.1.2 Install silabs_pse Package ........................12

5.2 Run Demo Scripts .............................12

5.3 Write Custom Scripts ............................12

silabs.com | Building a more connected world. Rev. 0.1 | 2

1. Package Contents

Unzip (extract) the distribution zip file to a folder to see the contents.

1.1 Content Tree

• demo

•

auto_mode_4p.exe

• auto_mode_2p.exe

• semi_auto_mode_4p.exe

• semi_auto_mode_2p.exe

• develop

• doc

• examples

• silabs_pse

• install.bat

• silabs_pse-x.y.z-py3-none-any.whl

• silabs_pse-x.y.z.tar.gz

• firmware

• update_firmware.exe

• update_firmware.py

• si3474a_factory_combo_bl_firmware_image.c

• LICENCE.txt

• README.txt

1.2 Content Description

Content Description

demo Contains Windows executable files (.exe) which can be run without any Python

installation. See Section 3. Demos for descriptions of each demo.

develop Contains Python example source code, silabs_pse Python package, and soft-

ware documentation.

doc Contains documentation on the silabs_pse Python package. To view, open the

index.html file in a web browser (e.g., Chrome).

examples Python example source code, which has been compiled into the demo executa-

ble files. See Section 3. Demos for descriptions of each demo.

install.bat (Windows only) This batch script will install the silabs_pse Python package into

a Python interpreter using pip (https://packaging.python.org/key_projects/#pip).

silabs_pse This is the source code of the silabs_pse package which can be installed into a

Python interpreter.

silabs_pse-x.y.z-py3-none-any.whl This "wheel" file contains the silabs_pse package in binary format which can be

installed into a Python interpreter using pip (https://packaging.python.org/

key_projects/#pip). See Section 4.2.2 Install silabs_pse Package for installing

with Windows. See Section 5.1.2 Install silabs_pse Package for installing with

MacOS.

UG439: Si3474 Software User's Guide

Package Contents

silabs.com | Building a more connected world. Rev. 0.1 | 3

2. Hardware Configuration

To run the demos, connect the EVB in the configuration shown in Figure 2.1 Hardware Configuration for Demo (4P) on page 4. Use

the four-pair powered configuration shown in Figure 2.2 JP1-JP8 Configuration for Four-Pair Powered Operation on page 5 for de-

mos denoted with 4P. Use the two-pair powered configuration shown in Figure 2.4 JP1-JP8 Configuration for Two-Pair Powered Opera-

tion on page 6 for the demos denoted with 2P.

USB CABLE

DEPOPULATE

FOR HOSTED

OPERATION

POWERED DEVICE

+VPWR

SELECT 2P/4P

CONFIG

HOST

Figure 2.1. Hardware Configuration for Demo (4P)

UG439: Si3474 Software User's Guide

Hardware Configuration

silabs.com | Building a more connected world. Rev. 0.1 | 4

2.1 Configuring for 4P Operations

To configure

the EVB to power over four-pairs (802.3bt), configure the jumpers on the PoE-BT-CB as shown in Figure 2.2 JP1-JP8

Configuration for Four-Pair Powered Operation on page 5. This configuration should be used for all demos noted as 4P.

VOUT2

VOUT1

VOUT3

VOUT4

VOUT5

VOUT6

VOUT7

VOUT8

4P Configuration

BOT

TOP

VOUT1

VOUT2

VOUT3

VOUT4

VOUT5

VOUT6

VOUT7

VOUT8

Figure 2.2. JP1-JP8 Configuration for Four-Pair Powered Operation

Note that in the software distribution and demos, all ports and port pairs are indexed from zero. In 4P configuration, ports and port pairs

are numbered as shown in Figure 2.3 Mapping Between Hardware Indexing (from one) and Software Indexing (from zero) in 4P Config-

uration on page 5 below. Each port pair is made up of two ports.

VOUT1

VOUT2

VOUT3

VOUT4

VOUT5

VOUT6

VOUT7

VOUT8

PORT

PAIR 0

PORT

PAIR 1

PORT

PAIR 2

PORT

PAIR 3

PORT0

PORT1

PORT2

PORT3

PORT4

PORT5

PORT6

PORT7

HARDWARE

SOFTWARE

Figure 2.3. Mapping Between Hardware Indexing (from one) and Software Indexing (from zero) in 4P Configuration

UG439: Si3474 Software User's Guide

Hardware Configuration

silabs.com | Building a more connected world. Rev. 0.1 | 5

2.2 Configuring for 2P Operations

To configure

the EVB to power over two-pairs (802.3at), configure the jumpers on the PoE-BT-CB as shown in Figure 2.4 JP1-JP8

Configuration for Two-Pair Powered Operation on page 6. This configuration should be used for all demos noted as 2P.

VOUT1 VOUT3 VOUT5 VOUT7

BOT

TOP

VOUT1

VOUT2

VOUT3

VOUT4

VOUT5

VOUT6

VOUT7

VOUT8

VOUT2 VOUT4 VOUT6 VOUT8

2P Configuration

Figure 2.4. JP1-JP8 Configuration for Two-Pair Powered Operation

Note that in the software distribution and demos, all ports and port pairs are indexed from zero. In 2P configuration, ports are numbered

as shown in Figure 2.5 Mapping Between Hardware Indexing (from one) and Software Indexing (from zero) in 2P Configuration on page

VOUT1 VOUT3 VOUT5 VOUT7

VOUT2 VOUT4 VOUT6 VOUT8

PORT0 PORT2 PORT4 PORT6

PORT1 PORT3 PORT5 PORT7

HARDWARE

SOFTWARE

Figure 2.5. Mapping Between Hardware Indexing (from one) and Software Indexing (from zero) in 2P Configuration

UG439: Si3474 Software User's Guide

Hardware Configuration

silabs.com | Building a more connected world. Rev. 0.1 | 6

3. Demos

Demo source code is located in develop/examples.

3.1 Auto Mode (4P)

This demo configures the PSE into its fully autonomous mode which allows it to detect, classify, and power PDs without any host con-

trol. The PSE is configured to provide power over four pairs with 90W allocation per port pair. The screen will continuously display the

detection, classification, and power consumption information for all ports.

PSE Temperature: 31.51 C

VPWR Voltage: 55.9 V

Port 0 Detect: VALID CC_SINGLE_SIG Requested: CLASS_7_4P_SS Assigned: CLASS_7_4P_SS Power: 0.58W

Port 1 Detect: VALID CC_SINGLE_SIG Requested: CLASS_7_4P_SS Assigned: CLASS_7_4P_SS Power: 0.57W

Port 2 Detect: OPEN_CIRCUIT

Port 3 Detect: OPEN_CIRCUIT

Port 4 Detect: VALID CC_SINGLE_SIG Requested: CLASS_8_4P_SS Assigned: CLASS_8_4P_SS Power: 4.32W

Port 5 Detect: VALID CC_SINGLE_SIG Requested: CLASS_8_4P_SS Assigned: CLASS_8_4P_SS Power: 5.17W

Port 6 Detect: VALID CC_SINGLE_SIG Requested: CLASS_4 Assigned: CLASS_4 Power: 0.23W

Port 7 Detect: VALID CC_SINGLE_SIG Requested: CLASS_4 Assigned: CLASS_4 Power: 0.19W

In this

example, there are 3 different four-pair powered devices connected to the EVB. The detection, requested class, assigned class,

and power consumption of each PD is displayed and updated in real time. The port pair with no PD attached displays the detection

status of OPEN_CIRCUIT for both ports, indicating that no load has been detected. Detection is continuously performed on these ports,

and the screen will be updated upon detecting a PD.

3.2 Auto Mode (2P)

Note: The PoE-BT-CB jumper settings must be configured to support 2-pair powering for this demo to work as intended. See Section

2.2 Configuring for 2P Operations for configuring the jumper settings to 2-pair powered ports.

This demo is identical to the Section 3.1 Auto Mode (4P) demo, except the PSE is configured to provide power over two pairs with 30W

power allocation per port. This allows powering up to 8 different PDs (each up to 30W) at once.

PSE Temperature: 30.86 C

VPWR Voltage: 55.9 V

Port 0 Detect: VALID Requested: CLASS_2 Assigned: CLASS_2 Power: 1.14W

Port 1 Detect: VALID Requested: CLASS_3 Assigned: CLASS_3 Power: 6.30W

Port 2 Detect: OPEN_CIRCUIT

Port 3 Detect: VALID Requested: CLASS_3 Assigned: CLASS_3 Power: 6.38W

Port 4 Detect: OPEN_CIRCUIT

Port 5 Detect: OPEN_CIRCUIT

Port 6 Detect: VALID Requested: CLASS_4 Assigned: CLASS_4 Power: 0.43W

Port 7 Detect: OPEN_CIRCUIT

In this

example, there are 4 different two-pair powered devices connected to the EVB. The detection, requested class, assigned class,

and power consumption of each PD is displayed and updated in real time. The ports with no PD attached display the detection status of

OPEN_CIRCUIT, indicating that no load has been detected. Detection is continuously performed on these ports, and the screen will be

updated upon detecting a PD.

UG439: Si3474 Software User's Guide

Demos

silabs.com | Building a more connected world. Rev. 0.1 | 7

3.3 Semi-Auto Mode (4P)

This demo

configures the PSE into its semi-autonomous mode which allows it to detect and classify PDs without host control, and relies

on a host to power PDs. The demo code functions as the host, and will close the loop with the PSE to react to events and send push-

button commands for powering PDs. The screen will display all events received by the host from the PSE and actions taken by the

host.

I2C 0x20 REG POWER_ALLOCATION 0x29 = 0xff

I2C 0x21 REG POWER_ALLOCATION 0x29 = 0xff

I2C 0x20 REG PORT_REMAP 0x26 = 0xe4

I2C 0x21 REG PORT_REMAP 0x26 = 0xe4

I2C 0x20 REG MISC 0x17 = 0x8c

I2C 0x21 REG MISC 0x17 = 0x8c

I2C 0x20 REG PORT_MODE 0x12 = 0xaa

I2C 0x21 REG PORT_MODE 0x12 = 0xaa

I2C 0x20 REG DETECT_CLASS_ENABLE 0x14 = 0xff

I2C 0x21 REG DETECT_CLASS_ENABLE 0x14 = 0xff

I2C 0x20 REG INTERRUPT 0x00 = 0x80

I2C 0x20 REG SUPPLY_EVENT_COR 0x0b = 0x30

I2C 0x21 REG INTERRUPT 0x00 = 0x80

I2C 0x21 REG SUPPLY_EVENT_COR 0x0b = 0x30

I2C 0x20 REG INTERRUPT 0x00 = 0x08

I2C 0x20 PORT 0 DETECT DONE: STATUS: VALID - CC_SINGLE_SIG

I2C 0x20 PORT 1 DETECT DONE: STATUS: VALID - CC_SINGLE_SIG

I2C 0x20 REG INTERRUPT 0x00 = 0x10

I2C 0x20 PORT 0 CLASS DONE: STATUS: CLASS_8_4P_SS

I2C 0x20 SENDING PUSH-BUTTON ON TO PORT PAIR 0

I2C 0x20 PORT 1 CLASS DONE: STATUS: CLASS_8_4P_SS

I2C 0x20 REG INTERRUPT 0x00 = 0x08

I2C 0x20 PORT 0 DETECT DONE: STATUS: VALID - CC_SINGLE_SIG

I2C 0x20 PORT 1 DETECT DONE: STATUS: VALID - CC_SINGLE_SIG

I2C 0x20 REG INTERRUPT 0x00 = 0x10

I2C 0x20 PORT 0 CLASS DONE: STATUS: CLASS_8_4P_SS

I2C 0x20 PORT 1 CLASS DONE: STATUS: CLASS_8_4P_SS

I2C 0x20 REG INTERRUPT 0x00 = 0x01

I2C 0x20 REG POWER_EVENT_COR 0x03 = 0x03

I2C 0x20 REG INTERRUPT 0x00 = 0x02

I2C 0x20 REG POWER_EVENT_COR 0x03 = 0x30

I2C 0x20 REG INTERRUPT 0x00 = 0x07

I2C 0x20 REG POWER_EVENT_COR 0x03 = 0x33

I2C 0x20 REG DISCONNECT_PCUT_FAULT_COR 0x07 = 0x30

The semi-auto demo always begins with initialization. The PSE is first configured to four-pair powering with a power allocation of 90W

per port pair, as shown in the POWER_ALLOCATION register. Next, the port remap is written to its default value, which is a one-to-one

map between logical and physical ports. The MISC register is configured to enable the interrupt pin, detect change, and class change

bits. All ports are configured into semi-autonomous mode, as shown in the PORT_MODE register. Finally, detection and classification

are enabled for all ports, as shown in the DETECT_CLASS_ENABLE register.

After initialization, interrupts and events are handled. The PSE always has a UVLO event upon boot-up, as shown in the INTERRUPT

and SUPPLY_EVENT registers. After reading the supply event clear-on-read (COR) register, these events are cleared and no further

SUPPLY_EVENT interrupts are received.

In this example, the user plugs in a PD to the EVB. After plugging in the PD, the first interrupt received and printed to screen is a DE-

TECT_CC_DONE interrupt. The interrupt is handled by reading the CLASS_DETECT_EVENT register, which indicates that detection

and connection check have been completed on ports 0 and 1. Next, the CLASS_DETECT_STATUS and AUTOCLASS_CONNEC-

TION_CHECK registers are read for the associated ports, and the results are printed to the screen. In this example, it is shown that a

load was detected with a valid detection status and connection check result of single signature for both ports.

The next interrupt received and printed to screen is a CLASS_DONE interrupt. The interrupt is handled by reading the CLASS_DE-

TECT_EVENT register, which indicates that classification has been completed on port 0. Next, the CLASS_DETECT_STATUS register

is read for the associated port, and the results are printed to the screen. In this example, it is shown that the connected load was classi-

fied as requesting class 8 power.

Upon receiving valid detection and classification events, the demo code powers the PD by writing to the push-button register PB_POW-

ER_ENABLE for the associated port pair. The PSE receives the push-button power on command and performs detection and classifica-

tion again before applying power to the PD. As shown in the print statements, the detection and classification interrupts and results are

identical to before. After classification, the next interrupt received is a POWER_ENABLE_CHANGE event. This event is handled by

reading the POWER_EVENT register, which shows that power has been enabled for ports 0 and 1. Power enabled indicates that the

ports have been turned on and the PD is in the inrush phase of power-up. The next interrupt received is a POWER_GOOD_CHANGE

UG439: Si3474 Software User's Guide

Demos

silabs.com | Building a more connected world. Rev. 0.1 | 8

event. This event is handled by reading the POWER_EVENT register, which shows that the power status of ports 0 and 1 is now

POWER_GOOD. This indicates that the PD has exited inrush and power has been successfully applied to the PD.

Finally, the

user unplugs the PD from the EVB. The interrupts DISCONNECT, POWER_ENABLE_CHANGE, and POW-

ER_GOOD_CHANGE are received simultaneously. The POWER_ENABLE_CHANGE and POWER_GOOD_CHANGE interrupts are

handled by reading the POWER_EVENT register, which shows that power status has changed for ports 0 and 1. The DISCONNECT

interrupt is handled by reading the DISCONNECT_PCUT_FAULT register, which shows that a disconnection event has occurred for

ports 0 and 1.

The PSE has successfully powered a PD and then removed power upon detecting that the PD has been disconnected.

UG439: Si3474 Software User's Guide

Demos

silabs.com | Building a more connected world. Rev. 0.1 | 9

3.4 Semi-Auto Mode (2P)

Note: The PoE-BT-CB

jumper settings must be configured to support 2-pair powering for this demo to work as intended. See Section

2.2 Configuring for 2P Operations for configuring the jumper settings to 2-pair powered ports.

This demo is identical to the Section 3.3 Semi-Auto Mode (4P) demo, except the PSE is configured to provide power over two pairs with

30W power allocation per port. This allows powering up to 8 different PDs (each up to 30W) at once.

I2C 0x20 REG POWER_ALLOCATION 0x29 = 0x33

I2C 0x21 REG POWER_ALLOCATION 0x29 = 0x33

I2C 0x20 REG PORT_REMAP 0x26 = 0xe4

I2C 0x21 REG PORT_REMAP 0x26 = 0xe4

I2C 0x20 REG MISC 0x17 = 0x8c

I2C 0x21 REG MISC 0x17 = 0x8c

I2C 0x20 REG PORT_MODE 0x12 = 0xaa

I2C 0x21 REG PORT_MODE 0x12 = 0xaa

I2C 0x20 REG DETECT_CLASS_ENABLE 0x14 = 0xff

I2C 0x21 REG DETECT_CLASS_ENABLE 0x14 = 0xff

I2C 0x20 REG SUPPLY_EVENT_COR 0x0b = 0x30

I2C 0x21 REG SUPPLY_EVENT_COR 0x0b = 0x30

I2C 0x20 PORT 0 DETECT DONE: STATUS: VALID

I2C 0x20 PORT 0 CLASS DONE - STATUS: CLASS_4

I2C 0x20 SENDING PUSH-BUTTON ON TO PORT 0

I2C 0x20 PORT 0 DETECT DONE: STATUS: VALID

I2C 0x20 PORT 0 CLASS DONE - STATUS: CLASS_4

I2C 0x20 REG POWER_EVENT_COR 0x03 = 0x01

I2C 0x20 REG POWER_EVENT_COR 0x03 = 0x10

I2C 0x20 REG POWER_EVENT_COR 0x03 = 0x11

I2C 0x20 REG DISCONNECT_PCUT_FAULT_COR 0x07 = 0x10

As with the 4P demo, the semi-auto demo always begins with initialization. The PSE is first configured to two-pair powering with a pow-

er allocation of 30W per port, as shown in the POWER_ALLOCATION register. Next, the port remap is written to its default value, which

is a one-to-one map between logical and physical ports. The MISC register is configured to enable the interrupt pin, detect change, and

class change bits. All ports are configured into semi-autonomous mode, as shown in the PORT_MODE register. Finally, detection and

classification are enabled for all ports, as shown in the DETECT_CLASS_ENABLE register.

After initialization, interrupts and events are handled. The PSE always has a UVLO event upon boot-up, as shown in the SUP-

PLY_EVENT register. After reading the supply event clear-on-read (COR) register, these events are cleared and no further SUP-

PLY_EVENT interrupts are received.

In this example, the user plugs in a PD to the EVB. After plugging in the PD, the first interrupt received is a DETECT_CC_DONE inter-

rupt. The interrupt is handled by reading the CLASS_DETECT_EVENT register, which indicates that detection has been completed on

port 0. Next, the CLASS_DETECT_STATUS register is read for the associated port, and the results are printed to the screen. In this

example, it is shown that a load was detected with a valid detection status on port 0. Note that because the port is configured for two-

pair powering, no connection check is performed.

The next interrupt received is a CLASS_DONE interrupt. The interrupt is handled by reading the CLASS_DETECT_EVENT register,

which indicates that classification has been completed on port 0. Next, the CLASS_DETECT_STATUS register is read for the associ-

ated port, and the results are printed to the screen. In this example, it is shown that the connected load was classified as requesting

class 4 power.

Upon receiving valid detection and classification events, the demo code powers the PD by writing to the push-button register PB_POW-

ER_ENABLE for the associated port. The PSE receives the push-button power on command and performs detection and classification

again before applying power to the PD. As shown in the print statements, the detection and classification results are identical to before.

After classification, the next interrupt received is a POWER_ENABLE_CHANGE event. This event is handled by reading the POW-

ER_EVENT register, which shows that power has been enabled for port 0. Power enabled indicates that the port has been turned on

and the PD is in the inrush phase of power-up. The next interrupt received is a POWER_GOOD_CHANGE event. This event is handled

by reading the POWER_EVENT register, which shows that the power status of port 0 is now POWER_GOOD. This indicates that the

PD has exited inrush and power has been successfully applied to the PD.

Finally, the user unplugs the PD from the EVB. The interrupts DISCONNECT, POWER_ENABLE_CHANGE, and POW-

ER_GOOD_CHANGE are received simultaneously. The POWER_ENABLE_CHANGE and POWER_GOOD_CHANGE interrupts are

handled by reading the POWER_EVENT register, which shows that power status has changed for ports 0 and 1. The DISCONNECT

interrupt is handled by reading the DISCONNECT_PCUT_FAULT register, which shows that a disconnection event has occurred for

port 0.

The PSE has successfully powered a PD and then removed power upon detecting that the PD has been disconnected.

UG439: Si3474 Software User's Guide

Demos

silabs.com | Building a more connected world. Rev. 0.1 | 10

4. Windows

4.1 Run Demo Scripts

No installation is necessary to run the demos on Windows. Navigate to the demo folder and run the .exe files directly. The source code

of the demos can be found in the develop/examples directory. To run manually, see Section 4.3 Run Demo Scripts Manually.

4.2 Installation

Note: No installation is required to run the demos on Windows. See Section 4.1 Run Demo Scripts.

4.2.1 Install Python

Python must already be installed to use the silabs_pse package and run the example scripts using the Python interpreter. Download

and install Python 3 from the Python website: https://www.python.org/downloads/

4.2.2 Install silabs_pse Package

The install.bat file in the develop directory will complete this step automatically. To run, simply double-click it.

Otherwise, use pip to install the silabs_pse Python package into a Python interpreter using the .whl file included in the distribution. Navi-

gate to the develop directory in the distribution in a shell or CMD window and execute the following command (replace x.y.z with the

appropriate version included in the distribution):

pip install silabs_pse-x.y.z-py3-none-any.whl

4.3 Run Demo Scripts Manually

First,

make

sure Python and the silabs_pse package are installed following the Section 4.2 Installation steps. The demo scripts can be

run directly using the Python Interpreter. Navigate to the develop directory in the distribution in a shell or CMD window and execute the

following command, replacing the script with the desired demo script.

python auto_mode_4p.py

The script should run and display in the console window.

Note: Integrated Development

Environments (IDE) can be useful for developing and running code in a single window. PyCharm is a

popular choice for Python development

4.4 Write Custom Scripts

Custom scripts can be written and executed directly using the Python interpreter like the demo scripts. See the silabs_pse API docu-

mentation in develop/doc for programmer resources.

UG439: Si3474 Software User's Guide

Windows

silabs.com | Building a more connected world. Rev. 0.1 | 11

5. MacOS

5.1 Installation

5.1.1 Install Python

Python must already be installed to use the silabs_pse package and run the example scripts. Download and install Python 3 from the

Python website: https://www.python.org/downloads/

5.1.2 Install silabs_pse Package

Use pip to install the Python package into a Python interpreter using the .whl file included in the distribution. In terminal, navigate to the

develop directory of the distribution and execute the following command (replace x.y.z with the appropriate version included in the dis-

tribution):

pip install silabs_pse-x.y.z-py3-none-any.whl

5.2 Run Demo Scripts

After installation,

in terminal navigate to the develop/examples directory and run the following command, pointing to the desired exam-

ple script:

python auto_mode_4p.py

The script should run and display in the console window.

5.3 Write Custom Scripts

Custom scripts

can be written and executed in Python like the demo scripts. See the silabs_pse API documentation in develop/doc for

programmer resources.

UG439: Si3474 Software User's Guide

MacOS

silabs.com | Building a more connected world. Rev. 0.1 | 12

Smart.

Connected.

Energy-Friendly.

Products

www.silabs.com/products

Quality

www.silabs.com/quality

Support and Community

community.silabs.com

http://www.silabs.com

Silicon Laboratories Inc.

400 West Cesar Chavez

Austin, TX 78701

USA

Disclaimer

Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or

intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical"

parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes without

further notice to the product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Without prior

notification, Silicon Labs may update product firmware during the manufacturing process for security or reliability reasons. Such changes will not alter the specifications or the performance

of the product. Silicon Labs shall have no liability for the consequences of use of the information supplied in this document. This document does not imply or expressly grant any license

to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any FDA Class III devices, applications for which FDA premarket approval is

required, or Life Support Systems without the specific written consent of Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or health,

which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs

products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering

such weapons. Silicon Labs disclaims all express and implied warranties and shall not be responsible or liable for any injuries or damages related to use of a Silicon Labs product in such

unauthorized applications.

Trademark Information

Silicon Laboratories Inc.®, Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, ClockBuilder®, CMEMS®, DSPLL®, EFM®, EFM32®,

EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®,

Gecko OS, Gecko OS Studio, ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® , Zentri, the Zentri logo and Zentri DMS, Z-

Wave®, and others are trademarks or registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a

registered trademark of ARM Limited. Wi-Fi is a registered trademark of the Wi-Fi Alliance. All other products or brand names mentioned herein are trademarks of their respective holders.

Silicon Labs UG439 User guide

Silicon Labs UG439 User guide

Silicon Labs UG439 User guide

Related papers

Other documents