Fire Magic Echelon Diamond Built-In Grill User manual

Brand: Fire Magic

Model: Echelon Diamond Built-In Grill

Category: Barbecues & grills

Type: User manual

IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.

OUTDOOR BUILT-IN GAS GRILL

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

WARNINGS AND SAFETY CODES

DANGER:

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂ ame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or the ﬁ re department.

WARNING:

1. Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

CODE AND SUPPLY REQUIREMENTS: This grill

must be installed in accordance with local codes

and ordinances, or, in the absence of local codes,

with the latest National Fuel Gas Code (ANSI

Z223.1/NFPA 54), or Natural Gas and Propane

Storage and Handling Installation Code (CSA-

B149.1).

This appliance and its dedicated manual shutoff

valve must be disconnected from the gas-supply

piping system when testing the system at pressures

in excess of ½ psig (3.5 kPa).

This appliance must be isolated from the gas-

supply piping system by closing its dedicated

manual shutoff valve during any pressure testing

of the gas-supply system at pressures up to and

including ½ psig (3.5 kPa).

All electrical outlets in the vicinity of the grill must

be properly grounded in accordance with local

codes, or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70, or the

Canadian Electrical Code, CSA C22.1, whichever

is applicable.

Keep all electrical-supply cords and fuel-supply

hoses away from any heated surface.

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

WARNING:

Improper installation, adjustment, alteration,

service, or maintenance can cause injury

or property damage. For proper installation,

refer to the installation instructions. For

assistance or additional information,

consult a qualiﬁ ed professional installer,

service agency, or the gas supplier.

E660i, E790i, and E1060i

Certiﬁ ed to: ANSI Z21.58b-2012

CSA 1.6b-2012

10-32

Proper operation of your grill requires

prompt and periodic maintenance.

See the CARE & CLEANING section

for details.

REV 5 - 1412081445

L-C2-329

ECHELON

diamond series

E790i shown

Page is loading ...

CONTENTS

REV 5 - 1412081445

L-C2-329

4 REPLACEMENT PARTS LIST

7 COUNTERTOP OVERHANG

7 MODEL SPECIFICATIONS

8 SUBSTRATE

8 BUILT-IN GRILL DIMENSIONS TABLE

9 BUILT-IN GRILL WIRING DIAGRAM

10 ELECTRICAL CONNECTIONS

10 GRILL MAINTENANCE AND SAFETY INFORMATION

10 MASTER SWITCH

11 INSTALLATION REQUIREMENTS

12 ENSURE PROPER COMBUSTION AIR AND COOLING AIRFLOW

12 EXHAUST REMOVAL

12 GAS-SUPPLY PLUMBING REQUIREMENTS

13 NATURAL GAS INSTALLS

13 PROPANE GAS INSTALLS (HOUSEHOLD & CYLINDER)

13 WHEN A PROPANE CYLINDER IS USED

13 ENCLOSURE REQUIREMENTS

14 COUNTER PREPARATION

14 CONNECT THE GAS SUPPLY

14 INSTALLATION

15 INSTALL ZONE DIVIDERS

16 ELECTRICAL INSTALLATION

17 SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

19 IDENTIFICATION OF GRILL CONTROLS

20 OPTIONAL POWER HOOD

21 LIGHTING (IGNITION) INSTRUCTIONS

21 SHUTTING OFF THE UNIT

23 DIGITAL THERMOMETER / INTERIOR AND KNOB LIGHTS

26 ROTISSERIE INSTRUCTIONS

27 INFRARED BURNER OPERATION

28 GRILLING TIPS

29 ACCESSORIES

30 FIRE MAGIC

DRIP TRAY

31 CARE & CLEANING

32 REPLACING HALOGEN BULBS

33 POWER SUPPLY FUSE REPLACEMENT

34 REGULATOR CONVERSION

34 GAS ORIFICE CONVERSION

34 CONVERTING THE GAS TYPE

37 BURNER AIR SHUTTER ADJUSTMENT

38 CONTROL PANEL REMOVAL

39 TROUBLESHOOTING

40 WARRANTY

REPLACEMENT PARTS LIST

To order replacement

parts, contact your

local Fire Magic

dealer.

Items in light gray are

not available on all

models.

Some items shown

are optional, or are

not available for

certain models. Your

model may vary, refer

to parts list.

REV 5 - 1412081445

L-C2-329

Fig. 4-1

REPLACEMENT PARTS LIST (Cont.)

REV 5 - 1412081445

L-C2-329

E660i E790i E1060i

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

Stainless cooking grid (set of 2 or 3) 3544-S-3 1 3539-S-3 1 23539-S-2 2

Flavor grid (set of 3 or 4) 3057-S-3 1 3056-S-3 1 3056-S-4 1

Main burner 3041-50 3 3041-50 3 3041-50 4

Heatshield kit 24177-05 3 24177-05 3 24177-05 4

Silicone gasket 24177-06 3 24177-06 3 24177-06 4

Infrared burner * 3050 1 3050 1 3050 1

Oven lid 23738-53 1 23745-53 1 23747-53 1

Oven lid w/ window 24193-54 1 24188-54 1 24183-54 1

Window (only) *‡ 24187-45 1 24187-45 1 24187-45 1

Warming rack 36735-M 1 36755-M 1 36745-M 1

10.

Back burner assembly 24794-02 1 24789-02 1 24784-02R/L 1

11.

Back burner cover 24794-010 1 24789-010 1 24784-010 2

12.

Zone separator 3061-S 2 3061-S 2 3061-S 3

13.

Heavy-duty rotisserie motor 3600-05M 1 3600-05M 1 3600-05M 1

14.

Heavy-duty rod 3606-40 1 3609-40 1 3607-40 1

15.

Heavy-duty rod knob 24187-16 1 24187-16 1 24187-16 1

16.

Meat holder (pair) 3613 1 3613 1 3613 1

17.

Counterbalance 3620E 1 3620E 1 3620E 1

18.

Grid lifter 3519 1 3519 1 3519 1

19.

Convertible regulator PR-4 1 PR-4 1 PR-4 1

20.

Valve manifold w/ back burner 24193-22 1 24188-22 1 24183-22 1

21.

Control panel w/ back burner and raceway † 24194-10 1 24189-10 1 24184-10 1

Control panel w/ back burner, raceway, and

wire harness †

24194-12 1 24189-12 1 24184-12 1

22.

Small knob 24182-42 1 24182-42 1 24182-42 2

23.

Large knob 24182-41 3 24182-41 3 24182-41 4

24.

LED disk (small) 24182-64 1 24182-64 1 24182-64 2

25.

LED disk (large) 24182-63 3 24182-63 3 24182-63 4

26.

Digital thermometer 24182-12 1 24182-12 1 24182-12 1

27.

Meat probe 24187-14S 1 24187-14S 1 24187-14S 1

28.

Power supply w/ connector † 24187-18 1 24187-18 1 24187-18 1

* If equipped

‡ Not shown

† Add (M) to part number for power hood

REPLACEMENT PARTS LIST (Cont.)

REV 5 - 1412081445

L-C2-329

E660i E790i E1060i

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

29.

Drip tray 3087 1 3087 1 3087 1

30.

Drip tray liner (set of 4) 3557 1 3557 1 3557 1

31.

Wire harness for raceway ‡ 24194-47 1 24189-47 1 24184-47 1

32.

Back burner electrode *‡ 4199-52 1 4199-52 1 4199-52 2

33.

Electrode ‡ 3199-72 3 3199-72 3 3199-72 4

34.

Thermometer wire harness ‡ 24187-13 1 24187-13 1 24187-13 1

35.

Natural gas oriﬁ ce(s) ‡ 3001-42-3 1 3001-38-3 1 3001-40-4 1

36.

Natural back burner gas oriﬁ ce(s) ‡ 3001-53-1 1 3001-51-1 1 3001-53-2 1

37.

Propane gas oriﬁ ce(s) ‡ 3001-54-3 1 3001-53-3 1 3001-53-4 1

38.

Propane back burner gas oriﬁ ce(s) ‡ 3001-63-1 1 3001-57-1 1 3001-63-2 1

39.

Natural smoker oriﬁ ce ‡ 3003-68-1 1 3003-68-1 1 3003-68-1 1

40.

Propane smoker oriﬁ ce ‡ 3003-77-1 1 3003-77-1 1 3003-77-1 1

41.

Wood chip box assembly 24182-45 1 24182-45 1 24182-45 1

42.

12V / 10 watt halogen light bulb ‡ 24187-15 2 24187-15 2 24187-15 3

43.

Light lens ‡ 24187-26 2 24187-26 2 24187-26 3

44.

Lamp assembly ‡ 24187-28 2 24187-28 2 24187-28 3

45.

Power hood motor assembly * 24183-18 1 24183-18 1 24183-18 1

46.

Power hood rocker switch* 24187-39 1 24187-39 1 24187-39 1

47.

Lighted master shut-off switch 24182-46 1 24182-46 1 24182-46 1

48.

Light microswitch 24187-20 1 24187-20 1 24187-20 1

Power hood light & motor microswitch 24187-44 1 24187-44 1 24187-44 1

49.

Flash tube (left) ‡ 24187-29 1 24187-29 1 24187-29 1

50.

Flash tube (right) ‡ 24187-35 2 24187-35 2 24187-35 3

51.

Flex connector ‡ 3030-08 1 3030-08 1 3030-08 1

52.

Support screw (set of 2) 24182-47 1 24182-47 1 24182-47 1

53.

Fire Magic

cookbook ‡ 3595 1 3595 1 3595 1

54.

Wire harness extension 24182-53 1 24182-53 1 24182-53 1

* If equipped

‡ Not shown

COUNTERTOP OVERHANG

The control panel is designed to sit ﬂ ush against the enclosure front wall. If the non-combustible enclosure countertop extends

beyond the front wall, creating a countertop overhang, it must be cut ﬂ ush with the front wall for the width of the control panel or

a gap will be created exposing the forward portions of the left and right side grill ﬁ re walls. See illustrations above.

MODEL SPECIFICATIONS

Important: FOR YOUR SAFETY, you must provide openings in the island enclosure for drainage, replacement air, and

cross-ventilation of any storage area exposed to possible leakage from gas connections, the unit, or propane

tanks. See the ENCLOSURE REQUIREMENTS section for details.

▲

If equipped

* Note: If installing this grill in a combustible enclosure, the correct insulating liner must be used. Consult liner instructions for

counter cut-out dimensions and installation.

†

Includes any substrate at front wall of enclosure (in the area the rear of the control panel is to sit ﬂ ush against). See SUBSTRATE

section on next page.

‡

Only applicable for non-combustible enclosures that have countertops with an overhang (see illustration and section below).

TOP VIEW

Countertop

Lower support

Countertop

overhang

Control panel

NON-COMBUSTIBLE

ENCLOSURE CUT-OUT

DIMENSIONS

Fig. 7-1

FRONT VIEW

Extra cut-out

for Power

Hood only!

" x 10"

11"

See next page

for substrate

considerations

Countertop

overhang

TOP VIEW

SIDE VIEW

Countertop

overhang

(Control

panel)

(Countertop)

Clearance

(Overhang)

/8"

Y= Total

Countertop

Overhang

Control

panel

Check clearance for

control panel removal

MODEL SPECIFICATIONS TABLE

Table 1

E660i E790i E1060i

Main burner quantity

N/P oriﬁ ce drill size

#42 / #54

#38 / #53

#40 / #53

Back burner quantity

N/P oriﬁ ce drill size

#53 / #63

#51 / #57

#53 / #63

Smoker drawer burner

N/P oriﬁ ce drill size

#68 / #77 #68 / #77 #68 / #77

Infrared searing burner

▲

N/P oriﬁ ce drill size

#45 / #55 #45 / #55 #45 / #55

Echelon insulating liner model # (not included)* 3176-50 3186-50 3185-50

Power Supply Rating

120VAC / 1.5A / 60 Hz

Oven Lights Rating

12V / 10 watt halogen light bulb

A Countertop to unit bottom cut-out* 12" 12" 12"

B Side to side non-combustible cut-out* 31-

/4" 37" 50"

C Front to back non-combustible cut-out*† 23-

/2" 23-

/2"

D Control panel width non-combustible cut-out‡ 33" 38-

/4" 51-

/4"

REV 5 - 1412081445

L-C2-329

Model

Height Width Depth

(Top to bottom) (Left to right) (Front to

back)

Upper hanger to top

(with oven)

Hanger to

hanger

(G)

Control

panel

width

(H)

Maximum

depth

(I)

Open

(E)

Closed

(F)

E660i

23-

" 15" 36-

" 32-

" 29-

E790i

23-

" 15" 42" 38-

" 29-

E1060i

23-

" 15" 54-

" 51-

" 29-

MODEL SPECIFICATIONS (cont.)

BUILT-IN GRILL DIMENSIONS TABLE

Fig. 8-3

SUBSTRATE

When adding any substrate to the enclosure front wall (including tiles, stone, etc.), consider the following:

Substrate Behind Control Panel

Substrate Alongside Control Panel

Flush

(Control panel)

(Countertop)

(Control panel)

Substrate

(includes tiles,

etc. at front of

enclosure)

Countertop

overhang

(if applicable)

Flush

Grill liner

Substrate

(includes tiles,

etc. at front of

enclosure)

Clearance

Any additional substrate alongside the control panel

does not need to be considered in Dim. C (see previous

page), however a

/4" clearance on each side (same as

overhang) and below is required.

Substrate

countertop "front to back" cutout

must equate to Dim. C (see previous page)

when the substrate sits ﬂ ush behind the

control panel.

Fig. 8-1 Fig. 8-2

Countertop

overhang

(if applicable)

Clearance

TOP VIEW TOP VIEW

REV 5 - 1412081445

L-C2-329

MODEL SPECIFICATIONS (cont.)

Note: In addition, a wire diagram speciﬁ c to your unit

can be found afﬁ xed to the inside of the control

panel.

BUILT-IN GRILL WIRING DIAGRAM*

E1060i model shown. Model wire diagrams may vary.

REV 5 - 1412081445

L-C2-329

Power supply

Wire harness

extension

Wire harness

assembly

Valve

manifold

Master

switch

Main burner igniters

Backburner

igniter

Left oven

light

Digital

thermometer

Oven light

micro switch

(not used for

Magic View)

Meat

probe

jack

Thermocouple

Back

burner

Main

burner 1

Main

burner 2

Main

burner 3

Center oven

light

Right oven

light

Backburner

igniter

Smoker

igniter

For Magic

View only

Ground

Wire

Main

burner 4

Smoker

burner

Back

burner

LED disc

(small)

LED disc

(large)

Thermometer

wire harness

ELECTRICAL CONNECTIONS

This grill requires 120VAC power to operate.

Plug the power supply cord into a properly

wired and inspected GFCI electrical

receptacle (15 AMP minimum). Use a heavy-

duty grounded extension cord if necessary.

WARNING

Electrical Grounding Instructions

For your protection against shock hazard, this

outdoor-cooking gas-appliance is equipped with

a three-pronged (grounding) electrical connector.

This appliance should be connected to a properly

grounded three-prong receptacle using a grounding

extension cord rated for outdoor use. Do not cut or

remove the grounding prong from the connector.

Important: ONLY REPLACE THE OVEN LIGHTS

WITH 12V / 10 WATT HALOGEN BULB(S).

1. The outdoor grill and surrounding area MUST

remain clear of ﬂ ammable substances such as

gasoline, yard debris, wood, etc.

2. The airﬂ ow through the vent space located below

the control panel must remain unobstructed.

3. When using propane gas:

a. The required ventilation openings in the

enclosure must be clear of debris.

b. The propane cylinder, regulator, and rubber

hose must be in a location not subject to

temperature above 125° F (51° C).

4. The ﬂ ames on each burner burn evenly along

the entire burner with a steady ﬂ ame (mostly

blue). If burner ﬂ ames are not normal, check

and clean the oriﬁ ce and burner/venturi tubes

for insects and insect nests. A clogged tube can

lead to a ﬁ re beneath the grill. A proper ﬂ ame

pattern will ensure safe operation and optimal

performance. Adjust the air shutter as needed

(see AIR SHUTTER ADJUSTMENT).

5. The in-line gas valve or gas cylinder valve must

always be shut OFF when the grill is not in use.

6. The drip collector holes must be clear and

unobstructed. Excessive grease deposits can

result in a grease ﬁ re.

7. The back burner or IR burner cover must be

removed before using the burner.

8. Whenever reconnecting any wires, apply a

small amount of dielectric grease to the male

connector, then make the connection.

GRILL MAINTENANCE AND SAFETY INFORMATION

WARNING: NEVER cover the entire cooking or grill surface with griddles or pans. Overheating will occur, and

burners will not perform properly when combustion heat is trapped below the cooking surface.

CAUTION: NEVER spray water on a hot gas unit.

The grill serial identiﬁ cation number is located on the underside of the drip tray handle. It

is recommended that the drip tray ﬁ rst be removed and cleaned / emptied of its contents,

then turned over to view. The unit rating label is located inside of the control panel.

REV 5 - 1412081445

L-C2-329

MASTER SWITCH

The master switch is push button operated, and is

located on the right side of the control panel (see

Fig. 10-1). It controls the power to all lights, igniters,

and the thermometer. It allows the power to be

turned on or off for safety and convenience. The

switch will need to be turned on prior to each grill

use, and turned off after each use.

Master

switch

Fig. 10-1

INSTALLATION REQUIREMENTS

Installation must be performed by a qualiﬁ ed professional service

technician.

This grill is designed for outdoor use only. DO NOT use this grill inside

a building, garage, enclosed area, or under an unprotected overhead

combustible construction.

See below and the EXHAUST REMOVAL section on the following

page for details on installing under overhead construction.

DO NOT use this grill in or on a recreational vehicle or boat.

Important: If installing this grill in a combustible surround, the correct

RHP insulating liner must be used.

Important: Refer to the information below to ensure all required

clearances are met.

The grill must have a minimum clearance of 18" from combustible

materials/items AT ALL TIMES.

Overhead Construction Requirements (if applicable)

Non-combustible overhead construction: A 6 foot clearance is required

between the countertop and the construction above (Fig. 11-1).

Combustible overhead construction: A 6 foot clearance is required

between the countertop and the construction above. A vent hood

(see EXHAUST REMOVAL section) or an RHP combustible overhead

protection kit is required directly above the grill. See Fig. 11-1. RHP

vent hoods and protection kits are available, contact your local

dealer.

Side and Rear Wall Clearances

For the minimum clearances between the grill and any side or rear

walls, your setup must fall within one (or more) of the following:

A. Clearance between grill and strictly non-combustible wall

(i.e. brick wall, see Fig. 11-2)

• The grill must have a minimum of 4" right, left, and rear

clearance from any non-combustible wall.

(To allow for proper ventilation and prevent dangerous

overheating.)

B. Clearance between grill and a protected combustible wall

(i.e. a non-combustible wall in front of a combustible wall to serve

as a barrier. This can be accomplished by brick, or a metal stud

ﬁ nished with non-combustible substrate, see Fig. 11-3)

• The grill must have a minimum of 14" right, left, and rear

clearance from the protected combustible wall.

(The 4" non-combustible material plus an additional 10"

clearance between the grill and protected wall.)

C. Clearance between grill and combustible wall

• The grill must have a minimum of 18" right, left, and rear

clearance from any combustible wall (see Fig. 11-4).

Backsplash Clearance (if applicable)

If a non-combustible backsplash exists, it must have a minimum of a

4" clearance from the rear of the grill (to allow for proper ventilation

and prevent dangerous overheating). See Fig. 11-5.

Important: This 4" backsplash clearance must ﬁ rst be met prior to

any non-combustible walls beginning behind it.

Fig. 11-2 Clearance 'A' Diagram

Fig. 11-3 Clearance 'B' Diagram

Fig. 11-4 Clearance 'C' Diagram

Non-combustible

Min.

14"

Non-combustible

substrate

Non-combustible 4"

Combustible

Min.

18"

(Clearance required for

right, left, and rear)

Fig. 11-5 Backsplash clearance

Non-combustible

Backsplash

Min.

Com-

bustible

(Clearance required for

right, left, and rear)

(Clearance required for

right, left, and rear)

Fig. 11-1 Overhead requirements

Min.

Combustible construction:

Requires vent hood or protection kit

Non-combustible construction:

Okay as-is

REV 5 - 1412081445

L-C2-329

Fig. 12-1 - Ventilation diagram

Left-side

hanger

Fig. 12-4

Flex connector

Left-side

support wall

Orient grill

so prevailing

wind blows

this way.

Fig. 12-3

CORRECT

PLACE GRILL SO PREVAILING

WIND BLOWS TOWARD FRONT

OF GRILL

INSTALLATION REQUIREMENTS (Cont.)

The control panel MUST remain removable for servicing

(see PARTS LIST).

ENSURE PROPER COMBUSTION AIR AND

COOLING AIRFLOW

Proper airﬂ ow (Fig. 12-1) MUST be maintained for the

grill to perform as it was designed. If airﬂ ow is blocked,

overheating and poor combustion will result. Do not

block the 1" (2.5 cm) front air inlet along the bottom

of the control panel or

more than 75% of the

cooking grid surface

with pans or griddles.

Note: The 1" (2.5 cm)

front air space

also allows

access to the

drip tray.

EXHAUST REMOVAL

If the grill is installed under an overhead structure that is

constructed of non-combustible material: an exhaust hood

is recommended. See below.

If the grill is installed under an overhead structure that is

constructed of combustible material: an exhaust hood is

required. See below.

Note: An alternative to an exhaust removing vent

hood is an RHP combustible overhead

protection kit. See previous page.

When using an exhaust hood:

The cooking grid area must be covered by an exhaust

hood (with a vent) larger than the cooking surface. Refer

to manufacturer speciﬁ cations. An exhaust fan with a

rating of 1,000 CFM (cubic feet per minute) (472 liters

per second) or more may be necessary to effectively

remove smoke and other cooking by-products from the

area under the hood. RHP Vent Hoods are available,

contact your local dealer.

THIS UNIT MUST NOT BE LOCATED IN A FULLY

ENCLOSED AREA OF ANY KIND.

GAS-SUPPLY PLUMBING REQUIREMENTS

For natural gas or a household propane system, rigid

(1.3 cm) or

" (1.9 cm) black steel pipe or local code-

approved pipe is required to conduct the gas supply to

the unit. Contact your local gas supplier. Connect this

pipe to the required C.S.A.-approved stainless-steel ﬂ ex

connector (attached). An NPT adapter has been provided

for

" pipe. DO NOT use a rubber hose within the grill

enclosure. Apply only joint compounds that are resistant

to all gasses to all male pipe ﬁ ttings except ﬂ are ﬁ ttings.

Make sure to tighten every joint securely.

Note: If

" (1.3 cm) pipe is used with natural gas,

it should be no longer than 20' (6.1 meters).

Important: An external valve (with a removable

key) in the gas line is necessary for

safety when the grill is not in use. It also

provides for convenient maintenance.

CAUTION: Wind blowing into or across the rear

oven lid vent (Fig. 12-2) can cause

poor performance and/or dangerous

overheating. Orient the grill so that the

prevailing wind blows toward the front of

the grill (Fig. 12-3).

GAS SUPPLY AND MANIFOLD PRESSURES:

For natural gas - normal 7" (17.78 cm) water column

(w.c.), minimum 5" (12.7 cm), maximum 10

" (26.7

cm). For propane gas - normal 11" w.c., minimum 10"

(25.4 cm), maximum 13" (33 cm).

YOU MUST PROTECT

REAR OVEN VENT FROM

PREVAILING WIND

Rear oven lid vent

INCORRECT

Fig. 12-2

REV 5 - 1412081445

L-C2-329

FOR YOUR SAFETY, you must provide the openings listed

below for drainage, replacement air, and cross-ventilation

of any storage area exposed to possible leakage from gas

connections, the unit, or propane cylinders.

One side of the enclosure can be left completely open to

the outside, OR 4 ventilation openings must be created:

NATURAL GAS INSTALLS

Two of the openings are to be at the top level (approx.

4" below the countertop) and on opposite walls of the

enclosure. 2 more openings must be at the ﬂ oor level (no

more than 5" above the ﬂ oor) and on opposite sides of the

enclosure. Each opening must have a minimum of 10 sq.

in. of free area. To achieve the proper ventilation, you may

drill a series of holes, omit the grout from masonry joints,

or replace a brick with a hardware cloth screen. If the ﬂ oor

in the cabinet is raised and the space beneath the cabinet

is open to the outside, the lower ventilation openings may

be in the ﬂ oor. Reference Fig. 13-1.

PROPANE GAS INSTALLS

(HOUSEHOLD & CYLINDER)

Two of the openings are to be at the cylinder valve level

(approx. 16" above the ﬂ oor) and on opposite walls of the

enclosure. 2 more openings must be at the ﬂ oor level (no

more than 5" above the ﬂ oor) and on opposite sides of the

enclosure. Each opening must have a minimum of 10 sq.

in. of free area. To achieve the proper ventilation, you may

drill a series of holes, omit the grout from masonry joints,

or replace a brick with a hardware cloth screen. If the ﬂ oor

in the cabinet is raised and the space beneath the cabinet

is open to the outside, the lower ventilation openings may

be in the ﬂ oor. Reference Fig. 13-1.

WHEN A PROPANE CYLINDER IS USED

When a propane cylinder is installed inside of the enclosure,

the guidelines below MUST be followed. FAILURE TO

DO SO MAY CAUSE DAMAGE TO YOUR UNIT AND/OR

PERSONAL INJURY. Reference Fig. 13-2 for an example.

• Only a C.S.A. listed stainless steel connector can be

connected to the grill.

• The regulator/hose assembly coming from the propane

cylinder can only be connected to the above mentioned

grill ﬂ ex connector. DO NOT connect the regulator/

hose assembly directly to the grill. An adapter will

be required.

• A heatshield must be installed to protect the regulator/

hose assembly and propane cylinder valve.

• RHP offers a propane cylinder door with tank tray

to meet the cylinder install requirements. See Fig.

13-3.

Fig. 13-2 Propane cylinder orientation

Fig. 13-1 Ventilation detail

Nat. gas

installs

(repeat for

opposite

side)

Fig. 13-3 Optional RHP door w/tank tray

Adapter

L.P. gas

installs

(repeat for

opposite

side)

Grill

C.S.A. listed

stainless steel

ﬂ ex connector

Heatshield

Regulator/

hose

assembly

L.P.

cylinder

Cylinder & regulator/

hose assembly

protected by heatshield

Equipped with

adapter for hose

assembly and

ﬂ ex connector

ENCLOSURE REQUIREMENTS

REV 5 - 1412081445

L-C2-329

Fig. 14-3

Adjustable

support

screw

Bottom of

face

Bottom

of cut-out

opening

Note: When a propane cylinder is installed inside

of the enclosure, the guidelines found in the

ENCLOSURE REQUIREMENTS section

MUST be followed.

For household propane or natural gas units:

CAUTION: Use only C.S.A. listed stainless-steel ﬂ ex

connectors within the enclosure.

WARNING

A rubber or plastic connector will rupture or leak,

resulting in an explosion or serious injury if used

inside the appliance enclosure.

1. Run the attached ﬂ ex connector routed under the

left side of the grill out of the enclosure and to the

gas stub.

2. Turn OFF the gas supply at the source. Remove

the

/2" adapter that is loosely connected to the ﬂ ex

connector. Attach the adapter to the gas-supply stub

using a pipe joint compound that is resistant to all

gasses. Tighten securely. Then attach the open end

of the ﬂ ex connector to the adapter. Tighten securely.

3. Turn all burner control knobs to the OFF position.

Turn the gas supply on. Then carefully check all gas

connections for leaks with a brush and half-soap/

half-water solution before lighting. NEVER USE A

MATCH OR OPEN FLAME TO TEST FOR LEAKS.

4. Close the dedicated gas-supply shut-off valve, then

slide the grill into place. Do not to pinch, kink, or

damage the gas connector line.

5. Rotate the adjustable support screws to the left to

raise and to the right to lower the respective side

of the appliance grill. Use a

" open-end wrench

as needed.

Important: Do not extend the support screws so

far that any part of the hanger is raised

off the counter top.

COUNTER PREPARATION

Consult Table 1 for non-combustible enclosure cut-out

dimensions. An RHP insulating liner must be used if

any supporting construction is combustible. Consult the

instructions that come with the liner for dimensions and

additional installation information before beginning the

installation.

This outdoor built-in grill must be supported by the

stainless-steel hanger extending from the upper portion

of the grill. The hanger rests on the left, right, and back

of the countertop and on the two front structural supports

with attached adjustable screws located below the control

panel on the left and right sides (see Fig. 14-3).

The control panel is designed to sit ﬂ ush against the

enclosure front wall (see Fig. 14-2). If the non-combustible

enclosure countertop extends beyond the front wall,

creating a countertop overhang (see Fig. 14-1), it must

be cut ﬂ ush with the front wall for the width of the control

panel or a gap will be created exposing the forward

portions of the left and right side grill ﬁ re walls. Reference

the MODEL SPECIFICATIONS section.

Note: It is not necessary to remove the control panel

or knobs to install this unit.

CONNECT THE GAS SUPPLY

For propane cylinders:

For connecting a propane unit to a portable propane tank,

read the safety warnings and follow the instructions in the

section SAFE USE AND MAINTENANCE OF PROPANE

GAS CYLINDERS.

INSTALLATION

Fig. 14-4

OFF

Dedicated manual shut-off valve

To gas

system

(Cut-out)

Pipe

adapter

fitting

(Countertop)

Gas inlet pipe

Flex

connector

Hanger

REV 5 - 1412081445

L-C2-329

Fig. 14-1

Fig. 14-2

GAP CREATED

IDEAL

Flush-mounted

control panel

Proposed cut-

out in overhang

Countertop

Overhang

control panel

stops here

Fig. 15-1

Zone divider

Groove

Front

INSTALLATION (cont.)

INSTALL THE FLAVOR GRIDS

Place the ﬂ avor grids directly onto the studs on the

burners. The panels allow heat from the burners to

be evenly distributed throughout the cooking area.

The panels are stainless steel and will heat and cool

quickly, making your barbecue very responsive to

the changes you specify in grill temperature. They

are rust resistant and may be cleaned with standard

oven cleaners. Some discoloring will be seen with

use. This is normal for stainless steel and does not

affect the function.

Fig. 15-2 Install ﬂ avor grids

Place onto studs

Fig. 15-1 Install zone dividers

REV 5 - 1412081445

L-C2-329

INSTALL ZONE DIVIDERS

Place the zone dividers as shown (Fig. 15-1) into the

grooves in the inner ﬁ rewall of the grill to allow for

maximum heat control and thermometer accuracy in

each zone. Remove and store during rotisserie use.

POWER SUPPLY HOOKUP

CAUTION: IMPROPERLY CONNECTED WIRES

WILL CAUSE DAMAGE TO THE GRILL

AND MAY RESULT IN PROPERTY

DAMAGE AND/OR PERSONAL INJURY.

This grill includes a power supply box. When installing

the power supply box:

• It MUST be located at least 12 inches below the

bottom of the grill (see Fig. 16-3).

• The wire extension that exits from the control panel

MUST be routed directly downward. This will prevent

overheating. DO NOT route the wire extension

below the grill (see Fig. 16-3).

Note: For enclosures with a solid area beneath the

grill, a cutout must me made near the wire

extension to allow for the above requirement.

If an insulating liner is installed, route the wire

down through the nearest hole possible.

• DO NOT block the vent holes found on the box.

Fasten the power supply box to the inside of the

enclosure using appropriate hardware for your enclosure.

The electrical connections from the power supply box to

the grill electrical systems come pre-connected.

WARNING

Electrical Grounding Instructions

This outdoor-cooking gas appliance is equipped with a

three-pronged (grounding) plug. Do not cut or remove

the grounding prong from the plug.

CONNECT THE POWER SUPPLY TO LINE

POWER

Plug the power supply cord into a properly wired

and inspected GFCI electrical receptacle (15 AMP

minimum). Use a heavy-duty grounded extension cord

if necessary.

ELECTRICAL SAFETY

To protect against electric shock, do not immerse cord or plugs in water or other liquid;

Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts;

Do not operate any outdoor cooking gas appliance with a damaged cord, plug, or after the appliance malfunctions

or has been damaged in any manner. Contact the manufacturer for repair;

Do not let the cord hang over the edge of a table or touch hot surfaces;

Do not use an outdoor cooking gas appliance for purposes other than intended;

When connecting, ﬁ rst connect plug to the outdoor cooking gas appliance then plug appliance into the outlet;

Use only a Ground Fault Circuit Interrupter (GFCI) protected receptacle with this outdoor cooking gas appliance;

Never remove the grounding plug or use with an adapter of 2 prongs.

Use only extension cords with a 3 prong grounding plug, rated for the power of the equipment, and approved

for outdoor use with a W-A marking.

Grounded

plug

Required

GFCI electrical

receptacle (not

included)

Fig. 16-3 Power supply clearance

Fig. 16-2 Wire connections

Fig. 16-1 Power supply detail

12"

Min.

Route wires

directly downward

(to prevent

overheating)

ELECTRICAL INSTALLATION

Fig. 17-1 Type I Acme thread quick coupler

Pressure

relief

valve

QCC

Type 1

valve

Brass Acme

thread ﬁ tting

Liquid level

indicator

(optional)

Hand nut with Acme

thread

Regulator

Vent

Hose

Hand wheel

The use of pliers or a wrench should not be necessary. Only

cylinders marked “propane” may be used.

To disconnect: Turn the hand nut counterclockwise until

detached (Fig. 17-1).

Important: Before using the unit, and after each time the

cylinder is removed and reattached, check

the hose for wear (see a.) and check all

connections for leaks. Turn off the unit valves

and open the main cylinder valve, then check

connections with soapy water. Repair any

leaks before lighting the unit.

CAUTION: Always turn the propane cylinder main valve

off after each use, and before moving the unit

and cylinder or disconnecting the coupling.

This valve must remain closed and the

cylinder disconnected while the appliance

is not in use, even though the gas ﬂ ow is

stopped by a safety feature when the coupler

is disconnected.

Carefully inspect the hose assembly each time before the

gas is turned on. A cracked or frayed hose must be replaced

immediately.

If the appliance is stored indoors, the cylinder must be

disconnected and removed. Disconnected

cylinders must be

stored outdoors, out of the reach of children, with threaded

valve plugs tightly installed, and must not be stored in a

building, garage, or any other enclosed area.

FOR YOUR SAFETY

a. DO NOT store a spare propane-gas cylinder under or

near this appliance.

b. NEVER ﬁ ll the cylinder beyond 80-percent full.

c. IF THE INFORMATION IN a. AND b. IS NOT FOLLOWED

EXACTLY, A FIRE CAUSING DEATH OR SERIOUS

INJURY MAY OCCUR.

IMPORTANT FOR YOUR SAFETY

READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.

When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.

FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

CYLINDER/CONNECTOR REQUIREMENTS

a. Propane-gas cylinders, valves, and hoses must be

maintained in good condition and must be replaced if

there is visible damage to either the cylinder or valve. If the

hose is cut or shows excessive abrasion or wear, it must

be replaced before using the gas appliance (see e.).

b. This unit, when used with a cylinder, should be connected

to a standard 5-gallon (20 lb.) propane-gas cylinder

equipped with an OPD (Overﬁ ll Prevention Device).

The OPD has been required on all cylinders sold since

October 1,1998, to prevent overﬁ lling.

c. Cylinder dimensions should be approximately 12" (30.5

cm) in diameter and 18" (45.7 cm) high. Cylinders must

be constructed and marked in accordance with the

Speciﬁ cations for Propane Gas Cylinders of the U.S.

Department of Transportation (D.O.T.) or the National

Standard of Canada, CAN/CSA-B339, Cylinders,

Spheres, and Tubes for Transportation of Dangerous

Goods.

d. The cylinder used must include a collar to protect the

cylinder valve, and the cylinder supply system must be

arranged for vapor withdrawal.

e. The pressure regulator and hose assembly (Fig. 17-1)

supplied with this outdoor gas appliance (L.P. models

only) must be used. Original and replacement pressure

regulator and hose assemblies must be those speciﬁ ed

by the manufacturer for connection with a cylinder

connecting device identiﬁ ed as Type I by the ANSI Z

21.58-2005/CGA 1.6-2005 (see PARTS LIST for ordering

information).

f. The propane-gas cylinder valve must be equipped with a

cylinder connection coupling device, described as Type I

in the standard deﬁ ned in paragraph e. above. This device

is commonly described as an Acme thread quick coupler.

g. If the propane-gas cylinder comes with a dust plug, place

the dust cap on the cylinder valve outlet whenever the

cylinder is not in use.

QUICK COUPLER OPERATION

To connect the regulator/hose assembly to the propane-

gas cylinder valve ﬁ tting: Press the hand nut on the regulator

over the Acme thread ﬁ tting on the cylinder valve. Turn the hand

nut clockwise to engage the threads and tighten until snug.

e. The pressure regulator and hose assembly used must

match the speciﬁ cation for Type I by ANSI Z 21.58-2005/

CGA 1.6-2005 (see Fig. 17-1).

For propane ventilation requirements, see the ENCLOSURE REQUIREMENTS section.

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

Page is loading ...

IDENTIFICATION OF GRILL CONTROLS

Fig. 19-1

Left

main burner

control

knob

Right

main burner

control knob

Digital thermometer

Center main burner

control knob

Fig. 19-2

Left

main

burner

control

knob

Right

main burner

control knob

Backburner

control knob

Digital

thermometer

E1060i control locations

E660i and E790i control locations

Center right main

burner

control knob

Center left main

burner

control knob

Smoker drawer

burner control

knob

Smoker drawer

burner control

knob

Right backburner

control knob

Left

backburner

control

knob

Smoker

drawer

Drip

trays

Control

panel

screw(s)

Smoker

drawer

Drip

tray

Master

switch

Power hood

control switch

(if equipped)

Master

switch

Power hood

control switch

(if equipped)

Control

panel

screw(s)

2. Use a Phillips screwdriver to remove the stainless-

steel motor assembly housing screw. Pull the top

of the housing ﬁ rst up and then outward away

from the lid until the top of the shroud clears the

lip of the motor mount beneath, then remove the

housing completely and set it aside (Fig. 20-3).

3. Use the Allen wrench to loosen and remove the

lid motor assembly locking bolt and washer (see

Fig. 20-4).

Important: Keep this bolt and washer for later use

in converting the unit back to automatic

lid operation.

4. Replace the motor assembly housing and

refasten.

CONFIGURING THE LID FOR MOTORIZED

OPENING AND CLOSING

The unit is shipped in this conﬁ guration, but if you have

conﬁ gured it for manual operation and wish to use the

motorized open/close function again, follow this procedure:

1. Follow steps 1-4 except screw in the locking bolt

in step 3.

The Fire Magic

Power Hood is available as a factory

shipped option. Read the following before using the

grill.

Important: Grill must be connected to electrical

power to open and close lid by motor.

OPENING AND CLOSING THE LID

While set up for motorized opening and closing, the

lid may be controlled using the black rocker switch on

the right side of the control panel.

The rocker switch will lock in any one of three positions:

up–commanding the lid to open, down –commanding

the lid to close, and center–allowing the lid to hold its

current position.

CONFIGURING THE LID FOR MANUAL OPENING

AND CLOSING

WARNING

If the grill has been on recently, all Power Hood

components are potentially hot. Wait for grill to

cool before beginning this procedure or wear

heat-resistant gloves.

CAUTION: Do not push or pull on the lid or its handle

while it is configured for automatic

operation. This could result in damage

to the grill.

To conﬁ gure the lid for manual opening and closing,

simply remove the locking bolt using the following

procedure. This procedure requires the use of the

Allen wrench supplied with this option.

1. Open the lid completely, then set the rocker switch

to the center position and disconnect electrical

power to the unit.

Fig. 20-1

Fig. 20-2

DOWN

Fig. 20-3

Gear cover plate

PULL

Motor

assembly

housing

Fig. 20-4

Locking bolt

Hinge bolt

DOWN

Fig. 20-1

Fig. 20-2

OPTIONAL POWER HOOD

SHUTTING OFF THE UNIT

To shut off the unit, depress each valve control knob

and while pressing turn it clockwise to the OFF position.

Always close the valve from the gas supply after each

use of the unit.

ELECTRONIC LIGHTING

Note: Electronic lighting requires an installed 9-volt

battery with a good charge.

1. Open lid(s) or remove cover(s) from burner(s) to be lit.

2. Turn all gas control knob(s) to their OFF position(s).

3. Turn on the gas at its source.

Note: DO NOT

turn on more

than one valve at

a time for either

electronic or

manual lighting.

4. Depress the desired control knob for 5 seconds,

then, while pressing turn it counterclockwise to the

HI LIGHT position. Once the burner lights, release

the knob.

CAUTION: If a burner does not light within ﬁ ve (5)

seconds of turning on the control knob,

depress the knob and turn it to the OFF

position. WAIT FIVE (5) MINUTES

before repeating step 4. If you smell

gas, follow the instructions on the cover

of this manual. If the burners still do not

light after several attempts, refer to the

instructions for manual lighting.

5. Repeat step 4 for each additional burner to be lit.

WHEN USING A PORTABLE PROPANE TANK

Propane tanks are equipped with a safety shutdown

device that may cause low or no gas pressure/ﬂ ame

at the burners if operating and lighting instructions

are not followed exactly (See important note in the

TROUBLESHOOTING section for more details.)

MANUAL LIGHTING

CAUTION: Always wait ﬁ ve (5) minutes for gas to

clear after any unsuccessful lighting

attempt.

1. Follow steps 1 through 3 (left).

2. Insert either a burning long-barrel butane lighter or

a burning long-stem match through the cooking grid

opening to the top of the lighting tube. (Fig. 21-2).

For backburners, hold the flame

against the surface of the backburner.

For sideburners, hold the ﬂ ame against the burner.

3. Hold the match / lighter ﬂ ame at the top of the lighting

tube for 5 seconds, or, next to the sideburner /

backburner. Then depress the appropriate control

knob and while pressing turn it counterclockwise to

the HI LIGHT position. Remove the lighter or match

when the burner lights, and release the control knob.

4. If the burner does not light, immediately depress

the knob and turn the valve to OFF. WAIT FIVE

(5) MINUTES before repeating steps 2 through 4

of the MANUAL LIGHTING instructions.

Read all instructions before lighting, and follow these instructions each time you light the unit.

Fig. 21-2 - Manual lighting

Lighter

Lighting

tube

3. Hold the match / lighter ﬂ ame at the top of the lighting

tube for 5 seconds, or, next to the backburner. Then

depress the appropriate control knob and while

pressing turn it counterclockwise to the HI LIGHT

position. Remove the lighter or match when the

burner lights, and release the control knob.

Important: When lighting the burner under the

ﬂ avor/smoker drawer, ﬁ rst remove

the drawer so that the burner can be

easily seen. Then replace the drawer

after the burner is lit.

Note: This unit must be connected to 120VAC power

for electronic lighting.

Fig. 21-1 - Control knob

OFF

LIGHT

LOW

TURN OFF

TO TURN ON

Read setting

here

HIGH to

LIGHT

Read setting here

(OFF position shown)

To Turn OFF

To Turn ON

Use

HI (high)

to light

Press

knob in

to turn

Gas Flow

Indicator

For your convenience and safety; when the

control knob is in the on position, the gas ﬂ ow

indicator will change from blue to red. (Red

indicates gas ﬂ ow.) See Fig. 21-1.

LIGHTING (IGNITION) INSTRUCTIONS

Page is loading ...

DIGITAL THERMOMETER / INTERIOR AND KNOB LIGHTS

Your grill comes with a digital thermometer for temperature

monitoring and timed cooking. Pressing any button will turn on

the thermometer. The thermometer will automatically shut off

after 5 minutes if no temperature change is detected.

Note: The thermometer also controls the interior lights, and

knob backlights. Thermometer shutdown will not shut

off these lights; they must be manually shut off.

The thermometer is located on the control panel between the

control knobs.

Plug in the meat probe on the right side of the control panel

as shown in Fig. 23-1.

For best performance and temperature readings center the

zone separators properly between each burner (see PARTS

LIST).

Read the following sections completely regarding thermometer

operation. Refer to Fig. 23-2 for thermometer orientation and

button locations.

Prior to initial use; calibrate the thermometer (following

page). Whenever the master switch is turned off or the

power supply is disconnected, allow 30 seconds for the

thermometer to initialize the next time it is powered on.

DEFAULT SCREEN

Press any button to turn the thermometer ON. The default

screen will be displayed. All temperatures for the cooking zones

(see Grilling Tips section) and the meat probe will be shown (Fig.

23-3). See below for options under the default screen.

Setting a Location Temperature

1. Press the up/down arrow to switch to the desired location

(a cooking zone or the meat probe). Press SET.

2. The selected location’s temperature screen will be

displayed. Use the arrows to set the desired temp. The

actual temp. will also be shown. (See Fig. 23-4.)

Note: PRESSING the arrows will adjust the desired temp.

by increments of one degree. HOLDING them down

(for several seconds) will adjust the temp. rapidly.

3. Press SET to return to the default screen. Repeat as

necessary for all other locations.

The alarm will sound (if set to do so) when a location reaches its

set temperature. The alarm is silenced by pressing any button

on the thermometer.

Interior and Knob Lights

1. Press the light button to turn both the interior lights and knob

backlights ON. The interior lights will temporarily shut off when

the hood is closed (except for Magic View models).

2. Press the light button once to turn the interior lights OFF,

and a second time to turn the knob backlights OFF.

Note: Thermometer shutdown will not shut off these

lights; they must be manually shut off by turning the

thermometer back ON and pressing the light button.

SET

Fig. 23-2 Orientation

Arrows for adjusting digits

SET button

for selecting

& conﬁ rming

Display screen

Timer button

Light button

button

080

SET

05:00

350

075078

350

078

350

170

PROBE

TEMP

ZONE 3ZONE 2ZONE 1

SET ACT

°F

ACT

SET

Fig. 23-3 Default screen detail

Time set via TimerMeat probe temp. info

Cooking zones temp. info

SET

ZONE 1

ACTUAL: 078

SET TEMP: 350

Fig. 23-4 Location temp. screen (zone 1 shown)

Current location

Set this temp. as desired

Use arrows to set

Fig. 23-1 Meat probe detail

MEAT

PROBE

Meat probe handle

Meat probe plug

Page is loading ...

Fire Magic Echelon Diamond Built-In Grill User manual

Brand: Fire Magic

Model: Echelon Diamond Built-In Grill

Category: Barbecues & grills

Type: User manual

Download PDF

report

Fire Magic Echelon Diamond Built-In Grill User manual

Fire Magic Echelon Diamond Built-In Grill User manual

Related papers

Other documents