Dodge Challenger User manual

2009 CHALLENGER SRT8

CHALLENGER SRT8

Chrysler LLC

81-226-0914

Second Edition Printed in U.S.A.

OWNER’S MANUAL

2009

VEHICLES SOLD IN CANADA

With respect to any Vehicles Sold in Canada, the name

Chrysler LLC shall be deemed to be deleted and the

name Chrysler Canada Inc. used in substitution there-

fore.

DRIVING AND ALCOHOL

Drunken driving is one of the most frequent causes of

accidents.

Your driving ability can be seriously impaired with blood

alcohol levels far below the legal minimum. If you are

drinking, don’t drive. Ride with a designated non-drinking

driver, call a cab, a friend, or use public transportation.

WARNING!

Driving after drinking can lead to an accident. Your

perceptions are less sharp, your reflexes are slower,

and your judgment is impaired when you have been

drinking. Never drink and then drive.

This manual illustrates and describes the operation of

features and equipment that are either standard or op-

tional on this vehicle. This manual may also include a

description of features and equipment that are no longer

available or were not ordered on this vehicle. Please

disregard any features and equipment described in this

manual that are not on this vehicle.

Chrysler LLC reserves the right to make changes in

design and specifications, and/or make additions to or

improvements to its products without imposing any

obligation upon itself to install them on products previ-

ously manufactured.

TABLE OF CONTENTS

SECTION PAGE

1

INTRODUCTION

.............................................................3

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

...............................9

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

...............................71

4

UNDERSTANDING YOUR INSTRUMENT PANEL

................................... 149

5

STARTING AND OPERATING

................................................. 239

6

WHAT TO DO IN EMERGENCIES

...............................................319

7

MAINTAINING YOUR VEHICLE

............................................... 335

8

MAINTENANCE SCHEDULES

..................................................385

9

IF YOU NEED CONSUMER ASSISTANCE

..........................................403

10

INDEX

....................................................................415

1

2

3

4

5

6

7

8

9

10

INTRODUCTION

CONTENTS

䡵 Introduction .......................... 4

䡵 How To Use This Manual ................. 4

䡵 Warnings And Cautions .................. 6

䡵 Vehicle Identification Number ............. 6

䡵 Vehicle Modifications/Alterations ........... 7

1

INTRODUCTION

This Owner’s Manual has been prepared with the assis-

tance of service and engineering specialists to acquaint

you with the operation and maintenance of your vehicle.

It is supplemented by a Warranty Information Booklet

and various customer-oriented documents. You are

urged to read these publications carefully. Following the

instructions and recommendations in this manual will

help assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored

in the vehicle for convenient referencing and remain

with the vehicle when sold, so that the new owner will

be aware of all safety warnings.

When it comes to service, remember that your authorized

dealer knows your vehicle best, has the factory-trained

technicians and genuine MOPAR威 parts, and is inter-

ested in your satisfaction.

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section

contains the information you desire.

The detailed index at the back of this Owner’s Manual

contains a complete listing of all subjects.

Consult the following table for a description of the

symbols that may be used on your vehicle or throughout

this Owner’s Manual:

4 INTRODUCTION

INTRODUCTION 5

1

WARNINGS AND CAUTIONS

This Owner’s Manual contains WARNINGS against op-

erating procedures that could result in an accident or

bodily injury. It also contains CAUTIONS against proce-

dures that could result in damage to your vehicle. If you

do not read this entire manual, you may miss important

information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is on the left

front corner of the instrument panel and is visible from

outside of the vehicle through the windshield. This

number also appears on the Automobile Information

Disclosure Label affixed to a window on your vehicle, the

vehicle registration, and the title.

6 INTRODUCTION

NOTE: It is illegal to remove the VIN.

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could

seriously affect its roadworthiness and safety and

may lead to an accident resulting in serious injury or

death.

VIN Location

INTRODUCTION 7

1

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

䡵 A Word About Your Keys ................ 12

▫ Wireless Ignition Node (WIN) ........... 12

▫ FOB With Integrated Key .............. 13

▫ Ignition Key Removal ................. 13

▫ Key-In-Ignition Reminder .............. 14

䡵 Sentry Key威 ......................... 14

▫ Replacement Keys ................... 16

▫ Customer Key Programming ............ 16

▫ General Information .................. 17

䡵 Vehicle Security Alarm .................. 18

▫ Rearming Of The System .............. 18

▫ To Arm The System .................. 18

▫ To Disarm The System ................ 18

䡵 Illuminated Entry System ................ 19

䡵 Remote Keyless Entry (RKE) ............. 20

▫ To Unlock The Doors ................. 20

▫ To Lock The Doors ................... 22

▫ Express Down Window Feature .......... 23

2

▫ To Open The Trunk .................. 23

▫ Using The Panic Alarm ................ 24

▫ Programming Additional Transmitters ..... 24

▫ Transmitter Battery Service ............. 24

▫ General Information .................. 25

䡵 Remote Starting System ................. 26

▫ How To Use Remote Start .............. 26

䡵 Door Locks .......................... 28

▫ Manual Door Locks .................. 28

▫ Power Door Locks ................... 29

䡵 Windows ........................... 31

▫ Power Windows ..................... 31

▫ Wind Buffeting ...................... 33

䡵 Trunk Lock And Release ................ 33

䡵 Trunk Safety Warning .................. 34

▫ Trunk Emergency Release .............. 34

䡵 Occupant Restraints .................... 35

▫ Lap/Shoulder Belts .................. 36

▫ Lap/Shoulder Belt Untwisting Procedure . . . 41

▫ Seat Belt Pretensioners ................ 41

▫ Enhanced Seat Belt Use Reminder System

(BeltAlert威) ......................... 41

▫ Automatic Locking Mode — If Equipped . . . 43

▫ Seat Belts And Pregnant Women ......... 43

▫ Seat Belt Extender ................... 44

▫ Driver And Front Passenger Supplemental

Restraint System (SRS) - Airbags .......... 44

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

▫ Event Data Recorder (EDR) ............. 54

▫ Child Restraint ...................... 56

䡵 Engine Break-In Recommendations ......... 65

䡵 Safety Tips .......................... 66

▫ Transporting Passengers ............... 66

▫ Exhaust Gas ........................ 67

▫ Safety Checks You Should Make Inside The

Vehicle ............................. 68

▫ Periodic Safety Checks You Should Make

Outside The Vehicle ................... 69

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11

2

A WORD ABOUT YOUR KEYS

Your vehicle uses a keyless ignition system. This system

consists of a Fob with Integrated Key and a Wireless

Ignition Node (WIN) with an integral ignition switch.

You can insert the double-sided integrated key into the

ignition switch with either side up.

Keyless Go Feature

This vehicle may be equipped with the Keyless Go

feature, for more information, refer to “Keyless Go — If

Equipped” under “Starting Procedure” in Section 5 of

this manual.

Wireless Ignition Node (WIN)

The Wireless Ignition Node (WIN) operates similar to an

ignition switch. It has four operating positions, three with

detents and one that is spring-loaded. The detent posi-

tions are LOCK, ACC, and ON. The START position is a

spring-loaded momentary contact position. When re-

leased from the START position, the switch automatically

returns to the ON position.

1 — LOCK

2 — ACCESSORY

3—ON

4 — START

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Fob With Integrated Key

The Fob with Integrated Key operates the ignition switch.

It also contains the Remote Keyless Entry (RKE) trans-

mitter and a valet key, which stores in the rear of the Fob.

The valet key allows for entry into the vehicle should the

battery in the vehicle or the Fob go dead. The valet key is

also for locking the glove box. You can keep the valet key

with you when valet parking.

To remove the valet key from the Fob, slide the mechani-

cal latch at the top of the Fob sideways with your thumb

and then pull the key out of the Fob with your other

hand.

NOTE: You can insert the double-sided valet key into

the lock cylinders with either side up.

Ignition Key Removal

Place the shift lever in PARK. Turn the key to the LOCK

position and then remove the key.

Valet Key Removal

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

2

NOTE: The power window switches, radio, power

sunroof (if equipped), and ignition-powered power out-

lets will remain active for up to 60 minutes after the

ignition switch is turned to the LOCK position. Opening

either door will cancel this feature. The time for this

feature is programmable. Refer to “Delay Power Off to

Accessories Until Exit,” under “Personal Settings (Cus-

tomer Programmable Features),” under “Electronic Ve-

hicle Information Center (EVIC)” in Section 4.

WARNING!

Never leave children alone in a vehicle. Leaving

unattended children in a vehicle is dangerous for a

number of reasons. A child or others could be seri-

ously or fatally injured. Don’t leave the key in the

ignition. A child could operate power windows,

other controls, or move the vehicle.

CAUTION!

An unlocked car is an invitation to thieves. Always

remove key from the ignition and lock all doors

when leaving the vehicle unattended.

Key-In-Ignition Reminder

If you open the driver’s door and the key is in the

ignition, a chime will sound to remind you to remove the

key.

NOTE: The Key-In-Ignition reminder only sounds

when the ignition key is placed in the LOCK or ACC

position.

SENTRY KEY姞

The Sentry Key威 Immobilizer System prevents unautho-

rized vehicle operation by disabling the engine. The

system does not need to be armed or activated. Operation

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

is automatic, regardless of whether the vehicle is locked

or unlocked.

The system uses the factory-mated Remote Keyless Entry

(RKE) transmitter with integrated key and Wireless Igni-

tion Node (WIN) to prevent unauthorized vehicle opera-

tion. Therefore, only RKE transmitters that are pro-

grammed to the vehicle can be used to start and operate

the vehicle. The system will not allow the engine to crank

if an invalid RKE transmitter is used to operate the

ignition switch.

After turning the ignition switch to the ON position, the

Vehicle Security Light will turn on for three seconds for a

bulb check. If the light remains on after the bulb check, it

indicates that there is a problem with the electronics. This

condition will result in the engine being shut off after two

seconds.

If the Vehicle Security Light turns on during normal

vehicle operation (vehicle running for longer than 10 sec-

onds), it indicates that there is a fault in the electronics.

Should this occur, have the vehicle serviced as soon as

possible.

NOTE:

•

The Sentry Key威 Immobilizer System is not compat-

ible with aftermarket remote starting systems. Use of

these systems may result in vehicle starting problems

and loss of security protection.

•

Exxon/Mobil Speedpass™, additional RKE transmit-

ters, or any other transponder-equipped components

on the same key chain will not cause a fault unless the

additional part is physically held against the trans-

mitter being used to start the vehicle. Cell phones,

pagers, or other RF electronics will not cause interfer-

ence with this system.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

2

All of the RKE transmitters provided with your new

vehicle have been programmed to the vehicle electronics.

Replacement Keys

NOTE: Only RKE transmitters that are programmed to

the vehicle electronics can be used to start and operate

the vehicle. Once a transmitter is programmed to a

vehicle, it cannot be programmed to any other vehicle.

CAUTION!

Always remove the keys from the vehicle and lock all

doors when leaving the vehicle unattended.

At the time of purchase, the original owner is provided

with a four-digit Personal Identification Number (PIN).

Keep the PIN in a secure location. This number is

required for authorized dealer replacement of RKE trans-

mitters. Duplication of RKE transmitters may be per-

formed at an authorized dealer or by using the Customer

Key Programming procedure. This procedure consists of

programming a blank transmitter to the vehicle electron-

ics. A blank transmitter is one that has never been

programmed.

NOTE: When having the Sentry Key威 Immobilizer

System serviced, bring all vehicle RKE transmitters with

you to the authorized dealer.

Customer Key Programming

If you have two valid RKE transmitters with integrated

keys, you can program new transmitters to the system by

performing the following steps:

1. Insert the first valid integrated key into the ignition

switch and turn the ignition switch to the ON position for

at least three seconds, but no longer than 15 seconds.

Turn the ignition switch to the LOCK position and

remove the first key.

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. Insert the second valid integrated key and turn the

ignition switch to the ON position within 15 seconds.

After 10 seconds, a chime will sound and the Vehicle

Security Light will begin to flash. Turn the ignition switch

to the LOCK position and remove the second key.

3. Insert a blank integrated key into the ignition switch

and turn the ignition switch to the ON position within

60 seconds. After 10 seconds, a single chime will sound

and the Vehicle Security Light will stop flashing, turn on

again for three seconds, and then turn off.

The new integrated key is programmed. The RKE trans-

mitter will also be programmed during this procedure.

Repeat this procedure to program up to eight keys. If you

do not have a programmed RKE transmitter with inte-

grated key, contact your authorized dealer for details.

NOTE: If a programmed key is lost, see your authorized

dealer to have all remaining keys erased from the sys-

tem’s memory. This will prevent the lost key from

starting your vehicle. The remaining keys must then be

reprogrammed. All vehicle keys must be taken to an

authorized dealer at the time of service to be

reprogrammed.

General Information

The Sentry Key威 system complies with FCC rules Part 15

and with RSS-210 of Industry Canada. Operation is

subject to the following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference that may be

received, including interference that may cause undes-

ired operation.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

2

VEHICLE SECURITY ALARM

The Vehicle Security Alarm monitors the vehicle doors

for unauthorized entry and the ignition switch for unau-

thorized operation. If something triggers the alarm, the

Vehicle Security Alarm will prevent the vehicle from

starting and provide the following audible and visible

signals: the horn will pulse, the headlights will flash, the

park lights will flash, and the Vehicle Security Light in

the instrument cluster will flash.

Rearming Of The System

If something triggers the alarm, and no action is taken to

disarm it, the Vehicle Security Alarm will turn the horn

off after three minutes, turn all of the visual signals off

after 15 minutes, and then the Vehicle Security Alarm will

rearm itself.

To Arm The System

Remove the key from the ignition switch and either press

a power door LOCK switch while the driver or passenger

door is open or press the LOCK button on the Remote

Keyless Entry (RKE) transmitter. After the last door is

closed, or if both doors are closed, the Vehicle Security

Alarm will arm itself in about 16 seconds. During that

time, the Vehicle Security Light will flash. If it does not

illuminate, the Vehicle Security Alarm is not arming. In

addition, if you open a door during the arming period,

the Vehicle Security Alarm will cancel the arming pro-

cess. If you wish to rearm the Vehicle Security Alarm after

closing the door, you must repeat one of the previously-

described arming sequences.

To Disarm The System

Either press the UNLOCK button on the RKE transmitter

or insert a valid ignition key into the ignition switch and

turn the key to the ON position.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Page is loading ...

Dodge Challenger, 2009 Challenger SRT, 2009 Challenger SRT8, Challenger SRT User manual

Related papers

Other documents