ACE 7275340 Owner's manual

Category
Grass trimmers
Type
Owner's manual

This manual is also suitable for

Operator's Manual
M
2-Cycle
WEEDWACKER® GAS TRIMMER
Model No. 316.791081
UNgtLtEFAIILE S TARTtN_ £ A S E _
o SAFETY
ASSEMBLY
OPERATION
MAINTENANCE
PARTS LIST
ESPANOL, R 13
CAUTION: Before using this
product, read this manual
and follow all safety rules
and operating instructions.
Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.
Visit our website: www.craftsrnan.corn
769-06126 P00 06/10
CALiFORNiA PROPOSiTiON 65 WARNING
THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALS
KNOWN TO THE STATE OF CALiFORNiA TO CAUSE CANCER, BIRTH
DEFECTS OR OTHER REPRODUCTIVE HARM.
TABLE OF CONTENTS
Safety Rules ................................................. 2
Warranty .................................................... 3
Know Your Unit ............................................... 4
Assembly Instructions .......................................... 4
Oil and Fuel Information ........................................ 5
Starting/Stopping Instructions ................................... 6
Operating Instructions ......................................... 6
Maintenance and Repair Instructions .............................. 7
Cleaning and Storage .......................................... 9
Troubleshooting Chart ........................................ 10
Specifications ............................................... 11
Parts List ................................................... 30
Service Numbers ..................................... Back Cover
SPARK ARRESTOR NOTE
NOTE: For users on U.S. Forest Land and in the states of California, Maine,
Oregon and Washington. All U.S. Forest Land and the state of California
(Public Resources Codes 4442 and 4443), Oregon and Washington require, by
law that certain internal combustion engines operated on forest brush and/or
grass-covered areas be equipped with a spark arrestor, maintained in effective
working order, or the engine be constructed, equipped and maintained for the
prevention of fire. Check with your state or local authorities for regulations
pertaining to these requirements. Failure to follow these requirements could
subject you to liability or a fine. This unit is factory equipped with a spark
arrestor. If it requires replacement, ask your LOCAL SERVICE DEALER to install
the Accessory Part #753-06182 Muffler Assembly
The purpose of safety symbols is to attract your attention to possible I
dangers. The safety symbols, and their explanations, deserve your careful
attention and understanding. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not_
substitutes for proper accident prevention measures. J
SYMBOL MEANING
,_ SAFETY ALERT: Indicates danger, warning or caution.
Attention is required in order to avoid serious personal injury. May
be used in conjunction with other symbols or pictographs.
NOTE: Advises of information or instructions vital to the operation or
maintenance of the equipment.
DANGER: Failure to obey a safety warning will result in serious
injury to yourself or to others. Always follow the safety precautions
i _ to reduce the risk of fire, electric shock and personal injury.
i
i
WARNING: Failure to obey a safety warning can result in injury
to yourself and others. Always follow the safety precautions to
reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in
i _ property damage or personal injury to yourself or to others.
i
Always follow the safety precautions to reduce the risk of fire,
i
i electric shock and personal injury.
i
NOTE-
This Unit Can Use a Plug=in Power Start or Power Bit Start
Optional Accessory!
Please refer to the Plug-In Power Start or Power Bit Start
operator's manual for proper use of these features. (Items Sold
Separately! Please refer to page 9 of this manual for more
information about purchasing these accessories.)
Read the Operator's Manual and follow all warnings and safety
instructions. Failure to do so can result in serious injury to the operator
and/or bystanders. FOR QUESTIONS, CALL 1-800-4-MY-HOME®
All information, illustrations, and specifications in this manual are based on the
latest product information available at the time of printing. We reserve the right
to make changes at any time without notice.
READ ALL INSTRUCTIONS BEFORE OPERATING
= IMPORTANT SAFETY INSTRUCTIONS
I_, IWARNING: When using the unit, all safety rules must be
I
followed. Please read these instructions before operating the unit
in order to ensure the safety of the operator and any bystanders.
Please keep these instructions for later use.
Read the instructions carefully. Be familiar with the controls and proper
use of the unit.
Do not operate this unit when tired, ill, or under the influence of alcohol,
drugs, or medication.
Children and teens under the age of 15 must not use the unit, except for
teens guided by an adult.
All guards and safety attachments must be installed properly before
operating the unit.
Inspect the unit before use. Replace damaged parts. Check for fuel leaks.
Make sure all fasteners are in place and secure. Replace parts that are
cracked, chipped, or damaged in any way. Do not operate the unit with
loose or damaged parts.
Carefully inspect the area before starting the unit. Remove all debris and
hard or sharp objects such as glass, wire, etc.
Be aware of the risk of injury to the head, hands and feet.
Clear the area of children, bystanders, and pets. At a minimum, keep all
children, bystanders, and pets outside a 50 feet (15 m) radius; there still may
be a risk to bystanders from thrown objects. Bystanders should be
encouraged to wear eye protection. If approached, stop the unit immediately.
Use only 0.095 inch (2.41 mm) diameter original equipment manufacturer
replacement line. Never use metal-reinforced line, wire or rope. These can
break off and become dangerous projectiles.
Squeeze the throttle control and check that it returns automatically to the
idle position. Make all adjustments or repairs before using unit.
SAFETY WARNINGS FOR GAS UNITS
1
Gasoline is highly flammable and its vapors can
WARNING:
exp ode f gn ted. Take the fo ow ng precaut ons: |
Store fuel only in containers specifically designed and approved for the
storage of such materials.
Always stop the engine and allow it to cool before filling the fuel tank.
Never remove the fuel tank cap or add fuel when the engine is hot.
Always loosen the fuel tank cap slowly to relieve any pressure in the tank
before fueling. Do not smoke.
Always mix and add fuel in a clean, well-ventilated outdoor area where
there are no sparks or flames. Do not smoke.
Never operate the unit without the fuel cap securely in place.
Avoid creating a source of ignition for spilled fuel. Wipe up any spilled fuel
from the unit immediately before starting the engine. Move the unit at
least 30 feet (9.1 m) from the fueling source and site before starting the
engine. Do not smoke.
Never start or run the unit inside a closed room or building. Breathing exhaust
fumes can kill. Only operate this unit in a well-ventilated outdoor area.
WHILE OPERATING
Never start or run the unit inside a closed room or building. Breathing exhaust
fumes can kill. Operate this unit only in a well ventilated outdoor area.
Wear safety glasses or goggles that are marked as meeting ANSI Z87.1 -
1989 standards. Also wear ear/hearing protection when operating this
unit. Wear a face or dust mask if the operation is dusty. Long sleeve shirts
are recommended.
Wear heavy, long pants, boots and gloves. Do not wear loose clothing,
jewelry, short pants, sandals or go barefoot. Secure hair above shoulder level.
The cutting head shield must always be in place while operating the unit. Do
not operate unit without both trimming lines extended, and the proper line
installed. Do not extend the trimming line beyond the length of the shield.
The cutting attachment may spin during idle speed adjustments. Wear
protective clothing and observe all safety instructions to prevent serious
personal injury.
Adjust the position of the D-handle to provide the best grip.
Be sure the cutting head is not in contact with anything before starting the unit.
+Usetheunitonlyindaylightorgoodartificiallight.
+ Avoid accidental starting. Be in the starting position whenever pulling the
starter rope. The operator and unit must be in a stable position while
starting. See Starting/Stopping Instructions.
Use the right tool. Only use this tool for the purpose intended.
Do not overreach. Always keep proper footing and balance.
Always hold the unit with both hands when operating. Keep a firm grip on
both the front and rear handle or grips.
+ Keep hands, face, and feet at a distance from all moving parts. Do not
touch or try to stop the cutting head when it is rotating.
+ Do not touch the engine or muffler. These parts get extremely hot from
operation. They remain hot for a short time after turning off the unit.
+ Do not operate the engine faster than the speed needed to cut, trim or
edge. Do not run the engine at high speed when not cutting.
This unit has an overspeed protection switch to keep the unit from
overheating. When the unit is run at full throttle while not in use for
extended lengths of time the overspeed protection switch will engage.
Always stop the engine when cutting is delayed or when walking from one
cutting location to another.
If the unit is struck or becomes entangled with a foreign object, stop the
engine immediately and check for damage. Do not operate before
repairing damage. Do not operate the unit with loose or damaged parts.
+ Stop and switch the engine to off for maintenance, repair, or for changing
the cutting head or other attachments.
Use only replacement parts and accessories listed in the Parts List section
of this operator's manual and distributed by a Craftsman outlet or service
center. Use of any replacement parts or accessories purchased elsewhere
may be hazardous and will also void the warranty.
+ Keep unit clean of vegetation and other materials. They may become
lodged between the cutting head and shield.
+ To reduce fire hazard, keep the engine and muffler free from grass, leaves,
excessive grease or carbon build up.
OTHER SAFETY WARNINGS
+ Never store the unit, with fuel in the tank, inside a building where fumes
may reach an open flame or spark.
+ Allow the engine to cool before storing or transporting. Be sure to secure
the unit while transporting.
Store the unit in a dry area, locked up or up high to prevent unauthorized
use or damage, out of the reach of children.
Never douse or squirt the unit with water or any other liquid. Keep handles
dry, clean and free from debris. Clean after each use. See the Cleaning
and Storage instructions.
Keep these instructions. Refer to them often and use them to instruct other
users. If loaning someone this unit, also loan them these instructions.
SAVE THESE INSTRUCTIONS
+ SAFETY & INTERNATIONAL SYMBOLS +
This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for
complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING SYMBOL MEANING
CRAFTSMAN 2 YEAR FULL WARRANTY
FOR 2 YEARS from the date of purchase, this product is warranted against any defects in material or workmanship. Defective product will receive free repair or
free replacement if repair is unavailable.
For warranty coverage details to obtain repair or replacement, visit the web site: www.craftsman.com
This warranty covers ONLY defects in material and workmanship. Warranty coverage does NOT include:
+ Expendable items that can wear out from normal use within the warranty period, such as cutting line, filters or spark plugs.
+ Product damage resulting from user attempts at product modification or repair or caused by product accessories.
,, Repairs necessary because of accident or failure to operate or maintain the product according to all supplied instructions.
,, Preventive maintenance, or repairs necessary due to improper fuel mixture, contaminated or stale fuel.
This warranty is void if this product is ever used while providing commercial services or if rented to another person.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
3
APPLICATIONS
As a trimmer:
Cutting grass and light weeds
Edging
Decorative trimming around trees, fences, etc.
Other optional accessories may be used with this unit.
Shaft Grip
Muffler
Spark Plug
Starter Rope
Grip
On/Oft
Control
D-Handle
Air Filter
Cover
Line Cutting
Blade
\
Shaft Housing
Throttle
Controm
Fuel Cap
Convertible TM
Coupler Primer Bulb
Cutting Head
Cutting Head Shield
INSTALL CUTTING HEAD SHIELD
-- i_L_ ARNING: To prevent serious personal injury, never operate
the trimmer without the cutting head shield in place.
Use the following instructions if the cutting attachment shield on the unit is
not installed. Use only the instructions that apply to the type of shaft and
shield that the unit is equipped with.
1. Place the cutting head shield
onto the shaft housing. Be
sure the guard mounting
bracket slides into the slot on
the edge of the cutting
shield. Rotate the shield into
place, counterclockwise (Fig.
1). The holes in the guard
mounting bracket and cutting
head shield will line up.
2. From inside the cutting head
shield, push the square bolt
through the hole until the
threaded end protrudes
through the guard mounting
bracket (Fig. 2).
3. Put the washer on the bolt,
then screw the wing nut onto
the bolt and tighten.
Cutting Head Shield Mount
Bracket
Fig. I
Washer
Nut
Square Bolt
INSTALLAND ADJUSTTHED-
HANDLE
1. PushtheD-handledown
2.
onto the shaft housing (Fig.
3). The hex bolt hole in the
handle should be on the left
side.
Insert the bolt into the hex
hole in the handle and push
through. Place the washer on
the bolt, then screw the wing
nut onto the bolt. Do not
tighten until making the
handle adjustment.
Shaft Grip Shaft Housing
Tighten
Fig. 3
3. Rotate the D-handle to place the grip above the top of the shaft
housing. Place it a minimum of 6 inches (15.24 cm) from the end of the
shaft grip.
4. While holding the unit in the operating position (Fig. 11), move the D-
handle to the location that provides the best grip.
5. Tighten the wing nut until the D-handle is secure.
Fig. 2
OPERATING THE CONVERTIBLE TM COUPLER SYSTEM
WARNING: Before using any attachment, read and understand I
the manual that came with the attachment. Follow all safety |
information contained within.
J
The Convertible TM coupler system enables the use of these optional attachments.
Edger
Cultivator
Turbo Blower
Brushcutter
Pole Saw
Hedge Trimmer
INSTALLING THE TRIMMER ATTACHMENT OR OTHER ATTACHMENT
m
I _, I WARNING" To avoid serious personal injury and damage to the I
_ unit, shut the unit off before removing or installing attachment.
_ CAUTION: Before operating the unit, be sure that the release 1
button is fully snapped into the primary hole, and that the knob is
securely tightened.
NOTE: To make installing or Primary Hole
removing the attachment
easier, place the unit on _ _, _---_¢--"_"
the ground or on a work
bench.
1. Turn knob counterclockwise _,, .lj____ _
to loosen (Fig. 5).
2. While firmly holding the
attachment, push it straight Upper Shaft Lower Shaft
into the Convertible TM
coupler until the release
button snaps firmly into the
primary hole (Fig. 4).
NOTE: Aligning the release
button with the guide
recess will help
installation (Fig. 6).
3. Turn the knob clockwise to
tighten (Fig. 5).
For decorative edging with the line
head trimmer attachment or other
attachment, lock the release
button of the attachment into the
90° hole (Fig. 5).
Housing
90° Edging Hole
(Trimmer Only}
Fig. 4
Housing
Fig. 5
REMOVING THE TRIMMER ATTACHMENT OR OTHER ATTACHMENT
1. Turn the knob counterclockwise to loosen (Fig. 5).
2. Press and hold the release button (Fig. 6).
3.
While firmly holding the upper
shaft housing, pull the
attachment straight out of the
Convertible TM coupler (Fig. 4). --
Convertible TM Release Button
Coupler
Guide Recess
Fig. 6
OiL AND FUEL MIXING INSTRUCTIONS
Old and/or improperly mixed fuel are the main reasons for the unit not
running properly. Be sure to use fresh, clean unleaded fuel. Follow the
instructions carefully for the proper fuel/oil mixture.
Definition of Blended Fuels
m i_[_ ARN|NG: It has been proven that fuel containing greater than
15% ethanol will likely damage this engine and void the warranty.
Today's fuels are often a blend of gasoline and oxygenates such as ethanol,
methanol, or MTBE (ether). Alcohol-blended fuel absorbs water. As little as 1%
water in the fuel can make fuel and oil separate. It forms acids when stored.
When using alcohol-blended fuel, use fresh fuel (less than 30 days old).
Using Blended Fuels
If choosing to use a blended fuel, or its use is unavoidable, follow
recommended precautions:
Always use the fresh fuel mix explained in the operator's manual
Always agitate the fuel mix before fueling the unit
Drain the tank and run the engine dry before storing the unit
Using Fuel Additives
_ CAUTION: For proper engine operation and maximum
reliability, pay strict attention to the oil and fuel mixing instructions
on the 2-cycle oil container. Using improperly mixed fuel can
severely damage the engine.
The bottle of 2-cycle oil that came with the unit contains a fuel additive that
will help inhibit corrosion and minimize the formation of gum deposits.
Always use a good 2-cycle oil designed for air-cooled engines along with a
fuel additive, such as STA-BIL® Gas Stabilizer or an equivalent. Add 0.8 oz.
(23 ml) of fuel additive per gallon of fuel according to the instructions on the
container. NEVER add fuel additives directly to the unit's fuel tank.
Thoroughly mix the proper ratio of
2-cycle engine oil with unleaded
gasoline in a separate fuel can. Use
a 40:1 fuel/oil ratio. Do not mix
them directly in the engine fuel tank.
See the table below for specific gas
and oil mixing ratios.
NOTE: One gallon (3.8 liters) of
unleaded gasoline mixed
with one 3.2 oz. (95 ml)
bottle of 2-cycle oil makes
a 40:1 fuel/oil ratio.
NOTE: Dispose of the old fuel/oil
mix in accordance to
Federal, State and Local
regulations.
UNLEADED GAS
f GALLON US
(3.8 LITERS}
f LITER
2 CYCLE OIL
3.2 FL OZ.
195ml)
25 ml
MIXING RATIO =40:1
_ WARN|NG: Gasoline is extremely flammable. Ignited vapors
may explode. Always stop the engine and allow it to cool before
filling the fuel tank. Do not smoke while filling the tank. Keep
sparks and open flames at a distance from the area.
FUELING THE UNIT
_ WARN|NG: Remove fuel cap slowly to avoid injury from fuel
spray. Never operate the unit without the fuel cap securely in place.
_ WARNING: Add fuel in a clean, well ventilated outdoor area. Wipe
up any spilled fuel immediately. Avoid creating a source of ignition for
spilt fuel. Do not start the engine until fuel vapors dissipate.
1. Turn unit on its side, with the fuel cap facing up, and remove the fuel cap.
2. Place the gas container's spout into the fill hole on the fuel tank and fill
the tank.
NOTE: Do not overfill the tank.
3. Wipe up any gasoline that may have spilled.
4. Reinstall the fuel cap.
5. Move the unit at least 30 ft. (9.1 m) from the fueling source and site
before starting the engine.
5
m
A I WARNING: Operate this unit only in a well-ventilated outdoor area.
i
_ Carbon monox de exhaust fumes can be etha n a conf ned area. j
_llb I WARNING: Avoid accidental starting. Make sure to be in the !
starting position when pulling the starter rope (Fig. 10).To avoid serious
! injury, the operator and unit must be in a stable position while starting.
STARTING iNSTRUCTiONS
1. Mix gas with oil. See Oil and
Fuel Mixing Instructions.
2. Fill the fuel tank with the
fuel/oil mixture.
NOTE: There is no need to turn
the unit on. The On/Off
Control is in the ON ( I)
position at all times (Fig. 7).
3. Fully press and release the
primer bulb 10 times, slowly.
Some amount of fuel should
be visible in the primer bulb
and fuel lines (Fig. 8). If fuel
can not be seen inthe bulb,
press and release the bulb as
many times as it takes until
/
fuel can be seen in it.
4. Flip the choke lever clockwise
until it clicks (Fig. 9).
5. Crouch in the starting position
(Fig. 10). Do not squeeze the
throttle. Pull the starter rope
with a controlled motion until
the unit starts.
6. Waitand allow the unit to idlefor
5 - 10 seconds. Ifthe unit stops
running during this time, squeeze Choke LeverJ
the throttle control and pullthe
starter rope in a controlled
motion until the unit starts.
7. Squeeze and hold the throttle
control for 30 to 60 seconds to
allow the unit to warm up.
NOTE: The unit uses the
INCREDI=PULL TM starting
system, which significantly
reduces the effort required
to start the engine. The
starter rope must be
pulled out far enough to
hear the engine attempt to
start. There is no need to / =qu,pp_o,,m\
pull the rope briskly-- there I_-P_L4g/Jd _
is no harsh resistance ........................
when pulling. Be aware _ncr_!-Pu.
that this starting method is
vastly different from (and
much easier than) what
you may be used to.
IF,.. The engine does not start,
go back to step 3.
NOTE: Ifthe unit is hot and fails
to start within 3 pulls of
off (o)-__
_(_ Throttle
Control
Fig. 7
Primer
Bulb
Fig. 8
Fig. 9
Starting
Position
Fig. 10
the starter rope, squeeze the throttle control and pull the starter rope
until the unit starts.
STOPPING INSTRUCTIONS
1. Release the throttle control and allow the engine to cool down by idling.
2. Press and hold the On/Off Control in the OFF (O) position until the
engine comes to a complete stop (Fig. 7).
HOW TO START THE UNIT USING THE PLUG=IN POWER START OR
POWER BiT START ACCESSORY
NOTE= This unit can use a Plug-in Power Start or Power Bit Start
optional accessory!
Please refer to the Plug-In Power Start or Power Bit Start operator's
manual for proper use of this feature. (Items Sold Separately! Please
refer to page 9 of this manual about purchasing these accessories.)
STARTING INSTRUCTIONS
1. Mix gas with oil. See Oil and Fuel Mixing Instructions.
2. Fill the fuel tank with the fuel/oil mixture.
NOTE: There is no need to turn the unit on. The On/Off Control is in the
ON (I) position at all times (Fig. 7).
3. Fully press and release the primer bulb 10 times, slowly. Some amount of
fuel should be visible in the primer bulb and fuel lines (Fig. 8). If fuel can not
be seen in the bulb, press and release the bulb as many times as it takes
until fuel can be seen in it.
4. Flip the choke lever clockwise until it clicks (Fig. 9).
5. Crouch in the starting position (Fig. 10). Do not squeeze the throttle. Place
the Plug-In Power Start or Power Bit Start into the back of the unit.
Refer to the Operation section of the Plug-In Power Start or Power Bit
Start operator's manual.
6. Press and hold the ON (I)button of the Plug-in Power Start or Power Bit
Start equipped drill in intervals no longer than 4 seconds each until the
unit starts.
7. Wait and allow the unit to idle for 5 - 10 seconds. Ifthe unit stops running
during this time, squeeze the throttle control, then press and hold the ON (I)
button of the Plug-in Power Start or Power Bit Start equipped drill in intervals
no longer than 4 seconds each until the unit starts.
8. Remove the Plug-In Power Start or drill from the unit.
9. Squeeze and hold the throttle control for 30 to 60 seconds to allow the
unit to warm up.
IF,.. The engine does not start, go back to step 3.
IF,.. The engine fails to start after a few attempts, squeeze the throttle
control, then press and hold the Plug-In Power Start or drill ON (I)
button in intervals no longer than 4 seconds each until the unit starts.
STOPPING INSTRUCTIONS
1. Release the throttle control and allow the engine to cool down by idling.
2. Press and hold the On/Off Control in the OFF (O) position until the
engine comes to a complete stop (Fig. 7).
HOLDING THE UNIT
-- i_L_ ARNING: Always wear eye, hearing, foot and body protection
to reduce the risk of injury when operating this unit.
Before operating the unit, stand in
the operating position (Fig. 11).
Check for the following:
The operator is wearing eye
protection and proper clothing
With a slightly-bent right arm,
the operator's hand is holding
the shaft grip
The operator's left arm is
straight, the left hand holding
the D-handle
The unit is at waist level Fig. 11'_
The cutting head is parallel to
the ground and easily contacts the grass without the need to bend over
ADJUSTING TRIMMING LINE LENGTH
_ WARNING: Do not remove or alter the line cutting blade |
/
assembly. Excessive line length will cause premature engine
J
failure and / or unit damage.
The Bump HeadTM cutting head
allows the release of trimming line
without stopping the engine. To
release more line, lightly tap the
cutting head on the ground (Fig. 12)
while operating the unit at high
speed.
NOTE: Always keep the
trimming line fully
extended. Line release
becomes more difficult "_
when the cutting line
gets shorter. Fig. 12
Each time the head is bumped, about 1 inch (25.4 mm) of trimming line
releases. A blade in the cutting head shield will cut the line to the proper
length if any excess line is released.
Forbestresults,tapthebumpknobonbaregroundorhardsoil.If
attemptingalinereleaseintallgrass,theenginemaystall.
NOTE:DonotresttheBumpHeadTM on the ground while the unit is running.
Some line breakage will occur from:
Entanglement with foreign matter
Normal line fatigue
Attempting to cut thick, stalky weeds
Forcing the line into objects such as walls or fence posts
TIPS FOR BEST TRIMMING RESULTS
Keep the cutting head parallel to the ground.
Do not force the cutting head. Allow the tip of the line to do the cutting,
especially along walls. Cutting with more than the tip will reduce cutting
efficiency and may overload the engine.
Cut grass over 8 inches (200 mm) by working from top to bottom in small
increments to avoid premature line wear or engine drag.
Cut from right to left whenever possible. Cutting to the left improves the
unit's cutting efficiency. Clippings are thrown away from the operator.
Slowly move the unit into and out of the cutting area at the desired height.
Move either in a forward-backward or side-to-side motion. Cutting shorter
lengths produces the best results.
Trim only when grass and weeds are dry.
The life of the cutting line is dependent upon:
Following the trimming techniques
What vegetation is being cut
Where vegetation is cut
For example, the line will wear
faster when trimming against a
foundation wall as opposed to
trimming around a tree.
DECORATIVE TRIMMING
Decorative trimming is
accomplished by removing all ;300
vegetation around trees, posts,
fences, etc.. _
Rotate the whole unit so that the
cutting head is at a 30° angle to Fig. 13
the ground (Fig. 13).
MAINTENANCE SCHEDULE
WARNING: To prevent serious injury, never perform
maintenance or repairs with unit running. Always service and
repair a cool unit. Disconnect the spark plug wire to ensure that
the unit cannot start.
Perform these required maintenance procedures at the frequency stated in
the table. These procedures should also be a part of any seasonal tune-up.
NOTE: Some maintenance procedures may require special tools or skills. If
unsure about these procedures take the unit to Craftsman or other
qualified service dealer. Call 1-800-4-MY-HOME ®for more information.
NOTE: Maintenance, replacement, or repair of the emission control devices
and system may be performed by a Craftsman or other qualified
service dealer. Call 1=800=4=MY-HOME ®for more information.
FREQUENCY MAINTENANCE REQUIRED SEE
Before starting engine Fill fuel tank with fresh fuel p. 5
Every 10 hours Clean and re-oil air filter p. 8
Every 25 hours Check spark plug condition and gap p. 8
LINE INSTALLATION
-- ]WARNING: Never use metal-reinforced line, wire, chain or
rope. These can break off and become dangerous projectiles.
This section covers both SplitLine® and standard single line installation.
Always use original equipment manufacturer 0.095 in. (2.41 ram}
replacement line. Line other than the specified may make the engine
overheat or fail.
7
There are two methods to replace
the trimming line:
Wind the inner reel with new line
Install a prewound inner reel
Removing the Existing inner Reel
1. Hold the outer spool with one
hand and unscrew the bump
knob counterclockwise (Fig.
14). Inspect the bolt inside the
bump knob to make sure it
moves freely. Replace the
bump knob if damaged.
2. Remove the inner reel from
the outer spool (Fig. 15).
3. Remove spring from the
inner reel (Fig. 15).
4.
Use a clean cloth to clean \ ,.
the inner reel, spring, shaft,
and inner surface of the outer_
spool.
Check the indexing teeth on
the inner reel and outer spool
for wear (Fig. 16). If
necessary, remove burrs or
replace the reel and spool.
NOTE: Always use the correct
line length when
installing trimming line
on the unit. The line may
not release properly if
the line is too long.
Single Line installation
Go To Step 8 for SplitLine®
Installation:
6. Take approximately 20 feet (6
m) of new trimming line, loop
it into two equal lengths.
Insert each end of the line
through one of the two holes
in the inner reel (Fig. 17). Pull
the line through the inner reel
so that the loop is as small
as possible.
7. Wind the lines in tight even
layers onto the reel (Fig. 18).
Wind the line in the direction
indicated on the inner reel.
Place an index finger
between the two lines to stop
the lines from overlapping.
Do not overlap the ends of
the line. Proceed to step 12.
SplitUne® installation
8. Take approximately 10 feet (3
m) of new trimming line. Insert
one end of the line through
one of the two holes inthe
inner reel (Fig. 19). Pull the
line through the inner reel until
only about 4 inches is left out.
9. Insert the end of the line into
the open hole in the inner
reel and pull the line tight to
make the loop as small as
possible (Fig. 19).
10. Before winding, split the line
Bump Knob
Fig. 14
Outer
Spool
Spring
Inner Reel
Fig. 15
Indexing Teeth
Fig.16
Loop
Fig. 17
Fig. 18
back about 6 inches. , _
11. Wind the line in tight even
layers in the direction ._
indicated on the inner reel. /H/i/
NOTE: Failure to wind the line in
the direction indicated will
cause the cutting head to
operate incorrectly.
Loop
Fig. 19
12. Insert the split ends of the
line into the two holding slots
(Fig. 20).
13. Insert or slide the split ends
of the line through or into the
eyelets in the outer spool
place inner reel with spring
inside the outer spool (Fig.
21). Push the inner reel and
outer spool together.
NOTE: The spring must be
assembled on the inner
reel before reassembling
the cutting head.
14. While holding the inner reel
and outer spool, grasp the
split ends and pull firmly to
release the line from the
holding slots in the spool.
15. Hold the inner reel in place
and install the bump knob by
turning clockwise. Tighten
securely.
INSTALLING A PREWOUND REEL
Index Teeth
Fig. 20
Eyelets
1. Hold the outer spool with one
hand and unscrew the bump Fig. 21
knob counterclockwise (Fig. 14). Inspect the bolt inside the bump knob to
make sure it moves freely. Replace the bump knob if damaged.
2. Remove the old inner reel from the outer spool (Fig. 15).
3. Remove the spring from the old inner reel (Fig. 15).
4. Place the spring in the new inner reel.
NOTE: The spring must be assembled on the inner reel before
reassembling the cutting head.
5. Insert or slide the ends of the line through or into the eyelets in the outer
spool (Fig. 21).
6. Place the new inner reel inside the outer spool. Push the inner reel and
outer spool together. While holding the inner reel and outer spool, grasp the
ends and pull firmly to release the line from the holding slots in the spool.
7. Hold the inner reel in place and install the bump knob by turning
clockwise. Tighten securely.
AiR FILTER MAINTENANCE
Cleaning the Air Filter
Clean the air filter every 10 hours
of operation. It is an important item
to maintain. Failure to maintain the
air filter properly can result in poor
performance or can cause
permanent damage to the engine.
1. Open the air filter cover by
pressing the lock tab in and
pulling out on the air filter
cover (Fig. 22).
2. Remove the air filter (Fig. 22).
3. Wash the filter in detergent and
water (Fig. 23). Rinse the filter
thoroughly and allow it to dry.
4. Apply enough clean SAE 30
motor oil to lightly coat the
filter (Fig. 24).
5. Squeeze the filter to spread
and remove excess oil (Fig. 25).
6. Replace the air filter into the
air filter cover (Fig. 22).
NOTE: Operating the unit
without the air filter
WILL VOID the warranty.
7. Close the air filter cover by
swinging it to the left and
then pressing it down until
the lock tab snaps into place
(Fig. 22).
CARBURETOR ADJUSTMENT
NOTE: Careless adjustments
can seriously damage
the unit. Contact a
Craftsman or other
qualified service dealer
to make carburetor
adjustments.
Call 1-800=4=MY-HOME ®
for more information.
Air Filter Cover
Lock Tab
Air Filter
Fig. 22
<
Fig. 23
Fig. 24
REPLACING THE SPARK PLUG
Use a Champion RDJ7J or a
replacement part #753-06193
spark plug (or equivalent). Remove
the plug after every 25 hours of
operation and check its condition.
1. Stop the engine and allow it
to cool. Grasp the plug boot
firmly and pull it from the
spark plug. Fig. 25
2. Clean around the spark plug.
Remove the spark plug from the cylinder head by turning a 5/8-inch
socket counterclockwise.
m
_L_ ARNING: Do not sand blast, scrape or clean spark plug
electrodes. Grit in the engine could damage the cylinder.
3.
4.
Replace a cracked, fouled or dirty spark plug. Set the air gap at 0.025
in. (0.635 rnrn) using a feeler gauge (Fig. 26).
Install a correctly-gapped spark plug in the cylinder head. Tighten by
turning the 5/8-inch socket clockwise until snug. If using a torque
wrench, torque to:
110=120 in.olb. (12.3=13.5
0.025 in.
(0.635ram) t
Fig. 26
Norn}. Do not over-tighten.
5. Reattach the plug boot.
TRANSPORTING
Allow the engine to cool before transporting.
Drain fuel from unit.
Tighten fuel cap before transporting.
WARNING: To avoid serious personal injury,always turn the unit off I
and allow it to cool before cleaning or maintaining it. |
J
Secure the unit while transporting.
CLEANING
Use a small brush to clean offthe outside of the unit. Do not use strong
detergents. Household cleaners that contain aromatic oils such as pine and
lemon, and solvents such as kerosene, can damage plastic housing or handle.
Wipe off any moisture with a soft cloth.
STORAGE
Never store afueled unit where fumes may reach anopen flame or spark.
Allow the engine to cool before storing.
Store the unit locked up to prevent unauthorized use or damage.
Store the unit in a dry, well-ventilated area.
Store the unit out of the reach of children.
LONG TERM STORAGE
If planning on storing the unit for an extended time, use the following storage
procedure:
1. Carefully drain the fuel tank by running the unit dry or remove fuel cap
and tip the motor housing over and drain oil/gas fuel into a container
with the same 2-cycle fuel mixture. Do not use fuel that has been stored
for more than 30 days.
2. Start the engine and allow it to run until it stalls. This ensures that all
fuel has been drained from the carburetor.
3. Allow the engine to cool. Remove the spark plug and put 1 oz. (30 ml)
of any high quality motor oil or 2-cycle oil into the cylinder. Pull the
starter rope slowly to distribute the oil. Reinstall the spark plug.
NOTE: Remove the spark plug and drain all of the oil from the cylinder before
attempting to start the trimmer after storage.
4. Thoroughly clean the unit and inspect it for any loose or damaged
parts. Repair or replace damaged parts and tighten loose screws, nuts
or bolts. The unit is ready for storage.
PLUG=IN POWER START AND POWER BiT START FEATURES
This unit can be started with an optional Plug-In Power Start or Power Bit
Start (items sold separately). If choosing to start the unit using one of these
features or have questions, please contact your local Craftsman retailer or
call 1=800=4=MY=HOME® for more information and purchasing. You may
also go to www.craftsrnan.corn.
Power Start Feature
item No. Description
316.85951 ..................................... Plug-In Power Start
316.85952 ........................................ Power Bit Start
9
Empty fuel tank
Engine is flooded
Fouled spark plug
Air filter is plugged
Improper carburetor adjustment
Old or improperly mixed fuel
Dirty air filter
Old or improperly mixed fuel
Fouled spark plug
Engine overspeed protection engaged
Cutting head bound with grass
Inner reel bound up
Line welded
PROBLEM SOLUTION
Fill fuel tank with properly mixed fuel
Pull the starter rope while holding the throttle control
Replace the spark plug
Replace or clean the air filter
Take to a Craftsman or other qualified service dealer for adjustment
Drain fuel tank and add fresh fuel mixture
Clean or replace the air filter
Drain fuel tank and add fresh fuel mixture
Replace the spark plug
Allow the engine to cool down for 10 minutes before restarting
Stop the engine and clean cutting head
Rewind the inner reel
Disassemble, remove the welded section and rewind
Not enough line is exposed Push the bump knob and pull out line until 4 inches (102 mm) of line is
outside of the cutting head
Oil, cleaner or lubricant in cutting head Clean and thoroughly dry the cutting head
HELP.
f.......
........... ! i_
YOu,,K find the answer and raore on mana_emvhfe°com - for free.
=
Find this and al your other product manuats onfne.
=
Get answers from our team of home experts.
= Get a personatzed maintenance ptan for your home.
=
Find information and tools to help with home projects.
.......... i
10
Engine Type ................................................................................................... Air-Cooled, 2-Cycle
Stroke ........................................................................................................... 1.10 in. (2.8 cm)
Displacement ............................................................................................................. 27 cc
Operating RPM ....................................................................................................... 6,800+ rpm
Idle Speed RPM ................................................................................................. 2,800 - 3,400 rpm
Ignition Type ........................................................................................................... Electronic
Ignition Switch ..................................................................................................... Rocker Switch
Spark Plug Gap ................................................................................................ 0.025 in. (0.635 mm)
Lubrication ....................................................................................................... Fuel/Oil Mixture
Fuel/Oil Ratio ............................................................................................................... 40:1
Carburetor ................................................................................................. Diaphragm, All-Position
Starter ........................................................................................... Incredi-Pull TM Starting Auto Rewind
Muffler ........................................................................................................ Baffled with Guard
Throttle ..................................................................................................... Manual Spring Return
Fuel Tank Capacity ................................................................................................ 14 fl.oz. (414 ml)
Drive Shaft Housing ............................................................................. Steel Tube (Craftsman® Convertible TM)
Throttle Control .................................................................................................. Finger-Tip Trigger
Approximate Unit Weight (No fuel, with cutting attachment, shield and D-handle) ................................................. 10 Ibs. (4.5 kg)
Cutting Mechanism .................................................................................................... Bump Head
Line Spool Diameter ................................................................................................. 3 in. (76.2 mm)
Trimming Line Diameter .......................................................................................... 0.095 in. (2.41 mm)
Cutting Path Diameter .............................................................................................. 16 in. (40.64 cm)
* All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without
notice.
REPAIR PROTECTION AGREEMENTS
Congratulations on making a smart purchase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like all
products, it may require repair from time to time. That's when having a Repair Protection Agreement can save you money and aggravation.
Here is what the Repair Protection Plan Agreement includes:
[] Expert service by our 10,000 professional repair specialists
[] Unlimited service and no charge for parts and labor on all covered repairs
[] Product replacement up to $1500 if your cover product can not be fixed
[] Discount of 10% from regular price of service and related installed parts not covered by the agreement; also, 10% off regular price of
preventive maintenance checks
[] Fast help by phone - we call it Rapid Resolution - phone support from a Sears representative. Think of us as a "talking owner's
manual."
Once you purchase the Repair Protection Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or
schedule a service appointment online.
The Repair Protection Agreement is a risk-free purchase. Ifyou cancel for any reason during the product warranty period, we will provide a full refund. Or a prorated
refund anytime after the product warranty period expires. Purchase your Repair Protection Agreement today!
Some limitations and exclusions apply. For prices and additional information call 1=800=827=6655.
*Coverage in Canada varies on some items. For full details call Sears Canada at 1=800=361 =6665.
Sears installation Service
For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, inthe U.S.A. or Canada call 1-800-4-MY-HOME ®.
11
12
Manual del Operador
MRN
2-Tiempos
WEEDWACKER_
RECORTADOR A GASOLINA
Model No. 316.791081
#_f_.t_Sf_" STA_NG _A $E _'
o SEGURIDAD
MONTAJE
FUNCIONAMIENTO
MANTENIMIENTO
LISTADO DE PIEZAS
PRECAUCION: Lea el manual
del operador y siga todas las
advertencias e instrucciones
de seguridad.
Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.
Visite nuestro sitio web: www.craftsman.com
769-06126 P00 06/10
PROPOSICION 65 DE CALiFORNiA
LAS EMISIONES DEL MOTOR DE ESTE PRODUCTO CONTIENEN
SUBSTANCIAS QUIMICAS QUE EL ESTADO DE CAMFORNIA CONOCE
COMO CAUSANTES DECANCER, DEFECTOS DE NACIMIENTO U OTROS
DAI_IOSREPRODUCTIVOS.
INDICE DE CONTENIDOS
Normas para una operaci6n segura .............................. 14
Garantia ................................................... 16
Conozca su unidad ........................................... 16
Instrucciones de ensamble ..................................... 16
Informaci6n del aceite y del combustible .......................... 17
Instrucciones de arranque y apagado ............................ 18
Instrucciones de operaci6n .................................... 19
Instrucciones de mantenimiento y reparaci6n ...................... 19
Limpieza y almacenamiento .................................... 21
Resoluci6n de problemas ...................................... 22
Especificaciones ............................................. 23
Lista de piezas .............................................. 30
Numeros de servicio ................................ Contraportada
PARACHNSPAS
NOTA: Para los usuarios en tierras ferestales de los EE.UU. yen los estados de
California, Maine, Oregon y Washington. Todos losterrenos forestales de los EE.UU.
y el estado de California (C6digos de Recursos PQblicos 4442 y 4443), Oregon y
Washington, requierenpot decreto, que ciertos motores de combusti6n interna que se
hagan funcionar en zonas boscosas y/o zonas cubiertas por pastizales, esten
equipados con un parachispas, que sean mantenidos en buen estado de
funcionamiento o que el motor sea construido, este equipado y sea mantenido para
evitar incendios. Consulte los reglamentos pertinentes a esos requisitos con las
autoridades estatales o locales. El incumplimiento de esos requisitos puede
responsabilizarle o someterle a la imposici6n de una multa. Esta unidad rue equipada
en la f_brica con un parachispas. Si requiere sustituci6n, hay una Pantalla
Parachispas disponible, Pieza #753-06182 al contactar eldepartamento de servicio.
Los simbolos de seguridad se utilizan para Ilamar su atenci6n sobre posibles
peligros. Los simbolos de seguridad y sus explicaciones merecen toda su
atenci6n y comprensi6n. Los simbolos de seguridad no eliminan ningQn peligro
por s[ mismos. Las instrucciones o advertencias que ofrecen no substituyen
las medidas adecuadas de prevenci6n de accidentes.
SIMBOLO SIGNIFICADO
ALERTA DE SEGURIDAD: Indica peligro, advertencia o
precauci6n. Debe prestar atenci6n para evitar sufrir graves lesiones
personales. Puede set utilizado junto con otros simbolos o figuras.
NOTA: Le ofrece informaci6n o instrucciones que son esenciales para la
operaci6n o mantenimiento del equipo.
PELIGRO: El no obedecer una advertencia de seguridad puede
conducir a que usted u otras personas sufran graves lesiones. Siga
siempre las precauciones de seguridad para reducir el riesgo de
incendio, descarga electrica y lesiones personales.
ADVERTENCIA" El no seguir una advertencia de seguridad
puede conducir a que usted u otras personas sufran lesiones. Siga
siempre las precauciones de seguridad para reducir el riesgo de
incendio, descarga electrica y lesiones personales.
PRECAUCION: El no seguir una advertencia de seguridad
puede conducir a da_o patrimonial o a que usted u otras
personas sufran lesiones personales. Siga siempre las
precauciones de seguridad para reducir el riesgo de incendio,
descarga el6ctrica y lesiones personales.
NOTA: iEsta unidad puede utilizar un arrancador de potencia
electrico o el accesorio optional accesorio arrancador de
potencia para taladro!
Para informarse sobre el uso adecuado de estos sistemas, consulte
el manual del operador del arrancador de potencia electrico o del
accesorio opcional accesorio arrancador de potencia para taladro.
i(Articulos vendidos por separado)! Vea en la p&gina 21 de este
manual mAs informaci6n sobre estos accesorios).
Lea el manual del operador y siga todas las advertencias e instrucciones
de seguridad. De no hacerlo, el operador y/o los espectadores pueden
sufrir graves lesiones.
Sl TIENE PREGUNTAS, LLAME AL 1=800-4=MY=HOME®
Toda la informaci6n, las ilustraciones y las especificaciones contenidas en este
manual se basan en la informaci6n mAs reciente disponible en el momento de
impresi6n del manual. Nos reservamos el derecho de hacer cambios en cualquier
momento sin aviso previo.
IMPORTANTE INFORMACION DE SEGURiDAD
LEA TODAS LAS INSTRUCCIONES ANTES DE OPERAR LA UNIDAD
ADVERTENClA: AI utilizarlaunidad, debe observar las reglasde
seguridad. Lea estas instrucciones antes de operar la unidad afin de
garantizar la seguridad del operador y cualquier transeQnte.Guardeestas
instrucciones parauso posterior.
Lea las instrucciones cuidadosamente. Familiaricese con los controles y
el uso adecuado de la unidad.
No opere esta unidad cuando est6 cansado, enfermo o bajo la influencia
de alcohol, drogas o medicamentos.
Los ni_os y los adolescentes menores de 15 a_os de edad no deben usar la
unidad. Los adolescentes pueden hacerlo bajo la supervisi6n de un adulto.
Todos los dispositivos de protecci6n y los accesorios de seguridad
deben estar instalados adecuadamente antes de operar la unidad.
Inspeccione la unidad antes de usarla. Reemplace las piezas daSadas.
Verifique si hay fugas de combustible. AsegQrese de que todos los
fijadores est6n en su lugar y asegurados. Reemplace las piezas que
est6n agrietadas, astilladas o daSadas en cualquier forma. No opere la
unidad con piezas sueltas o daSadas.
Inspeccione cuidadosamente el Area antes de operar la unidad. Elimine todos
los escombros y los objetos duros o filosos tales como cristal, alambre, etc.
Est6 consciente del riesgo de lesi6n en la cabeza, las manos y los pies.
No permita niSos, espectadores ni mascotas en el Area. Los niSos, los
espectadores y las mascotas deben estar fuera de un radio de 50 pies
(15 m.) come minimo; de todas formas los espectadores correrAn el
riesgo de ser golpeados per objetos lanzados pot la unidad. Se debe
exhortar a los espectadores a que usen protecci6n para los ojos. Si se le
acerca alguien apague la unidad de inmediato.
Use s61olinea de reemplazo del fabricante original del equipo con un diAmetro
de 0.095 de pulgada (2.41 mm). Nunca use linea reforzada con metal, alambre
o soga. Se pueden romper y convertirse en proyectiles peligrosos.
Optima el control del estrangulador y compruebe que regresa
automaticamente a la posici6n de marcha en vacio. Haga todos los
ajustes o reparaciones antes de usar la unidad.
AVlSOS DE SEGURIDAD PARA LAS UNIDADES QUE FUNCIONAN CON
GASOLINA
[_ ADVERTENClA: La gasolina es muy inflamable y sus gases
pueden explotar si se encienden. Tome las siguientes precauciones:
Almacene el combustible solamente en recipientes diseSados y aprobados
especificamente para el almacenamiento de dichos materiales.
Pare siempre el motor y deje que se enfrie antes de Ilenar el tanque de
combustible. Nunca quite la tapa del tanque de combustible, ni agregue
combustible, cuando el motor est6 caliente. Siempre afloje la tapa del
tanque de combustible lentamente para aliviar cualquier presi6n que
haya en el tanque antes de cargar combustible. No fume.
Siempre mezcle y agregue el combustible en un Area exterior bien
ventilada, donde no haya chispas ni llamas. No fume.
Nunca opere la unidad sin la tapa de combustible bien colocada en su lugar.
Evite crear una fuente de ignici6n para el combustible derramado. Limpie
de la unidad inmediatamente cualquier combustible derramado antes de
arrancar el motor. Mueva siempre la unida a 30 pies (9.1 m) como minimo
de la fuente y sitio de combustible antes de arrancar el motor. No fume.
Nunca arranque ni use la unidad dentro de una habitaci6n o edificio
cerrado. Respirar los vapores de escape puede causarle la muerte. Opere
esta unidad s61o en un Area exterior bien ventilada.
14
CUANDO ESTI_ OPERANDO No opere el motor a mas veloctdad de la necesana para cortar, recortar o
Nunca arranque ni opere la unidad dentro de un cuarto o edlficto cerrado.
Resptrar los vapores del escape puede ser fatal. Slempre opere esta
unidad solamente en un Area exterior bten ventllada.
Use galas protectoras que cumplan con la norma Z87.1-1989 de ANSI y
tengan la marca que Io indic& Use protecct6n para la oreja/audtct6n
cuando opere esta unidad. Use mascara factal o para polvo sl la
operact6n produce mucho polvo.
Use pantalones largos fuertes, botas, guantes y camisa de mangas
largas. No use ropa holgada, joyas, pantalones cortos, sandahas, ni este
descalzo. AsegL'4reseel cabello per enctma del novelde los hombres.
,, El protector del accesono de corte debe estar slempre co!ocado cuando
se utlhce la unidad como recortador. No opere la unidad sin ambas lineas
de corte extendldas y con la linea adecuada instalada. No extlenda la
linea de corte mas alia de la Iongitud del protector.
,, Aseg0rese de que el accesono de corte no estA en contacto con ningL'm
objeto antes de arrancar la unldad.
,, Ajuste la posict6n de la D-manija para facthtar el mejor agarre.
,, El accesono de corte puede estar girando durante los ajustes del
carburador. Use ropa que Io proteja y cumpla con todas las instrucctones
de segundad para prevenir graves lesiones personales.
,, Use la unidad solamente de dia o con buena luz artlfictal.
,, Evlte arranques accldentales. Este elmla poslct6n de arranque cada vez que
hale la cuerda de arranque. El operador y la unldad deben estar elmuna
poslct6n estable al arrancar. Consulte las Instrucctones de Arranque/Parada.
,, Use la herramienta correcta. Use esta herramienta solamente para el
proposito para el cual fue dtsel_ada.
,, No se estlre demaslado. Mantenga slempre la base de apoyo y eqL4ilibno
adecuados.
,, Sostenga slempre la unidad con ambas manes cuando la opere. Mantenga
un agarre flrme sobre ambas manljas.
,, Mantenga las manos, la cara y los ptes alejados de todas las partes en
mowmiento. No toque nitrate de parar el accesono de corte cuando este
girando.
,, No toque el motor, la caja de engranajes ni el sllenctador. Estas piezas
estan muy cahentes durante la operact6n, incluso despues de que se
apaga la unidad.
recortar bordes. No haga functonar el motor a alta veloctdad cuando no
este cortando.
,, Esta unidad tlene un interruptor de la protecct6n de la veloctdad excesiva
para guardar la unidad del recalentamiento. Cuando la unidad se functona
con en la valvula reguladora Ilena mientras que es parada para las
longitudes del tlempo extendtdas que el interrupter de la protecct6n de la
veloctdad exceswa dedicara.
,, Pare siempre el motor cuando deje de cortar o cuando este caminando
de un lugar de corte hacta otro.
,, St golpea o se enreda con un objeto extral_o, pare el motor
inmedtatamente y venfique sl ha habtdo algL]n dal_o. No Io opere antes de
reparar el da_o. No opere la unidad con piezas sueltas o da_adas.
,, Pare la unidad, apague el motor y desconecte la bujia para mantenimiento
o reparact6n.
,, Utlhce L]nicamente ptezas de repuesto y los accesorios que figuran en la
secct6n de la Ltsta de Ptezas de este manual del operador y distribuldos
por una toma de Craftsman o centro de serwcto. El uso de cualquier pleza
de repuesto o accesonos comprados en otro lugar puede ser pehgroso y
anulara la garantia.
Mantenga la unidad hmpta de vegetact6n y otros materlales. Pudleran
quedar obstruidas entre e! accesorio de corte y el protector.
Para reductr el pehgro de incendlo, mantenga el motor y el sllenctador
hbre de hierba, hojas, exceso de grasa o acumulact6n de carbon.
OTROS AVJSOS DE SEGURIDAD
,, Nunca almacene una unidad con combustible dentro de un ediflcto en el
cual los vapores puedan Ilegar a una llama expuesta o una chispa.
,, Deje que el motor se enfne antes de almacenarlo o transportarlo.
AsegL'_resede fijar bten la unidad mientras la transporta.
,, Almacene la unidad en un Area seca y cerrada, o elmun lugar alto para evltar
use no autonzado o da_os. Mantengala alejada del alcance de los ni_os.
,, Nunca rocie nl chorree la unidad con agua nl ning0n otro liquido.
Mantenga las manljas secas, limptas y hbres de escombros. Limptela
despues de usarla, vea las instrucctones de Ltmpteza y Almacenamtento.
,, Conserve estas instrucctones. ConsL]ltelas con frecuencta y L]selas para
instruir a otros usuarios. Si le presta esta unidad a alguien, prestele
tambten estas _nstrucctones.
CONSERVE ESTAS INSTRUCCIONES
SIMBOLOS DE SEGURIDAD E INTERNACIONALES
Este manual del operador describe los simbolos y flguras de segundad e internactonales que pueden aparecer en este producto. Lea el manual del operador
para obtener informact6n completa acerca de la segundad, ensamble, operact6n y mantenimiento y reparact6n.
SIMBOLO SIGNIFICADO SIGNIFICADO
_ SIMBOLO DE ALERT,& DE SEGURIDAD
Jnd=capeligro, advertencla o precaucm6n. Puede set utlhzado
junto con otros sJmbolos o f_guras.
@
o
ADVERTENCIA- LEA EL MANUAL DEL OPERADOR
Lea el manual deJoperador y slga todas las advertencias e
instrucciones de segundad. De no hacerlo, el operador yio los
espectadores pueden sufrir graves lesiones.
USE PROTECCJON OCULAR Y AUDITIVA
ADVERTENCIA: Losobjetos arrojados por la unldad y el
ruldo fuerte pueden causar graves les_onesoculares y p_rdlda
auditiva. Utihceprotecci6n ocular que curnpla con lasnormas ANSI
Z87.1989 y protecci6n auditiva cuando opere estaunJdad.Use una
careta completa cuando la neces_te.
I_ M _ I" COMBUSTIBLE SiN PLOMO
Use saempre combustible hmplo, nuevo y sin plomo.
i ONTROL DE ENCENDIDO Y APAGADO
ENCENDIDO/ARRANQUE/MARCHA
i ONTROL DE ENCENDIDO Y APAGADO
APAGADO o PARAD©
LOS OBJETOS DESPEDIDOS Y LA CUCNILLA ROTATJVA
PUEDEN CAUSAR GRAVES LESJONES
ADVERTENCIA: NO opere esta unldad sl la proteccl6n
plAstlca de linea no esta colocada en su lugar. Mantengase
alejado del accesono de corte g_ratono.
MANTENGA ALEJADOS A LOS ESPECTADORES
ADVERTENCIA: Mantenga a todos los espectadores, en
especial a n_os y animales dom_sticos a pot Iomenos 50 p_es(15
m) del Areade corte.
ADVERTENCIA DECALIENTE
No toque un sllenciador ni un cJlindro caliente. Puede
quemarse. Estas partes se cahentan mucho con el uso. Luego
de apagarse permanecen cahentes durante un corto hempo.
_NDICADOR DE ACEITE
Consulte e! manual del operador para obtener _nformaci6n acerca
del tlpo correcto de aceite.
BOMB_LLA DEL CEBADOR
Opnma la bomb_lla del cebador completa y lentamente, de
10 veces
CUCHILLA ARLADA
ADVERTENCIA: La protecc_6n del accesorio de torte
cont_ene una cuchilla afilada. Para preven_r graves les_ones,
no toque la cucNla.
15
GARANTIA TOTAL POR 2 AhIOS, DE CRAFTSMAN
Este producto se garantiza DURANTE 2 ANOS a partir de la fecha de compra, contra defectos en el material o en la mano de obra. El producto defectuoso
ser& reparado sin ningOn costo o serA remplazado gratuitamente si no puede ser reparado.
Para conocer los detalles sobre la cobertura de la garantia para que sea reparado o reemplazado, visite el sitio web: www.craftsman.com
Esta garantfa cubre SOLAMENTE defectos en el material o mano de obra. La cobertura de la garantia NO incluye:
Articulos consumibles que se desgasten debido al uso normal dentro del periodo de la garantia, tales como linea de corte, filtros o bujias de encendido.
Da_os que ocurran al producto como resultado de intentos de modificaci6n o reparaci6n por parte del usuario, o que sean causados por accesorios del producto.
Reparaciones necesarias debidas a accidente o falla en el funcionamiento, o por no mantener el producto de acuerdo con todas las instrucciones provistas.
El mantenimiento preventivo, o reparaciones necesarias debido a mezcla incorrecta de combustible, o a combustible viejo o contaminado.
Esta garantia es nula sieste producto se utiliza alguna vez durante la prestaci6n de servicios de tipo comercial o si se le alquila a otra persona.
Esta garantia le otorga a usted derechos legales especificos, y usted puede ademAs poseer otros derechos, los cuales varian de un estado a otro.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
APLICACIONES
Como recortadora;
Corte de cesped y hierbas delgadas
Recorte de bordes
Recorte decorativo alrededor de &rboles, cercos, etc.
Puede usar otros accesorios con la unidad. Lea la lista de accesorios.
Silenciador
Bujia de encendido
Mango del eje
Control de encendido
y apagado
Manija en D
Manija de la cuerda
de arranque
Cubierta
del filtro
de aire
Bastidor dam eje
Tapa del mbustible
Cuchilla de
corte de linea
\
Control del
regulador
ConvertibleTM Bombilla del cebador
acoplador
Cabezal de corte
Protector de cabezal de corte
INSTALACION DEL PROTECTOR DE CABEZAL DE CORTE orificios en el soporte de montaje de la guardera y el protector de
_ ADVERTENCIA: No opere nunca la recortadora sin el |
protector de cabezal de corte colocado en su lugar para evitar
1
graves lesiones personales.
Siga las siguientes instrucciones
si el protector de cabezal de corte
no est& instalado en su unidad.
1. Coloque el protector de
cabezal de corte en el
bastidor del eje. Cerci6rese
de que el soporte de montaje
de la guardera se deslice en
la ranura situada en el borde
del protector de corte. Gire el
protector en sentido
antihorario hasta que quede
en su lugar (Fig. 1). Los
Protector de Soporte de
cabezal de corte montaje de
la guardera
Fig. I
cabezal de corte se alinear&n.
2. Desde el interior del
protector de cabezal de
corte, empuje el perno
cuadrado a trav6s del orificio
hasta que el extremo con
roscas sobresalga a trav6s
del soporte de montaje de la
guardera (Fig. 2).
3. Ponga la arandela en el perno,
y despues atornille la tuerca
de mariposa y apri6tela.
Perno
Fig. 2
Arandela
Tuerca de
mariposa
16
INSTALACION Y AJUSTE DE LA MANIJA EN D
1. Empuje la manija D hacia Mango del eje Bastidor del eje
abajo sobre el bastidor del eje
(Fig. 3). El agujero del perno _Manija en D
hexagonal en la manija debe
quedar en el lado izquierdo.
2. Inserte el perno de la manija Ajuste
en el agujero hexagonal en la
Minimo de
manija y empOjela. Coloque 15,24 crn
la arandela en el perno, (6 pulgadas) Tuerca de
luego enrosque la tuerca de rnariposa
mariposa en el perno. No la Perno _ Arandela
apriete hasta que haya
ajustado la manija. Fig.3
3. Gire la manija en D para colocar el mango sobre la parte superior del
bastidor del eje. Col6quela a una distancia minima de 6 pulgadas
(15.24 cm) del extremo del mango del eje.
4. Mientras sostiene la unidad en la posici6n de funcionamiento (Fig. 11),
coloque la manija en Den el lugar que le brinde el mejor agarre.
5. Apriete la tuerca de mariposa hasta que la manija en D quede firme.
OPERACION DEL SISTEMA DEL ACOPLADOR CONVERTIBLE TM
ADVERTENCIA: Antes de comenzar a usar este accesorio,
lea y comprenda el manual que viene con el accesorio. Siga toda
J
a nformac 6n de segur dad conten da ene m smo.
El sistema del acoplador Convertible TM le permite el uso de estos accesorios
optativos.
Recortador de bordes de c6sped
Cultivador
Turbo soplador
Cortamalezas
Sierra de poste
Recortador de setos
INSTALACION DEL ACCESORIO DE CORTE U OTROS ACCESORIOS
m i_ DVERTENClA: Para evitar graves lesiones personales,
apague la unidad antes de sacar o instalar accesorios.
_ PREOAUOION: Antes de operar esta unidad, cercidrese 1
de que el bot6n de liberaci6n est6 completamente encajado en el
orificio principal y de que la perilla de ajuste est6 firmemente apretada.
NOTA:
1.
2.
Para facilitar la
instalaci6n o remoci6n Hoyo primario__
de los accesorios, \
coloque la unidad sobre _ \
el suelo o sobre un "_ '_.--9_'_
banco de trabajo. /t I _Y4 I ,, _q--_
eire la perilla en sentido ,,_,_ h--_-_'_ _
antihorario para aflojarla (Fig. 5). ___i--- _-
A la vez que sostiene Bastidor del _ "
firmemente el accesorio,
empOjelo derecho hacia el
interior del acoplador
Convertible TM hasta que el
bot6n de desconexi6n
encaje s61idamente en el
orificio principal (Fig. 4).
NOTA: La alineaci6n del bot6n
de desconexi6n con el
hueco de guia facilitarA
la instalaci6n (Fig. 6).
3. Gire la perilla en sentido
horario para ajustarla (Fig. 5).
Para realizar recortes decorativos
con el accesorio de corte de
cabezal de linea u otro accesorio,
eje superior
Bastidor del
eje inferior
Fig. 4
Orificio lateral 90°
Fig. 5
Perilla
trabe el bot6n de desconexi6n del accesorio de corte u otro accesorio en el
interior del agujero de 90° (Fig. 5).
COMO SACAR EL ACCESORIO DE CORTE U OTRO ACCESORIO
1. Gire la perilla en sentido Acoplador de Bot6n de desconexi6n
antihorario para aflojarla (Fig. 5). ConvertibleTM
2. Opima y sostenga el bot6n , X,_. --/m-
de desconexi6n (Fig. 6).
3. A lavez que sujeta la caja del
eje superior, tire del accesorio __
recto hacia afuera del
acoplador Convertible TM (Fig.
4).
Hueco de guia
Fig. 6
INSTRUCCIONES PARA MEZCLAR EL ACEITE Y ELCOMBUSTIBLE
El combustible viejo o mal mezclado son los motivos principales del mal
funcionamiento de la unidad. AsegQrese de usar combustible nuevo, limpio
y sin plomo. Siga las instrucciones en detalle para mezclar correctamente el
aceite y el combustible.
Befinicibn de los combustibles de mezcla
_ DVERTENClA: Se ha demostrado que el combustible que
contiene ma.sdel 15% de etanol probablemente ocasionara, dafios al
motor y anulara, la garantia.
Los combustibles actuales con frecuencia son una mezcla de gasolina y
oxigenantes como per ejemplo etanol, metanol o MTBE (eter). El combustible
mezclado con alcohol absorbe agua. Una cantidad tan pequefia como el 1% de
agua en el combustible puede causar la separaci6n del combustible y el aceite.
Forma acidos cuando esta almacenado. Cuando use combustible mezclado con
alcohol, use combustible nuevo (de menos de 30 dias).
Uso de combustibles de rnezcla
Si usted opta por usar un combustible de mezcla o si su uso es inevitable,
tome las precauciones recomendadas.
Use siempre una mezcla fresca de combustible segQn Io indica su
manual del operador.
Agite siempre la mezcla de combustible antes de cargarlo en la unidad.
Drene el tanque y haga funcionar el motor en seco antes de guardar la unidad.
Uso de aditivos en el combustible
PRECAUCION: Para que el motor funcione correctamente y
con la mayor fiabilidad, preste mucha atenci6n alas instrucciones de
mezcla de aceite y combustible del envase de aceite de 2 ciclos. El
uso de combustible mezclado en forma incorrecta puede dafiar
seriamente el motor.
La botella de aceite de 2 ciclos que vino con su unidad contiene un aditivo en el
combustible que ayudar& a inhibir la corrosi6n y a reducir la formaci6n de
dep6sitos de goma. Utilice siempre un buen 2 de aceite de ciclo disefiado para
motores refrigerados por aire, junto con un aditivo para el combustible, como el
STA-BIL ® estabilizador de gas o un equivalente. Agregue 23 mL (0,8 onzas) de
aditivo de combustible pot gal6n de combustible de acuerdo con las
instrucciones del envase. NUNCA agregue aditivos directamente en el tanque
de combustible de la unidad.
Mezcle bien la proporci6n correcta de aceite para motor de 2 ciclos y gasolina
sin plomo en una lata de combustible pot separado. Use una proporci6n de
40:1 de combustible y aceite. No los mezcle directamente en el tanque de
combustible de la unidad. Consulte las proporciones especificas de mezcla de
gasolina y aceite en la tabla siguiente.
NOTA: 3,8 litros (un gal6n) de
gasolina sin plomo
mezclada con una botella
de 95 mL (3,2 onzas) de
aceite de 2 ciclos es una
proporci6n de 40:1 de
combustible y aceite.
NOTA: Elimine la mezcla vieja de
aceite y combustible de
acuerdo con los
reglamentos federales,
estatales y locales.
GASOLINA SIN
PLOMO
ACEITE DE 2 ClCLOS
95 rnL
3,8 LITROS
(1 GALON de EE.UU.) (3,20NZAS
FLUIDAS)
1 LITRO 25 mL
PROPORCION DE LA MEZCLA = 40:1
17
CARGA DE COMBUSTIBLE EN LA UNIDAD
ADVERTENCIA: Saque la tapa del combustible lentamente
para evitar lesionarse con elrociado del combustible. No opere nunca
la unidad sin la tapa del combustible firmemente colocada en su lugar.
ADVERTENCIA: Cargue el combustible en un a.reaexterior
limpia y bien ventilada. Limpie de inmediato todo combustible que se
haya derramado. Evite crear una fuente de encendido con el
combustible derramado. No arranque el motor hasta que se hayan
evaporado los gases del combustible.
1. Saque la tapa de la gasolina.
2. Coloque el pico del recipiente de gasolina en el orificio de Ilenado del
tanque de gasolina y Ilene el tanque.
NOTA: No Ilene el tanque demasiado.
3. Limpie toda la gasolina que pueda haberse derramado
4. Vuelva a instalar la tapa de la gasolina.
5. Mueva la unidad por Io menos 9,1 m (30 pies) de la fuente y sitio de
carga antes de arrancar el motor.
NOTA: Elimine la gasolina vieja de acuerdo a los reglamentos federales,
estatales y locales.
NOTA: La unidad usa INCREDI-PULL TM Io cual reduce considerablemente el
esfuerzo requerido para arrancar el motor. Debe halar el cord6n de
arranque Io suficiente para oft que el motor trata de arrancar. No es
necesario halar el cord6n con energfa: no hay fuerte resistencia al halar.
Tenga en cuenta que este metodo de arranque es muy diferente (y
mucho mas facil) del que usted pudiera estar acostumbrado a usar.
Sl... El motor no arranca, regrese al paso 3.
NOTA: Si la unidad estA caliente y no Iogra arrancar despu6s de halar3 veces
el cord6n de arranque,
apriete el control del _ La Posici6n
obturador y hale el cord6n _" Equil3ado con _ que empieza
de arranque hasta que la INCI_I#_L_{H"
unidad arranque. Arranque de
INSTRUCCIONES DE APAGADO
1. Saque la mano del control del
regulador. Deje enfriar el
motor en marcha en vacio.
2. Coloque el control de
Control del
encendido y apagado en regulador
posici6n de APAGADO (O)
(Fig. 7). Fig. 10
ADVERTENClA: Use esta unidad s61o en un Area exterior
bien ventilada. Los gases de escape de mon6xido de carbono
pueden ser letales en un Area cerrada.
ADVERTENOIA: Evite los arranques accidentales. Col6quese
en posici6n de inicio cuando tire de la cuerda de arranque (Fig. 10). El
operador y la unidad deben estar en una posici6n estable al arrancar la
unidad para evitar graves lesiones personales.
INSTRUCCIONES DE ARRANQUE
1. Mezcle la gasolina con el
aceite. Vea las Instrucc/ones
para Mezclar el Aceite y el
Combustible.
2. Llene el tanque de
combustible con la mezcla
de combustible/aceite.
NOTA: No hay necesidad de girar
la unidad. Encendido!de
parada el control (Fig. 7)
esta en la posici6n de
trabajo siempre (I).
3. Oprima completamente el
cebador y sueltelo 10veces.
Hagalo lentamente. Sedebera
ver un poco de combustible en
el cebador yen lastuberias de
alimentaci6n de combustible
(Fig. 8).Si no puede ver el
combustible en el cebador,
oprfmalo y sueltelo tantas veces
come sea necesario hasta que
vea combustible en el mismo.
4. D6 la vuelta a la palanca del
cebador agujas del reloj hasta
que encaje (fig. 9).
5. AgAchese en la posici6n de
salida (Fig. 10). No exprima la
valvula reguladora. Titan de la
cuerda del arrancador con un
movimiento controlado hasta
que la unidad comience.
6. Espere y permita que la unidad
est6 desocupada por 5 - 10
segundos. Si la unidad deja de
funcionar durante este tiempo,
exprima la valvula reguladora y
tirar de la cuerda de arranque
en un movimiento controlado
hasta que la unidad comience.
7.
Apagado (O) _L.__
("_'_'_ Control del
regulador
Fig. 7
_ Bombilla
el cebador
Fig. 8
palanca del
cebador-_.
Fig. 9
Exprima y celebre el control de valvula reguladora para que los 30 a 60
segundos permitan que la unidad caliente.
COMO ARRANCA LA UNIDAD CON EL ARRANCADOR DE POTENCIA
ELECTRICO O EL ACCESORIO ARRANCADOR DE POTENCIA PARA
TALADRO
NOTA: iEsta unidad puede utilizar un accesorio opcional enchufable del
comienzo de la energia odel comienzo del pedacito de energia!
Refiera por favor al manual enchufable del operador del comienzo
de la energia odel comienzo del pedacito de energia para el uso
apropiado de esta caracteristica. (Se vende por separado) En la
pagina 21 de este manual encontrarA la informaci6n necesaria para
comprar estos accesorios).
INSTRUCCIONES DE ARRANQUE
1. Mezcle la gasolina con el aceite. Vea las Instrucciones para Mezclar el
Aceite y el Combustible.
2. Llene el tanque de combustible con la mezcla de combustible/aceite.
NOTA: No hay necesidad de girar la unidad. Encendido/de parada el control
(Fig. 7) esta en la posici6n de trabajo siempre ( I ).
3. Oprima completamente el cebador y sueltelo 10 veces. Hagalo lentamente.
Se debera ver un poco de combustible en el cebador y en las tuberias de
alimentaci6n de combustible (Fig. 8). Si no puede ver el combustible en el
cebador, oprfmalo y su61telo tantas veces come sea necesario hasta que
vea combustible en el mismo.
4. De la vuelta a la palanca del cebador agujas del reloj hasta que encaje (fig.9).
5. AgAchese en la posici6n de salida (Fig. 10). No exprima la vAIvula
reguladora. Coloque el arrancador de potencia electrico o el accesorio
arrancador de potencia para taladro en la parte posterior de la unidad.
Consulte la secci6n de Operacidn del arrancador de potencia electrico
o accesorio arrancador de potencia para taladro del operador manual.
6. Apriete y mantenga apretado el ENCENDIDO (I) bot6n del arrancador
de potencia electrico o el taladro equipado accesorio arrancador de
potencia para taladro en intervalos de no mAs de 4 segundos cada
hasta que la unidad arranque.
7. Espere y permita que la unidad est6 desocupada por 5 - 10 segundos.
Si la unidad deja de funcionar durante este tiempo, exprima la valvula
reguladora, entonces apriete y mantenga apretado el ENCENDIDO (I)
bot6n del arrancador de potencia electrico o el taladro equipado
accesorio arrancador de potencia para taladro en intervalos de no mAs
de 4 segundos cada hasta que la unidad arranque.
8. Quitar el arrancador de potencia electrico o el taladro de la unidad.
9. Exprima y celebre el control de valvula reguladora para que los 30 a 60
segundos permitan que la unidad caliente.
Sl... el motor no arranca, regrese al paso 3.
Sl... el motor no arranca despues de unos cuantos intentos, oprima del control
del regulador, a continuaci6n, apriete y mantenga apretado el bot6n de
ENCENDIDO (I)del arrancador de potencia electrico o taladro en
intervalos de no mAs de 4 segundos cada hasta que launidad arranque.
INSTRUCCIONES DE APAGADO
1. Saque la mano del control del regulador. Deje enfriar el motor en
marcha en vacio.
2. Coloque el control de encendido y apagado en posici6n de APAGADO
(O) (Fig. 7).
18
COMO SOSTENER EL RECORTADOR
_ ADVERTENClA: Siempre ojo del desgaste, el oir, |
|
protecci6n del pie y del cuerpo para reducir el riesgo de lesi6n al
J
funcionar esta unidad.
Antes de operar esta unidad,
parese en posici6n de operaci6n
(Fig. 11). Verifique Io siguiente:
El operador tiene protecci6n
ocular y ropa adecuada.
El brazo derecho esta levemente
doblado, y la mano esta
sosteniendo el mango del eje.
El brazo izquierdo esta recto y la
mano sostiene la manija en D.
La unidad estA debajo del nivel ,_
de la cintura. Fig. 11
El accesorio de corte esta
paralelo al suelo y hace facil contacto con la vegetaci6n que va a ser
cortada sin que el operador tenga que inclinarse.
AJUSTE DE LA LONGITUD DE LA MNEA DE CORTE
_ ADVERTENCIA: No saque ni altere el ensamble de la
cuchilla limitadora de linea. La linea Iongitud excesiva causarA
J
fallo mecAnico prematuro y / o dafio de la unidad.
El accesorio de corte Bump Head TM
le permite soltar linea de corte sin
apagar el motor. Para soltar mas
linea, golpee suavemente el
accesorio de corte contra el suelo
(Fig. 12) mientras opera el
recortador a alta velocidad.
NOTA: Mantenga siempre la linea
de corte completamente
extendida. Es mAs dificil
soltar linea al acortarse la .'_.
linea de corte.
Cada vez que se golpea la cabeza, Fig. 12
se suelta alrededor de 25,4 mm (1 pulgada) de linea de corte. La cuchilla en la
protecci6n del accesorio de corte detendrA la linea en la Iongitud correcta si
se suelta demasiada linea.
Para obtener mejores resultados, golpee la perilla percuisva sobre terreno
limpio o tierra dura. Si intenta soltar la linea sobre el c6sped alto, el motor
podrA ahogarse.
NOTA: No apoye la perilla percuisva sobre el suelo mientras la unidad est6
en funcionamiento.
La linea puede cortarse pot:
Enredarse con un objeto extrafio
Fatiga normal de la linea
Intentar cortar hierbas gruesas y lefiosas
Forzar la linea en objetos como paredes o postes de cercos.
CONSEJOS PARA OBTENER MEJORES RESULTADOS AL RECORTAR
El Angulo correcto para ubicar el accesorio de corte es paralelo al suelo.
No fuerce el accesorio de corte. Permita que la punta de la linea realice el
corte (en especial a Io largo de paredes). Si corta con mAs de la punta
reducira la eficacia del corte y puede sobrecargar el motor.
Corte c6sped de mas de 200 mm (8 pulgadas) trabajando de arriba hacia
abajo en pequefios incrementos para evitar el desgaste prematuro de la
linea y el arrastre del motor.
Corte de derecha a izquierda siempre que sea posible. Cortar hacia la
izquierda mejora la eficiencia de la unidad. Los recortes salen arrojados
en sentido contrario al operador.
Mueva lentamente el recortador dentro y fuera del Area de corte a la altura
deseada. Realice movimientos ya sea de adelante hacia atras y viceversa, o de
lado a lado. El corte en longitudes mas cortas produce mejores resultados.
Recorte Onicamente cuando el pasto y las hierbas est6n secas.
La vida de su linea de corte depende de:
Seguir todas las t6cnicas de corte indicadas anteriormente
El tipo de vegetaci6n que corte
El lugar donde se corta
Por ejemplo, la linea se desgastara mas rApido cuando corte contra un muro
que cuando corte alrededor de un Arbol.
RECORTE DECORATIVO
\
El recorte decorativo se realiza
eliminando toda la vegetaci6n de
alrededor de los Arboles, postes,
cercos, etc.
Gire toda la unidad a modo de
que el accesorio de corte se
ubique a un angulo de 30° con el
suelo (Fig 13). :30°
Fig. 13
19
PROGRAMA DE MANTENIMIENTO
_ DVERTENClA: Para evitar lesiones personales graves, nunca
realice manteni-miento ni reparaciones con la unidad funcionando.
Realice siempre el mantenimiento y las reparaciones con la unidad fria.
Desconecte el cable de la bujia de encendido para cerciorarse de que la
unidad no arrancar&
Estos procedimientos requeridos para el mantenimiento deben ser
realizados con la frecuencia indicada en la tabla. Deben ser incluidos como
parte de toda puesta a punto de cada temporada.
NOTA: Es posible que algunos procedimientos de mantenimiento
requieran herramientas o habilidades especiales. Si no esta
seguro sobre estos procedimientos, Ileve la unidad a Craftsman o
a otro proveedor de servicio calificado. Para mas informaci6n,
Ilame al 1-800-4-MY-HOME ®.
NOTA: El mantenimiento, el reemplazo o la reparaci6n de los dispositivos
y del sistema de control de emisiones puede ser realizado por
Craftsman o pot otra agencia de servicio calificada. Para mAs
informaci6n Ilame al 1=800=4=MY=HOME ®.
FRECUENCIA MANTENIMIENTO CONSULTE
REQUERIDO
Antes de arrancar Llene el tanque de combustible con la p. 17
el motor mezcla correcta de aceite y
combustible
Cada 10 horass Limpie y vuelva a aceitar el filtro p. 20
de aire
Cada 25 horass Inspeccione lacondici6n y la p. 21
separaci6n de la bujia de encendido
INSTALAOION DE LA MNEA
_ DVERTENOIA: No use nunca linea reforzada con metal,
alambre, cadena ni soga, etc. Estos elementos pueden
desprenderse y convertirse en un proyectil peligroso.
Esta secci6n cubre la instalaci6n de la linea SplitLine TM y de la linea individual
regular.
Use siempre la linea de repuesto de 2.41 mm (0.095 pulg). Una linea que no
sea la indicada puede causar que el motor se recaliente o falle.
Existen dos m6todos para cambiar la linea de corte.
Bobine el carrete interior con linea nueva.
Instale un carrete interior prebobinado
Bobinado del carrete interior existente
1. Sostenga la bobina exterior con una mano y desenrosque la perilla del
topet6n en sentido antihorario (Fig. 14). Inspeccione el perno de
adentro de la perilla
percusiva para verificar que Perilla del topet6n
se mueva con libertad.
Cambie la perilla percusiva si
esta dafiada. Perno
2. Saque el carrete interior de la
bobina exterior (Fig. 15).
3. Saque el resorte del carrete
interior (Fig. 15).
4. Use un paso limpio para limpiar
el carrete interior, el resorte, el
eje y la bobina exterior.
Fig. 14
5. Verifique el desgaste de los __ Bobina
dientes de posici6n del ____e.
carrete interior y bobina ___j_ _ exterior
exterior (Fig. 16). Si es
necesario, saque la rebaba o //
cambie la bobina.
el carrete y
NOTA: Use siempre la Iongitud _. "_-_:_j_//j
c orrecta de linea cuando cX_._._..______irrete
instale la linea de corte interior
en la unidad. La linea
puede no soitarse en _")_-
forma adecuada si es
demasiado larga. Fig. 15
Instalaci6n de la linea individual
Lea la instalaci6n de la linea Dientes de
SplitLine TM en el paso 8. posici6n
6. Tome aproximadamente 5.4 m
(18 pies) de nueva linea de
corte, enl&cela en dos
longitudes iguales. Inserte cada
extremo de la linea atrav6s de
uno de los dos orificios del
carrete interior (Fig. 17). Pase la
linea a traves del carrete interior _----_,'_
de modo que el lazo sea Io m&s
peque_o posible.
7. Bobine las lineas en capas
parejas y ajustadas sobre el
carrete (Fig. 18). Bobine la
linea en la direcci6n indicada
en el carrete interior. Coloque
su dedo indice entre las dos
lineas para evitar que se
superpongan. No
superponga los extremos de
la linea. Proceda al paso 12.
Instalaci6n de la Ifnea SplitMne TM
8. Tome aproximadamente 2.7 m
(9 pies) de nueva linea de
corte. Inserte un extremo de ia
linea a trav6s de uno de los
orificios del carrete interior
(Fig. 19). Pase la linea a trav6s
del carrete interior hasta que
queden s61o4 pulgadas fuera.
9. Inserte el extremo de la linea
en el orificio abierto del
carrete interior y tire de la
linea en forma ajustada a fin
de que el lazo sea Io mas
peque_o posible (Fig. 19).
10. Antes de bobinar, separe la
linea alrededor de 6 pulgadas.
11. Bobine la linea en capas
parejas y ajustadas en la
direcci6n indicada en el
carrete interior.
NOTA: Si no bobina la linea en
12.
13.
NOTA:
la direcci6n indicada, el
accesorio de corte no
funcionara en forma
correcta.
Inserte los extremos partidos
de la linea en las dos ranuras
de fijaci6n (Fig. 20).
Inserte los extremos partidos
de la linea a trav6s de los
ojalillos de la bobina exterior
y coloque el carrete interior
con el resorte dentro de la
bobina exterior (Fig. 21).
Empuje el carrete interior y la
bobina exterior entre si.
El resorte debe estar
ensamblado en el
carrete interior antes de
volver a ensamblar el
accesorio de corte.
Fig. 16
Lazo
Fig. 17
Fig. 18
Fig. 19
Lazo
Ranuras
de fijaci6n
14. Mientras sostiene el carrete
interior y la bobina exterior,
tome los extremos partidos y
tire con firmeza para soltar la
linea de las ranuras de
retenci6n de la bobina.
15. Sostenga el carrete interior
en su lugar e instale el bot6n
de tope girAndolo en sentido
horario. Ajuste bien.
INSTALACION DE UN CARRETE
PREBOBINADO
Ojalillos
Resorte ._ .
Fig. 21
_ DVERTENCIA: Para evitar graves lesiones personales, J
apague siempre su recortador y espere que se enfrie antes de
limpiarlo o realizar todo tipo de mantenimiento.
1. Sostenga la bobina exterior con una mano y desenrosque la perilla
percusiva en sentido antihorario (Fig. 14). Inspeccione el perno dentro
del bot6n de tope para verificar que se mueva con libertad. Cambie el
bot6n de tope siesta da_ado.
2. Saque el carrete interior viejo de la bobina exterior (Fig. 15).
3. Saque el resorte del carrete interior viejo (Fig. 15).
4. Coloque el resorte en el carrete interior nuevo.
NOTA: El resorte debe estar ensamblado en el carrete interior antes de
volver a instalar el accesorio de corte.
5. Inserte los extremos de la linea en los ojalillos de la bobina exterior (Fig. 21).
6. Coloque el nuevo carrete interior dentro de la bobina exterior. Empuje el
carrete interior y la bobina exterior entre si. Mientras sostiene el carrete
interior y la bobina exterior, tome los extremos y tire con firmeza para
soltar la linea de las ranuras de retenci6n de la bobina.
7. Sostenga el carrete interior en su lugar e instale el bot6n de tope
gir&ndolo en sentido horatio. Ajuste bien.
MANTENIMIENTO DEL FILTRO DE AIRE
LJmpieza del filtro de aire
Limpie y vuelva a aceitar el filtro
de mire cada 10 horas de
operaci6n. Es una de las partes
cuyo mantenimiento es
importante. No mantener
debidamente su filtro de mire
puede resultar en funcionamiento
inadecuado o puede causar daRo
permanente a su motor.
1. Abra la cubierta del filtro de
mirepresionando hacia dentro
la lengQeta de traba y sacando
la cubierta del filtro (Fig. 22).
2. Retire el filtro de mire(Fig. 22).
3. Lave elfiltro con agua y
detergente (Fig. 23). Enjuague
bien el filtro y dejelo secar.
4. Aplique suficiente aceite limpio
de motor SAE 30 para recubrir
ligeramente el filtro (Fig. 24).
5. Apriete el filtro para esparcir
y retirar el exceso de aceite
(Fig. 25).
6. Vuelva a colocar el filtro de
mireen la tapa del filtro de
mire (Fig. 22).
NOTA: Si opera la unidad sin el
filtro de mire, su garantia
sera ANULADA.
7. Cierre la tapa del filtro de mire
haci6ndola girar hacia la
izquierda y luego haciendo
presi6n sobre la lengQeta de
cierre hacia abajo hasta que
caiga en su lugar (Fig. 22).
Cubierta del
filtro de mire
Leng_eta de cierre
Filtro de mire
Fig. 22
<
Fig. 23
Fig. 24
Fig. 20
20
1 / 1

ACE 7275340 Owner's manual

Category
Grass trimmers
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document

in other languages