Chief PFC2000S Installation guide

Chief
Brand
Chief
Model
PFC2000S
Category
Flat panel floor stands
Type
Installation guide

This manual is also suitable for

INSTALLATION INSTRUCTIONS
Display Carts
MFC, PFC Series
Installation Instructions MFC, PFC Series
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® and ClickConnect™ are registered trademarks of
Milestone AV Technologies. All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components on the cart does not exceed 125 lbs
(56.70 kg) for the MFC, and 200 lbs (90.72 kg) for the PFC.
MFC, PFC Series Installation Instructions
3
MFC
PFC
DIMENSIONS
Installation Instructions MFC, PFC Series
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions MFC, PFC Series
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
3/16"
(Included)
A (1)
E (1)
F (1)
J (1)
L (4)
5/16-18 x 3/4"
M (4)
5/16-18 x 2-3/4"
N (4)
5/16-18 x 4-1/4"
P (4)
5/16"
D (4)
C (2)
K (1)
[left leg]
B (1)
[right leg]
3/16"
3/16"
G (1)
H (1)
PFC Head
MFC Head
Assembly
Assembly
[snap-on cover]
[end cap]
[center post]
[cross bracket]
[drill bit]
MFC, PFC Series Installation Instructions
6
ASSEMBLY
CAUTION: Attachment holes may be damaged if a power
drill is used to insert button head cap screws. Screws should
first be inserted and turned BY HAND with the hex key or with
a handheld screwdriver BEFORE using the hex head drill bit
(J) and power drill to complete the attachment.
Assembling Cart
1. Assemble two legs (A) and (B) to the cart cross bracket (F)
using two 5/16-18 x 4-1/4" button head cap screws (N)
through one end cap (C) per leg. (See Figure 1)
Figure 1
CAUTION: INNER COLUMN IS SHIPPED DISENGAGED
and may pinch hands! Hold both inner and outer posts
(columns) while removing from box.
IMPORTANT ! : Press cable tie tab to loosen and
remove cable tie from around knob post. (See Figure 2)
NOTE: Disengage knob on center post BEFORE attaching
base to the center post.
2. Lift up slightly on the inner column of center post and hold
firmly toward top of post. (See Figure 2)
3. Pull out knob on the center post and turn 90° in either
direction to disengage the locking mechanism. (See
Figure 2)
4. Raise the inner column and turn the knob 90° in either
direction to engage the knob and lock the column in place.
(See Figure 2)
Figure 2
NOTE: Insert and turn screws in order shown (1, 2, 3, 4) in
Figure 3.
Figure 3
5. Attach center post (E) to leg assembly using four
5/16-18 x 2-3/4" button head cap screws (M) and four 5/16"
washers (P). (See Figure 3) and (See Figure 4)
Figure 4
(Front view of cart)
(N) x 4
(C) x 2
(B)
(F)
(A)
inner column
Cable
Tie
(Bottom view of cart)
1
2
3
4
(Front view of cart)
(M) x 4
(P) x 4
(E)
Installation Instructions MFC, PFC Series
7
IMPORTANT ! : When attaching head assembly ensure
that the ClickConnect lock is at TOP of head assembly,
and bracket tabs slide into the stand assembly. (See
Figure 5)
1. Slide head assembly (G) or (H) into the stand assembly.
(See Figure 5)
2. Attach head assembly (G) or (H) to the cart assembly using
four 5/16-18 x 3/4" button head cap screws (L).
(See Figure 5)
Figure 5
Adjusting Cart Height
CAUTION: ALWAYS remove the display(s) BEFORE
adjusting the height of cart.
1. Firmly grasp head assembly. (See Figure 6)
IMPORTANT ! : To avoid pinching hands, hold head
assembly when adjusting cart height.
Figure 6
2. Adjust the cart to the desired height by slightly lifting the
head assembly, pulling out knob on the center post and
turning 90
o
in either direction to disengage the locking
mechanism. (See Figure 7)
3. Raise or lower the center post, then turn the knob 90
o
either
direction to engage the knob and lock the cart at desired
height. (See Figure 7)
Figure 7
IMPORTANT ! : Set the height of the cart so the display
does NOT rest on the lower part of the center post.
(See Figure 7) Always set the height so the knob is
engaged in a hole in the center post.
ClickConnect
lock at TOP of
head assembly
2
(L) x 4
(G) or (H)
1
Bracket Tabs
Cart
Assembly
.
Grasp head assembly
within shaded area.
[PFC Head
Assembly Shown]
Do NOT let
display rest
here
2
3
Inner
Column
MFC, PFC Series Installation Instructions
8
Attaching Display to Cart
WARNING: EXCEEDING MAXIMUM WEIGHT CAPACITY
MAY LEAD TO SERIOUS PERSONAL INJURY OR
DAMAGE TO EQUIPMENT! It is the installer’s responsibility
to ensure the total amount of weight placed on the cart does
not exceed 125 lbs (56.70 kg) for the MFC, and 200 lbs
(90.72 kg) for the PFC.
CAUTION: Before attaching display to cart set the brakes
on the back wheels by pressing down on the tab. (See
Figure 8)
Figure 8
4. Attach a PSBU or MSBU interface bracket to the display
following the instructions included with the bracket.
5. While supporting both sides of display, align four mounting
buttons on display or interface bracket with four mounting
holes in head assembly. (See Figure 9) and (See Figure 10)
Figure 9
WARNING:
DISPLAY MAY WEIGH IN EXCESS OF 40
LBS! Always use two people and proper lifting techniques
when installing or positioning display on cart.
6. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes. (See Figure 9) and
(See Figure 10)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
CART OR DISPLAY FALLING CAUSING SERIOUS
PERSONAL INJURY OR DAMAGE TO EQUIPMENT!
Ensure mounting buttons are completely engaged in
mounting holes.
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 10)
Figure 10
Press down to
set brakes
5
6
5
6
May remove
pin and nut and
move to lower holes
A padlock or bolt
may be placed
through latch holes
Installation Instructions MFC, PFC Series
9
Tilting Display
The display can be tilted up to 15
o
either backward or forward
from a straight upright position.
1. Turn knob counterclockwise on back of head assembly to
loosen the tilt. (See Figure 11)
Figure 11
2. Tilt display as desired, to a maximum of 15
o
either forward
or backward.
3. Turn knob clockwise to tighten display on head assembly.
(See Figure 11)
CAUTION: Tighten knob on back of head assembly to
prevent damage when moving the cart and display.
4. If leaving the display in a straight upright position, it is
recommended that a bolt (not provided) be placed through
the head assembly (See Figure 11) to lock the display into
the upright position.
Cable Management
1. Signal cables can be run down the front flap of the center
post and out the front of the post at any of the openings.
(See Figure 12)
2. The display power cord can be run through the top and
down through the post to exit out the back. (See Figure 12)
3. Any accessory power cords can be run through the front
and down through the post to exit out the back. (See
Figure 12)
4. Install the snap-on covers (D) to any opening that is not
being used. (See Figure 12)
5. To remove the snap-on covers, grip the sides of the cover
in the middle and pull off. They can also be removed by
inserting a flat-blade screwdriver into the bottom slot and
rotating the screwdriver.
Figure 12
lock displaylock display
1
3
4
(MFC Shown)
Place optional bolt
(not provided) here
to lock in an upright
position.
2
(Rear
view of
center post)
(Front view
of center post)
Exit for
power
cables
1
3
Exits for
signal cables
(D)
MFC, PFC Series Installation Instructions
10
Cart Use and Maintenance
CAUTION: This cart is intended for use only with the
products and maximum weights indicated (125 lbs [56.70 kg]
for the MFC, and 200 lbs [90.72 kg] for the PFC). Use with
other products or products heavier than the maximum
weights indicated may result in instability causing possible
injury.
WARNING: CART CAN TIP OVER RESULTING IN RISK
OF INJURY. Do not allow children under 16 to move cart.
Only adults should move this cart. Move cart slowly. Apply
moving force on narrow dimension. Never apply force at top -
always push near middle. Push, don’t pull.
Figure 13
1. Always place cart on level surface.
2. Always lock the wheels when the cart is not moving.
3. Check and tighten the hex nuts on the casters occasionally.
(See Figure ) These should be checked especially after use
on uneven ground.
Figure 14
Push cart near
middle
Do NOT push
cart near top
x 4
Installation Instructions MFC, PFC Series
11
Removing Display from Cart
1. Remove bolt or padlock from faceplate (if used).
(See Figure 15)
NOTE: The pin may have been used as a more permanent
locking device. If so, remove nut and pin and move
from the lower holes to the upper holes.
2. Pull back on flag on upper mounting hole and press pin
down into "Open" position. (See Figure 15)
WARNING: EACH DISPLAY MAY WEIGH IN EXCESS OF
40 LBS! Always use two people and proper lifting techniques
when installing or positioning display on stand.
3. Carefully lift display from cart.
4. Lift up on pin and place flag back against faceplate to return
it to "Closed" position. (See Figure 15)
Figure 15
2
1
Remove bolt
or padlock
if used
Pin in
"Open"
position -
Pin in
"Closed"
position -
4
move to
"Open"
position to
move to
"Closed"
position
remove
display
after display
is removed.
MFC, PFC Series Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8809-000038 RevG
2010 Milestone AV Technologies,
a Duchossois Group Company
www.chiefmfg.com
08/10
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
F +31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Chief PFC2000S Installation guide

Chief
Brand
Chief
Model
PFC2000S
Category
Flat panel floor stands
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents