Hotpoint WDD 960 A User manual

Brand: Hotpoint

Model: WDD 960 A

Category: Tumble dryers

Type: User manual



English, 1

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the Washer-dryer and

starting a wash cycle, 6-7

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 8

Table of wash cycles

Personalisation, 9

Setting the temperature

Setting the drying cycle

Functions

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Garments requiring special care

Load balancing system

Precautions and tips, 11

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water or electricity supply

Cleaning the Washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 13

Assistance, 14

WDL 520 P/G/A/K

Instructions for use

WASHER-DRYER

Installation

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the Washer-

dryer.

Electric and water connections

Connecting the water inlet hose

NOTE: the seal is

included with the fill

hose on UK produced

models. So 1 should

read.

1. Connect the single end

hose connection onto

cold water tap with ¾

bsp thread etc. (see

figure).

Before making the connection, allow the water to

run freely until it is perfectly clear.

2. Connect the double

end hose connection to

the washer dryer. Screw

connections onto both

of the inlet valves

located at the top right-

hand side at the rear of

the appliance making

sure the flexible pipe

section of the "Y" is not

kinked (see figure).

! Although the two pipes are now connected to the

rear of the appliance, the washer dryer will draw

cold water as is required for both wash

programmes and tumble drying as required.

Note: This appliance SHOULD NOT BE

CONNECTED TO A HOT WATER SUPPLY.

3. Make sure there are no kinks or bends in the hose.

! The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

! If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

! Ensure that the supply taps are allowing water

through. Old taps may seize in the closed position

and thus prevent water reaching the machine.

! Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the Washer-dryer to inform

the new owner as to its operation and features.

! Read these instructions carefully: they contain

vital information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the Washer-dryer.

2. Check whether the Washer-dryer has been

damaged during transport. If this is the case, do

not install it and contact your retailer.

3. Remove the 2

protective screws and

the rubber bush with

the respective spacer,

situated on the rear of

the appliance (see also

the installation leaflet).

NB:The plastic spacers

may fall down inside the

machine once the bolt

has been removed, and will not interfere with the

operation of the machine.

4. Do not remove external bar.

5. Seal the gaps using the plastic plugs provided.

6. Keep all the parts: you will need them again if

the Washer-dryer needs to be moved to another

location.

! Packaging materials are not children's toys.

Levelling

Your machine may make a considerable amount of

noise if the two front feet have not been adjusted

correctly.

1. Install the Washer-dryer on a flat sturdy floor,

without resting it up against walls, furniture

cabinets or other.

2. If the floor is not

perfectly level, com-

pensate for any

unevenness by

tightening or loosening

the adjustable front

feet (see figure); the

angle of inclination,

measured according to

the worktop, must not

exceed 2°.

_ the supply voltage is included within the values

indicated on the Technical details table

(see page 5);

_ the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fused

plug it can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED

OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is

lost, the plug must not be used until a replacement

is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of

the correct colour as indicated by the coloured

marking or the colour that is embossed in words on

the base of the plug. Replacements can be obtained

directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable

through partitions, units etc., please ensure that

either:

the plug is replaced by a fused 13 ampere re-

wearable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with

BS 5733) which is accessible without moving the

appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instructions for connecting cable to an alternative

plug:

Important: the wires in the mains lead are coloured

in accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

Connecting the drain hose

Connect the drain

hose, without bending

it, to a draining duct or

a wall drain situated

between 65 and 100 cm

from the floor;

The drain hose may be

connected to an under-

sink trap. Before

connecting the drain

hose from the machine

ensure that any blanks

or removable ends have

been taken off the

spigot.

If it is place over the

edge of a basin or sink

be sure the free end

of the hose should not

be underwater.

! We advise against the use of hose extensions; in

case of absolute need, the extension must have

the same diameter as the original hose and must

not exceed 150 cm in length.

Ensure that if the drain hose is pushed into a

standpipe, that the end does not go down more

than 15cms (6 inches). If the hose is pushed down

too far, this may cause the machine to self -

syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

_ the socket is earthed and in compliance with

the applicable law;

_ the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (see page 5);

As the colours of the wires in the lead may not

correspond with the coloured markings identifyng

the terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted

with a

13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please remove the

plug by cutting the mains cable as close as possible to

the plug body and dispose of it as described above.

! The Washer-dryer should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to

leave it exposed to rain and thunderstorms.

! When the Washer-dryer is installed, the mains

socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or

dangerously compressed.

! The power supply cable must only be replaced by

an authorised serviceman.

Warning! The company denies all liability if and

when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle 1.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Technical data

Model

WDL 520 P/G/A/K

Dimensions

width 59.5 cm

height 85 cm

depth 60 cm

Capacity

from 1 to 7 kg for the wash programme

from 1 to 5 kg for the drying programme

Electrical

connections

please refer to the technical data

plate fixed to the machine

Water

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 54 litres

Spin speed

up to 1200 rotations per minute

Energy rated

programmes

according to

regulation

EN 50229

Wash : programme 1; temperature

60°C; using a load of 7 kg;

Drying:

first drying cycle performed with

a 2 kg load, by selecting the dryness

level;

the second drying cycle is performed

with a 5 kg load, by selecting the

dryness level.

This appliance conforms to the

following EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2002/96/EC

- 2006/95/EC (Low Voltage)

Description of the Washer-dryer and

starting a wash cycle

Detergent dispenser drawer: used to dispense

detergents and washing additives (see Detergents

and laundry).

ON/OFF button: switches the Washer-dryer on

and off.

WASH CYCLE knob: programmes the wash cycles.

During the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to

select the available functions. The indicator light

corresponding to the selected function will remain lit.

TEMPERATURE knob: sets the temperature or the

cold wash cycle (see Personalisation).

DRYING knob: used to set the desired drying

programme (see Personalisation).

WASH CYCLE PROGRESS

indicator light

s: used

to monitor the progress of the wash cycle.

The illuminated indicator light shows which phase is

in progress.

DOOR LOCKED indicator light: indicates whether

the door may be opened or not (see next page).

START/PAUSE button with indicator light: starts

or temporarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash

orange, while the indicator light for the current

wash cycle phase will remain lit in a fixed manner. If

the DOOR LOCKED

indicator light is switched

off, the door may be opened.

To start the wash cycle from the point at which it

was interrupted, press this button again.

TEMPERATURE

knob

Detergent dispenser drawer

WASH CYCLE PROGRESS

indicator lights

FUNCTION

buttons with

indicator lights

ON/OFF

button

DRYING

knob

DOOR

LOCKED

indicator light

START/PAUSE

button with

indicator light

Control panel

WASH CYCLE

knob

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has

begun, the indicator lights switch on one by one to

indicate which phase of the cycle is currently in progress.

Note: during the "Drain" phase, the indicator light

corresponding to the "Spin" cycle phase will illuminate.

Function buttons and corresponding

indicator lights

When a function is selected, the corresponding

indicator light will illuminate.

If the selected function is not compatible with the

programmed wash cycle, the corresponding indicator

light will flash and the function will not be activated.

If a function which is incompatible with another

function selected previously, only the most recent

selection will remain active.

 Door locked indicator light

If this indicator light is on, the appliance door is locked

to prevent it from being opened accidentally; to avoid

any damage, wait for the indicator light to switch off

before you open the appliance door.

! If the START/PAUSE indicator light (orange)

flashes rapidly at the same time as the function

indicator light, this indicates a problem has

occurred (see Troubleshooting).

Starting a wash cycle

1. Switch the Washer-dryer on by pressing the ON/OFF button. All indicator lights will switch on for a few

seconds, then they will switch off and the START/PAUSE indicator light will pulse.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see Personalisation).

5. Set the drying cycle if necessary (see Personalisation).

6. Measure out the detergent and washing additives (see Detergents and laundry).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain

lit in a fixed manner, in green.

To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9. At the end of the wash cycle the

indicator light will switch on. The DOOR LOCKED indicator light will

switch off, indicating that the door may be opened. Take out your laundry and leave the appliance door ajar to

make sure the drum dries completely.

Switch the Washer-dryer off by pressing the ON/OFF button.

Wash

Rinse

Spin

Dry

End of wash cycle

Note: as soon as a drying

level or time period has

been set, this indicator

light illuminates to indicate

that the selected wash

cycle will be followed by a

drying phase.

Wash cycles

Table of wash cycles

Description of the wash cycle

Max

temp.

(°C)

Max.

speed

(rpm)

Drying

Detergents

Max. load

(kg)

Cycle

duration

Wa sh

Fabric

softener

Normal

Mini

load

Normal

Mini

load

Essentials cycles

Cotton:

extremely soiled whites.

90° 1200

ll l

7 3 155 111

Cotton (1):

extremely soiled whites.

60° 1200

ll l

7314498

Cotton:

heavily soiled whites and resistant colours.

60° 1200

ll l

7312298

Cotton (2):

heavily soiled whites and delicate colours.

40° 1200

ll l

7 3 115 91

Coloured Cottons (3):

lightly soiled whites and delicate colours.

40° 1200

ll l

738571

Synthetics:

heavily soiled resistant colours.

50° 800

ll l

31,58263

Fastwash 60':

to refresh lightly soiled garments quickly

(not suitable for wool, silk and clothes which require washing by hand).

60° 1200

ll l

3 - 60 -

Specials cycles

Baby cycle:

heavily soiled delicate colours.

40° 800

ll l

2 1 118 97

Shirts

40° 600

ll l

2 1 69 65

Ready to wear (*)

30° 800

ll l

60 -

Wo o l :

for wool, cashmere, etc.

40° 800

ll l

1,5 1 55 51

Silk/Curtains:

for garments in silk and viscose, lingerie.

30° 0

2 1 55 51

Drying cycles

Drying Cottons

- -

- - -

Drying Synthetics

- -

- - -

Drying Wool

- -

1,5

- - -

Partials wash cycles

Rinse Fast - 1200

7 3 36 32

Spin Fast - 1200

- -

7 - 16 -

Pump out - 0

- - -

7 - 2-

The information contained in the table is intended as a guide only.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 1 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.

(*) Ready to Wear

This cycle was designed to wash and dry lightly soiled small loads quickly. By selecting this cycle it is possible to

wash and dry a maximum load of 1 kg in just 60 minutes.

Please note, this is an automatically programmed wash and dry cycle, therefore it is not possible to manually

set a drying time or drying level in conjunction with this cycle.

Please note, the Drying indicator illuminates only during the drying phase of the cycle, not when the cycle is

first selected.

Personalisation

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash (

The Washer-dryer will automatically prevent you from selecting a temperature which is higher than the

maximum value set for each wash cycle.

Setting the drying cycle

Turn the DRYING knob to set the desired drying type.

Two options are available:

A - Based on time: from 40 to 180 minutes.

B - Based on the how damp the clothes are once they have

been dried:

Iron

: slightly damp clothes, easy to iron.

Hanger

: dry clothes to put away.

Cupboard

: very dry clothes, recommended for towelling

and bathrobes.

If your laundry load to be washed and dried is much greater than the maximum stated load (see adjacent

table), perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some

of them back in the drum. At this point, follow the instructions provided for a "Drying only" cycle. Repeat this

procedure for the remainder of the load.

N.B: when the drying is complete there is a cooling period, even though the DRYING knob is in the

position.

Drying only

Turn the WASH CYCLE knob to one of the drying settings (11-12-13) according to the type of fabric, then

select the desired drying duration using the DRYING knob.

Functions

The various wash functions available with this Washer-dryer will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in

conjunction with the selected wash cycle.

Slow Spin (1200-600)

By selecting this function, reduces the spin speed.

 This function may not be used in conjunction with wash cycles 8, 10, 11, 12, 13, C.

Mini load

This function is recommended for when the load of laundry is equal to half, or less than half, of the maximum

recommended load (see Table of wash cycles).

 This function may not be used in conjunction with wash cycles 5, 8, 11, 12, 13, B, C.

Extra rinse

By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is

guaranteed. It is particularly useful for sensitive skin.

 This function may not be used in conjunction with wash cycles 8, 11, 12, 13, B, C.

Super Wash

Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased

cycle duration, this function offers a high-performance wash.

 This function may not be used in conjunction with wash cycles 5, 8, 9, 10, 11, 12, 13, A, B, C.

Fabric

type

Load type Max.

load

(kg)

Cupboard

dry

Henger

dry

Iron

dry

Cotton Clothing of different

sizes, Terry towels

5180170160

Synthe-

tics

Sheets, Shirts, Pyjamas,

socks, etc.

3180170160

Wool Knitwear, Pullovers, etc.

1,5 150 140 130

Table of Drying times (guideline values)



Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct

dose of detergent: adding too much detergent will

not necessarily result in a more efficient wash, and

may in fact a build up on the inside of your appliance

and contribute to environmental pollution.

! Do not use hand washing detergents because

these create too much foam.

Open the detergent

dispenser drawer and

pour in the detergent or

washing additive, as

follows.

! Do not pour detergent into the middle compartment (*).

Detergent should only be poured into the compartment 1.

compartment 1: Detergent for the wash

cycle (powder or liquid)

For best results liquid detergent should be poured

in the dispenser immediately before the start of

the programme.

compartment 2: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Preparing the laundry

 Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from

whites.

 Empty all garment pockets and check the buttons.

 Do not exceed the listed values, which refer to

the weight of the laundry when dry:

Durable fabrics: max. 7 kg

Synthetic fabrics: max. 3 kg

Delicate fabrics: max. 2 kg

Wool: max. 1,5 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Baby cycle: this wash cycle 6 can be used to

remove the soiling typically caused by babies, while

ensuring that all detergent is removed from

nappies in order to prevent the delicate skin of

babies from suffering allergies. The cycle has been

designed to reduce the amount of bacteria by using

a greater quantity of water and optimising the

effect of special disinfecting additives added to the

detergent.

At the end of the wash cycle, the machine will slowly

rotate the drum to prevent the formation of

creases; to end the cycle press the START/PAUSE

button.

Shirts: use special wash cycle 7 to wash shirts in

various fabrics and colours.

It guarantees maximum care is taken of the

garments and minimises the formation of creases.

Wool: Hotpoint is the only Washer-dryer

manufacturer to have been awarded the

prestigious Woolmark Platinum Care endorsement

(M.0508) by the Woolmark Company, which means

that all woollen garments may be washed in the

Washer-dryer, even those which state hand wash

only

on the label. Wash cycle 9 therefore offers

complete peace of mind when washing woollen

garments in the Washer-dryer (max. load 1,5 kg) and

guarantees optimal performance.

Silk: use special wash cycle 10 to wash all silk

garments. We recommend the use of special detergent

which has been designed to wash delicate clothes.

Curtains: fold curtains and place them in a pillow

case or mesh bag. Use wash cycle 10.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

and to distribute the load in a uniform manner, the

drum rotates continuously at a speed which is slightly

greater than the washing rotation speed. If, after

several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the load

is excessively unbalanced, the Washer-dryer per-

forms the distribution process instead of spinning.

To encourage improved load distribution and balance,

we recommend small and large garments are mixed

in the load.

Anti-crease

This function interrupts the wash programme, and

the washing is left to soak in water before the

appliance is drained. It can only be used with

programme 10 (Silk/Curtains) and helps to prevent

the formation of creases.

To complete the cycle press the START/PAUSE

button.



Precautions and tips

! This Washer-dryer was designed and constructed

in accordance with international safety regulations.

The following information is provided for safety

reasons and must therefore be read carefully.

General safety

 This appliance was designed for domestic use only.

 The Washer-dryer must only be used by adults, in

accordance with the instructions provided in this manual.

 Do not touch the machine when barefoot or with

wet or damp hands or feet.

 Do not pull on the power supply cable when

unplugging the appliance from the electricity

socket. Hold the plug and pull.

 Do not open the detergent dispenser drawer

while the machine is in operation.

 Do not touch the drained water as it may reach

extremely high temperatures.

 Never force the porthole door. This could damage

the safety lock mechanism designed to prevent

accidental opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms

in an attempt to repair it yourself.

 Always keep children well away from the appliance

while it is operating.

 The door can become quite hot during the wash cycle.

 If the appliance has to be moved, work in a group

of two or three people and handle it with the

utmost care. Never try to do this alone, because

the appliance is very heavy.

 Before loading laundry into the Washer-dryer,

make sure the drum is empty.

 During the drying phase, the door tends to get

quite hot.

 Do not use the appliance to dry clothes that have

been washed with flammable solvents (e.g.

trichlorethylene).

 Do not use the appliance to dry foam rubber or

similar elastomers.

 Make sure that the water tap is turned on during

the drying cycles.

Disposal

 Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires

that old household electrical appliances must not

be disposed of in the normal unsorted municipal

waste stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Opening the porthole door manually

In the event that it is not possible to open the

porthole door due to a powercut, and if you wish to

remove the laundry, proceed as follows:

1. remove the plug from

the electrical socket.

2. make sure the water

level inside the machine is

lower than the door

opening; if it is not,

remove excess water

using the drain hose,

collecting it in a bucket as

indicated in the figure.

3. using a screwdriver,

remove the cover panel on

the lower front part of

the washing machine (see

figure).

4. pull outwards using the tab as indicated in the

figure, until the plastic tie-rod is freed from its

stop position; pull downwards and open the door at

the same time.

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.



Care and maintenance

Cutting off the water and

electricity supplies

 Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system inside

the Washer-dryer and help to prevent leaks.

 Unplug the Washer-dryer when cleaning it and

during all maintenance work.

Cleaning the Washer-dryer

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth soaked

in lukewarm soapy water. Do not use solvents or

abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pulling

it out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of

your appliance

 Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Cleaning the pump

The Washer-dryer is fitted with a self-cleaning

pump which does not require any maintenance.

Sometimes, small items (such as coins or

buttons) may fall into the pre-chamber which

protects the pump, situated in its bottom part.

! Make sure the wash cycle has finished and

unplug the appliance.

!

Troubleshooting

Your Washer-dryer could fail to work. Before contacting the Technical Assistance Centre

(see Assistance), make sure that the problem cannot be not solved easily using the following list.

Problem:

The Washer-dryer does not

switch on.

The wash cycle does not start.

The Washer-dryer does not

take in water (the indicator

light for the first wash cycle

stage flashes rapidly).

The Washer-dryer continuously

takes in and drains water.

The Washer-dryer does not

drain or spin.

The Washer-dryer vibrates a

lot during the spin cycle.

The Washer-dryer leaks.

The START/PAUSE indicator light

(orange) and the function

indicator lights flash rapidly.

There is too much foam.

The washer-dryer does not dry.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or is not making contact.

 There is no power in the house.

 The Washer-dryer door is not closed properly.

 The ON/OFF button has not been pressed.

 The START/PAUSE button has not been pressed.

 The water tap has not been opened.

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START/PAUSE button has not been pressed.

 The drain hose is not fitted at a height between 65 and 100 cm from the

floor (see Installation).

 The free end of the hose is under water (see Installation).

 The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and contact the Assistance Service. If the

dwelling is on one of the upper floors of a building, there may be problems

relating to water drainage, causing the Washer-dryer to fill with water

and drain continuously. Special anti-draining valves are available in shops

and help to avoid this inconvenience.

 The wash cycle does not include draining: some wash cycles require the

drain phase to be started manually.

 The ANTI CREASE function has been activated: To complete the wash

cycle, press the START/PAUSE button (Personalisation).

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).

 The Washer-dryer is not level (see Installation).

 The Washer-dryer is trapped between cabinets and walls (see Installation).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser drawer is blocked (for cleaning instructions, see

Care and maintenance).

 The drain hose is not fixed properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute

and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

 The detergent is not suitable for machine washing (it should display the

text for Washer or hand and machine wash, or the like).

 Too much detergent was used.

 The appliance is not plugged into the socket, or not enough to make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 The DRYING knob is on the

setting.

"

Assistance

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturers guarantee, which covers the cost of

breakdown repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective

because of either workmanship or materials, we will, at our discretion, either repair or replace the

appliance at no cost to you.

This guarantee is subject to the following conditions:

- The appliance has been installed and operated correctly and in accordance with our

operating and maintenance instructions.

- The appliance is used only on the electricity or gas supply printed on the rating plate.

- The appliance has been used for normal domestic purposes only.

- The appliance has not been altered, serviced, maintained, dismantled, or otherwise

interfered with by any person not authorised by us.

- Any repair work must be undertaken by us or our appointed agent.

- Any parts removed during repair work or any appliance that is replaced become our property.

- The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

- Damage resulting from transportation, improper use, neglect or interference or as a result

of improper installation.

- Replacement of any consumable item or accessory . These include but are not limited to: plugs,

cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.

- Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL

OR NON-DOMESTIC PREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on

you registering your appliance with us and the parts being fitted by one of our authorised engineers.

There will be a charge for our engineer's time. To activate the extra parts warranty on your

appliance, simply call our registration line on 0870 6092094 (ROI 01 230 0800).

Extended Guarantees

We offer a selection of repair protection plans that enable you to fully cover yourself against the expense

of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on

08709 088 088 (ROI 01 230 0233).

Free Helpdesk Service

We have a dedicated team who can provide free advice and assistance with your appliance if you

experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint

Service Hotline on 08709 066 066 (ROI 0818 313 413) for telephone assistance, or, where

necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will

replace your machine or, if you prefer, give you your money back.

#

After Sales Service

No one is better placed to care for your Hotpoint appliance during the course of its

working life than us - the manufacturer.

Essential Contact Information

Hotpoint Service

We are the largest service team in Europe offering you access to 400 skilled telephone advisors and

1100 fully qualified engineers on call to ensure you receive fast, reliable, local service.

UK: 08709 066 066

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following information:

Model number:

Serial number:

Parts and Accessories

We supply a full range of genuine replacement parts as well as accessory products that protect and

hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.

UK: 08709 077 077

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts

guarantee you must register your appliance with us.

UK: 0870 6092094

Republic of Ireland: 01 230 0800

www.hotpointservice.co.uk

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB

Indesit Company Unit 49 Airways Industrial Estate,Dublin 17

Recycling & Disposal Information

As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right

to use quality, recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,

remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts

separately to ensure that the appliance can no longer be plugged into a mains socket, and the door

cannot be locked shut.

$

WDL 520 - 195070003.03

02/2009 - Xerox Fabriano

Hotpoint WDD 960 A User manual

Brand: Hotpoint

Model: WDD 960 A

Category: Tumble dryers

Type: User manual

Download PDF

report

Hotpoint WDD 960 A User manual

Hotpoint WDD 960 A User manual

Related papers