Martin StageHazer is a professional haze machine designed to produce a translucent environment for intelligent lighting effects. It features:
- Precise temperature control and a high-mass heater block for optimal particle size and dispersion
- Unique dispersal chamber for efficient mixing and projection of haze
- Variable output remote control for precise haze level adjustment
-
Martin StageHazer is a professional haze machine designed to produce a translucent environment for intelligent lighting effects. It features:
- Precise temperature control and a high-mass heater block for optimal particle size and dispersion
- Unique dispersal chamber for efficient mixing and projection of haze
- Variable output remote control for precise haze level adjustment
-
MANUFACTURED BY
MARTIN MANUFACTURING (UK) PLC
BELVOIR WAY,
FAIRFIELD INDUSTRIAL ESTATE,
LOUTH, LINCOLNSHIRE. LN11 0LQ.
TEL:(01507) 604399 FAX:(01507) 601956
JEM
USER GUIDE
VERSION 1.3
STAGE-HAZER
DMX
STAGE-HAZER DMX
MARTIN MANUFACTURING (UK) PLC
MARTIN MANUFACTURING (UK) PLC
Pro-Haze
Fluids Suitable For This Machine:
Note:
The JEM warranty will be void if any fluid other then JEM approved fluid is used. If
other fluids are used there could be serious damage to the machine and the fluid
may not have been tested for use in public areas.
STAGE-HAZER USER GUIDE
How To Contact Us
Address:
Telephone:
Fax:
Email: [email protected]
Website: Http://www.jemsmoke.com
/
MARTIN MANUFACTURING (UK) PLC
Martin Manufacturing (uk) Plc
Belvoir Way,
Fairfield Industrial Estate,
Louth, Lincolnshire. LN11 0LQ.
+44 (0) 1507 604399
+44 (0) 1507 601956
STAGE-HAZER USER GUIDE
STAGE-HAZER USER GUIDE
Notes
PAGE 12
MARTIN MANUFACTURING (UK) PLC
User Guide Index
•
•
•
•
•
•
•
•
Introduction
Safety
Machine Layout
Getting Started
Using The Remote Control
Using DMX 512
Trouble Shooting
How To Contact Us
PAGE 1
MARTIN MANUFACTURING (UK) PLC
Note:
Martin Manufacturing (UK) reserves the right to modify or change the
specification of this product without prior notice.
No part of this publication shall be copied without permission
© Martin Manufacturing (UK). 1999
STAGE-HAZER USER GUIDE
STAGE-HAZER USER GUIDE
Introduction
The is a brand new machine from JEM which has been
designed to produce a perfect translucent environment for today’s intelligent
lighting effects.
Furthermore, this unique design is guaranteed to give the user maximum
reliability thanks to features such as the “Low fluid cut off system”,which
protects the pump in the event of running the machine dry.
Creating the perfect ambient haze relies heavily on the correct particle size
and dispersion. The STAGE-HAZER produces this by vapourising the special
working fluid at very precise temperature in a high mass heater block which
contains a cuperous helicoil of 3 metres length.
The product of this process is injected into the uniquely designed JEM
“Dispersal Chamber” where it is mixed with a turbulent airflow and projected
from the machine as an optically translucent haze at 1200 ft / minute (exit
velocity).
JEM has also used the “DTP” safety device, as used on the ZR12, ZR22 and
Techno-Fog to ensure the best possible overheat protection.
DMX 512
“DTP” Safety system
SMD electronics
Low fluid cut off system
Variable output remote
9.5 Litre fluid capacity
Dispersal chamber
2 x High power Fan
STAGE-HAZER
Features:
•
•
•
•
•
•
•
•
PAGE 2
MARTIN MANUFACTURING (UK) PLC
PAGE 11
MARTIN MANUFACTURING (UK) PLC
STAGE-HAZER USER GUIDE
Notes
PAGE 10
Trouble Shooting
CAUSE CURE
SYMPTOM
The mains switch does not light
when I switch on.
Main fuse blown..
No power connected.
Check main fuse.
Check power is connected.
The power LED does not light on
the remote control.
Fuse on main PCB blown.
Remote control not connected.
Check fuse on Main PCB.
Check connection of remote control.
The ready LED does not light.
even after 15 minutes.
Thermocouple fault
Thermal trip fault
Contact your Distributor.
No haze output. Low fluid level.
No fluid in container.
Check fluid level LED.
Replenish fluid container.
MARTIN MANUFACTURING (UK) PLC
STAGE-HAZER USER GUIDE
STAGE-HAZER USER GUIDE
Safety
•
•
•
•
•
•
•
Always use a JEM approved fluid, other fluids could be dangerous and could
cause damage to the machine.
Always check the voltage is correct for use with the machine, the voltage
setting is printed on the serial label.
Always read the user guide before operating the machine, smoke machines
need to be operated carefully to avoid risk.
Do not remove the cover or attempt to repair a faulty machine, an authorized
JEM dealer should be contacted in the event of a faulty machine.
Always use smoke machines in well ventilated areas, over use could affect
sufferers of asthma or other chest conditions.
Do not use the machine if there is a faulty mains lead or plug this could be
dangerous.
Do not spill fluid over the machine, if fluid is spilt clean with clean water and
contact an approved JEM dealer for advice.
Mains Lead Wiring Instructions
Brown = Live
Blue = Neutral
Green/Yelllow = Earth
Note! This Appliance must be earthed
PAGE 3
MARTIN MANUFACTURING (UK) PLC
STAGE-HAZER USER GUIDE
Machine Layout
PAGE 4
MARTIN MANUFACTURING (UK) PLC
FLUID OUT
LED
READY LED
HEAT LED
FLUID
COMPARTMENT
DMX IN
REMOTE
DMX OUT
TOP VIEW
TWIN FANS
MAINS SWITCH
POWER LEAD
REAR VIEW
DMX Connections
PAGE 9
MARTIN MANUFACTURING (UK) PLC
1
2
3
1
2
3
DMX IN
DMX OUT
STAGE-HAZER USER GUIDE
PIN
FUNCTION
1
2
3
Ground
DMX Data -ve
DMX Data +ve
Using DMX 512
DMX 512 is an industry standard and the is fitted with an
interface as standard. This gives the user the option of linking the smoke machines into
the lighting chain and controlling them from a single source. The STAGE-HAZER uses
a single channel to fire and control the output level, the interface can be addressed
from channel 1 up to channel 512. The address is set using the 10 way dip switch at the
rear of the machine. To address the channel, convert the channel number to binary and
set this number on the switches (on is down). There are some samples of different
channel settings below.
The is fitted with two XLR sockets for DMX, one is for DMX IN &
one is for DMX OUT; this enables the to be used in a chain. When
there is valid DMX, i.e. the XLR is connected and the desk is powered, the small green
LED will light indicating there is DMX connected to the machine. However, if there is
no address set, the LED will not light and DMX will be disabled. If an address is set
and DMX is present the machine will automatically start to heat up and after approxi-
mately 8 minutes you will be able to operate the machine using DMX. Increasing the
DMX level will increase the smoke output level.
STAGE-HAZER
STAGE-HAZER
STAGE-HAZER
12345678910
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
ON
ON
ON
Valid DMX LED
Address Switches
512
512
256
256
128
128
64
64
32
32
16
16
8
8
4
4
2
2
1
1
DMX Value
Switches 3,7, &9 on
Address set to 324
Switches1&5on
Address set to 17
PAGE 8
MARTIN MANUFACTURING (UK) PLC
STAGE-HAZER USER GUIDE
PAGE 5
STAGE-HAZER USER GUIDE
Getting Started
•
•
•
Once you have selected the best position for the STAGE-HAZER you can
begin to use the machine. First check the power supply you have is correct
for the machine .If it is, you can connect to the power supply and switch the
mains switch on at the rear of the machine; the machine will start to heat up
and the fan will run. It will take approximately 8 minutes for the machine to
reach working temperature. While it heats up you should check the level in
the fluid container; the container can hold up to 9.5 litres of fluid. The
machine may not heat if there is inadequate fluid in the container (the red
‘fluid out’ LED must not be on).
When you have finished using the machine you should turn the mains switch
off. If any problems occur when operating the STAGE-HAZER please refer to
the trouble shooting guide.
When the machine has reached working temperature the green “ready” LED
will light on the top of the machine and the machine can now be operated.
Press the prime button until haze appears from the output; the pump is now
primed. This will only have to be done if the fluid lines have become empty.
The output can now be set to the desired level by turning the “output” knob.
MARTIN MANUFACTURING (UK) PLC
PAGE 6
Using The Remote Control
The Technohaze comes with a compact remote allowing the user to prime the pump
and control the output level.
MARTIN MANUFACTURING (UK) PLC
1
2
3
4
5
6
7
8
9
OUTPUT
PRIME
ON
OUTPUT CONTROL
POWER
LED
PRIME
BUTTON
STAGE-HAZER USER GUIDE
PAGE 7
MARTIN MANUFACTURING (UK) PLC
Remote Control Functions
•
•
OUTPUT LEVEL CONTROL:
Use the control to
give the output density you require.
Setting the level control to minimum will switch off the output
POWER LED: This indicates that the machine is powered and that the
remote is connected.
When starting the machine for the first time,
use the prime button as described on page 5 para 2. During normal opera-
tion, the output control should be set between 4 and 10.
STAGE-HAZER USER GUIDE
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Martin StageHazer is a professional haze machine designed to produce a translucent environment for intelligent lighting effects. It features:
- Precise temperature control and a high-mass heater block for optimal particle size and dispersion
- Unique dispersal chamber for efficient mixing and projection of haze
- Variable output remote control for precise haze level adjustment
-
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Martin TechnoHaze User manual
-
Martin JEM K1 Hazer User manual
-
-
Martin Jem ZR12 DMX User manual
-
-
Martin Magnum 550 User manual
-
-
Martin JEM Ready 365 User manual
-
-
Other documents
-
Chauvet Arena Hazer 3 User manual
-
Stairville HZ-1500 Pro Touring Hazer DMX User manual
-
Robe Haze 400 FT User manual
-
JEM Compact Hazer Pro Owner's manual
-
thomann Hz-200 Compact Hazer DMX User manual
-
Stairville Hz-200 Compact Hazer DMX Owner's manual
-
Rockville ROCKHAZE 1000 V2 Owner's manual
-
-
-