Your SCM 960 microphone was carefully packed at the factory, and the shipping carton (or carrying case) was designed to
protect the unit during shipping. Please retain this container for subsequent transport and in the highly unlikely event that you
ever need to return your microphone for servicing. The optional SMCC-2 aluminum carrying case is highly recommended for the
most convenient and safe transport or permanent storage. It has roomy compartments for your SCM 960 microphone and all
available accessories, plus XLR cables.
Congratulations on purchasing a Nady SCM 960 Condenser Microphone. These superior microphone is perfect for
recording studio vocals, acoustic instruments, orchestras and choral groups, ambient instrument audio, and many
live sound applications. Powerful and versatile, the SCM 960 microphone meets the stringent requirements of even
the most demanding digital recording and live broadcasting applications.
UNPACKING, INSPECTION, STORAGE AND TRANSPORT
SCM 960 microphone
User guide
Warranty card
48V phantom power supply (SMPS-1)
Aluminum flight case (SMCC-2)
Shockmount (SSM-3)
Foam windscreen (FW-1)
The SCM 960 offers transformerless output and true condenser design (element constantly biased by the pre-amp) for exception-
ally low self noise and increased dynamic range, enhanced low and high end response with improved linearity across the
frequency range and maximum SPL capacity. It features a large diaphragm capsule (1 inch), three-way pad switch with 0dB,
10dB and 20dB of attenuation, and two selectable polar patterns: omni and cardioid. The SCM 960 uses a carefully selected
Field Effect Transistor (FET), specially chosen for its low distortion and superior signal-to-noise ratio.
(Note: For optimum performance, it is best to let the microphone warm up for 5 to 10 minutes)
The SCM 960 is manufactured with the finest materials and features a machined housing with advanced internal shock mount
construction for the highest structural integrity and rugged reliability. It requires 48V phantom power to operate, typically
supplied by the microphone pre-amplifier or mixing console. The optional Nady SMPS-1 phantom power supply can also be
used.
STANDARD ITEMS SUPPLIED
OPTIONAL ACCESSORIES
FEATURES
This guide covers the operation of the SCM 960 microphone and the available optional accessories.
To take full advantage of the superb features of your microphone, and to enjoy long and trouble-free use, please
read this user's guide carefully.
NADY SCM 960
USER GUIDE
Your SCM 960 microphone can be used with the optional Nady SSM-3 spider shock mount (or equivalent), which uses an
elastic suspension to isolate the microphone from vibration, thereby lowering noise transmitted to the microphone from the stand.
This is a useful tool in many situations, such as when the performer is tapping his or her feet, or when there is noise pickup from
the rumbling of traffic outside of the building. The disadvantage of using the shock mount is that the weight of the microphone
may make it drift in the elastic suspension, so mic placement may take a little longer.
To insert your SCM 960 microphone into the SSM-3 shock mount, pinch close the levers on the sides of the mount to the open
position, then slide the microphone into place.
The capsule is the heart of your condenser microphone. If it become dirty or wet , the sound will be degraded. Never spray any
liquid on the microphone head. Always use a foam windscreen if you talk or sing close to the microphone grill screen.
The FW-1 optional foam windscreen can also be used with your SCM 960. This windscreen fits over the grill portion of the
microphone and is designed primarily to decrease bass rumble (from wind noise pickup during outdoor live or recording use. It
is also useful in keeping mouth spray out of the microphone head. The FW-1 or some other windscreen should be used when-
ever someone is close miked to both protect the microphone and to also eliminate "popping" from percussive breath sounds.
(Note: Be aware that the foam windscreen will slightly attenuate the high frequency response of the microphone.)
The SCM 960 can be used in live sound reinforcement and broadcasting and in studio or live recording. It must be powered by
48V phantom power (such as supplied by the optional Nady SMPS-1 phantom power supply or a mixing console with phantom
powering), and amplified by a microphone pre-amp (such as built into a mixer, or a stand-alone unit).
(Note: Make sure to set
the pre-amp to the proper gain level—too much gain may distort subsequent amplifiers and too little may result in a noisy
signal)
The SCM 960 can be connected to your mixer or phantom power supply using a standard balanced 3-pin XLR microphone
cable. Before connecting to a mixer directly, turn the channel to which you’re connecting to its lowest gain setting. If you are
using the Nady SMPS-1 Phantom Power Supply, connect in the following order:
1. Connect the SCM 960 to the SMPS-1
2. Connect the SMPS-1 Signal Output to your mixer
3. Connect the SMPS-1 to the AC power supply (115—230VAC)
4. Turn on the SMPS-1 Power ON/OFF switch
5. Slowly turn up the channel gain in your mixer to the desired level
USING THE FOAM WINDSCREEN
CONNECTING THE SCM 960
Type: True condenser pressure-gradient microphone w/1” diaphragm and
FET pre-amplifier
Polar pattern: Cardioid /Omni
Sensitivity:
16mV/Pa
Frequency range: 25Hz to 20KHz
Impedance: < 200 Ohms
Max. SPL (1% THD @1000Hz): 125dB
Equivalent noise level to IEC 268-4(A weighted): 19dB
S/N ratio re 1Pa: 76dB
SPECIFICATIONS
Specifications subject to change for improvement purposes
SERVICE
(U.S.) Should your Nady microphone require service, please contact the Nady Service Department via phone at
(510) 652-2411 or e-mail at service@nady.com
(INTERNATIONAL) For service, please contact the Nady distributor in your country through the dealer from whom you
purchased this product.
Do not attempt to service this unit yourself as it will void your warranty
WARNING
USING THE OPTIONAL MICROPHONE SHOCK MOUNT
05/5/05
Power requirement: +48VDC phantom power
Current consumption: <3mA
Controls: Cardioid/Omni pattern select, -10dB, 0, -20dB attenuation select
Connector: 3-pin XLR (gold plated)
Mic cable: 3-pin XLR standard cable (not supplied)
Size: Diameter: 2.0" (50.5mm), Length: 5.25" (133mm)
Net weight: 11 oz (311g)
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Nady Systems Microphone SCM 1000 User manual
-
Nady Systems SCM920 User manual
-
-
-
Pyle PDMIC78 Owner's manual
-
Pyle PDMIC58 User guide
-
MAONO PM320S User manual
-
Coomber 1915 User manual
-
Svive hydra User manual
-