User's Manual
2
Safety Instructions
1. Read Instructions -– All the safety and
operation instructions should be read
before the Sunfire Component is
operated.
2. Retain Instructions — The safety and
operating instructions should be kept for
future reference.
3. Heed Warnings — All warnings on the
Component and in these operating
instructions should be followed.
4. Follow Instructions — All operating and
other instructions should be followed.
5. Water and Moisture — The Component
should not be used near water - for
example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet
basement, or near a swimming pool, etc.
6. Ventilation — The Component should be
situated so that its location or position
does not interfere with its proper ventila-
tion. For example, the Component should
not be situated on a bed, sofa, rug, or
similar surface that may block any
ventilation openings; or placed in a built-in
installation such as a bookcase or cabinet
that may impede the flow of air through
ventilation openings.
7. Heat — The Component should be
situated away from heat sources such as
radiators, or other devices which produce
heat.
8. Power Sources — The Component
should be connected to a power supply
only of the type described in these
operation instructions or as marked on the
Component.
9. Power Cord Protection — Power-supply
cords should be routed so that they are
not likely to be walked upon or pinched by
items placed upon or against them,
paying particular attention to cords at
plugs, convenience receptacles, and the
point where they exit the Component.
10. Cleaning — The Component should be
cleaned only as recommended in this
manual.
11. Non-use Periods—The power cord of
the Component should be unplugged from
the outlet when unused for a long period
of time.
12. Object and Liquid Entry — Care
should be taken so that objects do not fall
into and liquids are not spilled into the
inside of the Component.
13. Damage Requiring Service — The
Component should be serviced only by
qualified service personnel when:
A. The power-supply cord or the plug has
been damaged; or
B. Objects have fallen, or liquid has spilled
into the Component; or
C. The Component has been exposed to
rain; or
D. The Component does not appear to
operate normally or exhibits a marked
change in performance; or
E. The Component has been dropped, or its
cabinet damaged.
14. Servicing — The user should not
attempt to service the Component beyond
those means described in this operating
manual. All other servicing should be
referred to qualified service personnel.
User's Manual
3
15. To prevent electric shock, do not use
this polarized plug with an extension cord,
receptacle or other outlet unless the
blades can be fully inserted to prevent
blade exposure.
Pour préevenir les chocs électriques ne
pas utiliser cette fiche polariseé avec un
prolongateur, un prise de courant ou une
autre sortie de courant, sauf si les lames
peuvent être insérées à fond sans laisser
aucune pariie à découvert.
16. Grounding or Polarization —
Precautions should be taken so that the
grounding or polarization means of the
Component is not defeated.
Safety Instructions ....................................... 2
Introduction .................................................. 4
Features....................................................... 4
Unpacking .................................................... 4
Care ....................................................... 4
Overview ...................................................... 5
Control panel features ................................. 6
Installation .................................................... 8
Connections ................................................. 9
Location ..................................................... 10
System configurations ............................... 11
Adjusting the controls ................................ 15
Specifications............................................. 16
Troubleshooting guide ............................... 17
Limited warranty ........................................ 19
Service assistance ..................................... 19
Contents
To find out more about this and other Sunfire products,
please visit our website: www.sunfire.com
This apparatus does not exceed the Class
A/Class B (whichever is applicable) limits
for radio noise emissions from digital
apparatus as set out in the radio
interference regulations of the Canadian
Department of Communications.
ATTENTION — Le présent appareil
numérique n'émet pas de bruits
radioélectriques dépassant las limites
applicables aux appareils numériques de
class A/de class B (selon le cas)
prescrites dans le règlement sur le
brouillage radioélectrique édicté par les
ministere des communications du
Canada.
WARNING:THIS SUBWOOFER IS CAPABLE OF PRODUCING
SOUND PRESSURE LEVELS IN EXCESS OF 110 dB. YOU
MUST TAKE EVERY PRECAUTION TO PROTECT YOUR
HEARING FROM PERMANENT DAMAGE.
User's Manual
4
Your Sunfire Subwoofer should reach
you in perfect condition. If you do notice
any shipping damage, please contact
your Sunfire Dealer immediately.
Gently lift out the unit and remove all
the packing material. It is important to
save all the packing materials and the
box in case your subwoofer ever needs
to be moved or shipped for repair.
Make sure that you keep your sales
receipt. It is the only way to establish the
duration of your Limited Warranty and it
may come in useful for insurance
purposes.
Please take a moment to fill out and
mail the Sunfire Warranty Registration
card. Also read the serial number located
on the control panel and record it here:
Unpacking
Features
• High power, high efficiency amplifier
• Very low distortion
• Long throw, premium quality drivers
• Extremely compact size
• Automatic signal-sensing turn-on and
standby mode
• Line level unbalanced inputs
• Speaker level binding post inputs
• Line level high-pass outputs
• Flat/Video contour switch
• Continuously variable phase control
• Continuously variable crossover
frequency adjustment
• Continuously variable volume level
control
• Soft clipping circuit allows graceful
overload and prevents speaker
damage due to clipping
• Gold-plated inputs and outputs.
Dear Friend:
Thank you for purchasing my Sunfire
True Subwoofer MK IV. I hope you enjoy
it and the music it makes as much as I
have enjoyed creating it for you.
The big breakthrough features of the
subwoofer are its uncanny tracking
downconverter and its long throw, high
back-electromotive force driver. Taken
together, they provide this subwoofer
with as much bass as you could get from
several 15 inch drivers mounted in a
cabinet the size of a small refrigerator.
Introduction
Serial Number:
Purchased from:
Date:
Care
To maintain the speaker cabinet’s
finish, first unplug the power cord and
then use a soft, slightly dampened cloth
to clean the surfaces and finish off with a
dry cloth.
To keep the large rubber surrounds
soft and supple for 20 years or more,
treat them with MINK OIL, available at
most shoe repair stores. Rub a generous
amount into the surrounds with a soft
cloth about once a year (more often if
you live in a dry climate).
If your Sunfire Subwoofer needs
servicing, please read the Troubleshoot-
ing section on page 17. If a problem still
persists, contact your nearest authorized
Sunfire Dealer.
User's Manual
5
Your Sunfire Subwoofer is designed to
give you the best possible low-frequency
sound quality for your home theater
experience. It incorporates a tremen-
dously powerful built-in amplifier and a
pair of drivers to produce tight, floor-
rumbling bass down to 18 Hz, that you
can feel as well as hear.
The subwoofer has an adjustable high
cut filter and a choice of speaker-level or
line-level inputs for easy incorporation
into existing systems, or as part of a
subwoofer/satellite speaker combination.
The Woofer
To have lots of bass requires moving
lots of air. Your Sunfire Subwoofer
incorporates two drivers that can move
back and forth approximately five times
more than a normal subwoofer. This
gives it a lot of air moving capacity
which allows for majestic bass perfor-
mance.
Two drivers share the acoustic output.
Sometimes one driver appears to be
moving more than the other. They both
move the same amount only when
operating at the limit of their excursion
and power output, or when bass
requirements and music requirements
demand maximum output from the
system. Otherwise, the power is shared
between the two drivers in a way that
depends on the momentary amplitude
and the momentary musical spectrum. It
is normal for one or the other to move
more or less than its mate during
operation.
On the driver to the left of the control
panel there is a slight bump, under
which is a pressure cap. The bump is
normal. The driver on the right is
absolutely flat and very rugged. The one
with the slight bump is not quite as
rugged, and modest care should be
taken with it, though it is still very strong.
During installation, you should position
the driver with the bump towards a
protected side.
The Amplifier
The large movement range of the
drivers creates greater air pressure
inside the box than a conventional
woofer. Therefore, the drive amplifier
must be much more powerful than an
ordinary woofer amplifier. In fact, it has
to be so powerful that it is almost hard to
believe.
The power amplifier within your Sunfire
Subwoofer is capable of delivering over
2,700 watts into a 3.3 ohm resistor (the
voice coil resistance of the subwoofer’s
driver). When the same full output is
applied to the driver, however, the
enormous back-electromotive force
generated as a consequence of its large
motion and giant magnet causes the
current flow to be much less than if it
were a 3.3 ohm resistor. It is this singular
property of the driver that allows the
woofer to be approximately ten times
more efficient than a woofer this size
would normally be. Hence, the actual
average input power is substantially less
than 2,700 watts, and is approximately
270 watts for most musical material on
the loudest passages.
A compressor circuit kicks in automati-
cally if the input signal level reaches a
level that would overload the driver. This
maintains a ceiling on the output without
clipping.
If the input signal is driven even
further, a ‘soft clipping’ circuit is enabled.
This allows the woofer to put more sound
into the room to satiate the power hungry
user, but without distortion or damage to
the woofer. Thus, for explosive scenes in
movies, this produces extremely high
sound pressure levels (SPL) in your
room without the woofer banging against
its mechanical stops.
If you would like more detailed
information regarding the subwoofer
design, please call us and we will send
you a copy of our subwoofer technical
white paper, or you can view it on our
website: www.sunfire.com.
Overview
User's Manual
6
FUSE
1
2
3
4
5
678910
1. Power/Auto on Indicator
This light is bright when the subwoofer
is on, and dim when the subwoofer is
in its standby mode. This is controlled
by the AUTO ON/OFF circuit. The
presence of an audio signal turns the
unit on. After approximately fifteen
minutes of signal absence, the
subwoofer will go to its standby mode.
The light will only go off when the unit
is unplugged from the wall.
2. Volume Control
This control lets you match the output
level of the subwoofer to the level of
your satellite/main speakers. The
subwoofer output will increase as the
volume control is rotated clockwise.
When you have just installed your
system, turn this down first before
turning on your subwoofer. This will
prevent any loud surprises.
3. Crossover Frequency
This controls the high frequency cutoff
point. With the control rotated fully
clockwise, the subwoofer will repro-
duce frequencies up to 100 Hz. With
the control fully counter-clockwise the
subwoofer reproduces up to 35 Hz.
Rotate the control until the bass
sounds natural. If the mid-bass sounds
natural but you want more low bass,
turn the crossover frequency down a
little, then turn the volume control up
by about the same amount. This
increases the low-bass output while
leaving the mid-bass output the same.
4. Phase Control
This control changes the relative phase
of the subwoofer with respect to your
other speakers. Use this control to help
blend the subwoofer with the rest of
your system. This is accomplished by
adjusting the control in small incre-
ments as you listen for the most bass
at your listening position. As a final
trim, readjust the crossover and
volume controls after the phase control
has been set.
5. Flat/Video Contour Switch
When this switch is set to FLAT, the
frequency response extends down to
18 Hz. This is the recommended
setting for most audio and video
applications.
When set to Video Contour, a low
frequency roll-off is introduced
commencing below approximately
30 Hz. This setting may be used if your
Control Panel Features
User's Manual
7
system or neighbors are disturbed by
ultra low bass.
6. High Level Inputs
Under normal conditions, the preferred
connection is through the Line Level
inputs. If this is difficult or not possible
in your system, then you can use the
High Level inputs. Also, if you
experience excessive noise or hum
with the Line Level inputs, often a
simple change to the High Level inputs
will result in a lower background noise
level.
Connect to the speaker-level output of
your amplifier or receiver using
speaker wire (see page 14). They can
accept bare wire, banana, dual-banana
or spade connections.
Your amplifier or receiver MUST
have common grounded outputs,
or it will be damaged if connected
to these High Level inputs.
7. Line Level Inputs
Connect with RCA type patch cords to
the line level outputs of your receiver
or preamp. Here are two examples:
If your preamplifier or receiver has a
single sub/LFE output, connect it to the
subwoofer’s left input jack (see page
11). There is no need to use the
subwoofer’s right input jack.
If you want to run your main/satellite
speakers full range, use a “Y” adapter
at the preamplifier outputs (see page
12). In this way, you can send the
preamplifier’s output signal to your
main amplifier and to the subwoofer at
the same time.
8. High Pass Outputs
Line level high-pass output signals are
available at these jacks. These are
active whenever a signal is present at
the inputs of the subwoofer. The high-
pass crossover is a passive network
with a fixed crossover frequency of
70 Hz and a 6 dB per octave slope.
We recommend using this high-pass
function with main/satellite speakers
that are small and not designed to
reproduce low frequencies. If your
main speakers are capable of
operating full range, then you will not
need to use the high-pass function.
To use the High Pass outputs, connect
the preamp outs of your preamp/
receiver to the subwoofer’s Line Level
inputs using good quality RCA type
patch cords. Then connect a second
patch cord from the subwoofer’s High
Pass outputs to the inputs of your main
amplifier (see page 13). This will allow
your main speakers to operate at
frequencies above 70 Hz and the
subwoofer to operate at frequencies
below 70 Hz.
9. Line Fuse
The 120 VAC model is supplied with a
conservative 6 1/4 amp slow-blow type
fuse to protect the electronics. It is
acceptable to use a 6 amp slow-blow
fuse.
The 230 VAC model has a 4 amp slow-
blow fuse.
Always unplug the power cord
before inspecting or changing the
fuse. Never use a fuse with a
current rating more than 6 1/4
amps for the 120 VAC model, or more
than 4 amps for the 230 VAC model.
10. Power Cord
120 VAC model
Plug into any 120 Volt 60 Hz outlet
with a circuit rating of 10 amps or more
(a typical home circuit is rated at 15
amps).
Never plug the 120 VAC model
directly into 220-240 Volts AC as
this will cause catastrophic circuit
failure.
230 VAC model
Plug into any 220-240 Volt 50/60 Hz
outlet with a circuit rating of 6 amps or
more.
User's Manual
8
Installation
Observe the following general
precautions and read the safety
instructions on pages 2 and 3 before
using your Sunfire Subwoofer.
• Never open the cabinet or remove
the metal control panel as this
might result in an electrical shock
to you or damage to the unit.
• Protect it from prolonged exposure
to direct sunlight and other direct
sources of heat, such as heating
vents and radiators.
• To prevent fire or shock, do not
expose the unit to rain or moisture.
If fluid or a foreign object should
enter the unit, immediately turn off
the power and contact your Sunfire
Dealer.
• Avoid excessive exposure to
extreme cold or dust.
• Do not place heavy objects on top
of the unit.
• Do not place the subwoofer with its
control panel against the floor.
• If you wish to place your woofer so
the drivers face the floor and
ceiling, thereby moving up and
down, use at least 1-1/2 inch high
spikes or feet for support. They
may be attached either with screws
or self-stick backing. This arrange-
ment will impart substantial house
and floor shaking motion.
• Four extra heavy, shock absorbing
rubber mounting feet have been
included. If your woofer tends to
wander about slightly while in use,
place these feet just inside the
existing feet positions. These shock
absorbing mounts will let the
woofer rock freely, thereby
absorbing low frequency rocking
energy, allowing it to adhere solidly
to the floor. To move the woofer
along the floor, rotate it onto one
edge and it will slide along easier.
Heat rise
• Allow adequate ventilation around
the metal control panel of the
subwoofer.
• Do not let anything come into
contact with the panel and keep at
least two inches away from any
walls.
The metal control plate serves as the
amplifier heat sink and also as a conduit
to remove internal heat to the outside
and into the atmosphere. It can reach
temperatures of 60 degrees C, which will
feel hot to the touch, using nerves of
flesh and blood as temperature sensors.
As uncomfortable as it may feel, 60
degrees C cannot burn you, and in fact is
almost cool to copper, silicon, steel, and
aluminum, the materials from which your
woofer is constructed.
AC Power Considerations
Ensure that the unit is plugged into an
outlet capable of supplying the correct
voltage specified for your model.
Unplug your subwoofer’s power cord
from the electrical outlet if it will be left
unused for a long period of time.
NOTE: Never remove the ground
pin from any power cords. This is
very dangerous.
Route the power-supply cord so it is
not likely to be walked on or pinched by
items placed upon or against it,
especially at plugs, convenience
receptacles, and the point where it exits
from the unit.
Magnetic Fields
We recommend that you place your
woofer further than two feet away from
your TV, VCR, tape deck or computer,
so the speaker’s magnet won’t distort the
colors of your TV picture or erase your
video tapes, audio tapes or computer
discs.
User's Manual
9
Please consider the following when
setting up your new system :
• Before making or changing any
connections, ALWAYS make sure
that the subwoofer is unplugged
from the wall and your other
components are turned OFF. Also
turn down the volume control of the
subwoofer and your preamplifier or
receiver.
• This diagram shows all the low
power components sharing a power
strip which is connected to the
same outlet used by the amplifier.
• The subwoofer is connected to an
outlet on the same circuit breaker,
provided that the total system
current draw does not exceed the
breaker current rating.
• This arrangement will reduce the
possibility of an audible hum in your
system caused by a ground loop.
• Whenever possible, keep the
powercords away from the signal
cables or speaker wires to prevent
any hum or interference being
heard in the speakers.
• Choose reliable, high quality
interconnect cables, also called
patch cords or RCA cables. They
should be fully shielded and as short
as possible for the job. The longest
cable in your system will likely be
to the subwoofer, so choose a
good quality brand.
• Some patch cords can be a very
tight fit and there is usually a
preferred method of getting them
off. Some have to be removed with
a twisting action. Be gentle or you
may damage the jacks of the
subwoofer or your other compo-
nents.
Speaker Level connections
• The subwoofer’s Speaker Level
inputs can accept speaker wires
with banana, dual-banana, bare
wire or spade terminals. If you
have banana type connectors on
your speaker wire, make sure that
you tighten the binding posts
before inserting.
• Make sure that the negative
speaker wires never touch the
positive wires as this will short out
and possibly damage your amplifier
or receiver.
The subwoofer’s two negative
posts are joined internally
(common-grounded). Your
amplifier must also be internally
common-grounded or you cannot
use this connection. Contact the
manufacturer of your amplifier to
make sure its outputs are common
grounded.
Tape Deck
DVD
Preamplifier
Power strip
Subwoofer
Amplifier
AC outlets on the same circuit breaker
Connections
User's Manual
10
Your Sunfire Subwoofer is designed to
be placed in a corner and this will
produce optimum performance.
Experiment with at least two corners and
then decide which is the best.
#1 is very good positioning.
#2 is also excellent but may shake the
back wall too much and cause
things on or along the wall to rattle
too much. If this occurs, use the #3
position:
#3 Move the woofer approximately
three feet away from the right wall
and place it along the back wall as
shown. This will substantially
reduce the rattling of the back wall
and will still pressurize the room
with lots of bass.
Although low frequencies are non-
directional, factors such as room
reflections, standing waves, resonance
and absorption strongly affect your
subwoofer’s performance.
Moving the subwoofer from one corner
to another can have a major effect on the
bass response.
Remember to keep it at least
two or three feet away from any
TV screen, computer, VCR or
magnetic tapes and discs. This
will reduce the chance of the magnetic
fields upsetting the TV screen or erasing
your magnetic media.
Also position the control panel so that
it is not touching anything and can
receive good ventilation.
Location
Using Two Subwoofers
If you wish to use two woofers, the
sound output will double (an increase of
6 dB). Locate the woofers with one in
each corner and experiment with the
location and phase control to achieve the
best bass response.
Always drive each woofer through the
Left/Mon input even though you are
driving one woofer with a right channel
drive and the other with a left channel
drive. If your preamplifier has a single
sub/LFE output, use a Y cable to split it
into two outputs.
User's Manual
11
System Configurations
If your preamplifier has a
subwoofer output (often
labeled LFE for Low
Frequency Effects), it can
be connected to the
subwoofer’s Left (Mono)
input as shown. This is the
simplest and recom-
mended connection. A
receiver with a sub/LFE
output can be connected
in the same way.
The subwoofer will play
the low frequency range
and the other speakers will
play the frequency range
delivered to them by your
amplifier.
If you have a home
theater preamplifier, it may
have an independent
subwoofer volume control.
Make sure this is correctly
adjusted, and that the
Sunfire Subwoofer’s
crossover frequency is set
to 100 Hz. This is by no
means an iron-clad rule,
rather it is a good starting
point. (See the crossover
frequency control details
on page 6 and adjust-
ments on page 15).
You can set the
subwoofer’s Bass Level
control to 0dB, and then
use the preamplifier’s
subwoofer level control for
normal and routine
adjustments.
PREAMPLIFIER
MAIN
OUTPUTS
R
SUB/LFE OUT
R
L
L
AMPLIFIER
INPUTS
TO FRONT SPEAKERS
Connections to a preamplifier’s subwoofer output
The following pages show some typical connections that you might make in your
installation. They show how the inputs and outputs of the Sunfire Subwoofer are
connected to your preamplifier or receiver.
User's Manual
12
PREAMPLIFIER
MAIN
OUTPUTS
R
R
L
L
AMPLIFIER
INPUTS
TO FRONT SPEAKERS
Y CABLES
If your preamplifier does
not have a sub/LFE
output, you can use “Y”
cables to send its main
outputs to both the
subwoofer and your
amplifier.
The subwoofer will play
the low frequency range
and your front speakers
will play the full range.
Although bass is
commonly distributed
evenly between left and
right channels (L+R bass),
movie soundtracks often
contain differential (L-R)
bass. The opening scene
in “Top Gun”, for example,
has loads of L-R bass
information. If this is not
preserved, the bass in
these scenes sounds
anemic. The Sunfire
Subwoofer utilizes
differential gain on the left
and right inputs to retain
both the L+R and L-R
information. Therefore,
systems which do not
have a dedicated sub/LFE
output should use both
the left and the right inputs
as shown, for the greatest
bass impact.
An alternative connec-
tion method without using
Y cables is shown on the
next page.
If your preamp/receiver
has a dedicated sub/LFE
output, then only the Left
(Mono) input is used, as
shown on the previous
page.
Connections to a preamplifier using Y cables
User's Manual
13
If you are using a
preamplifier which does
not have a sub/LFE
output, you can send its
left and right front output
into the subwoofer’s Line
Level inputs and then
connect the subwoofer’s
High-Pass outputs to the
inputs of your amplifier.
The subwoofer will play
the low frequencies and
your amplifier and front
speakers will play the
frequency range above the
subwoofer’s fixed high-
pass crossover point.
The signals coming out
of the subwoofer’s high-
pass outputs are not
affected by any of the
controls. They are just a
copy of the signals going
in except that the low bass
is filtered out. This uses
the subwoofer’s passive
crossover network, rather
than the active network
and controls.
PREAMPLIFIER
MAIN
OUTPUTS
R
R
L
L
AMPLIFIER
INPUTS
TO FRONT SPEAKERS
R
L
Using the line level high-pass outputs
User's Manual
14
If you are using a
receiver which does not
have a subwoofer output or
line level outputs (pre-outs),
you can connect its
speaker outputs to the
subwoofer’s Speaker-Level
inputs. The front speakers
can still be connected to
your receiver.
The subwoofer’s internal
amplifier supplies the
power to reproduce the low
frequency range. It receives
a sample of the signal
going to your front
speakers. (An insignificant
fraction of your receiver’s
power is transferred to the
subwoofer).
There is no need to use
the Speaker Level inputs if
you are using a separate
amplifier and preamplifier.
Such systems are best
connected using the Line
Level inputs as shown in
the previous diagrams.
If you are using the Line
Level inputs and there is a
excessive amount of noise
or hum present, using the
Speaker Level inputs may
yield a lower background
noise level.
Your receiver MUST
have common
grounded outputs, or
it will be damaged if
connected to the
subwoofer’s Speaker
Level inputs.
TO FRONT SPEAKERS
R
L
RECEIVER
MAIN
OUTPUTS
Using the speaker level inputs
User's Manual
15
There are two main methods for
adjusting the level, crossover frequency
and phase of the Sunfire Subwoofer to
match a system:
• Bob Carver’s preferred method:
By listening and making the
adjustments to suit your taste.
• Laboratory method:
By measuring the output and
adjusting for a flat frequency
response.
Excellent results can be obtained if
you make the adjustments based on
simply listening. This is Sunfire’s
preferred method as it allows the system
to be voiced based on what sounds the
best, whereas laboratory-flat frequency
response can often be clinical and less
than exciting.
The following procedure is for those
who prefer a more methodical and
scientific approach. This excerpt is from
“The Audio Critic,” issue 24, page 31,
written by contributing editor David Rich,
and is reprinted here with their kind
permission.
You will need a test CD with low-
frequency warble tones, and a sound
pressure-level meter. The Radio Shack
®
SPL meter will do fine, as will the
Stereophile
®
test CD.
“Step 1. Disconnect the subwoofer
and run the main speaker with a tone in
its passband (80-100Hz). Measure the
level.
Step 2. Disconnect the main speaker
and reconnect the subwoofer. Set the
subwoofer to its highest crossover
frequency. Set the level control of the
subwoofer to give the same sound
pressure level with the same tone you
used in Step 1.
Adjusting the controls
Step 3. With both the subwoofer and
the main speaker connected, measure
the level of the tones at the available
frequencies. Because the crossover is
set too high, you will have a peaked
response. Adjust the crossover control to
get the smoothest response.
Step 4. Use the phase control to make
the response even smoother. It has its
biggest effect at the crossover fre-
quency. You can iterate between the
crossover and the phase controls. Keep
your hands off the level control! It was
set correctly in step 2.
Step 5. Listen to the subwoofer.
Resist all temptations to turn up the level
control. Play something with really deep
bass to confirm that your subwoofer is
working.”
Control settings
Use this drawing to record some of
your favorite settings.
User's Manual
16
Specifications
Amplifier Output
2,700 watts rms (3.3 Ω impedance)
High Cut Filter
35 Hz - 100 Hz Adjustable.
Frequency Response
18 Hz - 100 Hz
Power Line Voltage
US model
120 VAC 50/60 Hz
International model
230 VAC 50/60 Hz
Dimensions
11" x 11" x 11"
Weight
48 lbs
Finish
Black anodize and black lacquer.
Line power consumption:
600 W average, 18 Hz to 80 Hz, at
absolute maximum continuous output.
8 watts at idle.
2700 W peak, time limited basis.
Output levels:
Greater than 110 dB peak SPL
(includes room gain) from 18 Hz to
80 Hz.
A typical Sunfire subwoofer can be
expected to ‘best’ its specified minimum
peak SPL by several decibels.
Total Harmonic Distortion
Typically less than 1/10 of the funda-
mental between 18 to 80 Hz.
Measurement method is near field, dual
microphone technique. Distortion
decreases with decreasing level.
Input sensitivity for full output:
250mVrms from left input with volume
control at 0dB, 60mVrms with volume
control fully clockwise
*
0.75Vrms from right input with volume
control at 0dB, 200mVrms with volume
control fully clockwise
*
Input impedance:
12 kΩ for Line-Level inputs
15 kΩ for Hi-Level inputs
Driver:
Extra large magnet and long throw
mechanical design yield very high back-
emf. The result is extraordinarily high
operating efficiency – that is, more
acoustic output for each watt of input.
Internal system gain:
50dB from left input jack to speaker with
the Bass Level control at 0dB, 62dB with
the control fully clockwise
*
40dB from right input jack to speaker
with the Bass Level control at 0dB, 52dB
with the control fully clockwise
*
*
The Sunfire Subwoofer utilizes
differential gain on the left and right
inputs to retain both L+R and L-R
information.
© 2001 Sunfire Corporation.
All rights reserved. Sunfire Corporation
reserves the right to improve its products
at any time. Therefore, specifications are
subject to change without notice.
Manual part number 913-016-00 Rev D
User's Manual
17
Troubleshooting
The Sunfire Subwoofer is expertly
designed and built to provide years of
trouble-free performance. Most
problems that occur can usually be
solved by checking your setup or
making sure that the components
connected to the amplifier are on and
fully operational.
The following information will help you
deal with common problems you may
experience during normal use. If a
problem still persists, please contact
your Sunfire Dealer for assistance.
Not enough bass
• Check that the input connections are
going to the input terminals and not the
output terminals. In other words, the
connections from your preamplifier
must go to the subwoofer’s line level
inputs instead of the line level high
pass outputs. If they are connected to
the outputs by mistake, the bass will be
weak but the subwoofer will still
function.
• If your preamplifier has a single
subwoofer/LFE output jack, make sure
it connects to the subwoofer’s Left
(Mono) input. If the bass is still not
enough after checking all the remaining
points, use a Y cable to connect the
preamplifier’s single subwoofer/LFE
output to the subwoofer’s right and left
inputs.
• Make certain the woofer is in a corner
location, firing at 45 degrees into the
walls formed by the corner. This is not
absolutely essential, but will maximize
the bass output and give the smoothest
possible response. If you place the unit
so one of the drivers is firing into one of
the walls, leave three inches of
clearance between the driver and the
wall.
• Home theater preamplifiers usually
have a way of adjusting the level of the
subwoofer/LFE output, either using a
remote control or with a small volume
knob on the back panel. Make sure that
this is adjusted correctly.
• If the preamplifier’s subwoofer/LFE
output has an adjustable crossover
frequency, make sure that the
subwoofer’s own crossover point is set
higher or part of the bass range will be
missing.
Not enough bass in a 5.1
system
• 5.1 home theater preamplifiers usually
have a bass management system which
allows the bass to be redirected among
your speakers. For example, the bass
normally present in the front speakers
can be redirected to play in the
subwoofer, or the subwoofer can play
the bass from all the speakers, in
addition to its dedicated LFE (low
frequency effects) channel. Make sure
that all of the bass management options
are correctly set. The preamplifier may
have a way of turning the subwoofer
output off entirely, so check that it is
always on.
• Check that the preamplifier calibration
procedure is correctly adjusted. Usually,
the preamp will send a test tone through
all the speakers in your system,
allowing you to adjust (trim) the volume
of each channel until they are all playing
at the same level.
• If the bass is weak only when playing
5.1 surround sources, check that your
preamplifier is correctly set to decode
the 5.1 surround modes, such as Dolby
Digital or DTS.
• Some DVD discs have a menu which
allows you to select which soundtrack to
play. Check that the correct 5.1
surround audio soundtrack is selected,
otherwise it may just play stereo into
your preamp and you won’t get the true
LFE signal into the subwoofer.
User's Manual
18
Hum
Adding any component such as a
subwoofer to an existing system will
often give rise to a hum which wasn’t
there before. Your first thought may be
that the subwoofer has a problem, but
this is more than likely caused by a
“ground-loop” in your system.
Follow these steps to isolate the main
cause of the ground-loop hum (there
may even be more than one cause).
• Try to have all of your equipment on
the same electrical outlet or circuit, see
page 9 for more details.
• If your subwoofer is a fair distance
away from your other equipment, you
may use a 15 amp extension cord as
long as it has a ground connection.
NOTE: Never remove the ground
pin from any power cords. This is
very dangerous.
• Turn off all components in your
system, including the subwoofer,
amplifiers and the preamplifier, before
disconnecting or connecting cables.
• First remove every connection from the
subwoofer to the rest of your system.
Plug the subwoofer power cord back in
and check for the hum. If it is still there,
try plugging it into a different outlet in
case it is picking up interference on the
AC line.
• If you have followed the above
guidelines for the power connections
and a hum is still present, then there is
one very common problem to consider:
a “ground-loop” introduced by connect-
ing a cable TV line to a VCR or TV,
which is then connected to the preamp.
This can be addressed as follows:
• Disconnect all cables which come from
outside the room, such as cable TV,
satellite TV, or roof top antennas. Make
sure that they are disconnected where
they first enter the room, so they are
making no connection to your preampli-
fier, TV, or any other component. If the
hum is caused by the cable TV line,
then you will need a “ground-loop
isolator.” This is an inexpensive device
fitted in line with the coaxial cable feed.
• If the hum persists, disconnect all the
source components one at a time from
the back of the preamplifier until you
identify the problem.
• If you are using the subwoofer’s Line
Level inputs and there is a excessive
amount of noise or hum present, using
the Speaker Level inputs may yield a
lower background noise level.
• Ground-loop isolators are available for
audio lines and video. Once you have
identified which components are
causing a problem, you can fit the
isolators between the component and
the preamplifier.
The subwoofer won’t turn off
• The subwoofer should turn itself off
after approximately fifteen minutes with
no audio signal present. If not, check
there is no background hum. The
subwoofer may sense hum as a small
signal and stay on. See the above hints
to eliminate the hum.
The subwoofer won’t turn on
• The subwoofer’s volume control may be
turned down or no signal is received
from your preamplifier.
• Check the input connections.
• Check the mode switch on surround
systems to be certain that a bass signal
is being sent to the subwoofer.
Audible snap from outlet
• When the subwoofer is initially plugged
into the wall, there is an in-rush current
surge as the power supply capacitors
charge up. This may give rise to an
audible snap from the outlet as the plug
is inserted. This can be avoided by
plugging the subwoofer into a switched
outlet or switched power strip (rated at
15 Amps or more).
User's Manual
19
Limited Warranty
Sunfire Corporation is proud of its
products which have been built with care
using advanced technology and premium
component parts. Your unit has been
crafted to perform properly for many
years. Sunfire Corporation offers the
following Warranty to you, the owner of a
new Sunfire product:
The Sunfire Corporation Warranty for
the Subwoofer MK IV is in effect for
TWO years from the date of original
retail purchase. The Sunfire Corporation
Warranty covers defects in materials and
workmanship. The following, however,
are excluded:
a) Damage caused during shipment.
b) Damage caused by accident,
misuse, abuse of operation
contrary to the instructions
specified in the Sunfire Corporation
user’s manual
c) Units where the serial number has
been defaced, modified or
removed,
d) Damage resulting from modifica-
tion or attempted repair by any
person not authorized in writing by
Sunfire Corporation.
The Sunfire Corporation Warranty
extends to the original owner or
subsequent owner(s) during the two year
warranty period so long as the original
dated purchase receipt is presented
whenever warranty service is required.
All implied warranties, including
warranties or merchantability and fitness
for particular purposes, are limited in
duration to the two year length of this
Warranty, unless otherwise provided by
state law.
Sunfire Corporation’s liability is limited
to the repair or replacement, at our
option, of any defective product and shall
not in any event include property or any
other incidental or consequential
damages which may result from the
failure of this product.
Some states do not allow limitations on
how long an implied warranty lasts and/or
do not allow the exclusion or limitation of
incidental or consequential damages, so
the above limitations or exclusions may not
apply to you.
This Warranty gives you specific legal
rights, and you may also have other
rights which vary from state to state. We
suggest that you attach your purchase
receipt to this Warranty and keep these
in a safe place. Thank you for your
choice of a Sunfire Corporation product.
Service Assistance
We suggest that you read the Limited
Warranty completely to fully understand
your Warranty/Service coverage.
If your Sunfire Corporation product
ever requires service, write to us, or call:
Sunfire Corporation
Technical Services Department
P.O. Box 1589
Snohomish, WA 98290
Tel (425) 335-4748
Fax (425) 335-4746
You will be directed to an authorized
Sunfire Corporation Service Station or
receive instructions to ship the unit to the
factory. Please save the original shipping
carton and packing materials in case
shipping is required. Please do not ship
Parcel Post.
NOTE: Before sending in your unit for
repair, you must call Sunfire for return
authorization.
Include a complete description of the
problem, indicating how you have it
connected, the associated equipment in
your system and a copy of your purchase
receipt. Initial shipping costs are not paid
by Sunfire Corporation; return ground
shipping costs will be prepaid if repairs
were covered by the scope of this
Warranty.
Manual part number 913-016-00 Rev D
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sunfire True Subwoofer Signature User manual
-
Sunfire True Subwoofer Architectural Signature User manual
-
Sunfire True Subwoofer Architectural User manual
-
Sunfire TS-SJ8 User manual
-
Sunfire HRS-10 User manual
-
Sunfire Solitaire 10 User manual
-
Sunfire XTEQ12 User manual
-
Sunfire SRS-210R User manual
-
Sunfire Atmos XTATM265230 User manual
-
Sunfire True Subwoofer EQ User manual
