Emerson EWC19T4 User manual

Brand: Emerson

Model: EWC19T4

Category: CRT TVs

Type: User manual

COLOR TV/VCR/DVD TRIPLE COMBO

EWC19T4

(19 inch)

OWNER’S

MANUAL

As an ENERGY STAR

Partner, our company has

determined that this product meets

the E

NERGY STAR guidelines for

energy efficiency. E

NERGY STAR

is a U.S. registered mark.

If you need additional operating assistance after reading this owner’s

manual or to order replacement accessories, please call

TOLL FREE : 1-800-256-2487.

Or visit our WEB SITE at http://www.funai-corp.com

Please read before using this equipment

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

SUPPLIED ACCESSORIES

Batteries

Remote Control Unit

ACCESSORIES

2 AA Batteries

NE223UD

PART NO.

Owner’s Manual 1EMN20183

“EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS

OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.”

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 1

1.Read instructions-All the safety and operating instructions

should be read before the appliance is operated.

2.Retain Instructions-The safety and operating instructions

should be retained for future reference.

3.Heed Warnings-All warnings on the appliance and in the

operating instructions should be adhered to.

4.Follow Instructions-All operating and use instructions

should be followed.

5.Cleaning-Unplug the unit from the wall outlet before clean-

ing. Do not use liquid cleaners or aerosol cleaners. Use a

damp cloth for cleaning.

EXCEPTION: A product that is meant for uninterrupted

service and, that for some specific reason, such as the possi-

bility of the loss of an authorization code for a CATV con-

verter, is not intended to be unplugged by the user for clean-

ing or any other purpose, may exclude the reference to

unplugging the appliance in the cleaning description other-

wise required in item 5.

6.Attachments-Do not use attachments not recommended by

the unit manufacturer as they may cause hazards.

7.Water and Moisture-Do not use this unit near water-for

example, near a bath tub, wash bowl, kitchen sink, or laun-

dry tub, in a wet basement, or near a swimming pool, and

the like.

8.Accessories-Do not place this unit on an unstable cart,

stand, tripod, bracket, or table. The unit may fall, causing

serious injury to someone, and serious damage to the appli-

ance. Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with the unit.

Any mounting of the appliance

should follow the manufacturer’s

instructions and should use a mount-

ing accessory recommended by the

manufacturer. An appliance and cart

combination should be moved with

care.Quick stops, excessive force,

and uneven surfaces may cause the

appliance and cart combination to

overturn.

AMEUBLES- Cet appareil ne doit

être placé que sur un meuble (avec

ou sans roulettes) recommandé par

le fabricant. Si vous l’installez sur

un meuble à roulettes, déplacez les

deux ensembles avec précaution.

Un arrêt brusque, l’utilisation

d’une force excessive et des sur-

faces irrégulières risquent de désta-

biliser l’ensemble et de le renverser.

9. Ventilation-Slots and openings in the cabinet and the back

or bottom are provided for ventilation and to ensure reliable

operation of the unit and to protect it from overheating, and

these openings must not be blocked or covered. The open-

ings should never be blocked by placing the unit on a bed,

sofa, rug, or other similar surface. This unit should never be

placed near or over a radiator or heat register. This unit

should not be placed in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or

the manufacturer’s instructions have been adhered to.

10.Power Sources-This unit should be operated only from the

type of power source indicated on the marking label. If you

are not sure of the type of power supply to your home, con-

sult your appliance dealer or local power company. For the

unit intended to operate from battery power, or other

sources, refer to the operating instructions.

11.Grounding or Polarization-This unit is equipped with a

polarized alternating-current line plug(a plug having one

blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try revers-

ing the plug. If the plug should still fail to fit, contact your

electrician to replace your obsolete outlet. Do not defeat the

safety purpose of the polarized plug.

12.Power-Cord Protection-Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying par-

ticular attention to cords at plugs, convenience receptacles,

and the point where they exit from the appliance.

- 2 - EN

1B15

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSON-

NEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

THIS SYMBOL INDICATES THAT DAN-

GEROUS VOLTAGE CONSTITUTING A

RISK OF ELECTRIC SHOCK IS PRESENT

WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE

ARE IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS IN THE

LITERATURE ACCOMPANYING THE

APPLIANCE.

The caution marking is located on the rear of the cabinet.

IMPORTANT SAFEGUARDS

PORTABLE CART WARNING

S3126A

SYMBOLE D'AVERTISSEMENT POUR

LES COMPOSANTES

APPAREIL ET MEUBLE A ROULETTES

S3126A

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 2

- 3 - EN

1B15

13.Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the unit, be sure the antenna

or cable system is grounded so as to provide some protec-

tion against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA

No. 70, provides information with respect to proper

grounding of the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna-discharge unit,

connection to grounding electrodes, and requirements for

the grounding electrode. (Fig. A)

14.Lightning-For added protection for this unit receiver dur-

ing a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system. This will

prevent damage to the unit due to lightning and power-line

surges.

15.Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them

might be fatal.

16.Overloading-Do not overload wall outlets and extension

cords as this can result in a risk of fire or electric shock.

17.Object and Liquid Entry-Never push objects of any kind

into this unit through openings as they may touch danger-

ous voltage points or short out parts that could result in a

fire or electric shock. Never spill liquid of any kind on the

unit.

18.Servicing-Do not attempt to service this unit yourself as

opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

19.Damage Requiring Service-Unplug this unit from the wall

outlet and refer servicing to qualified service personnel

under the following conditions:

a. When the power-supply cord or plug is damaged or frayed.

b. If liquid has been spilled, or objects have fallen into the

unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the oper-

ating instructions. Adjust only those controls that are cov-

ered by the operating instructions, as improper adjustment

of other controls may result in damage and will often

require extensive work by a qualified technician to restore

the unit to its normal operation.

e. If the unit has been dropped or damaged in any way.

f. When the unit exhibits a distinct change in performance-

this indicates a need for service.

20.Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same character-

istics as the original part. Unauthorized substitutions may

result in fire, electric shock, injury to persons or other haz-

ards.

21.Safety Check-Upon completion of any service or repairs to

this unit, ask the service technician to perform routine safe-

ty checks to determine that the unit is in proper operating

condition.

22.Heat-This unit product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

GROUND CLAMPS

NEC - NATIONAL ELECTRICAL CODE

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

S2898A

WIRE

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

ELECTRODE SYSTEM

(NEC ART 250, PART H)

SERVICE

EQUIPMENT

CLAMP

ANTENNA

L EAD IN

ANTENNA

POWER SERVICE GROUNDING

GROUND

ELECTRIC

FIGURE A

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 3

- 4 - EN

1B15

RADIO-TV INTERFERENCE

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

IMPORTANT COPYRIGHT INFORMATION

Unauthorized copying, broadcasting, public perfor-

mance and lending of discs are prohibited.

This product incorporates copyright protection tech-

nology that is protected by method claims of certain

U.S. patents and other intellectual property rights

owned by Macrovision Corporation and other rights

owners. Use of this copyright protection technology

must be authorized by Macrovision Corporation,

and is intended for home and other limited viewing

uses only unless otherwise authorized by

Macrovision Corporation. Reverse engineering or

disassembly is prohibited.

LASER SAFETY

This unit employs a laser. Only a qualified service

person should remove the cover or attempt to ser-

vice this device, due to possible eye injury.

CAUTION: USE OF CONTROLS OR ADJUST-

MENTS OR PERFORMANCE OF PROCE-

DURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK

DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est con-

forme à la norme NMB-003 du Canada.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA

PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE

ET POUSSER JUSQU’AU FOND.

PRECAUTIONS

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 4

- 5 - EN

1C29

AV OID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

LOCATION

For safe operation and satisfactory performance of

your unit, keep the following in mind when selecting

a place for its installation:

•

Shield it from direct sunlight and keep it away from

sources of intense heat.

•

Avoid dusty or humid places.

•

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes at

the top or bottom of the unit. Do not place the unit

on a carpet because this will block the ventilation

holes.

•

Install unit in a horizontal position.

•

Avoid locations subject to strong vibration.

•

Do not place the unit near strong magnetic fields.

•

Avoid moving the unit to locations where tempera-

ture differences are extreme.

•

Do not handle the power cord with wet hands.

•

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

•

If by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

•

Do not put your fingers or objects into the disc

loading tray of the unit.

•

Do not place anything directly on top of the unit.

WARNING

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place or

after heating a cold room or under conditions of high

humidity. If a DVD is played in a unit which has

moisture, it may damage the DVD and the unit.

Therefore when the condensation occurs inside the

unit, turn the POWER on and allow at least 2 hours

for the unit to dry out.

The serial number of this product may be found on the back of the unit. No other TV/VCR/DVD has the same

serial number as yours. You should record the number and other vital information here and retain this book as

a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

The following symbols below appear in some head-

ings and notes in this manual, with the following

meanings

: Description refers to TV/VCR operation (in the

TV/VCR mode).

: Description refers to playback of DVD video discs

(in the DVD mode).

: Description refers to playback of Audio CDs

(in the DVD mode).

: Description refers to playback of MP3 discs

(in the DVD mode).

: Description refers to the items to be set by the

QUICK mode (in the DVD mode).

QUICK

MP3

DVD-V

TV/VCR

SYMBOLS USED IN THIS MANUAL

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 5

- 6 - EN

1C29

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . .2, 3

C PRECAUTIONS . . . . . . . . . . . . . . . .4

LOCATION . . . . . . . . . . . . . . . . . . .5

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE .5

WARNING . . . . . . . . . . . . . . . . . . . .5

SYMBOLS USED IN THIS

MANUAL . . . . . . . . . . . . . . . . . . . . .5

C TABLE OF CONTENTS . . . . . . . . . .6

C FEATURES . . . . . . . . . . . . . . . . . . . .7

C OPERATING CONTROLS AND

FUNCTIONS . . . . . . . . . . . . . . . .9, 10

C PREPARATION FOR USE . . . . . . .11

ANTENNA/CABLE

CONNECTION . . . . . . . . . . . . . . . .11

CONNECTING TO EXTERNAL

INPUT JACKS . . . . . . . . . . . . . . . .12

INSTALLING THE BATTERIES . .12

EXTERNAL INPUT MODE . . . . . .12

CONNECTING TO A STEREO

AMPLIFIER EQUIPPED WITH DIGI-

TAL INPUT JACKS SUCH AS MD

DECK OR DAT DECK (for DVD) .13

CONNECTING TO A DOLBY

DIGITAL DECODER (for DVD) . .14

TV/VCR SECTION

C SET UP FOR USE . . . . . . . . . . . . .15

SELECTING THE LANGUAGE . .15

CLOCK SET UP

(AUTO / MANUAL) . . . . . . . . .15, 16

DAYLIGHT-SAVING TIME . . . . . .17

CHANNEL SET UP . . . . . . . . . . . .18

DELETING (OR ADDING)

CHANNEL(S) . . . . . . . . . . . . . . . . .18

C TV OPERATION . . . . . . . . . . . . . . .19

WATCHING A TV PROGRAM . . .19

DEGAUSSING . . . . . . . . . . . . . . . .19

PICTURE CONTROL . . . . . . . . . . .19

CLOSED CAPTION SYSTEM . . . .20

V-CHIP SET UP . . . . . . . . . . . . . . .21

C MTS(Multi-Channel Television

sound)SYSTEM . . . . . . . . . . . . . . . .23

CHECKING THE SELECTED

MTS MODE . . . . . . . . . . . . . . . . . .23

MTS RECORDING/MONITOR

MODE . . . . . . . . . . . . . . . . . . . . . .23

SELECTING THE MTS SYSTEM .24

C VIDEO CASSETTE . . . . . . . . . . . . .25

C PLAYBACK . . . . . . . . . . . . . . . . . . .26

NORMAL PLAYBACK . . . . . . . . .26

TRACKING ADJUSTMENT . . . . .26

SLOW MOTION . . . . . . . . . . . . . .26

PICTURE SEARCH . . . . . . . . . . . .26

STILL PICTURE . . . . . . . . . . . . . .26

VERTICAL HOLD CONTROL . . .26

C SPECIAL PLAYBACK . . . . . . . . . .27

RENTAL PLAYBACK . . . . . . . . . .27

AUTO REPEAT PLAYBACK . . . . .27

C SEARCH . . . . . . . . . . . . . . . . . . . . .28

ZERO RETURN . . . . . . . . . . . . . . .28

TIME SEARCH . . . . . . . . . . . . . . .28

INDEX SEARCH . . . . . . . . . . . . . .29

C SPECIAL FEATURES . . . . . . . . . .29

REAL TIME TAPE COUNTER . . .29

AUTO REWIND-EJECT . . . . . . . .29

C RECORDING . . . . . . . . . . . . . . . . .30

NORMAL RECORDING . . . . . . . .30

SKIPPING UNWANTED SCENES

DURING

RECORDING . . . . . . . . . . . . . . . . .30

OTR (One Touch Recording) . . . . . .31

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder) . . .31

C TIMER . . . . . . . . . . . . . . . . . . . . . .32

AUTOMATIC

TIMER RECORDING . . . . . . . . . .32

TIMER PROGRAM EXTENSION .33

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . .34

AUTO RETURN . . . . . . . . . . . . . . .34

SLEEP TIMER . . . . . . . . . . . . . . . .34

C ON SCREEN DISPLAY . . . . . . . . .35

C CABLE CHANNEL

DESIGNATIONS . . . . . . . . . . . . . .35

DVD SECTION

C ABOUT THE DISCS . . . . . . . . . . . .36

PLAYABLE DISCS . . . . . . . . . . . .36

DISC TYPES . . . . . . . . . . . . . . . . .36

C PLAYING A DISC . . . . . . . . . . . . . .37

BASIC PLAYBACK . . . . . . . . . . . .37

GENERAL FEATURES . . . . . . . . .37

DISC MENU . . . . . . . . . . . . . . . . .37

TITLE MENU . . . . . . . . . . . . . . . . .37

RESUME . . . . . . . . . . . . . . . . . . . .38

PAUSE . . . . . . . . . . . . . . . . . . . . . .38

STEP BY STEP PLAYBACK . . . . .38

FAST FORWARD/REVERSE

SEARCH . . . . . . . . . . . . . . . . . . . .38

SLOW FORWARD / SLOW

REVERSE . . . . . . . . . . . . . . . . . . . .38

C SEARCH FUNCTION . . . . . . . . . . .39

TRACK SEARCH . . . . . . . . . . . . .39

TITLE / CHAPTER SEARCH . . . .39

TIME SEARCH . . . . . . . . . . . . . . .39

MARKER SETUP SCREEN . . . . . .39

SPECIAL PLAYBACK FUNCTION . . .40

REPEAT . . . . . . . . . . . . . . . . . . . . .40

PROGRAM . . . . . . . . . . . . . . . . . . .40

RANDOM PLAYBACK . . . . . . . . .40

C PLAYING A MP3 DISC . . . . . . . . . .41

MP3 PLAYBACK . . . . . . . . . . . . . .41

REPEAT . . . . . . . . . . . . . . . . . . . . .41

PROGRAM . . . . . . . . . . . . . . . . . . .41

RANDOM PLAYBACK . . . . . . . . .41

C CHANGING THE SETTINGS . . . .42

SUBTITLE LANGUAGE . . . . . . . .42

AUDIO LANGUAGE . . . . . . . . . . .42

STEREO SOUND MODE . . . . . . . .42

CAMERA ANGLE . . . . . . . . . . . . .42

BLACK LEVEL SETTING . . . . . . .42

VIRTUAL SURROUND . . . . . . . . .42

THE ON-SCREEN INFORMATION . . .43

C CHANGING THE DVD SETUP

ITEMS . . . . . . . . . . . . . . . . . . . . . . .44

LANGUAGE SETTING . . . . . . . . .44

DISPLAY SETTING . . . . . . . . . . . .45

AUDIO SETTINGS . . . . . . . . . . . .45

PARENTAL CONTROL . . . . . . . . .46

INITIALIZE . . . . . . . . . . . . . . . . . .46

C TROUBLESHOOTING GUIDE . . .47

C MAINTENANCE . . . . . . . . . . . . . . .50

DISC HANDLING . . . . . . . . . . . . .50

C SPECIFICATIONS . . . . . . . . . . . . .51

C ESPAÑOL . . . . . . . . . . . . . . . . . . . .52

C WARRANTY . . . . . . . . . . .Back Cover

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 6

- 7 - EN

1C29

•

Hi-Fi system

–The Hi-Fi stereo recording system

offers you excellent sound quality with a dynamic

range of 80dB, frequency response from 20Hz to

20kHz and 0.005% wow and flutter.

•

Rotary 4-head Record/Playback System–Four heads

ensure excellent picture quality and special effects playback.

•

Index Search–

Fast-forwards to start of next recording.

•

Slow Motion–View recorded program at slower

than normal speed.

•

Infrared remote control

•

Trilingual on screen TV/VCR setup display

selectable in English, Spanish or French

•

Real time counter–This shows the elapsed recording

or playback time in hours, minutes and seconds.

The

“–” indication will appear when the tape is rewound

further than the tape counter position “0:00:00”.

•

181 channel capability PLL frequency synthesiz-

er tuner with direct station call–

(A converter may

be necessary to view scrambled cable channels.)

•

Auto Clock Setting–Allows you to set the clock

function from a PBS broadcast station.

•

Closed caption system–You may view specially

labeled (cc) TV programs, movies, news, prere-

corded tapes, etc. with either a dialogue caption or

text display added to the program.

•

Auto power on and off system–Automatically

turns on the unit when you insert the cassette, turns

off after auto-rewind and ejects when the begin-

ning of the tape is reached.

•

Auto rewind when the end of a tape is

reached–

This function doesn’t occur when using

timer recording.

•

Smooth mode change–TV/VCR mode DVD

mode automatically changes without control.

•

2 Step picture search operation–You can view a

video program at a high speed or super high speed

in either a forward or reverse direction in LP and

SLP mode. For SP mode only high speed.

•

Three different playback tape speeds : SP/LP/SLP

•

Two different recording tape speeds : SP/SLP

•

Auto Head Cleaner–Automatically cleans video

heads as you insert or remove a cassette.

•

Zero Return–The tape returns to counter of

0:00:00 by rewinding or fast forwarding.

•

Still–“Freeze” the picture at any time, for close

viewing of a particular scene.

•

Digital Auto Tracking (DTR)–Automatically

adjusts the tracking for each tape you play.

•

Rental play mode–Improves playback picture

quality from worn tapes, such as rental tapes.

•

Auto repeat–Allows you to repeat the playing of a

tape indefinitely without pressing the PLAY button.

•

Time search–Let you set the unit to advance the

tape by entering the desired playback time you want

to skip.

•

OTR (One Touch Recording)–Instant timed

recording from 30 to 480 minutes is possible at the

push of the REC/OTR button.

•

1 Year, 8 events (including Daily and Weekly

Timer Recording)–

The built-in timer allows you to

record up to 8 programs at different times on dif-

ferent channels up to 1 year in advance. The Daily

timer allows recordings to be made of daily broad-

casts and the Weekly timer allows recording to be

made once a week up to the end of the tape.

•

Auto return–After timer recording is finished, the

unit can return to the beginning of the recording.

•

Sleep timer–Allows you to have the unit automati-

cally turn off at a desired time.

•

Timer Program Extension–Allow you to shift the

time schedule for automatic timer recording.

•

V-CHIP–Enables parents to prevent their children

from watching inappropriate material on TV.

FEATURES

TV/VCR Mode

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 7

- 8 - EN

1C29

¡Dolby Digital sound

This unit can handle Dolby Digital surround sound

having 5.1 channels when connected to a Dolby

Digital decoder.

¡Still/fast/slow/step playback

Various playback modes are available including still

pictures, fast forward/reverse, slow motion and step

frames.

¡Random playback for Audio CD and MP3

This unit can shuffle the order of tracks to play them

in random order.

¡Program playback for Audio CD and MP3

You can program the order of tracks to play them in

any desired order.

¡DVD menus in a desired language

You can display DVD menus in a desired language,

if available on a DVD.

¡Screen saver/Auto power-off functions

The screen saver program starts when there is no input

from the unit for 5 minutes in the stop mode. When the

screen saver program is activated for 15 minutes, the

power automatically turns off.

¡Subtitles in a desired language

You can select a desired language for the display

subtitles, if that language is available on a disc.

¡Selecting a camera angle

You can select the desired camera angle, if a disc

contains sequences recorded from different angles.

¡Choices for audio language and sound mode

You can select the desired audio language and sound

mode, if different languages and modes are available

on a disc.

¡Parental lock

You can set the control level to limit playback of

discs which may not be suitable for children.

¡Automatic detection of discs

This unit automatically detects if the loaded disc is

DVD, Audio CD or MP3 on disc.

¡Playback MP3 disc

¡On-screen display

Information about the current operation can be dis-

played on a TV screen, allowing you to confirm the

currently active functions (such as program play-

back), on the TV screen using the remote control.

¡Search

Chapter search / Title search / Track search / Time

¡Repeat

Chapter / Title / Track / Group / All / A-B

¡Marker

The part designated by user can be called back.

¡Resume Play

User can resume to playback from the part at which

the play was stopped.

¡Virtual Surround

¡Bit rate indication

¡DRC (Dynamic range control)

You can control the range of sound volume.

NOTE:

•

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control.

If you decide to use a universal remote control with this unit, please be aware that the code number given

may not operate this unit. In this case, please call the manufacturer of the universal remote control.

DVD Mode

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 8

- 9 - EN

1C29

OPERATING CONTROLS AND FUNCTIONS

5.STOP Button

[TV/VCR P.26 / DVD P.37]

Stops operation of the disc. (front panel)

Stops operation of the disc or tape contents.

(remote control)

6.OPEN/CLOSE Button

[DVD P.37]

Press to insert discs into or remove them from the

tray.

7.Disc loading tray

8.DVD Indicator

Illuminates during DVD mode.

9.SELECT Button

Press to change to TV/VCR mode, external input

mode or DVD mode.

10.TV/VCR Indicator

Illuminates during TV/VCR mode.

11. CHANNEL (CH.) K/L Buttons

Press to select memorized channel.

12. Recording Indicator

Flashes during recording. Illuminates in the Stand-

by mode for Timer Recording.

13. REC/OTR Button (Front Panel)

[TV/VCR P.30, 31]

Press to start manual recording. Press repeatedly

to start One Touch Recording (only during

TV/VCR mode).

RECORD Button (Remote Control)

[TV/VCR P.30]

Press to start manual recording.

14. REW Button (for TV/VCR)

[TV/VCR P.26]

Press to rewind the tape, or to view the picture

rapidly in reverse during playback mode. (Rewind

Search)

15. F.FWD Button (for TV/VCR)

[TV/VCR P.26]

Press to rapidly advance the tape, or to view the

picture rapidly in forward during playback mode.

(Forward Search)

16. STOP/EJECT Button

[TV/VCR P.28]

Press to stop the tape motion. Press in the Stop

mode to remove tape from the unit.

17. Remote sensor window

18. HEADPHONE Jack

To connect headphone (not supplied) for personal

listening.

- REMOTE CONTROL -

[Fig. 2]

1.POWER Button

[TV/VCR P.15 / DVD P.37]

Press to turn the power on and off.

2.VOLUME (VOL.)

Buttons

Press to control the volume level for the DVD and TV.

3.SKIP/SEARCH Buttons (for DVD)

[P.38]

Press once to skip chapters or tracks to a desired

point.

Press and hold to change forward or reverse play-

back speed.

4.PLAY Button

[TV/VCR P.26 / DVD P.37]

Starts playback of the disc or tape contents.

- FRONT PANEL - [Fig.1]

1 4 5 6 10

1514983 3 411 12 13 2120191817162

DVD buttons

TV/VCR buttons

PAUSE

PLAY

STOP

ENTER

RECORD

DISC

RETURNTITLESETUP

REPEATSEARCH MODE

CLEAR

MODE

ANGLESUBTITLEAUDIO

DISPLAY

SPEED C.RESET

POWER PICTURE SELECTSLEEP

CH.

VOL.

MUTEV.SURR

123

456

789

0 +10

+100

(DVD) 3

(TV/VCR) 14

3 (DVD)

15 (TV/VCR)

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 9

- 10 - EN

1C29

ANT.

AUDIO OUT

COAXIAL

19. VIDEO input Jack

Connect to the video output jack of a video

camera or VCR.

20. AUDIO L/R input Jacks

Connect to the audio output jacks of a video

camera or VCR.

21. Cassette compartment

22. PICTURE Button

Press to adjust the picture.

23. Number Buttons

TV/VCR Mode:

[P.18]

Press two digits to directly access the desired

channel.

Remember to press a “0” before a single digit

channel.

+100 Button–

Press to select cable channels which are equal or

greater than number 100.

DVD Mode:

Press to enter the desired number.

+10 Button–

Press to enter the desired numbers which are

equal or greater than number 10.

24. PAUSE Button

[TV/VCR P.26 / DVD P.38]

Pauses the current disc or tape operation.

25. SPEED Button

[TV/VCR P.30]

Press to choose the desired recording speed: SP/SLP.

26. C.RESET Button

[TV/VCR P.28]

Press to reset counter to 0:00:00.

Press to cancel a setting of timer program.

(See page 33.)

27. DISPLAY Button

TV/VCR Mode:

Display the counter or the current channel number

and current time on the TV screen.

DVD Mode:

[P.43]

Displays the current status on the TV screen for

checking purposes.

28. SETUP Button

[TV/VCR P.15] [DVD P.44-46]

Press to enter or exit the TV menu or DVD setup

mode.

29. TITLE Button

[DVD P.37]

Displays the title menu.

30. CLEAR Button

Resets a setting.

31. MODE Button

[DVD P.40]

Activates program playback or random playback mode.

32. SEARCH MODE Button

[DVD P.39]

Press to locate a desired point.

33. AUDIO Button

[DVD P.42]

Press to select a desired audio language or sound

mode.

34. SUBTITLE Button

[DVD P.42]

Press to select a desired subtitle language.

35. REPEAT Button

[DVD P.40]

Repeats playback of the current disc, title, chapter,

group or track.

36. ANGLE Button (DVD mode)

[DVD P.42]

Press to change the camera angle to see the

sequence being played back from a different angle

if available.

37. A-B REPEAT Button

[DVD P.40]

Repeats playback of a selected section.

38. RETURN Button

Returns to the previous operation in the DVD

setup mode.

39. ENTER Button

Press to accept a setting.

40. Arrow Buttons

TV/VCR Mode:

Press to select a setting mode from the menu on

the TV screen.

Press to select or adjust from a particular menu.

DVD Mode:

Use when making settings while watching the

display on a TV screen.

41. DISC MENU Button

[DVD P.37]

Displays the menus in the DVD.

42. V. SURR (VIRTUAL SURROUND) Button

[DVD P.42]

Sets virtual surround on/off.

43. MUTE Button

Mutes the sound. Press it again to resume sound.

44. SLEEP Button

[TV/VCR P.34]

Sets the Sleep Timer.

- REAR PANEL - [Fig.3]

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 10

- 11 - EN

1C29

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown in the illustration.

By using this connection you can also record scram-

bled channels. However, channel selection must be

made with the converter box or satellite box. This

means that channels cannot be changed using the

remote control. Unattended timer recording is limited

to one channel at a time.

PREPARATION FOR USE

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects

directly to your unit without a converter box.

By using this connection you can:

1) Use the unit’s remote control to select channels.

2) Program one or more unscrambled channels for

Automatic Timer Recording.

NOTE: This unit will ONLY record and view the

same channel.

VHF/UHF SEPARATE ANTENNAS

In some areas it will be necessary to use an outdoor

antenna.

Antenna/Cable Connections

Continued on the Next Page.

ANT.

AUDIO OUT

COAXIAL

ANT.

OUT

VHF/UHF Antenna

(Not supplied)

VHF/UHF

Combiner

(Not supplied)

Flat twin-lead cable

UHF Antenna

(Not supplied)

VHF Antenna (Not supplied)

From Cable

System

75-ohm Coaxial

Cable (Not supplied)

75-ohm

Coaxial

Cable

(Not sup-

plied)

Satellite Box or

Cable Box (Not supplied)

From Cable System or

Satellite Dish

45. SELECT Button

Press to switch TV/VCR and DVD mode. You

can see the mode (TV/VCR or DVD) on the front

panel indicator.

46. ANT. in Jack

Connect to an antenna, cable system or satellite

system.

47. Power cord

Connect to a standard AC outlet (120V/60Hz).

NOTE: Remove the power cord from the hook to

avoid breaking a wire before you connect

to a standard AC outlet.

48. COAXIAL digital audio out Jack

Connect to the digital input of an external

amplifier or decoder (for DVD audio only).

[Fig. 4]

ANTENNA/CABLE CONNECTION

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 11

- 12 - EN

1C29

TO RECORD A SCRAMBLED/UNSCRAM-

BLED CHANNEL

1.Set the unit’s channel selector to the output channel

of the Cable Converter Box or Satellite Box (Ex.

CH3).

2.Select the channel to record from your Cable

Converter Box or Satellite Box.

INSTALLING THE BATTERIES

1)Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2)Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

3)Replace the cover.

EXTERNAL INPUT MODE

When using an external input signal (another VCR or

video camera), connect the player’s audio/video out-

put cables to the AUDIO L/R IN/

VIDEO IN jacks of your unit. Then

press the CHANNEL button K or

L until “AUX” appears on the

screen.

AUX

Note to CATV system installer:

This reminder is provided to call the CATV sys-

tem installer’s attention to Article 820-40 of the

NEC that provides guidelines for proper ground-

ing and in particular, specifies that the cable

ground shall be connected to the grounding sys-

tem of the building as close to the point of cable

entry as practical.

CONNECTING TO EXTERNAL

INPUT JACKS

When you watch a program recorded on another

source (VCR or video camera), use the AUDIO/

VIDEO input jacks on the front panel.

Connect the audio/video output jacks of another

source to the AUDIO L/R and VIDEO jacks of this

unit.

Then press the CHANNEL button

K or L until

“AUX” appears on the screen.

NOTE:

•

When you connect a monaural VCR (another

source) to this unit, connect the Audio output jack

of the monaural VCR (another source) to the

AUDIO L jack of this unit. The audio will output

in both L and R channel equally.

[Another source]

To the audio

output jacks

Audio/Video

cable

(not supplied)

etc.

To the video

output jack

[Front of the unit]

[Fig. 5]

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 12

- 13 - EN

1C29

CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH DIGI-

TAL INPUT JACKS SUCH AS MD DECK OR DAT DECK (for DVD)

Use an audio coaxial digital cable available at retail for the audio connections.

Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.

NOTES:

•

The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital

sound by an MD or DAT deck.

•

Be sure to turn off the power to all components in the system before connecting another component.

•

Refer to the Owner's Manuals for the components to be connected to the unit.

•

Set Dolby Digital to OFF for audio output in the setup mode. Playing a unit with incorrect settings may

generate noise distortion and may also damage the speakers.

ANT.

AUDIO OUT

COAXIAL

Amplifier equipped with digital

input jacks, MD deck,

DAT deck, etc.

To COAXIAL DIGITAL

AUDIO INPUT jack

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

(only DVD AUDIO OUT)

[Fig. 6]

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 13

- 14 - EN

1C29

ANT.

AUDIO OUT

COAXIAL

Front speaker

(left)

Center

speaker

Front speaker

(right)

Surround

speaker

(left)

Surround

speaker

(right)

Subwoofer

To DIGITAL AUDIO OUT

(PCM/BITSTREAM)

COAXIAL jack

To COAXIAL DIGITAL

AUDIO INPUT jack

Dolby Digital

decoder

[Fig. 7]

CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)

If you use this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, the unit outputs a

DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the unit up to a Dolby

Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround

sound as enjoyed in movie theaters.

Use audio coaxial digital cables available at retail for the audio connections.

NOTES:

•

Be sure to turn off the power to all components in the system before connecting another component.

•

Refer to the Owner's Manuals for the components to be connected to the unit.

•

If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.

(See page 45 to set DOLBY DIGITAL to ON.)

•

Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup

mode. Playing a unit with incorrect settings may generate noise distortion and may also damage the speak-

ers.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 14

- 15 - EN

1C29

SET UP FOR USE

TV/VCR SECTION

1 Plug in the power cord

Plug the unit’s power cord into a standard

AC outlet.

NOTE:

•

If any digits appear in the corner of the

screen, press the POWER button without unplug-

ging the power cord.

Make sure ...

•

Press the SELECT button to select TV/VCR mode

or make sure TV/VCR lights on.

•

Press the POWER button to turn on the unit.

NOTE:

This function effects only the language on the screen

menu and not the audio source.

2 Select “LANGUAGE”

Press the SETUP button on the

remote control.

Press the Arrow button

K or L to

point to “LANGUAGE”.

3 Select “ENGLISH”,“ESPAÑOL” or “FRANÇAIS”

Select “ENGLISH”, “ESPAÑOL”= Spanish or

“FRANÇAIS”= French using the ENTER button.

4 Exit the Language mode

Press the SETUP button on the remote control to

return to TV mode.

NOTE:

If for some reason the menu is in Spanish or French,

press the SETUP button on the remote control, press

the Arrow button K or L to point to “IDIOMA

[ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then

press the ENTER button, then press the SETUP but-

ton on the remote control.

SELECTING THE LANGUAGE

The unit’s clock must be set correctly before VCR

timer recording is possible. It is suggested that the

clock be set manually when first setting up the unit,

then set to [ON] the auto clock setting which will

periodically correct the setting if necessary.

NOTE:

If you cannot receive a station with time signals, the

auto clock setting cannot be performed. Use manual

setting only.

MANUAL CLOCK SETTING

Make sure ...

•

The unit is turned on.

In the example below, the clock is to be set to:

DATE May 6th, 2004

SETTING TIME 5:40PM

1 Select “SETTING CLOCK”

Press the SETUP button on the

remote control.

Press the Arrow button

K or L to

point to “SETTING CLOCK”.

Then press the ENTER button.

2 Select “MANUAL CLOCK SET”

Press the Arrow button K or L to

point to “MANUAL CLOCK

SET”.

Then press the ENTER button.

3 Select the month

Press the Arrow button K or L

until your desired month appears.

(Example: May → 05)

Then press the Arrow button

(or press the Arrow button { to

go back one step).

4 Select the day

Press the Arrow button K or L

until your desired day appears.

(Example: 6th → 06)

Then press the Arrow button

CLOCK SET UP

(AUTO / MANUAL)

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5 / – – – – – – – – –

HOUR MINUTE

– – : – – – –

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5 / 0 6 – – – – – – –

HOUR MINUTE

– – : – – – –

– SETTING CLOCK –

AUTO CLOCK [ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH [ 02 ]

B MANUAL CLOCK SET

D.S.T. [OFF]

TV/VCR

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

B LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

- TV/VCR SETUP -

TIMER PROGRAMMING

B SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 15

- 16 - EN

1C29

5 Select the year

Press the Arrow button K or L

until your desired year appears.

(Example: 2004)

Then press the Arrow button

6 Select the hour

Press the Arrow button K or L

until your desired hour appears.

(Example: 5, PM)

Then press the Arrow button

7 Select the minute

Press the Arrow button K or L

until the desired minute appears.

(Example: 40)

8 Start the clock

Press the SETUP button on the

remote control.

Although seconds are not dis-

played, they begin counting from

00 when you press the SETUP but-

ton on the remote control. Use this

feature to synchronize the clock with the correct

time.

NOTE:

When unplugging the AC cord or if there is a power

failure for more than 3 seconds, you may have to

reset the clock.

TO CHANGE CLOCK SETTING

If you want to change the clock,

1)Follow the steps [1] to [2].

2)Select where you want to change using the Arrow

button

3)Enter correct numbers using the Arrow button

or L.

4)Press the SETUP button on the remote control to

start the clock.

PLEASE NOTE:

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and

press the ENTER button to turn [OFF] this function.

Then you can manually adjust the clock.

AUTOMATIC CLOCK SETTING

Make sure ...

•

The unit is turned on.

•

Confirm the unit is receiving a RF (Radio

Frequency) signal from either an antenna or cable

system connection using the ANT. jack on the rear

panel.

NOTE:

•

If a cable converter box is being used, make sure it

is powered on.

•

You must use the unit’s remote control to perform

the clock setting procedure.

•

If the unit is connected directly to a cable converter

box or satellite box, the local PBS station must be

selected on the cable box itself and the unit must

be set to the output channel of the cable converter

box or satellite box (usually channel 3 or 4), to be

able to set up or correct the clock automatically.

1 Select “SETTING CLOCK”

Press the SETUP button on the

remote control.

Press the Arrow button

K or L to

select “SETTING CLOCK”.

Press the ENTER button to enter

“SETTING CLOCK” menu.

2 Set “AUTO CLOCK” to [ON]

Press the ENTER button until

“AUTO CLOCK [ON]” appears.

3 Begin “AUTO CLOCK CH SEARCH”

Press the Arrow button L to select

“AUTO CLOCK CH SEARCH”.

Press the ENTER button.

•

The unit is now searching for the

station which contain the auto

clock set signal. The search for a

signal may take up to 20 seconds

per channel.

•

“_ _” appears at the lower left of

the screen when the search has

ended.

•

Auto Clock station- write down

the number(s) that appear on the

screen. These are the auto clock

station(s) in your area. See step [4] on page 17.

•

If no number(s) appear on the TV screen, there are

no stations in your area which contain the Auto

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on page 15.

Press the SETUP button to exit the screen.

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5 / 0 6 THU 2 0 0 4

HOUR MINUTE

0 5 : – – PM

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5 / 0 6 THU 2 0 0 4

HOUR MINUTE

0 5 : 4 0 PM

5:40 PM

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5 / 0 6 THU 2 0 0 4

HOUR MINUTE

– – : – – – –

– SETTING CLOCK –

B AUTO CLOCK [ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH [ 02 ]

MANUAL CLOCK SET

D.S.T. [OFF]

– SETTING CLOCK –

AUTO CLOCK [ON]

B AUTO CLOCK CH SEARCH

AUTO CLOCK CH [ 02 ]

MANUAL CLOCK SET

D.S.T. [OFF]

– AUTO CLOCK CH SEARCH –

08 10 13

_ _

- TV/VCR SETUP -

TIMER PROGRAMMING

B SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 16

- 17 - EN

1C29

DAYLIGHT-SAVING TIME

Select this feature and the unit’s clock automatically

will advance one hour in April, then reverse one hour

in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

•

First Sunday of April : At 2 AM the clock imme-

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

•

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

Make sure ...

•

Press the POWER button to turn on the unit.

1 Select “SETTING CLOCK”

Press the SETUP button on the

remote control.

Press the Arrow button

K or L to

point to “SETTING CLOCK”.

Then press the ENTER button.

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press the Arrow button K or L to

point to “D.S.T.”.

Then press the ENTER button until

[ON] appears.

3 Exit the Daylight-Saving Time mode

Press the SETUP button on the remote control to

return to TV mode.

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps [1] to [2] and select [OFF] using the

ENTER button.

– SETTING CLOCK –

AUTO CLOCK [ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH [ 02 ]

MANUAL CLOCK SET

B D.S.T. [ON]

NOTE: During Auto Clock CH Search, the picture

may be distorted, this is normal.

4 Enter the channel number that contains the

Automatic Clock Setting Signal

Press the SETUP button on the remote control.

Press the Arrow button

K or L to

select “SETTING CLOCK”.

Press the ENTER button to enter

“SETTING CLOCK” menu.

Press the Arrow button

L to select

“AUTO CLOCK CH”.

Press the ENTER button or the

Arrow button

{ or B until you

locate Auto Clock Set station num-

ber. See step [3] on page 16.

Press the SETUP button to exit the

screen.

5 Turn off the unit

Once the unit is turned off, it will periodically check

and set the correct date and time.

– SETTING CLOCK –

AUTO CLOCK [ON]

AUTO CLOCK CH SEARCH

B AUTO CLOCK CH [ 45]

MANUAL CLOCK SET

D.S.T. [OFF]

TV/VCR

- TV/VCR SETUP -

TIMER PROGRAMMING

B SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

- TV/VCR SETUP -

TIMER PROGRAMMING

B SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 17

- 18 - EN

1C29

CHANNEL SET UP

Make sure ...

•

Press the POWER button to turn on the unit.

1 Select “CHANNEL SET UP”

Press the SETUP button on the

remote control.

Press the Arrow button

K or L to

point to “CHANNEL SET UP”.

Then press the ENTER button.

2 Begin auto ch programming

Press the Arrow button K or L to

point to “AUTO CH PROGRAM-

MING”.

Then press the ENTER button.

The tuner scans and memorizes all

the active channels in your area.

3 After scanning

The tuner stops on the lowest memorized channel.

•

When AUTO CH PROGRAMMING is activated

where there is no TV signal input, “NO TV SIG-

NALS” will appear on the display after the com-

pletion of the channel scanning.

•

The unit may recognize TV channels to be CATV

channels by the receiving conditions. In this case,

try AUTO CH PROGRAMMING again in the fine

receiving conditions.

– CHANNEL SET UP –

ADD / DELETE CH (CATV)

B AUTO CH PROGRAMMING

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you

can add the deleted channel into the memory again.)

1 Select “CHANNEL SET UP”

Press the SETUP button on the

remote control.

Press the Arrow button

K or L to

point to “CHANNEL SET UP”.

Then press the ENTER button.

2 Select “ADD/DELETE CH”

Press the Arrow button K or L to

point to “ADD/DELETE CH”.

Press the ENTER button.

3 Enter the desired channel number

Press the Arrow button K or L

until your desired channel number

appears. (You can also use the

number buttons or the CHANNEL

button K or L to enter it)

(Example: CH8)

•

You must precede single-digit channel numbers

with a zero (Example: 02 ... 09).

•

When selecting cable channels which are higher

than 99, press the +100 button first, then, press the

last two digits. (Example: to select channel 125,

first press the +100 button then press “2” and “5”).

4 Delete (or add) it from (or into) memory

Press the ENTER button. The channel number

changes to light red. The channel is deleted from

memory.

•

To delete another channel, repeat steps [3] to [4].

•

If you press the ENTER button again, the channel

is memorized again.

5 Exit the channel setup mode

Press the SETUP button on the remote control to

return to TV mode.

NOTE:

To confirm that channel(s) has been deleted or

added, press the CHANNEL button K or L.

DELETING (OR ADDING)

CHANNEL(S)

Added channel: Light blue

Deleted channel: Light red

– CHANNEL SET UP –

B ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

ADD / DELETE

You can program the tuner to scan all the channels

you receive in your area.

NOTE:

Channel memory programming is NOT needed when

connected to a cable box or satellite box. Just select

the unit’s channel selector to the output channel of

the cable box or satellite box (Ex CH3), then select

the channel to be viewed on the Cable Box or

Satellite Box.

TV/VCR

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

B CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

B CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 18

- 19 - EN

1C29

TV OPERATION

DEGAUSSING

Magnetism from nearby appliances and speakers

might affect the color of the TV picture.

If this happens, move this unit away from the appli-

ance. If the color is still not correct, unplug the

power cord, then plug it in again 30 minutes later or

so.

TV/VCR

WATCHING A TV PROGRAM

1 Turn on the unit

Press the POWER button to turn on the unit.

2 Select the channel number

Press the CHANNEL button K or L to select your

desired channel number or press the number on the

remote control.

Note for using the Number button on the remote

control:

¡You must precede single-digit channel numbers

with a zero (For example: 02, 03, 04 and so on).

¡When selecting cable channels which are higher

than 99, press +100 first, then, press the last two

digits. (Example: to select channel 125, first press

“+100” then press “2” and “5”).

Remember: If the unit is connected to a cable box or

satellite box, the unit must be on CH3 or CH4, then

the channel to be viewed must be selected on the

cable box or satellite box.

3 Adjust sound

Press the VOLUME button X or Y

to adjust the volume.

NOTES:

•

If you press the CHANNEL button K or L in the

DVD mode, you can change the TV channels.

Even if you turn off the unit in the DVD mode, it

will go into the TV/VCR mode when you turn it on

again.

TV/VCR

PICTURE CONTROL

The unit’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a more natural looking image.

NOTES:

•

Procedures must be followed within 5 seconds or

the Picture Control mode will be cancelled.

Make sure ...

•

The unit must be turned on.

1 Select “PICTURE CONTROL”

Press the PICTURE button on the remote control.

2 Select item you want to adjust

Press the Arrow button K or L until desired control

is displayed.

BRIGHT

CONTRAST

COLOR

TINT

SHARPNESS

3 Adjust the picture control

Press the Arrow button { or B to adjust to your

desired level.

•

If there is a power failure of any kind, the unit

will retain its memory for this feature.

TV/VCR

VOLUME 20

C C C C C C C C C C C C

BRIGHT

–

PP PP PP PP PP PP PP CC PP PP PP PP PP PP PP

Arrow button s Arrow button B

BRIGHT to decrease to increase

brightness brightness

CONTRAST to decrease to increase

contrast contrast

COLOR to pale to brilliant

TINT to purple to green

SHARPNESS to soft to clear

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 19

- 20 - EN

1C29

CLOSED CAPTION SYSTEM

You can view specially labeled (cc) TV programs,

movies, news and pre-recorded tapes with either a

dialogue caption or text display.

CAPTION mode: By choosing the caption mode, you

can watch dramas, movies and news while captioning

the dialogues and the contents of news.

TEXT mode: By choosing the text mode, you can

watch half screen text information if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is used,

usually for a second language if available.

NOTE:

Not all programs are broadcast with closed captions.

Your unit is designed to provide error free closed

captions from high quality antenna, cable and VCR

signals. Conversely, poor quality signals are likely to

result in caption errors or no captions at all. Common

signal conditions which may cause caption errors are

listed below:

•

Automobile ignition noise

•

Electric motor brush noise

•

Weak snowy reception on TV screen

•

Multiplex signal reception displaying picture

ghosts or airplane flutter.

•

Playback of poorly recorded or worn VCR tapes.

NOTE:

If the unit displays a black box on

the TV screen, this means that the

unit is set to the TEXT mode. To

clear screen, select [CAPTION1],

[CAPTION2] or [OFF].

Make sure ...

•

The unit is turned on.

TV/VCR

1 Select “CAPTION”

Press the SETUP button on the

remote control.

Press the Arrow button

K or L to

point to “CAPTION”.

2 Select your desired caption menu

Press the ENTER button until your

desired caption menu appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

3 Exit the caption setting mode

Press the SETUP button on the remote control to

return to TV mode.

TO CANCEL THE CLOSED CAPTION

SYSTEM

Repeat steps [1] to [2] and select [OFF] using the

ENTER button. Press the SETUP button on the

remote control to return to TV mode.

WHEN THE CLOSED CAPTION MODE

IS ON

The On-Screen Display will disappear after 5 sec-

onds.

•

It will also disappear when the MUTE button or

the PAUSE button is pressed while recording.

•

If there is a power failure of any kind, the unit will

retain its memory for this feature.

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

B CAPTION [OFF]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

- TV/VCR SETUP -

TIMER PROGRAMMING

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

B CAPTION [CAPTION1]

ZERO RETURN

TIME SEARCH

INDEX SEARCH

T0052UC(p1-35).QX3 04.9.16 2:13 PM Page 20

Page is loading ...

Emerson EWC19T4 User manual

Brand: Emerson

Model: EWC19T4

Category: CRT TVs

Type: User manual

Download PDF

report

Emerson EWC19T4 User manual

Emerson EWC19T4 User manual

Related papers

Other documents