Hitachi ED-X8250 series User manual

Brand: Hitachi

Model: ED-X8250 series

Category: Projectors

Type: User manual

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.

Multimedia LCD Projector

November 2005 Digital Media Division

SM0560

CP-S245(CC9SMN)

CP-X255(CC9XMN)

SERVICE MANUAL

Be sure to read this manual before servicing. To assure safety from ﬁ re, electric shock, injury, harmful

radiation and materials, various measures are provided in this Hitachi Multimedia LCD Projector. Be

sure to read cautionary items described in the manual to maintain safety before servicing.

Caution

1. When replace the lamp, to avoid burns to your ﬁ ngers. The lamp becomes too hot.

2. Never touch the lamp bulb with a ﬁ nger or anything else. Never drop it or give it a shock. They may

cause bursting of the bulb.

3. This projector is provided with a high voltage circuit for the lamp. Do not touch the electric parts of

power unit (circuit) and power unit (ballast), after turn on the projector.

4. Do not touch the exhaust fan, during operation.

5. The LCD module assembly is likely to be damaged. If replacing to the LCD LENS/PRISM assembly,

do not hold the FPC of the LCD module assembly.

6. Use the cables which are included with the projector or speciﬁ ed.

Service Warning

Warning

The technical information and parts shown in this

manual are not to be used for: the development,

design, production, storage or use of nuclear, chemical,

biological or missile weapons or other weapons of

mass destruction; or military purposes; or purposes that

endanger global safety and peace. Moreover, do not

sell, give, or export these items, or grant permission for

use to parties with such objectives. Forward all inquiries

to Hitachi Ltd.

1. Features -----------------------------------------------2

2. Speciﬁ cations -----------------------------------------2

3. Names of each part ---------------------------------3

4. Adjustment -------------------------------------------- 6

5. Troubleshooting ------------------------------------ 12

6. Service points -------------------------------------- 18

7. Wiring diagram ------------------------------------- 33

8. Disassembly diagram ----------------------------- 41

9. Replacement parts list ---------------------------- 48

10.RS-232C commands ----------------------------- 50

11. Block diagram -------------------------------------- 59

12. Connector connection diagram ---------------- 60

13.Basic circuit diagram ------------------------------ 61

Contents

ED-X8255(CC9XMN)

PJ656(CC9XM)

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)

1. Features

• High Brightness

• Low Noise

• Rich Connectivity

• Compact Body

2. Specifications

CP-S245CP-X255 / ED-X8255

Liquid crystal

panel

Drive system TFT active matrix

Panel size 1.5cm(0.6 type)

Number of pixels 800 (H) x 600 (V) 1024 (H) x 768 (V)

Lamp 180W UHB

RGB

signal

RGB IN

Video : Analog 0.7Vp-p(75Ω termination)

H/V. sync. : TTL level (positive/negative)

Composite sync. : TTL level

RGB OUT*

Video:Analog 0.7Vp-p, 75Ω output impedance (positive)

H/V. sync.: TTL level (positive/negative)

Composite sync.: TTL level

VIDEO

signal

VIDEO IN 1.0Vp-p (75Ω termination)

S-VIDEO IN

Y signal: 1.0±0.1Vp-p, (75Ω termination)

C signal: 0.286±0.1Vp-p (NTSC burst signal, 75Ω termination)

0.3±0.1Vp-p (PAL/SECAM burst signal, 75Ω termination)

COMPONENT

VIDEO

Y 1.0±0.1Vp-p, 75Ω termination (positive)

0.7±0.1Vp-p, 75Ω termination (positive)

AUDIO

signal

AUDIO IN 1 200mVrms, 47kΩ or more (max. 3.0Vp-p)

AUDIO IN 2 L/R 200mVrms, 47kΩ or more (max. 3.0Vp-p)

AUDIO OUT 0~200mVrms, output impedance 1kΩ (max. 5.0Vp-p)

Speaker output 1W x 1

Power supply AC100~120V/3.1A, AC220~240V/1.7A

Power consumption 290W

Dimensions 306 (W) x 86 (H) x 249 (D) mm (Not including protruding parts)

Weight 3.0kg

Temperature range

Operation : 5~35°C

Storage : -20~60°C

Accessories

Remote control x1

RGB cable x 1

Audio/Video cable x 1

Power cords x 3

Batteries x 2

User’s manuals x 1

Soft case x 1 (not ED-X8255)

*) This port is used as both RGB IN 2 and RGB OUT. Its function is selected with RGB IN/OUT switch.

PJ656(CC9XM)

1. Features

• High Brightness

• Low Noise

• Rich Connectivity

• Compact Body

2. Specifications

Liquid crystal

panel

Drive system TFT active matrix

Panel size 1.5cm(0.6 type)

Number of pixels 1024 (H) x 768 (V)

Lamp 180W UHB

RGB

signal

RGB IN

Video : Analog 0.7Vp-p(75Ω termination)

H/V. sync. : TTL level (positive/negative)

Composite sync. : TTL level

RGB OUT*

Video:Analog 0.7Vp-p, 75Ω output impedance (positive)

H/V. sync.: TTL level (positive/negative)

Composite sync.: TTL level

VIDEO

signal

VIDEO IN 1.0Vp-p (75Ω termination)

S-VIDEO IN

Y signal: 1.0±0.1Vp-p, (75Ω termination)

C signal: 0.286±0.1Vp-p (NTSC burst signal, 75Ω termination)

0.3±0.1Vp-p (PAL/SECAM burst signal, 75Ω termination)

COMPONENT

VIDEO

Y 1.0±0.1Vp-p, 75Ω termination (positive)

0.7±0.1Vp-p, 75Ω termination (positive)

AUDIO

signal

AUDIO IN 1 200mVrms, 47kΩ or more (max. 3.0Vp-p)

AUDIO IN 2 L/R 200mVrms, 47kΩ or more (max. 3.0Vp-p)

AUDIO OUT 0~200mVrms, output impedance 1kΩ (max. 5.0Vp-p)

Speaker output 1W x 1

Power supply AC100~120V/3.1A, AC220~240V/1.7A

Power consumption 290W

Dimensions 306 (W) x 83 (H) x 249 (D) mm (Not including protruding parts)

Weight 2.8kg

Temperature range

Operation : 5~35°C

Storage : -20~60°C

Accessories

Remote control x1

RGB cable x 1

Audio/Video cable x 1

Power cords x 3

Batteries x 2

User’s manuals x 1

Soft case x 1

*) This port is used as both RGB IN 2 and RGB OUT. Its function is selected with RGB IN/OUT switch.

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

3. Names of each part

Projector

●

WARNING

During use or immediately after use, do not touch around the lamp and vents of the pro-

jector. (

) It could cause a burn.

Lens

Filter cover

(Air ﬁlter and intake vent

are inside.)

Elevator button

Elevator foot

Remote sensor

Zoom ring

Focus ring

Vent

Lamp cover

(Lamp unit is inside.)

Bottom side

Speaker

Lens cover

Security bar

(Use for attaching a

commercial anti-theft

chain or wire.)

Control buttons



Front-Right side

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2

USB

RGB OUT

AUDIO IN1

LAN

LINK

ACT

VIDEO

S-VIDEO

AC inlet

Power switch

Elevator button

COMPONENT

VIDEO ports

S-VIDEO port

VIDEO port

CONTROL port

Elevator foot

Rear-Left side

Ports (See below.)

Vent

AUDIO-OUT port

Ports

AUDIO IN1 port

(In the default setting, the AUDIO

IN1 port is the audio port for the

RGB IN1 and RGB IN2 ports,

however, it is possible to change

the settings.)

AUDIO IN2 L/R port

(In the default setting, the

AUDIO IN2 L/R port is the audio

port for the VIDEO, S-VIDEO

and COMPONENT VIDEO

ports, however it is possible to

change the settings.)

RGB IN1 port

RGB IN2 /RGB OUT port

(Use the RGB IN OUT switch to select

RGB IN2 or RGB OUT for this port.)

RGB IN2 port: Inputs the RGB signal from

a PC.

RGB OUT port: When connected to a

monitor, outputs the signal input via RGB

IN1.

NOTE (*) About Restart switch: This projector is controlled by an internal

microprocessor. Under certain exceptional circumstances, the projector may not

operate correctly and the microprocessor will need to be reset. In such a case,

please push the Restart switch by using a cocktail stick or similar, and before

turning on again, make the projector cool down at least 10 minutes without

operating. Only push the Restart switch in these exceptional instances.

Restart switch (*)

RGB IN OUT switch

Use this button to select either RGB IN2

or RGB OUT for the corresponding port.

When this switch is not pushed in, RGB

IN2 is selected.

When this switch is pushed in, RGB OUT

is selected.

USB port

LAN Port

Used for Ethernet input/output.

This port is used when utilizing network functions.

PJ656(CC9XM)

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2

USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

AC inlet

Power switch

Elevator button

COMPONENT

VIDEO ports

S-VIDEO port

VIDEO port

CONTROL port

Elevator foot

Rear-Left side

Ports (See below.)

Vent

AUDIO-OUT port

Ports

AUDIO IN1 port

(In the default setting, the AUDIO

IN1 port is the audio port for the

RGB IN1 and RGB IN2 ports,

however, it is possible to change

the settings.)

AUDIO IN2 L/R port

(In the default setting, the

AUDIO IN2 L/R port is the audio

port for the VIDEO, S-VIDEO

and COMPONENT VIDEO

ports, however it is possible to

change the settings.)

RGB IN1 port

RGB IN2 /RGB OUT port

(Use the RGB IN OUT switch to select

RGB IN2 or RGB OUT for this port.)

RGB IN2 port: Inputs the RGB signal from

a PC.

RGB OUT port: When connected to a

monitor, outputs the signal input via RGB

IN1.

NOTE (*) About Restart switch: This projector is controlled by an internal

microprocessor. Under certain exceptional circumstances, the projector may not

operate correctly and the microprocessor will need to be reset. In such a case,

please push the Restart switch by using a cocktail stick or similar, and before

turning on again, make the projector cool down at least 10 minutes without

operating. Only push the Restart switch in these exceptional instances.

Restart switch (*)

RGB IN OUT switch

Use this button to select either RGB IN2

or RGB OUT for the corresponding port.

When this switch is not pushed in, RGB

IN2 is selected.

When this switch is pushed in, RGB OUT

is selected.

USB port

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

SEARCH button

RGB button

VIDEO button

ASPECT button

HOME button

MAGNIFY

ON button

OFF button

END button

FREEZE button

POSITION button

ESC button

Remote control

Battery cover

(on the back)

STANDBY/ON button

AUTO button

BLANK button

PAGE UP button

VOLUME button

MUTE button

PAGE DOWN button

KEYSTONE button

MENU button

Cursor buttons

▲,▼,◄,►

ENTER button

RESET button

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RGB

FREEZE

OFF

MAGNIFY

ASPECT AUTO

BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ESC

ENTER

RESET

Control buttons

LAMP indicator

TEMP indicator

POWER indicator

Cursor buttons

▲,▼,◄,►

STANDBY/ON button

INPUT button

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

4. Adjustment

4-1 Before adjusting

4-1-1 Selection of adjustment

When any parts in the table 4-1 are changed, choose the proper adjusting items with the chart.

Table 4-1: Relation between the replaced part and adjustment

Replaced

part

Adjustment

Convergence

(Chap.4-2)

Ghost

(Chap.4-3)

Flicker

(Chap.4-4)

White

balance

(Chap.4-5)

Color

uniformity

(Chap.4-6)

Dichroic

optics unit

LCD/LENS

prism

assembly

PWB

assembly

Main

Lamp

unit

assembly

: means need for adjustment.

: means not need for djustment.

: means recommended.

4-1-2 Setting of condition before adjustment

1. Before starting adjustment, warm up projector

for about 10 minutes.

2. Set Zoom Wide to Max. And project an image

with more than 1m (40 inches) in diagonal size.

3. Normalizing the video adjustment

Press the [MENU] button to display the Easy

menu. If Advance menu comes up, move to the

Easy menu.

Select RESET in the Easy menu and press [

]

or [ENTER] button to open the RESET menu

window. Choose EXECUTE with [ ] button.

Note that no signal input may not allow to reset

the adjustments.

4. Select PICTURE > GAMMA in the Advance

menu to set to DEFAULT1.

Note that PICTURE menu is not selectable with

no signal input displayed.

5. Select PICTURE > COLOR TEMP > CUSTOM

in the Advance menu, then press [

] or [ENTER]

button to display the equalizing window. Set all

the values of OFFSET and GAIN in the window

to zero.

Caution: Before this performance, make a note

of your customer’s adjustments, because the

data is overwritten.

6. Perform all adjustments from the FACTORY

MENU.

Perform the following operations to display the

FACTORY MENU.

< When you use the remote control… >

a. Press the [MENU] button of remote control to

display the Easy menu. (If the Advance menu

appears, move to the Easy menu from EASY

MENU.)

b. Select the [RESET] in the Easy menu, and

then press the [ ] or [ENTER] button.

c. Next, press the [RESET] button one time.

And hold the [RESET] button for 3 seconds

or more (the FACTORY MENU will appear).

< When you use the keypad… >

a. Press the [ ]

[ ]

[ ] button of the projec-

tor to display the Easy menu. (If the Advance

menu appears, move to the Easy menu from

EASY MENU.)

b. Select the [

RESET

] in the Easy menu, and

then press the [ ] button.

c. Next, press the [

] button one time. And

repress and hold the [ ] button together

with the [INPUT] button for 3 seconds or

more (the FACTORY MENU will appear).

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

4-3 Ghost adjustment

Signals for internal adjustment

30%

112/255

30%

0/255

Adjustment procedure

1. Make this adjustment after completing the

adjustment in 4-2.

2. Choose Advance menu > OPTION > SERVICE

> GHOST > R,G and B, and set them to zero.

3. Open the FACTORY MENU and choose DAC-P

> GHOST > R,G and B to display each color of

test patterns for adjustments.

Confirm if there is ghosting on the both sides of

black pattern. If visible, perform this adjustment

as following procedure.

Use DAC-P - GHOST - R: in the FACTORY MENU

to adjust so that R color ghost is at a minimum.

(Set the adjustment value to default, and then

raise the value. When a ghost appears to the left

of a vertical line, reduce the value by 3 steps.

Then, if a ghost image is visible on the right of

an original image, raise the number by 1 step.)

5. In the same way, use DAC-P - GHOST-G: in

the FACTORY MENU to adjust so that G color

ghost is at a minimum.

6. In the same way, use DAC-P - GHOST-B: in

the FACTORY MENU to adjust so that B color

ghost is at a minimum.

4-2 Convergence adjustment

Signal pattern for internal adjustment

Adjustment procedure

Perform this adjustments only when the conver-

gence is not good.

1. Open FACTORY MENU and then select

OPTION > CNV-V. Use R and/or B so that

three colors of images can be converged at

center, top and bottom of the screen.

2. In the same way, select OPTION > CNV-H and

use R and/or B so that three colors of images

can be converged at center, left and right of the

screen.

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

4-4 Flicker adjustment

(V.COM adjustment)

Signals for internal adjustment

Adjustment procedure

1. Make this adjustment after completing the

adjustment in 4-3 Ghost adjustment.

Use DAC-P - V.COM - R: in the FACTORY

MENU to adjust so that the flicker at the center of

the screen is less than the flicker at the periphery.

(When the flicker is about the same across the

whole screen, adjust so that the flicker at the center

of the screen is somewhat less than elsewhere.)

3. In the same way, use DAC-P - V.COM-G: in the

FACTORY MENU to adjust the G color flicker.

4. In the same way, use DAC-P - V.COM-B: in the

FACTORY MENU to adjust the B color flicker.

4-5

White balance adjustment

(visual inspection)

Preparations

1. Perform these adjustments after the Flicker

adjustment described in Section 4-4.

2. Reset gamma correction before adjustment.

Place the cursor on [GAMMA] in the FACTORY

MENU, press the [RESET] key and select RESET.

Adjustment procedure

1. First, adjust the G color.

Select GAMMA, SUB-CNT, and G: in the FACTORY

MENU. If the background is white solid, press the

[ENTER] key on the remote control to change to [G]

monochrome in the 33-tone grayscale.

3. Adjust GAMMA, SUB-CNT, and G: in the FAC-

TORY MENU so that brightness of 33 steps is

best.

4. Don’t adjust GAMMA, SUB-BRT, and G: in the

FACTORY MENU because we want to keep the

best contrast ratio.

5. Then adjust colors R and B.

Select GAMMA, SUB-CNT, and G: in the FACTORY

MENU. If the background is white solid, press the

[ENTER] key on the remote control to change to [W]

monochrome in the 33-tone grayscale.

7. Adjust GAMMA, SUB-BRT, R: and B: in the

FACTORY MENU so that low-brightness white

balance is best.

8. Adjust GAMMA, SUB-CNT, R: and B: in the

FACTORY MENU so that middle-brightness

white balance is best.

9. Repeat steps 7 to 8 above, and adjust so that

brightness white balance of 33 steps is best.

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

VID-AD

MIN

MID-L

MID-H

MAX

DAC-P

GAMMA

C. UNIF.

No. 1 R 0

STRIPE

OPTION

C.UNIF

ON/OFF ON

OFF

G 0 B 0

Major adjustment lattice point No.

4-6 Color uniformity adjustment

Preparations

Perform these adjustments after the white balance

adjustment described in Section 4-5.

2. Make a color uniformity adjustment for the follow-

ing four tones.

MIN tone (approx. 7% input signal)

MID-L tone (approx. 14% input signal)

MID-H tone (approx. 46% input signal)

MAX tone (approx. 70% input signal)

3. Place the cursor on [C.UNIF.] in the FACTORY

MENU and press the [ ] key. This displays the

Adjust Tone menu at the bottom of the screen.

To choose the tone to be adjusted, press the [ ]

key and then use the [ ] or [ ] key.

Select the major adjustment lattice point No.

and color, and then adjust them.

4. The major adjustment lattice point numbers (a

total of 17 points) corresponds to the major

adjustment lattice point positions in the diagram

on the right. The color uniformity of the entire

screen can be adjusted by adjusting the white

balance for each of the points starting in order

from the low numbers.

5. Adjustment point No.1 should not be adjusted,

because it controls the brightness of the entire

screen.

To temporarily turn correction off, place the

cursor on [C.UNIF.] in the Adjust Tone menu and

press the [

] key. The ON/OFF menu appears.

Place the cursor on [ON] with the [ ] key and

press the [ ] key. To turn it on again, place the

cursor on [OFF] and press the [ ] key.

7. Although this adjustment can also be made

using internal signals, we will here use the

[ENTER] key on the remote control to select the

following two signals.

Solid monochrome adjustment color (use G

color adjustment when a color differential

meter is used).

Solid white (use for adjustment other than

above).

8. Reset color-shading correction before adjust-

ment.

When 4 tones and all colors are to be reset,

place the cursor on [C.UNIF.] in the FACTORY

MENU, press the [RESET] key and select

RESET.

When only 1 tone is to be reset, place the

cursor on the tone to be reset, press the

[RESET] key and select RESET.

Single tone and monochrome resets cannot

be performed.

FACTORY MENU

Major adjustment lattice point position

14 12

15 17

6 4 8

2 1 3

7 5 9

10 11

V/6

H/6 H/3 H/3 H/6

V/3

V/6

Adjust tone menu

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

Adjustment procedure 1

(When a color differential meter is used)

1. First adjust [MID-L] tone [G:].

2. Select adjustment point [No.2][G:].

When the background is not [G] monochrome,

press the [ENTER] key on the remote control to

change to solid [G] monochrome.

3. Measure the illumination at adjustment points

No. 2, No.3, No.10 and No.11.

The values should be:

No.2 = Y2 [lx] No.10 = Y10 [lx]

No.3 = Y3 [lx] No.11 = Y11 [lx]

4. No.2 and No.3 adjustment point have the aver-

age of Y2 and Y3.

Y2 = ( Y2 + Y3 ) / 2 ± 2 [%]

Y3 = ( Y2 + Y3 ) / 2 ± 2 [%]

5. No.10 and No.11 adjustment point have the

average of Y10 and Y11.

Y10 = ( Y10 + Y11 ) / 2 ± 2 [%]

Y11 = ( Y10 + Y11 ) / 2 ± 2 [%]

6. Then adjust [MID-L] tone [R] and [B].

When the background is [G] monochrome,

press the [ENTER] key on the remote control to

change to solid white.

7. Measure the color coordinates of adjustment

point [No.1] and make a note of them.

Assume that they are x = x1, y = y1.

Note: When the CL-100 color and color differ-

ence meter is used, the [∆](delta) mode

is convenient. When adjustment point

[No.1] color coordinate has been

selected, set the slide switch on the side

to [∆](delta) while holding down the [F]

button on the front panel. The measure-

ment shown after this displays the devia-

tion from measurement point 1.

8. Measure the color coordinates of measurement

point [No.2] and adjust [No.2][R:] and [B:] so

that the coordinates are as follows.

x = x1 ± 0.005 , y = y1 ± 0.010

9. Similarly, measure adjustment points [No.3] to

[No.17] and adjust their color coordinates start-

ing in order from the small number points.

This completes adjustments required for [MIN].

Note: Since excessive correction may lead to a

correction data overview during internal

calculations, use the following values for

reference.

[No.2] to [No.5] ± 40 or less

[No.6] to [No.9] ± 50 or less

[No.10] to [No.13] ± 70 or less

[No.14] to [No.17] ± 120 or less

10. Then adjust [MIN] tone [G] so that the adjust-

ment data set two times as much as [MID-L]

tone [G].

This completes [G] color adjustments.

11. Then adjust [MIN] tone [R] and [B].

Select [No.2] [B:] and press the [ENTER] key

on the Remote control transmitter to change to

solid white.

12. Measure the color coordinates of adjustment

point [No.1] and make a note of them.

Assume that they are x = x1, y = y1.

13. Now measure the color coordinates of mea-

surement point [No.2] and adjust [No.2][R:] and

[B:] so that the coordinates are as follows.

x = x1 ± 0.005 , y = y1 ± 0.010 (Target)

x = x1 ± 0.020 , y = y1 ± 0.040

14. Similarly, measure adjustment points [No.3] to

[No.17] and adjust their color coordinates start-

ing in order from the small number points.

This completes [MIN] tone adjustments.

15. Now make similar adjustments for [MID-H] tone.

(Adjust [MID-H] tone [G] so that the adjustment

data set half as many as [MID-L] tone [G].)

16. Now make similar adjustments for [MAX] tone.

(Adjust [MAX] tone [G] so that the adjustment

data set half as many as [MID-L] tone [G].)

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

Adjustment procedure 2

(visual inspection)

1. First adjust [MIN] tone [G:].

2. Select [No.2] [G:].

If the background is [G] monochrome, press the

[ENTER] key on the remote control to change

to solid white.

3. View measurement point [No.2] and [No.3].

Lower the [G] color intensity only of the color

point whose [G] color is more intense than

measurement point [No.1].

4. View measurement point [No.10] and [No.11].

Lower the [G] color intensity only of the color

point whose [G] color is more intense than

measurement point [No.1], and raise the inten-

sity of the point whose color intensity is lower

than measurement point [No.1].

5. Now adjust the [MIN] tone for colors [R] and [B].

6. View measurement points [No.2], [No.3],

[No.10] and [No.11]. Adjust the [R] and [B] of

each measurement point so that they have the

same color as measurement point [No.1].

Adjustment technique:

First, adjust [B:] of the point whose color is to

be adjusted so that it approximates that of

[No.1]. If [R:] is low at this time, the image will

have cyan cast, in which case [R:] is increased.

On the other hand, if [R:] is excessive, the

image will have a magenta cast, in which case

[R:] is decreased.

Overall, a cyan cast makes it easy to see color

shading.

7. Next, view measurement points [No.4], [No.5],

[No.12], [No.13] and make similar adjustments.

Then adjust measurement points [No.6], [No.7],

[No.8], [No.9], [No.14], [No.15], [No.16] and [No.17].

This completes the [MIN] tone adjustments.

9. Make similar another three tones as described

in steps 1 to 8 above.

No. 2 deviation range No. 10 deviation range No. 3 deviation range No. 11 deviation range

No. 4 deviation range No. 12 deviation range No. 5 deviation range No. 13 deviation range

No. 6 deviation range No. 7 deviation range No. 8 deviation range No. 9 deviation range

No. 14 deviation range No. 15 deviation range No. 16 deviation range No. 17 deviation range

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

5. Troubleshooting

Check points

E801

IS01

IS42

IS12

IS13

IS14

IS41

IS11

IS10

IS40

E800

E301

E802

E807

E805

E302 E806 EE01

EASP

E304

P501

P601

P701

PWB assembly MAIN

D301

(POWER)

D303

(LAMP)

D302

(TEMP)

THERMAL SWITCH (TSW)

PWB assembly REMOTE Speaker cable

EK01

S801

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

Power can not be turned on

Are

voltage

supplied at pins (6)

and (8) of E800 on the PWB

assembly MAIN in

standby mode?

Are

voltage supplied

at pins (1) and (3) of E800

on the PWB assembly MAIN

in standby mode?

PWB assembly MAIN

YES

(6): +6.6V

(8): +4.1V

(10): GND

Does LAMP

(D303) or TEMP (D302)

indicator light or

blink?

YES

(1): +14V

(2): GND(for +14V)

(3): +16V

(4): GND(for +16V)

*: Be sure to unplug the power cord before measuring resistance.

Measure

resistance* between pins

(6) and (10), and between

pins (8) and (10) of

E800.

Are all

of the pictures

from video, s-video and

component video ports dis-

played correctly?

Open

0Ω

PWB assembly MAIN

Power unit (circuit)

Termal switch (TSW)

Open

Power unit (circuit)

Fuse on the power unit

(circuit)

Mea-

sure resistance*

between pins (1) and (2),

and between pins (3) and (4)

of E800.

0Ω

PWB assembly MAIN

Power unit (circuit)

Short

Open

Go to the next page

YES

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

Lamp does not light

What

is the state of

LAMP indicator D303

during operation?

Measure

resistance* between

pins (1) and (2) of S801

when the lamp door

is secure.

Lamp door

Re-attach lamp

door

Re-attach PWB

assembly MAIN

PWB assembly MAIN

Blinks

Open

0Ω

Is the

LAMP installation

correct?

Light

install the Lamp

PWB assembly

MAIN

the voltage

at the (1) of

E804 on the PWB

assembly MAIN fixed

to "L" during

warming-

up?

YES

“L” = 0V

Change the

lamp. Does lamp

light?

Lamp

Light

YES

Not light

Power unit (ballast) Power unit (circuit)

What

is the state of

TEMP indicator

D302?

Thermistor

(E1/E2/E3)

Is the

voltage at the (3) of

E804 on the PWB assembly

MAIN set to "L" during

warming-up?

Not light

and blink

PWB assembly MAIN

YES

“L” = 0V

Power unit (ballast)

PWB assembly

MAIN

Are

the voltage

supplied to the pin

(2) of connectors** for

DC fans soon after

the button is

pressed?

the voltage

supplied to the pin

(4) of E801 soon after

the button is

pressed?

Observe

the voltage

waveforms at pin (1) of

connectors for DC fans**

soon after the button

is pressed.

Blinks

E1/E2: 5 to 20kΩ

E3: 0.5 to 2kΩ

NG(open/short)

DC fan

(failed in above check)

Correct waveform is drawn below.

f ≥ 40Hz

PWB assembly

MAIN

NO (0V)

PWB assembly

MAIN

NO (0V)

PWB assembly

MAIN

Correct

Measure

resistance of

E1, E2 and E3 after

disconnecting them

from MAIN

board.

YES

incorrect

Lights

*: Be sure to unplug the power cord

before measuring resistance.

Not light

and blink

**: DC fan connectors are E801,

E802, E806, and E807.

(1V or higher)

(5V or higher)

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

Picture is not displayed.

Are

the splash screen

and the user menu displayed

correctly?

YES

Are all

of the pictures

from video, s-video and

component video ports

displayed correctly?

YES

Is the

picture from RGB

out port displayed correctly

on another monitor

display?

YES

Is the

message of ”

No input is detected on

**” or “Sync is out of range on

**” displayed on the

screen?

Confirm

the LCD Panels

connection to the MAIN

board.

CPC30 connector A/B

PWB assembly MAIN LCD/Lens prism assembly

PWB assembly MAIN

SN74LVC1G126

(IS13/IS14)

EL83021U

(IS10/IS40)

PWB assembly MAIN EL83021U

(IS10/IS40)

SN74LVC1G126

(IS11/IS12/IS41/IS42)

YES

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

PWB assembly Main

Check at operating mode

(Make sure the state of MUTE and Volume)

No sound

infinity

about 8

Speaker

Disconnect

the speaker from the

PWB assembly Main, and

measure its

resistance.

The check after parts change

1. PC power supply OFF

2. Connection of cable

3. Projector starting

4. PC starting

*When not operating :

PC set up change of cable.

Can not control to RS-232C

YES

Use cross cable

Check the

RS-232C cable.

Are pin No. 2 and 3

crossed?

Make sure PC setup

YES

PWB assembly MAIN

Are the

signals input at each

pins on the PWB assembly

Main?

: RX

: TX

EK01

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)

Does the Lamp

on upper left of the

Network connector light

in green?

Can’t communicate with computer

via NETWORK terminal.

Check at operating mode

Make sure Network

hardware

Set IP address and Subnet

Mask in the Settings >

Network menu with manual

operation.

Is IP Address in

the Network > Information menu

set to “0.0.0.0” after waiting

more than 1 minute?

YES

Are

both IP Address

and Subnetmask in the Setting >

Network > Network Info menu set to

"0.0.0.0" after waiting more than

1 minute?

PWB assembly Main

Use new LAN cable

YES

Set IP address and Subnet Mask

in the Advanced Menu > Network

> IP ADORESS and > SUBNETMASK

menu with manual operation.

the DHCP in the

Advanced Menu > Network

> DHCP is on?

Is the computer

connected with the

projector directly?

Subnet Mask is

"255.255.255.0", are

"xxx.yyy.zzz" portion of IP address

setting of computer and

projector

same?

PWB assembly Main

YES

Is there

DHCP server on

the network which the

projector is connected

to?

Make sure those settings

of the projector and

computer are correct.

PWB assembly Network

YES

Use the same IP address

setting except for "N" on

computer and projector.

YES

IP address: xxx.yyy.zzz.N

Are there

any damage to the cable

between computer and

projector?

CP-S245(CC9SMN)/CP-X255/ED-X8255(CC9XMN)/PJ656(CC9XM)

6. Service points

6-1 Lead free solder [CAUTION]

This product uses lead free solder (unleaded) to help preserve the environment. Please read these

instructions before attempting any soldering work.

Lead free solder indicator

Printed circuit boards using lead free solder are engraved with an "F" or "LF".

Properties of lead free solder

The melting point of lead free solder is 40-50˚C higher than leaded solder.

Servicing solder

Solder with an alloy composition of Sn-3.0Ag-0.5Cu or Sn-0.7Cu is recommended.

Although servicing with leaded solder is possible, there are a few precautions that have to be taken. (Not

taking these precautions may cause the solder to not harden properly, and lead to consequent malfunctions.)

Precautions when using leaded solder

Remove all lead free solder from soldered joints when replacing components.

If leaded solder should be added to existing lead free joints, mix in the leaded solder thoroughly after the

lead free solder has been completely melted (do not apply the soldering iron without solder).

Servicing soldering iron

A soldering iron with a temperature setting capability (temperature control function) is recommended.

The melting point of lead free solder is higher than leaded solder. Use a soldering iron that maintains a high

stable temperature (large heat capacity), and that allows temperature adjustment according to the part being

serviced, to avoid poor servicing performance.

Recommended soldering iron:

Soldering iron with temperature control function (temperature range: 320-450˚C)

Recommended temperature range per part:

Part Soldering iron temperature

Mounting (chips) on mounted PCB 320˚C±30˚C

Mounting (chips) on empty PCB 380˚C±30˚C

Chassis, metallic shield, etc. 420˚C±30˚C

(1) PWB assembly MAIN

(2) PWB assembly REMOTE

(3) PWB assembly NETWORK (not PJ656)

(4) PWB assembly BATTERY (not PJ656)

(5) POWER UNIT (BALLAST)

(6) POWER UNIT (CIRCUIT)

The PWB assembly which has used lead free solder

CAUTION

Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead free solder

can splatter at high temperatures (600˚C).

Page is loading ...

Hitachi ED-X8250 series User manual

Brand: Hitachi

Model: ED-X8250 series

Category: Projectors

Type: User manual

Download PDF

report

Hitachi ED-X8250 series User manual

Hitachi ED-X8250 series User manual

Related papers

Other documents